-
NEC 16 - page 1
...
-
NEC 16 - page 2
...
-
NEC 16 - page 3
l Lift handset. z< PLACING AN OUTSIDE tIiAitUSlNG HANDSFREE DlAllNG * l Depress idle outside line button. l Dial desired telephone number. l Depress ON/OFF button. NOTE: When placing consecutive calls l Depress idle outside line button. the RECALL button may be used to l Dial desired telephone number, disconnect existing call and to l Lift hands ...
-
NEC 16 - page 4
l Lift handset, (Depress ON/Off bution ifequipped * Dial digit “1” to transmit tone signal. with Speakerphone.) NOTE: When calling a Single Line telephone, l Depress ICM button, no voice announcement is available. l Dial desired station number, OR Ring signal will be automatically pro- vided. l Voice announce after hearing tone burst; PLACING A ...
-
NEC 16 - page 5
SETTING CALL BACK REQUEST l Call station and receive “no answer” or Call Waiting Tone. l Dial “#“. l Verify at display: ‘5” = accepted “d” = denied l If accepted, your station number will flash intermittently in the called key set’s display, indicating your “call back request”. SETTING AUTOMATIC CALL BACK l Call station and re ...
-
NEC 16 - page 6
l Depress HOLD button. l Held line button will wink intermittently on your keyset. All other keysets will receive a rapid-flash on that line button. NOTE: When you place an intercom call on hold, the HOLD button will rapid-flash. PLACING CALLS ON EXCLUSIVE HOLD l Depress HOLD button twice. l Held line button will wink intermittently on your keyset. ...
-
NEC 16 - page 7
;i. l Depress HOLD button. l Depress ICM button. l Dial desired station number. l Announce transfer, informing station which line to pick up. NOTE: When transferring a call to a station which does not have that line appearance, the following procedure must be used; l Depress HOLD button. l Depress ICM button. l Dial desired station number and wait ...
-
NEC 16 - page 8
l Depress ADD/ON button. l Dial three digit station number to be programmed. l Depress desired station DSS button (I-20) l Depress ADD/ON button again. INTERCOM CALLING USING STATION DSS BUTTONS l Lift handset. (Depress ONIOfFbutton if equipped with Speakerphone.) l Dial digit “1” to transmit l Depress desired station DSS button. OR tone signal ...
-
NEC 16 - page 9
l Depress speed dial button to be verified (I-20) while keGet is idle. l Read number in display (one digit at a time). l Lift handset or depress ON/OFF button. l Depress idle outside line button. l Dial “#” and two-digit access code. (IO-IO> l When party has answered, use handset to begin conversation, (Hcmdsef not required when equipped wit ...
-
NEC 16 - page 10
ATHREE-PARTYCONFERENCE l Establish first call. l Depress HOLD button, l Establish second call. l Depress ADD/ON button. l Depress held line button (or HOLD button for intercom call). NOTE: A three-party conference may consist of the following: 3 internal stations 2 internal stations + 1 outside line 1 internal station + 2 outside lines AFOUR-PARTYC ...
-
NEC 16 - page 11
SETTING l Depress ON/OFF button. l Depress ICM button. l Dial “46” l Dial station number calls should be forwarded to. l Dial “I” for all calls to be forwarded. l Dial “2” for calls to be forwarded only when your station is busy, l Receive confirmation tone. l Depress ON/OFF button. NOTE: The HOLD LED will be lit steadily when call forw ...
-
NEC 16 - page 12
l Lift handset. (Depress ONIOFFbufton if l Depress ICM button. equipped with Speakerphone.) l Dial “2” to establish connection. l Lift handset or depress ON/OFF button. l Depress idle outside line button. l Dial “W’. l When party has answered, use handset to talk. (Handset not required when equipped with Speakerphone.) SETTING l Depress DND ...
-
NEC 16 - page 13
SINGLE LINE TELEPHONE l Lift handset, listen for dial tone. l Dial desired station number. l Wait for party to answer. l Lift handset, listen for dial tone. l Dial outside line access code (9,8, or 7). l Dial telephone number. *Ask party to hold. l Depr;ess switchhook momentarily, listen for second dial tone. l Place a second call if desired, NOTE ...
-
NEC 16 - page 14
l Inform party of transfer, l Depress switchhook momentarily, listen for second dial tone. l Dial desired station number immediately. l Depress switchhook momentarily, when station answers, l Confirm transfer and replace handset. NOTE: If station is busy or does not answer, depress switchhook momentarily to return to held party. l Establish first c ...
-
NEC 16 - page 15
l Lift handset, l Dial “40”. l Dial two digit access code, 20 through 29. 0 Dial outside line access code, 9,8, or 7. l Dial telephone number. l Replace handset. ACCESSING STATION SPEED DIALING l Lift handset. l Dial “#“. l Dial two digit access code, 20 through 29, l Lift handset. l Dial ‘*#“. l Dial Iwo digit access code, 10 through 1 ...
-
NEC 16 - page 16
SETTING l Lift handset. l Dial “46”. l Dial station number you wish your calls to be forwarded to. l Dial rrly’ for all calls to be forwarded. l Dial “2” for calls to be forwarded only when your phone is busy. CANCELLING l Lift handset. l Dial 46 and replace handset, l Lift handset. l Dial 2. l You will be connected to the incoming interc ...
-
NEC 16 - page 17
l Lift handset. ANSWERING T Dial internal zone access code (51,52,53 or 50). l Lift handset, l Voice page. l Dial 55. l Lift handset. ANSWERING l Dial external zone page access code (61,62,63 or 60). l Lift handset. l Voice page. l Dial 65. Account code entry applies only to those systems equipped with station message detail service (SMDS), l Dial ...
-
NEC 16 - page 18
DIRECTORY NOTES Name Area Code &Number ...
Do you have a question concerning NEC 16?
Use the form below
If you did not solve your problem by using a manual NEC 16, ask a question using the form below. If a user had a similar problem with NEC 16 it is likely that he will want to share the way to solve it.