Manual Pelco DX9200HDDI

20 pages 0.7 mb
Download

Go to site of 20

Summary
  • Pelco DX9200HDDI - page 1

    DX9200HDDI Series IDE V ideo Storage Unit C637M-B (10/03) ® INST ALLA TION/OPERA TION ...

  • Pelco DX9200HDDI - page 2

    CONTENTS Section Page REGULA TOR Y NOTICES ............................................................................................................. ......................................................................................... 3 RADIO AND TELEVISION INTERFERENCE ....................................................................... ...

  • Pelco DX9200HDDI - page 3

    C637M-B (10/03) 3 REGULA TORY NOTICES This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th ...

  • Pelco DX9200HDDI - page 4

    4 C637M-B (10/03) IMPORT ANT SAFEGUARDS AND W ARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not ins ...

  • Pelco DX9200HDDI - page 5

    C637M-B (10/03) 5 DESCRIPTION The DX9200HDDI video storage unit is one of the components of the DX9000 system. The storage unit contains up to 14 IDE hard disk drives for storing video information from the DX9000 recorder . Up to four IDE storage units can be connected to a recorder . The storage unit uses redundant arrays of independent disks (RAI ...

  • Pelco DX9200HDDI - page 6

    6 C637M-B (10/03) FRONT VIEW Figure 1 shows the features on the front of the IDE storage unit. Figure 1. Front View 1. Panel: Use the features of this panel to view the configuration of the RAID or to enter the environment menu. Y ou must lower this panel to remove or add hard drives. 2. Hard drive trays: There are 14 hot-swappable hard drive trays ...

  • Pelco DX9200HDDI - page 7

    C637M-B (10/03) 7 11. Up arrow/Quit button: Used in conjunction with the Controller and ENC buttons. Press to scroll through the information on the LCD display , to move through each menu, or to go back to the previous menu. 12. Down arrow/Info button: Used in conjunction with the Controller and ENC buttons. Press to scroll through the information ...

  • Pelco DX9200HDDI - page 8

    8 C637M-B (10/03) INST ALLA TION Make sure the following parts are supplied with the storage unit. 1V ideo Storage Unit with IDE hard drives 2 Power cords (1 USA standard and 1 European standard) 2 External SCSI cables 2 Active terminators (for connecting to SCSI channels) 2 Brackets 6 Screws, M4 x .250-inch, pan head 4 Adjustable support rails 6 S ...

  • Pelco DX9200HDDI - page 9

    C637M-B (10/03) 9 MOUNTING The storage unit can be placed on a flat surface, such as a shelf, or it can be installed in a 19-inch (48.26 cm) wide equipment rack. NOTE: Allow one rack unit (1.75 inches or 4.5 cm) of space above the storage unit for air circulation. To install the storage unit in an equipment rack: 1. Attach the two brackets to each ...

  • Pelco DX9200HDDI - page 10

    10 C637M-B (10/03) STORAGE RECORDER A HOST B HOST A CHANNEL A SCSI CABLE STORAGE RECORDER A RECORDER B HOST B HOST A CHANNEL A CHANNEL A SCSI CABLE SCSI CABLE Figure 5. One Storage Unit/Two Recorder Configuration HARDWARE CONNECTIONS There are five hardware configurations. Y ou can connect one storage unit to one recorder , one storage unit to two ...

  • Pelco DX9200HDDI - page 11

    C637M-B (10/03) 11 CHANNEL A CHANNEL B STORAGE B STORAGE A RECORDER HOST A HOST A SCSI CABLE SCSI CABLE CONNECTING TWO STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Plug the power cords into the units an ...

  • Pelco DX9200HDDI - page 12

    12 C637M-B (10/03) Figure 7. Three Storage Unit/One Recorder Configuration CONNECTING THREE STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Connect a SCSI cable (DX9200HDDI-LCBL) from the Host A Out port o ...

  • Pelco DX9200HDDI - page 13

    C637M-B (10/03) 13 CONNECTING FOUR STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Connect a SCSI cable (DX9200HDDI-LCBL) from the Host A Out port on Storage A to the Host A In port on Storage C. 4. Connec ...

  • Pelco DX9200HDDI - page 14

    14 C637M-B (10/03) OPERA TION The storage unit has been preconfigured to operate using RAID Level 5 or RAID Level 5+1 technology . Pelco recommends RAID Level 5+1. In Level 5+1, a hot spare drive is included. If a hard drive is removed or fails, the redundant data, on the remaining drives, relocates automatically to the hot spare and begins the rec ...

  • Pelco DX9200HDDI - page 15

    C637M-B (10/03) 15 TROUBLESHOOTING What do I do when the voltage warning LED illuminates red and an alarm sounds? This happens when the output DC voltage is under 4.5V or over 5.5V , and under 10.2V or over 13.8V . The ENC global fault LED also illuminates. Press the Exit/Alarm reset button to stop the alarm. A low beep continues to sound. There ma ...

  • Pelco DX9200HDDI - page 16

    16 C637M-B (10/03) SERVICE HOW TO REPLACE A F AN The fans are hot-swappable. The spare part number for the fan is DX9200HDDI-F AN. THUMBSCREW HANDLE THUMBSCRE W HANDLE Figure 9. Replacing a Fan Figure 10. Replacing a Power Supply 1. Loosen the thumbscrew . 2. Pull the screw to lift the handle. 3. Pull out the defective fan. 4. Slide the new fan int ...

  • Pelco DX9200HDDI - page 17

    C637M-B (10/03) 17 HOW TO CHANGE FROM RAID 5 TO RAID 5+1 To change a RAID 5 configuration to a RAID 5+1 configuration, you must add a hot spar e hard drive. A hot spare hard drive becomes the replacement hard drive when a hard drive fails in the RAID 5+1 configuration. Make sure you have the appropri- ate spare drive from Pelco: DX9000DRV-I120 or D ...

  • Pelco DX9200HDDI - page 18

    POWER CONNECTOR 40-PIN ATA CABLE CONNECTOR LEVER RELEASE LEVER ATA CABLE CONNECTOR PORT JUMPER POWER PORT PHILLIPS SCREWS TRAY WITH HARD DRIVE Figure 11. Adding a Hard Drive ...

  • Pelco DX9200HDDI - page 19

    W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/ MC3600 Series); two ...

  • Pelco DX9200HDDI - page 20

    World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada Singapore ® ...

Manufacturer Pelco Category Portable Media Storage

Documents that we receive from a manufacturer of a Pelco DX9200HDDI can be divided into several groups. They are, among others:
- Pelco technical drawings
- DX9200HDDI manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco DX9200HDDI
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco DX9200HDDI.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco DX9200HDDI, service manual, brief instructions and user manuals Pelco DX9200HDDI. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco DX9200HDDI.

Similar manuals

A complete manual for the device Pelco DX9200HDDI, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco DX9200HDDI by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco DX9200HDDI.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco DX9200HDDI - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco DX9200HDDI, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco DX9200HDDI, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco DX9200HDDI - which should help us in our first steps of using Pelco DX9200HDDI
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco DX9200HDDI
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco DX9200HDDI in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco DX9200HDDI?

Use the form below

If you did not solve your problem by using a manual Pelco DX9200HDDI, ask a question using the form below. If a user had a similar problem with Pelco DX9200HDDI it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)