Manual Kicker 10ZXM3504

28 pages 0.71 mb
Download

Go to site of 28

Summary
  • Kicker 10ZXM3504 - page 1

    ZXM MARINE AMPLIFIER ZXM350.4 English Version Versión Español Amplificador del la Serie ZXM.4 Deutsche Version Stereoverstärker der ZXM.4-Serie Version Francaise Amplificateur de série ZXM.4 LIVIN’ LOUD 2010 ZXM 350.4 RevD.indd 1 2010 ZXM 350.4 RevD.indd 1 1/15/2010 11:17:36 AM 1/15/2010 11:17:36 AM ...

  • Kicker 10ZXM3504 - page 2

    2 ZXM AMPLIFIERS ZXM.4-SERIES AMPLIFIERS Owner’ s Manual INST ALLA TION Mounting: Choose a structurally sound location to mount your KICKER amplifi er . Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er . If possible, mount the ...

  • Kicker 10ZXM3504 - page 3

    3 Model External Fuse Power/Ground W ire ZXM350.4 1 x 40 Ampere 8 Gauge source unit high-level speaker outputs to amplifi er shield + – core conductor GND REM +12V 12V battery external fuse protection LED remote turn-on (see page 5)  18” (45cm) Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to y ...

  • Kicker 10ZXM3504 - page 4

    4 ZXM AMPLIFIERS AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 LL RR L+ L- R+ R- L+ L- R+ R- BRIDGED OPERA TION (MONO) minimum impedance of 4 ohms signal in AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 LL RR L+ L- R+ R- L+ L- R+ R- STEREO-AND-MONO-SIMUL T ANEOUSL Y (SAMS) OPERA TION minimum impedance of 4 ohms bridged (mono) and 2 ohms per channel ste ...

  • Kicker 10ZXM3504 - page 5

    5 OPERA TION AUTO TURN ON +12V DC AUDIO OFFSET XOVER2 OFF HI LO XOVER1 OFF HI LO LO HI AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 INPUT LEVEL OFF ON FADER LL RR Automatic T ur n-On Selection: The ZXM series offers three different automatic turn-on modes that can be selected on the end panel; +12V , DC Offset, and Audio. Using either the DC Offset ...

  • Kicker 10ZXM3504 - page 6

    6 ZXM AMPLIFIERS TROUBLESHOOTING If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated aqua badge on top of the amplifi er denoting the power state of the amp in addition to ...

  • Kicker 10ZXM3504 - page 7

    7 CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can result in blown amplifi er fuses as well as the failure of other critical systems in the vehicle. If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Deal ...

  • Kicker 10ZXM3504 - page 8

    8 AMPLIFICADOR ZXM AMPLIFICADOR DE LA SERIE ZXM.4 Manual del propietario INST ALACIÓN Montaje: Escoja un lugar estructuralmente sólido para montar el amplifi cador KICKER. Asegúrese de que no haya nada por detrás de dónde van a entrar los tornillos. Escoja un lugar en que queden por lo menos 4 plg. (10 cm) de espacio abierto de ventilación a ...

  • Kicker 10ZXM3504 - page 9

    9 Modelo Fusible Externo Cable de Alimentación y Conexión a T ierra ZXM350.4 1 x 40A Calibre 8 altavoz procedente de las salidas de altavoz de alto nivel de la unidad fuente y conéctelo a las entradas RCA del panel de extremo del amplifi cador o simplifi car la instalación mediante un ZISL KICKER como se muestra a continuación . Mantenga el ...

  • Kicker 10ZXM3504 - page 10

    10 AMPLIFICADOR ZXM FUNCIONAMIENTO EN PUENTE (MONOFÓNICO) impedancia mínima de 4 ohmios en puente FUNCIONAMIENTO SIMUL TÁNEO EN ESTEREOFÓNICO Y MONOFÓNICO impedancia mínima de 4 ohmios en monofónico y 2 ohmios por canal en estereofónico simultáneamente woofer woofer woofer señal de entrada AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 LL RR ...

  • Kicker 10ZXM3504 - page 11

    11 FUNCIONAMIENTO AUTO TURN ON +12V DC AUDIO OFFSET XOVER2 OFF HI LO XOVER1 OFF HI LO LO HI AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 INPUT LEVEL OFF ON FADER LL RR Selección de Encendido Automático: La serie ZXM ofrece tres modalidades de encendido automático que se pueden seleccionar en el panel de extremo: +12V , compensación de CC y audio ...

  • Kicker 10ZXM3504 - page 12

    12 AMPLIFICADOR ZXM RESOLUCIÓN DE PROBLEMAS Si su amplifi cador parece no estar funcionando, revise lo obvio primero: fusibles quemados, conexiones malas o incorrectas, posición incorrecta de los selectores de crossover y amplifi cación, etc. Hay una insignia turquesa iluminada en la parte de arriba del amplifi cador de la serie ZXM de KICKER ...

  • Kicker 10ZXM3504 - page 13

    13 Nota importante: Los altavoces modernos de alto rendimiento tienen menos resistencia a la CC que los de antes. Los altavoces de componente o coaxiales de KICKER tienen un valor nominal de 4 Ω (algunas resistencias de CC pueden llegar a 3 Ω ) y funcionan con cualquier unidad fuente o amplifi cador diseñado para funcionar con 4 Ω de carga. Si ...

  • Kicker 10ZXM3504 - page 14

    14 ZXM VERSTÄRKER VERSTÄRKER DER ZXM.4 SERIE Benutzerhandbuch INST ALLA TION Befestigung: Wählen Sie für die Installation des KICKER-V erstärkers eine strukturell stabile Stelle. Vergewissern Sie sich, dass sich hinter der Einschraubposition der Schrauben nichts befi ndet. Wählen Sie eine Stelle, die mindestens 10 cm Lüftungsfreiraum für d ...

  • Kicker 10ZXM3504 - page 15

    15 Modell Externe Sicherung Massekabel ZXM350.4 1 x 40 Ampere 8 GA verbinden Sie das Kabel mit den RCA-Eingängen an der Endplatte des V erstärkers, oder V ereinfachung der Installation, indem Sie ein KICKER ZISL wie unten gezeigt . Achten Sie beim V erlegen dieser Audiokabel darauf, dass sie Werks-Kabelbäume und andere Stromkabel nicht berühren ...

  • Kicker 10ZXM3504 - page 16

    16 ZXM VERSTÄRKER BRÜCKENBETRIEB (MONO) Minimalimpedanz von 4 Ohm GLEICHZEITIGER STEREO- UND MONO-BETRIEB (SAMS) Mindestimpedanz von 4 Ohm (Mono) bzw . 2 Ohm pro Kanal (Stereo) bei gleichzeitigem Betrieb Tieftöner Tieftöner Tieftöner AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 LL RR L+ L- R+ R- L+ L- R+ R- AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R ...

  • Kicker 10ZXM3504 - page 17

    17 BETRIEB AUTO TURN ON +12V DC AUDIO OFFSET XOVER2 OFF HI LO XOVER1 OFF HI LO LO HI AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 INPUT LEVEL OFF ON FADER LL RR Automatische Einschaltung: Die ZXM-Serie bietet drei verschiedene automatische Einschaltmethoden, die an der Endplatte gewählt werden können: +12V , DC Offset und Audio. Wenn Sie „DC Off ...

  • Kicker 10ZXM3504 - page 18

    18 ZXM VERSTÄRKER PROBLEMBEHEBUNG Wenn der V erstärker nicht zu funktionieren scheint, sollten Sie zuerst offensichtliche Faktoren prüfen, wie durchgebrannte Sicherungen, schlechte oder fehlerhafte V erkabelung, inkorrekte Einstellung des Crossover - Schalters und der V erstärkungsregler etc. Oben am Verstärker befi ndet sich eine blaugrün L ...

  • Kicker 10ZXM3504 - page 19

    19 Autoradio zur Karosserie zu verlegen. Hinweis: Moderne Hochleistungslautsprecher haben einen geringeren Gleichstrom-Widerstand, als dies früher der Fall war . Die KICKER Koaxial- und Komponentenlautsprecher haben eine Impedanz von 4 Ohm (manche Gleichspannungs-Widerstände können auch nur 3 Ohm betragen) und können mit jedem V erstärker zusa ...

  • Kicker 10ZXM3504 - page 20

    20 AMPLIFICA TEUR ZXM AMPLIFICA TEUR SÉRIE ZXM.4 Manuel d’utilisation INST ALLA TION Montage: Choisissez un emplacement de structure saine pour monter votre amplifi cateur KICKER. Assurez- vous que l’arrière de l’emplacement où vous allez enfoncer les vis ne comporte aucun élément. Choisissez un endroit assurant au moins 10 cm (4 po) de ...

  • Kicker 10ZXM3504 - page 21

    21 Modèle Fusible Externe Fil de Masse / Alimentation ZXM350.4 1 x 40 Ampères Calibre 8 de niveau d’entrée sur le panneau d’extrémité de l’amplifi cateur à la position « HI ». Sertissez et soudez les connecteurs RCA à l’extrémité du fi l du haut-parleur venant des sorties de haut-parleur de haut niveau sur l’appareil source e ...

  • Kicker 10ZXM3504 - page 22

    22 AMPLIFICA TEUR ZXM FONCTIONNEMENT PONTÉ (MONO) impédance minimum de 4 ohms FONCTIONNEMENT SIMUL T ANÉ STÉRÉO ET MONO (SAMS) impédance minimum simultanément de 4 ohms en mono et 2 ohms par canal en stéréo woofer woofer woofer Entrée du signal Entrée du signal AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 LL RR L+ L- R+ R- L+ L- R+ R- AMP ...

  • Kicker 10ZXM3504 - page 23

    23 UTILISA TION AUTO TURN ON +12V DC AUDIO OFFSET XOVER2 OFF HI LO XOVER1 OFF HI LO LO HI AMP1 AMP1 L+ L- R+ R- AMP2 L+ L- R+ R- AMP2 INPUT LEVEL OFF ON FADER LL RR Sélection de Mise sous T ension Automatique : La série ZXM est dotée de trois modes différents de mise sous tension automatique pouvant être sélectionnés au panneau d’extrémit ...

  • Kicker 10ZXM3504 - page 24

    24 AMPLIFICA TEUR ZXM EN CAS DE DIFFICUL TÉ Si votre amplifi cateur ne marche pas, vérifi ez d’abord les possibilités évidentes comme les fusibles sautés, les branchements incorrects ou desserrés, le mauvais réglage des commandes de gain et du commutateur du fi ltre, etc. En plus de la DEL de protection située sur le panneau d’extré ...

  • Kicker 10ZXM3504 - page 25

    25 ZXM350.4 60 x 4 @ 4 ohms, 14.4V C.C., 1% de Distorsion Harmonique T otale, CEA-2006 (Watts) Rapport Signal sur Bruit -95 CEA-2006 (réf. : 1W , pondéré A) Remarque : La résistance c.c. des haut-parleurs modernes à hautes performances est inférieure à ce qui existait auparavant. Les haut-parleurs coaxiaux et des composants KICKER ont une r? ...

  • Kicker 10ZXM3504 - page 26

    26 ZXM AMPLIFIERS ELECTRONICS LIMITED W ARRANTY KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for TWO (2) YEARS from date of original purchase with receipt. ...

  • Kicker 10ZXM3504 - page 27

    27 P .O. Box 459 • Stillwater , Oklahoma 74076 • USA • (405) 624–8510 INTERNA TIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specifi c procedures for your country’ s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! T urning up a ...

  • Kicker 10ZXM3504 - page 28

    ©2009 Stillwater Designs 2010 ZXM 350.4 RevD.indd 28 2010 ZXM 350.4 RevD.indd 28 1/15/2010 11:17:53 AM 1/15/2010 11:17:53 AM ...

Manufacturer Kicker Category Marine Instruments

Documents that we receive from a manufacturer of a Kicker 10ZXM3504 can be divided into several groups. They are, among others:
- Kicker technical drawings
- 10ZXM3504 manuals
- Kicker product data sheets
- information booklets
- or energy labels Kicker 10ZXM3504
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kicker 10ZXM3504.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kicker 10ZXM3504, service manual, brief instructions and user manuals Kicker 10ZXM3504. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kicker 10ZXM3504.

Similar manuals

A complete manual for the device Kicker 10ZXM3504, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kicker 10ZXM3504 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kicker 10ZXM3504.

A complete Kicker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kicker 10ZXM3504 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kicker 10ZXM3504, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kicker 10ZXM3504, that we can find in the current document
3. Tips how to use the basic functions of the device Kicker 10ZXM3504 - which should help us in our first steps of using Kicker 10ZXM3504
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kicker 10ZXM3504
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kicker 10ZXM3504 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kicker 10ZXM3504?

Use the form below

If you did not solve your problem by using a manual Kicker 10ZXM3504, ask a question using the form below. If a user had a similar problem with Kicker 10ZXM3504 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)