Manual Makita EW200TR

20 pages 0.89 mb
Download

Go to site of 20

Summary
  • Makita EW200TR - page 1

    PUMP EW2OOTR MODEL EW3OOTR EW400TR INSTRUCTION MANUAL I ISSUEEMD-PU0835 I piEGKq ...

  • Makita EW200TR - page 2

    ...

  • Makita EW200TR - page 3

    FOREWORD Thank you for purchasing a Makita trash pump. This manual covers operation and maintenance of trash pumps. All information in this publication is based on the latest product infor- mation available at the time of approval for printing. Please read this manual carefully before operating. CONTENTS Page 1. PUMP SAFETY 1 2. COMPONENTS 2 3. PRE ...

  • Makita EW200TR - page 4

    ID PUMP SAFETY Please make sure you review each precaution carefully. SURROUNDINGS H Operate the pump on a stable, level surface free of small rocks, loose gravel, etc. H Keep pump at least 3 feet (1 meter) away from buildings. H Keep pump away from flammables and other hazardous materials (trash, rags, lubricants, explosives). FIRE PREVENTION m Be ...

  • Makita EW200TR - page 5

    Spark plug Fuel cock Speed control lever Fuel tank Plug(priming) Pump strainer Drain plug (at two places) -2- ...

  • Makita EW200TR - page 6

    3. PREPARATIONS FOR STARTING 1. Connect the suction hose. Use a reinforced-wall or wire braided hose to prevent suction collapse. Since the pump’s self-priming time is directly proportional to hose length, a short hose is recommended. tion hose. Gravel or debris sucked into the pump will cause serious 2. Connect the discharge hose. When using a f ...

  • Makita EW200TR - page 7

    4. Check the fuel level. If level is low, fill to the shoulder of the fuel filter. Use fresh, clean automotive gasoline. 5. Check the priming water. It is recommended that the water chamber of pump casing should be primed with full of water before operating. ICAUTION], . Never attempt to operate the pump without priming water or the pump will overh ...

  • Makita EW200TR - page 8

    4. STARTING THE ENGINE 1. Open the fuel cock. 2. Set the speed control lever to “START.” -. .. . . . EW400TR 3. Close the choke. m If the engine is warm or the ambient temperature is high, close the choke half-way, or keep it open fully. If the engine is cold, or the ambient temperature is low, close the choke. . -5- Choke knob -I EW400TR I ...

  • Makita EW200TR - page 9

    4. Pull the starter handle slowly until re- sistance is felt. This is the "compression" point. Return the handle to its original position and pull swiftly. Do not pull out the rope all the way. I After starting the engine, allow the starter handle return to its original position while still holding the handle. -6- ...

  • Makita EW200TR - page 10

    5. OPERATION 1. After starting the engine, gradually open choke by turning the choke lever and finally keep it open fully. H Do not fully open the choke immediately when the engine is cold or the ambient temperature is low, because the engine may stop. 2. After the engine starts, set the speed control lever at the low speed position (L) and warm it ...

  • Makita EW200TR - page 11

    6. STOPPING THE ENGINE 1. Set the speed control lever to the low speed position and allow the engine to run at low speed for 2 or 3 minutes before stopping. 2. Keep depressing the STOP BUTON until the engine stops. Do not stop the engine suddenly when it is running at high speed. 3. Close the fuel cock. 4. Pull the starter handle slowly and return ...

  • Makita EW200TR - page 12

    DAILY INSPECTION Before running the pump, check the following service items: Enough fuel. m Excessive vibration, noise. Clean air cleaner element. Safe surroundings. Enough clean engine oil. D Leakage of gasoline and engine oil. Loose or broken bolts and nuts. Check the priming water. 8 hours (daily) PERIODIC INSPECTION Periodic maintenance is vita ...

  • Makita EW200TR - page 13

    a. "HOW TOWAINTENANCE INSPECTING THE SPARK PLUG w Clean off carbon deposits on the plug electrode using a plug cleaner or wire brush. Check electrode gap. Adjust it to between 0.02 and 0.03 inches. (0.6 and 0.7") ENGINE OIL CHANGE Initial oil change ...... 20 hours of operation Thereafter.. .Every 50 hours of operation :CAUTION]- Make sur ...

  • Makita EW200TR - page 14

    SERVICING THE AIR CLEANER Maintaining an air cleaner in proper condition is very important. Dirt induced through im- properly installed, improperly serviced or in- adequate elements, wears out engines. Keep the element always clean. (a) Unlock the cover and remove the cleaner element. (b) Inner element:Wash the element with kerosene, then soak it i ...

  • Makita EW200TR - page 15

    Pump does not run. I Pumping volume is small. Pump does not self-prime. 7 c Engine does not start. (See page 13.) Sticking of impeller (Disassemble and clean.) Sucking air at suction side (Check piping at suction side.) Drop in engine output (Consult your nearest dealer.) Breakage of mechanical seal (Consult your nearest dealer.) High suction lift ...

  • Makita EW200TR - page 16

    fore you take the pump to your Makita dealer. If you still have trouble after com- pleting the checks, take the pump to your nearest Makita dealer. 1. Remove the plug and connect it to the plug cap. Pull the starter handle while putting the plug against the engine ground. 2. Try with a new plug if the spark is weak or no spark flies. 3. The ignitio ...

  • Makita EW200TR - page 17

    10. PREPARATIONS FOR STORAGE ~~~ ~ I Drain all water from the drain plug. , I When retightening drain plug, be sure to clean the drain plug and the thread of casincl. Otherwise, the [CAUTION 1u thread may be da6aged. II J 1 Remove the strainer cup, and open the strainer cock to discharge the fuel from the fuel tank. Remove the carburetor float cham ...

  • Makita EW200TR - page 18

    11 OIL SENSOR INSTRUCTIONS OIL SENSOR (OPTION) (a) The oil sensor detects the fall in oil level in the crankcase and automatically stops the engine when the oil level falls down below the predetermined level. (b) When engine has stopped automatically, check the oil level. Refill engine oil to the upper level and restart the engine. (c) If the engin ...

  • Makita EW200TR - page 19

    ...

  • Makita EW200TR - page 20

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period. retum the COMPLETE tool, freight ...

Manufacturer Makita Category Septic System

Documents that we receive from a manufacturer of a Makita EW200TR can be divided into several groups. They are, among others:
- Makita technical drawings
- EW200TR manuals
- Makita product data sheets
- information booklets
- or energy labels Makita EW200TR
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita EW200TR.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita EW200TR, service manual, brief instructions and user manuals Makita EW200TR. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita EW200TR.

Similar manuals

A complete manual for the device Makita EW200TR, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita EW200TR by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita EW200TR.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita EW200TR - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita EW200TR, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita EW200TR, that we can find in the current document
3. Tips how to use the basic functions of the device Makita EW200TR - which should help us in our first steps of using Makita EW200TR
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita EW200TR
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita EW200TR in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita EW200TR?

Use the form below

If you did not solve your problem by using a manual Makita EW200TR, ask a question using the form below. If a user had a similar problem with Makita EW200TR it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)