Manual Graco 222791

18 pages 0.27 mb
Download

Go to site of 18

Summary
  • Graco 222791 - page 1

    Instructions–Parts List Monark r Air Motor For use with Graco fluid handling pumps. 180 psi (1.2 MPa, 12 bar) Maximum Air Working Pressure Model 206955, Series K For ST ANCHION TUBE mounting Model 205997, Series K Model 215363, Series D Model 222791, Series D For 3 tie rod mounting Model 207546, Series H For hinged clamp mounting Important Safety ...

  • Graco 222791 - page 2

    2 307043 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Motor Service 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts Drawings and Lists Model 207546 10 . . . . . . . . . . . ...

  • Graco 222791 - page 3

    3 307043 W ARNING SKIN INJECTION HAZARD Spray from the gun/dispensing valve, leaks or ruptured components can inject fluid into your body and cause extremely serious injury , including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury . D Fluid injected into the skin might look like just a cut, but it ...

  • Graco 222791 - page 4

    4 307043 W ARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury . D Ground the equipment and the object being sprayed. Refer to Grounding on page 5. D If there is any static sparking or you feel an electric shock while using ...

  • Graco 222791 - page 5

    5 307043 Installation Grounding W ARNING FIRE AND EXPLOSION HAZARD Before operating the pump, ground the system as explained below . Also read the section FIRE AND EXPLOSION HAZARD on page 4. Proper grounding is an essential part of maintaining a safe system. T o reduce the risk of static sparking, ground the pump. Check your local electrical code ...

  • Graco 222791 - page 6

    6 307043 Air Motor Service Pressure Relief Procedure W ARNING SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying/dispensing acciden- tally . Fluid under high pressure can be injected through the skin and cause serious injury . T o re- duce the risk of an injury from injection, splashi ...

  • Graco 222791 - page 7

    7 307043 Air Motor Service 7. Pull the piston assembly (G) from the air motor base (F), and set it aside. 8. Remove the bearing housing assembly (26 or 27) for all Models except Model 206955. Remove and wipe the seat clean with a cloth. For model 206955, remove retainer ring (3) and bearing (4). Remove seal (2, 27 or 28). 9. Remove the base from th ...

  • Graco 222791 - page 8

    8 307043 Air Motor Service 13. Straighten the lockwires (L*) and remove them from the upper valve nuts (J*). Screw the upper valve nuts off. Remove the trip rod yoke (O), actuator (V), and trip rod (C). 14. Unscrew the bottom valve nuts (K*), and remove the poppets (N*). Make sure the valve bar spring clips (W) are not worn or damaged and that they ...

  • Graco 222791 - page 9

    9 307043 Air Motor Service 6. Install the toggle pins (Z) in the yoke (O). As- semble the toggle assembly (U) by placing a well greased spring onto the toggle arm (T) and then the toggle rocker (S). Place the toggle arm (T) ends of the toggle assembly (U) onto the toggle pins, and snap the pivot pin (S) ends of the toggle assembly into the lugs (P) ...

  • Graco 222791 - page 10

    6 *12 13 9* 10* 11 n 31 n 14 *15 2 21 20 5 18 32 34 33 05704 n 3 n 7 25 24* 8* 9* 1 22 30 4 23* 17 19 Y 36 35 28 29 n 27 NOTE: Seal lips face upward 26 10 307043 Parts HINGED CLAMP MOUNTING: SANIT AR Y Model 207546, Series H, Air Motor Assembly Includes items 1–36 ...

  • Graco 222791 - page 11

    11 307043 Parts HINGED CLAMP MOUNTING: SANIT AR Y Model 207546, Series H , Air Motor Assembly Includes items 1–36 Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 1 14422 SCREW , phillips hd mach; no. 8–32 x 0.375 in. (10 mm) long. 8 2 101578 SCREW , hex head; 5/16 x 0.875 in. (10 mm) long 6 3 n 156698 O-RING; buna-N 1 ...

  • Graco 222791 - page 12

    05705B 10 *16 17 13* 14* 15 n 30 n 18 20 24 25 9 21 31 33 32 n 7 n 11 29 28* 12* 13* 1 Y 37 *19 8 27* 23 26 35 34 NOTE: Seal lips face upward 3 4 n 2 5 36 6 12 307043 Parts ST ANCHION TUBE MOUNTING Model 206955, Series K, Air Motor Assembly Includes items 1–37 ...

  • Graco 222791 - page 13

    13 307043 Parts ST ANCHION TUBE MOUNTING Model 206955, Series K, Air Motor Assembly Includes items 1–37 Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 1 14422 SCREW , phillips hd mach; no. 8–32 x 0.38 in. (10 mm) long. 16 2 n 16H224 SEAL 1 3 101525 RING, retainer 1 4 101526 BEARING 1 5 101578 SCREW , hex head; 5/16 x ...

  • Graco 222791 - page 14

    05706B n 7 *12 13 9* 10* 11 n 31 n 14 *15 3 46,18 36 6 22, 37 32 34 33 n 4 n 19 26 25* 8* 9* 1 Y 43 5 24* 17 23 40 39 29 30 n 28 NOTE: Seal lips face upward 27 21 20, 38, 44 2 14 307043 Parts Model 205997, Series K Air Motor Assembly Includes: 1, 3–19, 23, 25–34, 36–43 Model 215363, Series D Air Motor Assembly Includes: 1, 3–19, 21, 23, 25? ...

  • Graco 222791 - page 15

    15 307043 Parts Model 205997, Series K Air Motor Assembly Includes: 1, 3–19, 23, 25–34, 36–43 Model 215363, Series D Air Motor Assembly Includes: 1, 3–19, 21, 23, 25–34, 37–43 Model 222791, Series D Air Motor Assembly Includes: 1–23, 25–34, 39–43 Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 1 14422 SCR ...

  • Graco 222791 - page 16

    16 307043 Accessories BLEED-TYPE MASTER AIR V AL VE (REQUIRED) 300 psi (21 bar , 2.1 MPa) Maximum Working Pressure Relieves air trapped in the air line between the pump air inlet and this valve when closed. 107141 3/4 npt (m x f) inlet and outlet 107142 1/2 npt (m x f) inlet and outlet SILENCER KIT 215354 Fits Monark Air Motors Models 206955, 22299 ...

  • Graco 222791 - page 17

    17 307043 Dimensional Drawings 05709 1 1.75 in. (298.4 mm) 13.25 in. (336.6 mm) 15.75 in. (400.1 mm) for 206955 5.75 in. (146.1 mm) Mounting Hole Layouts Three 0.34 in. (8.6 mm) diameter holes on 6.38 in. (162.1 mm) bolt circle 3 T ie Rod Pumps 05707 05708 45_ 45_ 2.5 in. (64 mm) 2.5 in. (64 mm) 4 in. (102 mm) 1 in. (25 mm) radius 161322 gasket 5 i ...

  • Graco 222791 - page 18

    18 307043 Graco Standard W arranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from de fec ts in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, e xtended, or limited warranty published by Graco, Graco will, ...

Manufacturer Graco Category Outboard Motor

Documents that we receive from a manufacturer of a Graco 222791 can be divided into several groups. They are, among others:
- Graco technical drawings
- 222791 manuals
- Graco product data sheets
- information booklets
- or energy labels Graco 222791
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco 222791.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco 222791, service manual, brief instructions and user manuals Graco 222791. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco 222791.

Similar manuals

A complete manual for the device Graco 222791, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco 222791 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco 222791.

A complete Graco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco 222791 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco 222791, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco 222791, that we can find in the current document
3. Tips how to use the basic functions of the device Graco 222791 - which should help us in our first steps of using Graco 222791
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco 222791
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco 222791 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco 222791?

Use the form below

If you did not solve your problem by using a manual Graco 222791, ask a question using the form below. If a user had a similar problem with Graco 222791 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)