Manual Xerox C3000

298 pages 10.98 mb
Download

Go to site of 298

Summary
  • Xerox C3000 - page 1

    FAX Option Type C3000 Operating Instructions Facsimile Reference Read this manual carefully before yo u use this machi ne and keep it h andy for future reference. For safe and corre ct use, be sur e to rea d the Safety Informatio n in "About This Machi ne" before using the ma chine. Transmission Other Transmission Features Reception Chang ...

  • Xerox C3000 - page 2

    Introduction This manual contains detailed instructions and note s on th e operation and use of this ma chine. For your safety and benefit, read this manual carefully be fo re using the machine. Kee p this manual in a handy place for quick reference. Notes Some illustrations in this manual might be slightly diffe rent from the machine. Certain opti ...

  • Xerox C3000 - page 3

    i Manuals for This Machine Refer to the manuals that are relevant to what y ou want to do w ith the machine. ❖ About This Machine Be sure to read the Safety Informatio n in this manual before using the ma- chine. This manual provides an introductio n to the functions of the mac hine. It also explains the control panel , preparation procedures for ...

  • Xerox C3000 - page 4

    ii ❖ Other manuals • PostScript3 Supplement •U N I X S u p p l e m e n t • Manuals for DeskTopBinder Li te • DeskTopBinder Lite Setup Guide • DeskTopBinder Introdu ction Guide •A u t o D o c u m e n t L i n k G u i d e Note ❒ Manuals provided are specific t o machine types. ❒ Adobe Acrobat Reader/Adobe Reader must be installed in ...

  • Xerox C3000 - page 5

    iii TABLE OF CONTENTS Manuals for This Machine .............................................. ........................................ i NOTICE ............................................ ..................................................... .................. 1 Important Safety Instructions ........................................................ ...

  • Xerox C3000 - page 6

    iv Scan Settings ............................................. ..................................................... ..... 47 Scan Type ............. .............. .............. .............. .............. .............. .............. .............. . 47 JBIG Transmission ......... ................ .............. .............. .............. ...

  • Xerox C3000 - page 7

    v 2. Other Transmission Features Sending at a Specific Time (Send Later) ......................................................... 123 Requesting a Reception Notice .......................... .............................................. 125 Setting an E-mail Destination as a BCC . ................................ ......................... 127 Con ...

  • Xerox C3000 - page 8

    vi Printing Options .............................................................. ................................... 163 Print Completion B eep ................. .............. .............. ................. .............. .............. . 163 Checkered Mark ........................ .............. .............. .............. .............. .. ...

  • Xerox C3000 - page 9

    vii Printing/Deleting Received and Stored Documents (Print/Delete Stored Reception File) .............................................................. 206 Printing Received and Stored Do cuments ...... .......................... .............. .............. . 207 Deleting Received and Stored Documents ................... ................. ....... ...

  • Xerox C3000 - page 10

    viii Specifying Options .......................... .............. .............. .............. .............. ............... 249 To send a fax document at a specific time ....................... .............. ................. .... 249 To print a sender stamp..................... .............. .............. .............. .............. ...... ...

  • Xerox C3000 - page 11

    1 NOTICE ❖ Note to users in the Un ited States of America ❖ Note: This equipment has been tested and fo und to comply with the limits for a Class B digital device, pursuant to Pa rt 15 of the FCC Rules. These l imits are designed to provide reasonable protection against harm ful interfer- ence in a resident ial installat ion. This equipm ent ge ...

  • Xerox C3000 - page 12

    2 ❖ Note to users in Canada ❖ Note: This Class B digital apparatus co mplies with Canadian ICES-003. ❖ Remarque concernant les utilisateurs au Can ada ❖ Avertissement: Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. ...

  • Xerox C3000 - page 13

    3 Important Safety Instructions Caution When using your tele phone equipment, basic safety precautions sho uld always be followed to reduce the risk of fire, electric shock and injury to persons, includ- ing the following: • Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a we t basemen ...

  • Xerox C3000 - page 14

    4 How to Read This Manual Symbols This manual uses the foll owing symbols: Indicates important sa fety notes. Ignoring these notes could resu l t i n s e r i o u s i n j u r y o r d e a t h . B e s u r e t o r e a d t h e s e notes. They can be found in the “Sa fety Informa tion” section of About This Ma- chine. Indicates important sa fety note ...

  • Xerox C3000 - page 15

    5 Reading the Display This section ex plains how to u se cont rol panel and screen-displayed keys. The display guides you through operatio ns, shows messages, machine status, and destinations registered in the destination lists. If you press th e { Facsimile } or { Clear Modes } key during operation, the standby display appears. Note ❒ This machi ...

  • Xerox C3000 - page 16

    6 Reading the Display Panel and Using Keys This section explains key functions and me ssages that appear on the control panel. ❖ Initial Display 1. Displays the date, time, and ma- chine status. Displays the name, fac- simile number of the destination, and the size of the original when transmitting. W h e n u s e r a u t h e n t i c a t i o n i s ...

  • Xerox C3000 - page 17

    7 13. Allows you to set various fea- tures for transmission. 14. Allows you to set a sender. 15. Allows you to check the number of “Transmission Standby File(s)”, “Memory Lock File(s)”, and “RX Print Standby File(s)”. 16. Displays Quick Operation keys set for frequently used functions. [ TX File Status ] and [ RX File Status ] are pre- ...

  • Xerox C3000 - page 18

    8 Simplified Display This section explains how to switch to the simplified di splay. When you press the { Simplified Display } key, the screen changes from the initial display to the simplified di splay. Letters and keys are displayed at a la rger size, making operations easier. ❖ Example of a simplified display 1. [ Key Color ] Press to change t ...

  • Xerox C3000 - page 19

    9 Function List This section explains various items that can be specified in the Facsimil e Fea- tures menu. Press the { User Tools/Counter } key to display the Facsimile Features menu. For details about the settings, see “Facsimi le Features”, General Settings Guide. ❖ General Settings ❖ Scan Settings Function name Description Quick Operat ...

  • Xerox C3000 - page 20

    10 ❖ Send Settings ❖ Reception Settings Function name Description Max. E-mail Size Specify to limit the size of e-mail messages that are transmitted, if receivers limit e-mail size, or you cannot send large size e-mail for some reason. Program / Change / De lete Standard Mes- sage Program standard messages to be printed at the top of the first ...

  • Xerox C3000 - page 21

    11 ❖ Initial Settings Reference “Facsimile Features”, General Settings Guide Paper Tray Use this function to print fax docum ents re- ceived from programmed senders and fax documents from other senders, using differ- ent paper trays. Specify Tray for Lines Specify a pape r tray for each line (telephone, Internet Fax, IP-Fax). Folder Transfer ...

  • Xerox C3000 - page 22

    12 ...

  • Xerox C3000 - page 23

    13 1. Transmission This section explains basic transmission operations such as specifying a trans- mission mode or destination. Transmission Modes There are two types of transmis sion: • Memory Transmission • Immediate Transmission Important ❒ I t i s r e c o m m e n d e d t h a t y o u c a l l t h e receiver and confirm with them when sendin ...

  • Xerox C3000 - page 24

    Transmission 14 1 Normally the machine is in the Memory Transmission mode. To switch the mode to Immediate Transmission, press [ Immed. TX ] . Note ❒ You can set the machine to enter Memo ry Transmission mode or Immediate Transmission mode right aft er the power is turned on o r the { Clear Modes } key is pressed. See “Registering a pr iority f ...

  • Xerox C3000 - page 25

    Transmission Modes 15 1 ❖ When sending to an Internet Fax destination Press [ Internet Fax ] to switch the type of transmission to Internet Fax. Reference p.25 “IP-Fax Functions” p.29 “Internet Fax Functions” Memory Transmission Memory transmission mode has standa rd fax, Internet Fax and IP-Fax. Important ❒ If there is a power failur e ...

  • Xerox C3000 - page 26

    Transmission 16 1 C Make the scan settings you require. D Using the number keys or a Destination key, specify a destination. If you make a mistake, press the { Clea r/Stop } key, and then enter the correct number. To select a destination from the Addr ess Book, see “Using the Address Book to Specify Destinations”. E When sending the same origin ...

  • Xerox C3000 - page 27

    Transmission Modes 17 1 F Specify the next destination. Press [ Fax ] or [ Internet Fax ] to switch the transmission type between fax/IP- Fax and Internet Fax. A fax number, e-mail address and IP-Fax destination can be specified simul- taneously. G Press the { Start } key. Note ❒ If the combined tota l number of programmed desti nations exceeds t ...

  • Xerox C3000 - page 28

    Transmission 18 1 Sending multiple original s using the exposure glass Follow these steps to send multiple origi nals using t he exposure gla ss. A Make sure [ Immed. TX ] is not highli ghted. B Place the first page of the original face down on t he exposure glass. C Specify a destination. D Make the scan settings you require. E Press the { Start } ...

  • Xerox C3000 - page 29

    Transmission Modes 19 1 Parallel Memory Transmission This function di als while the o riginal is be ing scanned. Standard Memory Transmission stores th e original in memory, then dials the destination. However, Para llel Memory Transmission a llows you to confirm the connection status quickly. In addition, th is function scans the original faster t ...

  • Xerox C3000 - page 30

    Transmission 20 1 Automatic Redial If a fax document could not be sent be cause the line was busy or an error oc- curred during transmission, the line is sw itched to another at five-minute inter- vals and redial is attempted up to five times. If redialing fails after four redials, the machine cancels the transmission and prints a Communication Res ...

  • Xerox C3000 - page 31

    Transmission Modes 21 1 Note ❒ To avoid accidentally pressing the wr ong Destination key, you can set the machine so that ea ch time a destinat ion is added using a De stination ke y, [ Add ] must be pressed. Make the setting in User Paramet ers (switch 17, bit 2) in the Facsimile Features menu. Reference p.63 “Simultane ous Broadcast Usin g Mu ...

  • Xerox C3000 - page 32

    Transmission 22 1 C Select the scan settings you require. D Using the number keys or a Destination key, specify a destination. If you make a mistake, press the { Clea r/Stop } key, and then enter the correct number. To select a destination from the Addr ess Book, see “Using the Address Book to Specify Destinations”. E Press the { Start } key. T ...

  • Xerox C3000 - page 33

    Transmission Modes 23 1 Sending multiple original s using the exposure glass Follow these steps to send multiple origi nals using t he exposure gla ss. A Press [ Immed. TX ] . B Place the first page face down on the exposure glass. C Specify a destination. D Make the scan settings you require. E Press the { Start } key. F Place the next original on ...

  • Xerox C3000 - page 34

    Transmission 24 1 Displaying Confirmation of Transmission On this screen you can check the destination, transmission mode, and other transmission settings before tr ansmitting . A Press [ Check Modes ] , and then check the transmission settings. The following display appears. B After checking the settings on the display, press [ Exit ] . ...

  • Xerox C3000 - page 35

    IP-Fax Functions 25 1 IP-Fax Functions The IP-Fax function sends or receives documents between t wo facsimiles direct- ly via a TCP/ IP network. This function has the following advantag es and is suitabl e for communica tion within the same LAN: • Reducing communication costs • Communicating between IP-Faxes at hi gher speed than by standard fa ...

  • Xerox C3000 - page 36

    Transmission 26 1 You can receive IP-Faxes in the sa me manner as standard faxes. Important ❒ To use IP-Fax functions, this machine must be connected to a LAN and set up correctly under Initial Settings in the Facsimile Features menu. ❒ The facsimile function of this machine cannot be used with IPv6. ❒ Before using this function, configure th ...

  • Xerox C3000 - page 37

    IP-Fax Functions 27 1 Reference p.147 “Types of Reception” “Connecting the Machine”, General Settings Guide “System Settings”, General Settin gs Guide “Facsimile Features”, General Settings Guide Terminology The following are words you sh ou ld know when using IP-Fax: ❖ H.323 A multimedia communication protocol that sends or recei ...

  • Xerox C3000 - page 38

    Transmission 28 1 Notes on Using IP-Fax The following are notes about us ing IP-Fax: • You may not be able to send to a firewall-protected network. • You cannot use telephon es on a LAN. • If a power outage lasts about an hour, or the machine is disconnected f rom the power outlet for about an hour, do cuments stored in the fax machine's ...

  • Xerox C3000 - page 39

    Internet Fax Functions 29 1 Internet Fax Functions This machine conv erts scanned docu ment images to e-ma il format and transmits the data over the Internet . The e-mail sent by this machine can be received by another Internet Fa x ma- chine. Instead of dialing the telephone number of the destination you want to send to, you enter the relevant e-m ...

  • Xerox C3000 - page 40

    Transmission 30 1 Note ❒ T he In te r n e t F ax fu nct io n su p p o rt ed by th is ma ch in e i s co mp li an t w it h I TU- T Recommendation T.37. ❒ You can receive e-mail messages with an attached TIFF-F image from com- puters. ❒ Though Internet Fax documents are norm ally sent via an SMTP server, you can also send Internet Fax documents ...

  • Xerox C3000 - page 41

    Internet Fax Functions 31 1 • The level of se curity for Internet communications is low. It is recommended that you use the telephone network for confidential com munications. • Voice communication is not supported over a LAN. • Internet Fax delivery might be delayed due to netw ork congestion. Use Inter- net Fax transmission that bypasses th ...

  • Xerox C3000 - page 42

    Transmission 32 1 Functions Not Available by E-mail Reception The following functions are supp orted with standard fax reception, but not with Internet Faxing. • Memory Lock Reception • SEP Code Reception • Authorized Reception per Sender • Reception File Pr int Quantity per Sender E-mail Subject If you send e-mail without spec ifying a sub ...

  • Xerox C3000 - page 43

    Internet Fax Functions 33 1 T.37 Full Mode This machine is T.37 full mode compatible . T.37 full mode is an international standard for Internet Fax transmissi on. (ITU-T Recommendati on, RFC2532) When an Internet Fax communication is made between T.37 full mode compat- ible machines, the receiver side sends the return receipt (dispatched) in respon ...

  • Xerox C3000 - page 44

    Transmission 34 1 Placing Originals Place the original on the exposure glass or the ADF. For details about how to place originals, see the following: • Placing originals on the exposure glass “Placing Originals on the Exposure Glass”, Copy/Document Server Re fer- ence • Placing originals into the ADF “Placing Originals in the Auto Docu me ...

  • Xerox C3000 - page 45

    Placing Originals 35 1 Note ❒ To scan multiple originals using the Auto Document Feeder (ADF), set origi- nals in a stack. ❒ When sending a fax, the image output at the other end depends on the size and orientation of paper used in the receiver's machine. If the receiver does not use paper of the same size and orientation as that of the or ...

  • Xerox C3000 - page 46

    Transmission 36 1 Reference p.18 “Sending multiple origin als using the exposure glass” p.23 “Sending multiple origin als using the exposure glass” p.33 “T.37 Full Mode” p.40 “Acceptable Original Sizes” p.41 “Paper Size and Scanne d Area” p.43 “Original Sizes Difficult to De tect” p.44 “Transmission with Image Rotation” ...

  • Xerox C3000 - page 47

    Placing Originals 37 1 D Press [ OK ] . The selected original orientation appears in “Original Feed Type”. E Specify a destination, and then press the { Start } key. Reference p.221 “Storing a Document” Scanning Two-Sided Originals Use this function to send two-side d originals. The front and back of the scan ned origin al will be printed i ...

  • Xerox C3000 - page 48

    Transmission 38 1 A Place the original, and then select the scan settings you require. B Press [ Original Feed Type ] . C Specify the original orientation. Check the orientation of the placed document, and then press [] or [] . Make sure that the specified original orientation matches the orientation of originals loaded in the ADF. D Press [ 2 Side ...

  • Xerox C3000 - page 49

    Placing Originals 39 1 E Select [ Top to Top ] or [ Top to Bottom ] . F Select [ 1st Sheet ] or [ 2nd Sheet ] . To cancel two-sided transmission, press [ 1 Sided Original ] . The display returns to that of step D . Select [ 2nd Sheet ] if you want to send a cover sheet as the first page. G Press [ OK ] . “ 2 Sided Original ” appears above [ Ori ...

  • Xerox C3000 - page 50

    Transmission 40 1 Acceptable Original Sizes Note ❒ The weight range for originals in the Mi xed Original Sizes mode is 52–81 g/m 2 , 13.8–21.5 lb. Where original is set Accept able original size Maximum number of sheets Paper thickness Exposure glass Up to A3 (297 × 420 mm), 11" × 17" (279 × 432 mm) 1 ---- ADF, one-sided docu- me ...

  • Xerox C3000 - page 51

    Placing Originals 41 1 Paper Size and Scanned Area Important ❒ If you place an original larger than A3, 11" × 17" on the exposure glass, only an A3, 11" × 17" area is scanned. ❖ Exposure Glass ❖ ADF ❖ Maximum scan area The following show s the maximum scan area: • Memory Transmission: 297 × 1200 mm/11" × 47&qu ...

  • Xerox C3000 - page 52

    Transmission 42 1 Note ❒ There may be a difference in the size of the image whe n it is printed at the des- tination. ❒ Even if an original is correctly placed on the exposure glass or in the ADF, a margin of 3 mm (0.1") around each ed ge of the original may not be sent. ❒ If the receiver uses paper of a smaller width than the or iginal, ...

  • Xerox C3000 - page 53

    Placing Originals 43 1 Reference p.51 “Scan Size” Original Sizes Difficult to Detect The machine has difficulty detecting the size of the following kinds of originals. (When th is happens, the receiv ing machi ne may not select print paper of the cor- rect size.) • documents placed on the exposure glass of sizes other than those listed in the ...

  • Xerox C3000 - page 54

    Transmission 44 1 Reference “System Settings”, General Settin gs Guide Transmission with Image Rotation Generally, place A4, 8 1 / 2 " × 11" originals in the landscape orientation ( L ). If you place an A4, 8 1 / 2 " × 11" original in the po rtrait or ientation ( K ), the image is sent rotated by 90 ° . Providing the rece ...

  • Xerox C3000 - page 55

    Placing Originals 45 1 Stamp When sendin g a fax document using th e ADF, the machine can stamp a circle mark at the bott om of the origina l. When sending a two-sided document, the document is marked at th e bottom of the front pag e and top of the re ar page. Important ❒ Stamp only works when scanning from the ADF. A Place the original, and the ...

  • Xerox C3000 - page 56

    Transmission 46 1 E Specify the destination, and then press the { Start } key. Note ❒ This stamp indicates that the original has been successfully stored in mem- ory for Memory Transmission, or successfully sent by Immediate Trans- mission. ❒ When the stamp starts getting lighter, replace the cartridge. ❒ If a multi-page feed or paper jam occ ...

  • Xerox C3000 - page 57

    Scan Settings 47 1 Scan Settings You may want to se nd many diff erent ty pes of fax documents. Some of these may be difficult to reproduce at the re ceiver's end. However, the machine has three settings that you can adjus t to help you tran smit the docum ent with the best possible image quality. ❖ Scan Type: Text, Text / Line Art, Text / P ...

  • Xerox C3000 - page 58

    Transmission 48 1 A Press [ Scan Settings ] . B Make sure that [ Scan Type ] is selected. C Select the scan type you require, and then press [ OK ] . Note ❒ If you select [ Text / Line Art ] , [ Text / Photo ] , or [ Photo ] , the transmission will take longer than when [ Text ] is selected. ❒ If you send a fax document wit h [ Text / Line Art ...

  • Xerox C3000 - page 59

    Scan Settings 49 1 JBIG Transmission If you use JBIG (Jo int Bi-level Image experts Group) compression, you can send originals scanned using [ Photo ] faster than wit h other compression methods. Important ❒ This function is not available with In ternet Fax function. ❒ This function requ ires that the other party's fax machine has both th ...

  • Xerox C3000 - page 60

    Transmission 50 1 A Press [ Scan Settings ] . B Press [ Resolution ] . C Select the resolution you require, and then press [ OK ] . ...

  • Xerox C3000 - page 61

    Scan Settings 51 1 Note ❒ If you install the optional expansion me mory, “Super Fine” appears in the Resolution box. ❒ If the other party's machine does no t support the resolutio n at which you are sending, this machine au tomaticall y swit ches to a resolution that is supported. You can check the resolution at which you actually sent ...

  • Xerox C3000 - page 62

    Transmission 52 1 Auto Detect Detects the size of the fi rst page and sca ns all pages using that size. If the machine cannot dete ct the original size, a confirmation message appears. Place the original again. A Place the originals. B Press [ Scan Settings ] . C Press [ Scan Size ] . D Make sure that [ Auto Detect ] is selected. If it is not, pres ...

  • Xerox C3000 - page 63

    Scan Settings 53 1 E Press [ OK ] . “ Auto Detect: Same Size ” appears above [ Scan Settings ] . F Specify a destination and press the { Start } key. Regular The placed original is scanned accor ding to specified size regardless of actual size. The sizes that can be specified are A4 KL , B4 JIS L , A3 L , 8 1 / 2 " × 11" KL , 8 1 / 2 ...

  • Xerox C3000 - page 64

    Transmission 54 1 D Press the size of the originals to be sent. 8 1 / 2 " × 11" indicates LT. 8 1 / 2 " × 14" indicates LG. 11" × 17" indicates DLT. E Press [ OK ] . The selected size appears above [ Scan Settings ] . F Specify a destination and press the { Start } key. Note ❒ To cancel the selected scan size, sel ...

  • Xerox C3000 - page 65

    Scan Settings 55 1 C Press [ Scan Size ] . D Press [ Area 1 ] or [ Area 2 ] . E Press [ OK ] . The specified size appear s above [ Scan Settings ] . F Specify a destination and press the { Start } key. Note ❒ To cancel the selected scan size, select [ Auto Detect ] . ...

  • Xerox C3000 - page 66

    Transmission 56 1 Mixed Original Sizes Select this to individually scan the size of originals loaded into the ADF. For ex- ample, when A3 L and A4 K size originals are sent to gether, usually all are sent using the size of the first ori ginal. By selectin g Mixed Origin al Sizes, the mach ine scans and sends each original according to its size. A P ...

  • Xerox C3000 - page 67

    Scan Settings 57 1 E Press [ OK ] . “ Auto Detect: Mixed Sizes ” appears above [ Scan Settings ] . F Specify a destination and press the { Start } key. Note ❒ To cancel Mixed Original Sizes, press [ Mixed Original Si zes ] again. ❒ You can combine the origin al sizes as follows: A3 L and A4 K , B4 JIS L and B5 JIS K , A4 L and A5 K . ❒ Wh ...

  • Xerox C3000 - page 68

    Transmission 58 1 Density (Contrast) The text and diagrams on originals shou ld stand out clearly from the paper they are on. If the original has a darker ba c k g r o u n d t h a n n o r m a l ( f o r e x a m p l e , a newspaper clipping), or if the writ ing is faint, a djust the density. ❖ Auto Density The appropriate density setting for the or ...

  • Xerox C3000 - page 69

    Scan Settings 59 1 ❖ Combined Auto and Manual Density You can only adjust density for photograph s, illustrations, or diagrams if the original has a dark background. You can select on e of seven density level s. A Make sure that [ Auto Density ] is selected. B Press [ W ] or [ V ] to adjust the density. The cursor moves. Note ❒ Selecting [ Text ...

  • Xerox C3000 - page 70

    Transmission 60 1 Mixing Scan Settings for a Multiple Page Original When sending an original of several pa ges, you can select a different density, resolution, and scan type setting for each page. It is recommen ded that orig inals be placed on the expos ure glass when mixing scan settings fo r a multip le page origina l. ❖ When placing originals ...

  • Xerox C3000 - page 71

    Changing the Line Port 61 1 Changing the Line Port Select a line port or pr otocol to be used for standard f ax or IP-Fax transmissi on. When the extra G3 interface unit is in stalled, you can connect to a maximum of three ports. Important ❒ To add more fax lines, the o ptional extra G3 interface unit is required. ❖ G3 G3 is selected after powe ...

  • Xerox C3000 - page 72

    Transmission 62 1 A Press [ Select Line ] . B Select the line you want to use. If you select “G3 Auto”, the machine wi ll use any available line. This increas- es efficiency. When one opt ional extra G3 un it is instal led When two optional extra G3 units are installed When H.323/SIP are set to “On” ...

  • Xerox C3000 - page 73

    Changing the Line Port 63 1 C Press [ OK ] . The standby display appears. Note ❒ When you install the extra G3 interfac e unit, you can speci fy the line port home position. See “Regist ering a priority function using a progr am”. ❒ When sending a fax, yo u can select the line port if dialin g with the number keys. ❒ A maximum of three si ...

  • Xerox C3000 - page 74

    Transmission 64 1 Specifying a Destination This section explains how to specify a destination. Fax numbers, IP-Fax destinations, an d e-mail addresses can be specified. Note ❒ The display shows the percentage of free memo ry space for storing originals. Since fax numbers, IP-Fax dest inations and e-mail addre sses are programmed in separate memor ...

  • Xerox C3000 - page 75

    Specifying a Destination 65 1 Reference p.61 “Changing the Line Port” p.65 “Entering a pause” p.66 “Entering a tone” p.76 “Using the Address Book to Specify Destinations” p.83 “Registering Entered Destin ations to the Address Book” p.278 “Maximum Values” Entering a pause Press [ Pause ] when dialing or storing a numb er to i ...

  • Xerox C3000 - page 76

    Transmission 66 1 Entering a tone This function allows a machine connected to a pulse diali ng line to send tonal signals (for example if you want to use a special service on a tone dialing line). When you press [ Tone ] , the machine dials the number using tonal signal s. Thi s s ec ti on e xp lai ns how to us e th e t one fu nc ti on w it h On Ho ...

  • Xerox C3000 - page 77

    Specifying a Destination 67 1 Sending by IP-Fax This section ex plains how to spec ify a destination using IP-Fax transmission. When using IP-Fax transmission, specify the IP-Fax destination (IPv4 address, host name, or alias telephone numb er) in place of the fax number. Important ❒ Specify the protocol to be used in [ Select Line ] in advance. ...

  • Xerox C3000 - page 78

    Transmission 68 1 D To add a destination, press [ Add ] . When you press [ Prg. Dest. ] , you can register an ente red destination in the des- tination list. E Specify the next destination. To add another destin ation, repeat steps D and E . F Press the { Start } key. The machine starts to scan the original and stores it in memory. When scan- ning ...

  • Xerox C3000 - page 79

    Specifying a Destination 69 1 Reference p.25 “IP-Fax Functions” p.61 “Changing the Line Port” p.69 “Regarding IP-Fax destinations” p.76 “Using the Address Book to Specify Destinations” p.83 “Registering Entered Destin ations to the Address Book” p.278 “Maximum Values” “Entering Text”, About This Machine “Facsimile Feat ...

  • Xerox C3000 - page 80

    Transmission 70 1 Note ❒ To send to a G3 fax via a gateway connected to a public telephone line, you must specify the receiver's machine tele phone number. For example, if the re- ceiver's fax number is “03123456 78”, specify “5678”. To send from an IP-Fax to G3 fax without using gatek eeper or SIP server, you mus t register the ...

  • Xerox C3000 - page 81

    Specifying a Destination 71 1 A Press [ Internet Fax ] to switch the type of transmission to Internet Fax. B Specify the sender. For details about specifying se nders, see “Sender Settings”. C Press [ Manual Entry ] . D Enter the e-mail address destination, and then press [ OK ] . If you enter an incorrect character, press [ Backspace ] or [ De ...

  • Xerox C3000 - page 82

    Transmission 72 1 E To add a destination, press [ Add ] . When you press [ Prg. Dest. ] , you can register an ente red destination in the des- tination list. F Specify the next destination. To add another destin ation, repeat steps E and F . G Press the { Start } key. The machine starts to scan the original and stores it in memory. When scan- ning ...

  • Xerox C3000 - page 83

    Specifying a Destination 73 1 Reference p.29 “Internet Fax Functions” p.76 “Using the Address Book to Specify Destinations” p.101 “Sender Settings” p.114 “Canceling a Transmission” p.278 “Maximum Values” “Entering Text”, About This Machine “System Settings”, General Settings Guide “Facsimile Features”, General Se tti ...

  • Xerox C3000 - page 84

    Transmission 74 1 You can send Internet Fax document s directly to their destinations without go - ing through the SMTP server. Internet Faxes are normally transmitted via the SMTP server. Howe ver, with this feature the domain part o f the destination 's e- ma il a dd res s i s r ead as the SM TP se rv er's address and transmissions bypa ...

  • Xerox C3000 - page 85

    Specifying a Destination 75 1 C Press [ OK ] . Note ❒ When you specify destinations direct ly using the number keys, you can specify whether or not to use the SMTP server for each destination. ❒ When you sele ct de stinations in the destinatio n list, the SMTP server set- ting specified in the A ddress Book is enabled. ❒ To send Internet Fax ...

  • Xerox C3000 - page 86

    Transmission 76 1 Using the Address Book to Specify Destinations When destination s are programmed in a destination list, you can specify a des- tination by selecting a Destination key from the destination list. The programmed n ame appears on Destin ation key. Press [ Fax ] or [ Internet Fax ] to switch the transmission type between fax/IP-Fax and ...

  • Xerox C3000 - page 87

    Specifying a Destination 77 1 Note ❒ To check the contents o f Destination keys, print the dest ination list. Reference “System Settings”, General Settings Guide “Registering Addresses and Users fo r Facsimile/Scanner Functions”, Gen- eral Settings Guide Switching the titles in the Address Book There are three types of titles for destinat ...

  • Xerox C3000 - page 88

    Transmission 78 1 Specifying Group Destinations If you program multiple destinations into a Group, you can send documents to all destinations in that Group using just a few keystrokes. Destina tions pro- grammed in a group are indicated by . Important ❒ In the destination list, program an indi vidual fax number, IP-Fax destination, e-mail address ...

  • Xerox C3000 - page 89

    Specifying a Destination 79 1 Note ❒ Destinations programmed in groups can be checked using “Print Group Dial List” in “System Settings”. ❒ If a destination where a fax number, e-mail addres s, or IP-Fax destination is not programmed is included in the specified group, the confirmation message appears. Press [ Select ] to specify destin ...

  • Xerox C3000 - page 90

    Transmission 80 1 A Place the original, and then select the scan settings you require. B Press [ Recent ] . C Select the destination you want to redial to, and then press [ OK ] . D Press the { Start } key. Note ❒ You can select Internet Fax and IP-Fax destinations from Recent Destina- tions as well. ❒ When you press [ Program Dest. ] , you can ...

  • Xerox C3000 - page 91

    Programming Destinations in the Address Book 81 1 Programming Destinations in the Address Book You can program fax numbers, e-mail addresses, IP-Fax destinations, and folder destinations using Address Book Manage ment in Administrator Tools in the System Settings menu. A Press the { User Tools/Counter } key. B Press [ System Settings ] . C Press [ ...

  • Xerox C3000 - page 92

    Transmission 82 1 Note ❒ You can also re gister programme d fa x numbers, e-mail addresses, IP-Fax destinations, and fo lder destinations in a Group. ❒ When you press the { Facsimile } key to show the facsimile initial display af- ter changing t he contents of the Address Book , the “ Destination list / machine settings are updated. ” messa ...

  • Xerox C3000 - page 93

    Programming Destinations in the Address Book 83 1 Registering Entered Destinations to the Address Book This section explains how to register a directly entered fa x number, e-mail ad- dress, or IP-Fax destinat ion to the Address Book. When registering a destination directly entered or displayed on th e Recent Des- tination screen in the Address Boo ...

  • Xerox C3000 - page 94

    Transmission 84 1 Searching for a Destination in the Address Book Use this function to search for a destin ation registered in the destination list or on the LDAP server. Important ❒ To search for a destinatio n from an LDAP server, the LDAP server must be registered in advance. For details abou t registering LDAP servers, see “Sys- tem Setting ...

  • Xerox C3000 - page 95

    Searching for a Destination in the Address Book 85 1 Search by Destination Name Follow these steps to search for a destination register ed in the Address Book by name. A Press [ Search Dest. ] . B Select a search destination. To search thro ugh the Address Book, select [ Address Book ] . To search through an LDAP server, select the relevant LDAP se ...

  • Xerox C3000 - page 96

    Transmission 86 1 D Press [ Name ] . E Enter the destination name you want to search for, and then press [ OK ] . If you enter a wrong destination name, press [ ← ] , [ → ] , [ Backspac e ] , and [ Delete All ] , and then enter the destination name again. F Confirm the characters you entered, and then press [ Start Search ] . A search-in-progre ...

  • Xerox C3000 - page 97

    Searching for a Destination in the Address Book 87 1 G Select a destination. If the desired destinatio n does not appear, use [ U ] or [ T ] to scroll through the list. Press [ Details ] to display the detailed informat ion of the selected destination. Reference “Entering Text”, About This Machine Search by Fax Number/IP-Fax Destination Follow ...

  • Xerox C3000 - page 98

    Transmission 88 1 B Select a search destination. To search thro ugh the Address Book, select [ Address Book ] . To search through an LDAP server, select the relevant LDAP server. C Press [ Fax Destination ] . D Enter the number you want to search for, and then press [ OK ] . To search for an IP-Fax destination, en ter the IP-Fax desti nation that y ...

  • Xerox C3000 - page 99

    Searching for a Destination in the Address Book 89 1 E Confirm the entered fax numbers, and then press [ Start Search ] . A search-in-progress message appears. When the search is finished, a result appears. F Select a destination. If the desired destinatio n does not appear, use [ U ] or [ T ] to scroll through the list. Press [ Details ] to displa ...

  • Xerox C3000 - page 100

    Transmission 90 1 Search by E-mail Address Follow these steps to use an e-mail addres s to search for a destination registered in the destin ation list . A Press [ Search Dest. ] . B Select a search destination. To search thro ugh the Address Book, select [ Address Book ] . To search through an LDAP server, select the relevant LDAP server. C Press ...

  • Xerox C3000 - page 101

    Searching for a Destination in the Address Book 91 1 D Press [ E-mail Address ] . E Enter the e-mail address you want to search for, and then press [ OK ] . If you enter a wrong e-mail address, press [ ← ] , [ → ] , [ Backspace ] , or [ Delete A ll ] , and then enter the e-mail address aga in. F Confirm the entered characters, and then press [ ...

  • Xerox C3000 - page 102

    Transmission 92 1 G Select a destination. If the desired destinatio n does not appear, use [ U ] or [ T ] to scroll through the list. Press [ Details ] to display the detailed informat ion of the selected destination. Search Using Advanced Search Follow these steps to search for a destination register ed in the Address Book by specifying search cri ...

  • Xerox C3000 - page 103

    Searching for a Destination in the Address Book 93 1 C Press [ Advanced Search ] . D Press the key for each condition, and then enter a partial string. The following conditions can be specif ied for Address Book searches: Name, User Code, Fax Destination, E- mail Address, and Folder Name. The following conditions can be specif ied for LDAP server s ...

  • Xerox C3000 - page 104

    Transmission 94 1 E Select search criteria for each condition. The meanings of the search criteria are as follows: • [ Beginning Word ] : Search for strings that star t with the specified character. Example: When searching for “ABC”, enter “A”. • [ End Word ] : Search for strings that end with the specified character. Example: When sear ...

  • Xerox C3000 - page 105

    Searching for a Destination in the Address Book 95 1 Note ❒ You can add one additional search condition for LDAP servers by specify- ing the Search Options under Pro gra m / Change / Delete LDAP Server under System Settings. For detai ls abou t setting Search Op tions, see “Sys- tem Settings”, General Settings Guide. ❒ The string you enter ...

  • Xerox C3000 - page 106

    Transmission 96 1 C Enter a registration number using the number keys, and then press [ # ] . You do not need to ent er the first zeros of a registration number when the dis- play prompts you to enter five digits. If you make a mistake, press [ Clear ] , and then try again. D Press [ OK ] . The corresponding destination appears. Note ❒ If the “ ...

  • Xerox C3000 - page 107

    On Hook Dial 97 1 On Hook Dial The On Hook Dial function allows you to dial while listening to the tone from the internal spea ker. You can send a fax checking the co nnection. Important ❒ This function is not avai lable for the op tional ex tra G3 interface unit, Internet Fax and IP-Fax. A Place the original, and then select the scan settings yo ...

  • Xerox C3000 - page 108

    Transmission 98 1 D When the line is connected and you hear a high-pitched tone, press the { Start } key. The transmission starts. If you want to cancel a transmission, press the { Clear/Stop } key, and then re- move the originals. After transmission, the standby display appears. Note ❒ This function is unavailable in some countries. ❒ Press [ ...

  • Xerox C3000 - page 109

    Manual Dial 99 1 Manual Dial Pick up the option al handset or th e hand set of the external tele phone and dial . When the line is connected and you he ar a high-pitched tone, press the { Start } key to send your fax document. If, on th e other ha nd, you he ar a voice at the oth- er end, continue co nversation as normal. Important ❒ The optional ...

  • Xerox C3000 - page 110

    Transmission 100 1 Note ❒ When the operation switch is off, even if the main power switch is on, you cannot operate this machine using only the handset of the ex ternal tele- phone. You must first pr ess the operation switch to t urn on the machine. Reference p.76 “Using the Address Book to Specify Destinations” ...

  • Xerox C3000 - page 111

    Sender Settings 101 1 Sender Settings Use this function to set sender information. If the sender's e-mail address is registere d in the destinati on list, the sender can receive transmission results by e-mail. Also, if you enable the Stamp Sender Na me, the regi stered sender's name (user name) appears on the receiver's sheet, l ists ...

  • Xerox C3000 - page 112

    Transmission 102 1 D Confirm the selected sender, and then press [ OK ] . E To print the sender's name on the receiver's sheet, press [ Stamp Sender Name ] to highlight it. If you enable this function, the sender 's name (user name) appears on the re- ceiver's sheet, lists, and r eport. F To confirm the transmission result s by ...

  • Xerox C3000 - page 113

    Sender Settings 103 1 Note ❒ You can confirm transmission results by using both the E-mail TX Results function, which sends the results by e-mail, and the Communication Re- sult Report printed by the machine. You can set whether to use bo th of these together in User Parameters (switch 10, bit 6) in the Facsimile Fea- tures menu. ❒ You can use ...

  • Xerox C3000 - page 114

    Transmission 104 1 PIN Code Transmission A PIN (Personal Identification Number) Co de is a number used for identifying the sender . PIN Code Transmission uses the PABX (Private Automatic Branch eXch ange) system to prevent unauthorized users se nding faxes and to manage charges ac- cording to user. A PIN Code is added to the end of the fax number, ...

  • Xerox C3000 - page 115

    Sender Settings 105 1 D Enter the PIN Code, and then press [ OK ] . The standby display appears. If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then try aga in. E Press the { Start } key. Note ❒ For the maximum number of digits yo u can use in a PIN Code, see “Max- imum Values”. ❒ You can ente ...

  • Xerox C3000 - page 116

    Transmission 106 1 Advanced Features This section describes how to specify a destination using advanced features. Setting SUB Codes for Transmission Follow these steps to send a document with a SUB Code as a confidential trans- mission. A S U B C o d e i s a n I D c o n s i s t i n g o f n u m b e r s , q , p , and spaces. Document trans- mitted wi ...

  • Xerox C3000 - page 117

    Advanced Features 107 1 C Press [ Option Setting ] . D Press [ SUB Code Transmission ] . E Press [ OK ] twice. The standby display appears. F Enter the fax number of a destin ation or an IP-Fax destination. G Press [ Adv.Features ] . H Make sure that [ SUB Code ] is selected. I Press [ Transmission SUB Code ] . ...

  • Xerox C3000 - page 118

    Transmission 108 1 J Enter a SUB Code, and then press [ OK ] . If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then try aga in. K When a password is required, press [ Password ( SID) ] , enter the password with the number keys, and then press [ OK ] . L Press [ OK ] . M Press the { Start } key. If you ...

  • Xerox C3000 - page 119

    Advanced Features 109 1 Setting a password There are times when you may want to use an “SID” (Sender ID) when sending confidential faxes with the SUB Code function. When you use a Personal Box that has a password, enter the SID Code as the pass word. Note ❒ For the maximum number of digits fo r the SID Code, see “Maximum Values”. ❒ You ...

  • Xerox C3000 - page 120

    Transmission 110 1 B Press [ Option Setting ] . C Press [ SEP Code Reception ] . D Press [ OK ] twice. The standby display appears. E Enter the fax number of a destin ation or an IP-Fax destination. F Press [ Adv.Features ] . G Make sure that [ SEP Code ] is selected. H Press [ Reception SEP Code ] . ...

  • Xerox C3000 - page 121

    Advanced Features 111 1 I Enter a SEP Code, and then press [ OK ] . If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then try aga in. J When a password is required, press [ Password (PWD) ] , enter the password using the number keys, and then press [ OK ] . K Press [ OK ] . L Press the { Start } key. No ...

  • Xerox C3000 - page 122

    Transmission 112 1 Entering a password There are times yo u may want to u se a password wh en receiving faxes by S EP Code Reception. Note ❒ For the maximum number of digits for the PWD Code, see “Maximum Val- ues”. ❒ You can enter numbers, p , q , and spaces. ❒ You can store PWD Codes as well as na mes and fax numbers in the destina- tio ...

  • Xerox C3000 - page 123

    Advanced Features 113 1 SEP Code RX Result Report This report is printed after each SEP Co de Reception is completed and shows its result. If E-mail TX Resul ts is programmed in a Quick Operation key, you can select whether a report e-mail is sent after reception. Note ❒ You can also check the re sult of a SEP Code Reception with the Journal. ❒ ...

  • Xerox C3000 - page 124

    Transmission 114 1 Canceling a Transmission This section ex plains how to cancel a fax transmission. Important ❒ Remember that the Communi cating indicator turns off almost immediately when an Internet fax is being sent. Before the Original Is Scanned Use this procedure to cancel a tr ansmission before pressing the { Start } key. A Press the { Cl ...

  • Xerox C3000 - page 125

    Canceling a Transmission 115 1 Note ❒ Scanning may be complete d while you are performing the cancel operation. While the Original Is Being Transmitted Follow these steps to cancel a transmission while the Communicating indicator is lit. A Press the { Clear/Stop } key. You can also cancel a Memory Transmission by pressing [ Change TX / Info ] . B ...

  • Xerox C3000 - page 126

    Transmission 116 1 D Press [ OK ] . To cancel another file, repeat steps B and D . To cancel stopping transmission, press [ Cancel ] . E Press [ Exit ] . The standby display appears. Note ❒ If you cancel a document while it is being sent, th e transmission is halted as soon as you finish the cancellati on procedure. However, some pages o f the do ...

  • Xerox C3000 - page 127

    Canceling a Transmission 117 1 Before the Transmission Is Started Use this procedure to cancel a transm ission after the original is scanned. T h i s f u n c t i o n i s u s e f u l t o c a n c e l a t r a n s m i s s i o n w h e n y o u n o t i c e a m i s t a k e i n d e s - tination or with the originals after st o r i n g . T o c a n c e l M e ...

  • Xerox C3000 - page 128

    Transmission 118 1 C Select the file you want to cancel. If the desired file is not shown, pr ess [ U ] or [ T ] to find it. There are cases when a destination may no t be selected as the destination ap- pears as “ p ”, depending on the security settings. D Press [ Stop Transmission ] . E Press [ OK ] . To cancel another file, repeat steps C an ...

  • Xerox C3000 - page 129

    Canceling a Transmission 119 1 F Press [ Exit ] twice. The standby display appears. Note ❒ To cancel transmission to some destin a tions that a fax is sent t o, see “De- leting a Destination from a Simultaneous Broadcast”. ❒ If you cancel a transmission whi le the file is being sent, some pages of your file may have already been sent and is ...

  • Xerox C3000 - page 130

    Transmission 120 1 Confirming a Transmission A Press [ Change TX / Info ] . B Press [ Check / Stop Transmission File ] . C Select a file to check. If multiple destinations were specified, only the destinatio n select ed first ap- pears. If multiple destinations were specified, only the number of destinations for unsent document s appears. ...

  • Xerox C3000 - page 131

    Confirming a Transmission 121 1 D Press [ Check / Change Settings ] . E Confirm a transmission, and then press [ Exit ] . F Press [ Exit ] twice. The standby display appears. ...

  • Xerox C3000 - page 132

    Transmission 122 1 Checking the Storage Result (Memory Storage Report) This report is prin ted after an original is stored in memory. It helps you review the contents an d the destinations of stored originals. Important ❒ If you use Parallel Memory Transmissi on, the Memory Storage Report is not printed. Note ❒ You can turn th is report on and ...

  • Xerox C3000 - page 133

    123 2. Other Transmission Features This section explains the features of [ TX Mode ] , which you can use to apply trans- mission f unctions. Sending at a Specific Time (Send Later) Using this function, you can instruct th e machine to delay transmission of your fax document until a specified later time . This allows you to take advantage of off-pea ...

  • Xerox C3000 - page 134

    Other Transmission Features 124 2 D Enter the time using the number keys and select [ AM ] or [ PM ] . Then press [ OK ] . When entering numbers smaller than 10, add a zero a t the beginning. If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then try aga in. To cancel Send Later, press [ Cancel ] . The d ...

  • Xerox C3000 - page 135

    Requesting a Reception Notice 125 2 Requesting a Reception Notice You can confirm sent documents were pr operly received using e-mail or the Journal. The receiver sends back a reception notice message. Once the reception notice message is received, “OK” appears in the Result column of the Journal, allowing the originator t o verify the transmis ...

  • Xerox C3000 - page 136

    Other Transmission Features 126 2 Note ❒ If the fax is not received normally, “Error” appears in the Result column. ❒ Only the last 50 communications appear in the Journal. If you do not re- ceive a reception notice message before the last 50 communications are fin- ished, “OK” might not be printed in the Journal's Result column. T ...

  • Xerox C3000 - page 137

    Setting an E-mail Destination as a BCC 127 2 Setting an E-mail Destination as a BCC E-mail is sent to all specified destinati ons as bcc. A Place the original, and then select the scan settings you require. B Press [ TX Mode ] . C Press [ BCC Transmission ] to highlight it. D Press [ OK ] . The standby display appears. To check the settings, press ...

  • Xerox C3000 - page 138

    Other Transmission Features 128 2 Confirming Transmission Results by E-mail Use this function to confirm the transmi ssion results by sending an e-mail noti- fication to the specified destin ation. Important ❒ Register the e-mail address of the destin ation for e-mail notification in the destination list in advance. A Place the original, and then ...

  • Xerox C3000 - page 139

    Confirming Transmission Results by E-mail 129 2 D Select the destination of notification, and then press [ OK ] . If you make a mistake, before pressing [ OK ] , press [ Clear ] or press the selected Destination key again to turn the highlight off. [ E-mail TX Results ] gets highlighted and the destin ation of notification selected appears. E Press ...

  • Xerox C3000 - page 140

    Other Transmission Features 130 2 Entering the Subject Allows you to en ter a subject for the document you wa nt to send. A Place the original, and then select the scan settings you require. B Press [ TX Mode ] . C Press [ Subject ] . D Enter the subject. ...

  • Xerox C3000 - page 141

    Entering the Subject 131 2 E To enter the character strings programmed in the machine, press [ User Text ] , and then select the characte r strings you want to enter. F Press [ OK ] . The entered subject appears in the Subject fi eld. G Press [ OK ] . The standby display appears. H Specify a destination, and then press the { Start } key. Note ❒ F ...

  • Xerox C3000 - page 142

    Other Transmission Features 132 2 Reference p.32 “E-mail Subject” p.155 “Received Images” p.278 “Maximum Values” “Entering Text”, About This Machine “System Settings”, General Settings Guide “Facsimile Features”, General Se ttings Guide ...

  • Xerox C3000 - page 143

    Entering the Text 133 2 Entering the Text Allows you to enter the text to be transmitted. Important ❒ Program text string s in advanc e in “Progr am / Chan ge / Delete E -mail Me s- sage” in “System Settings”. A Place the original, and then select the scan settings you require. B Press [ TX Mode ] . C Press [ Text ] . D Select a text, and ...

  • Xerox C3000 - page 144

    Other Transmission Features 134 2 F Specify a destination, and then press the { Start } key. Note ❒ You cannot send text only without an original. ❒ You can program one of the Quick Oper ation keys with operations for thi s function. Using the Quick Operatio n key allows you to omit step B . Reference “System Settings”, General Settings Gui ...

  • Xerox C3000 - page 145

    Transmission Options 135 2 Transmission Options This section describes various functions that you can switch on and off for any particular transmission, followi ng the procedures gi ven here. Standard Message Stamp Use this functi on to stamp a standard message at the top of the first original sent. There are four types of standard mess ages: “Co ...

  • Xerox C3000 - page 146

    Other Transmission Features 136 2 E Select the standard message to be stamped, and then press [ OK ] . The selected standard message is shown above the highlighted [ Standard Message ] . F Press [ OK ] twice. G Specify the destination, and then press the { Start } key. The machine c annot stamp mu ltiple standard messages. Note ❒ You can program ...

  • Xerox C3000 - page 147

    Transmission Options 137 2 Important ❒ If you turn this function off, the scale of the orig inal is maintained and some parts of the image may be deleted when printed at the other end. A Place the original, and then select the scan settings you require. B Press [ TX Mode ] . C Select [ Option Setting ] . D Make sure that [ Auto Reduce ] is highli ...

  • Xerox C3000 - page 148

    Other Transmission Features 138 2 Label Insertion With this func tion you can have the re ceiver's name printed on the document that is received at the other end. Important ❒ To use this func tion, set Label Insertio n to [ On ] when registering fax destina- tions in the Address Book, and also set “L ab e l I n se r ti on ” to o n w h en ...

  • Xerox C3000 - page 149

    Transmission Options 139 2 D Press [ Label Insertion ] to highlight it. To cancel Label Insertion, press [ Label Insertion ] again. E Press [ OK ] twice. F Specify the destination, and then press the { Start } key. Note ❒ You can program one of the Quick Oper ation keys with operations for thi s function. Using the Q uick Operation key allows you ...

  • Xerox C3000 - page 150

    Other Transmission Features 140 2 Closed Network If you turn this function on , transmission will only take place if the destination's Closed Network Code is the same as yours. This function can stop you acciden- tally sending informatio n to the wrong place. Important ❒ You need to register a Closed Network C ode beforehand. ❒ This functi ...

  • Xerox C3000 - page 151

    Transmission Options 141 2 SUB Code Transmission Enable this function to perform SUB Code Transmission. Important ❒ This function is not ava ilable with Internet Fax. ❒ To perform SUB Code Transmission , a SUB Code must be set in [ Adv.Features ] , the Address Book, or Keystroke Progra ms in advance. Even though “SUB Code Transmission” is s ...

  • Xerox C3000 - page 152

    Other Transmission Features 142 2 Note ❒ You can program one of the Quick Oper ation keys with operations for thi s function. Using the Q uick Operation key allows you to omit step B an d step C . Reference p.106 “Setting SUB Codes for Transmission” p.268 “Programs” “Facsimile Features”, General Se ttings Guide “Registering Addresse ...

  • Xerox C3000 - page 153

    Transmission Options 143 2 D Press [ SEP Code Reception ] to highlight it. To cancel SEP Code Reception, press [ SEP Code Reception ] again. E Press [ OK ] twice. F Specify the destination, and then press the { Start } key. Note ❒ You can program one of the Quick Oper ation keys with operations for thi s function. Using the Q uick Operation key a ...

  • Xerox C3000 - page 154

    Other Transmission Features 144 2 Fax Header Print When the Fax Header is set to on, the stored name is printed on the receiver's paper. You can store two Fax Headers; “First Name” and “Second Name”. For example, if you store your department name in one and your organization name in the other, you could use the fi rst when sending inte ...

  • Xerox C3000 - page 155

    Transmission Options 145 2 Note ❒ You can program fax header name s using the Program Fax In formation function in the Facsimile Features menu. ❒ You can select whether or not dates, fax header names, file numbers, or page numbers are printed by changing their respective User Parameters (switch 18, bit 3, 2, 1, 0) in the Facsimile Features menu ...

  • Xerox C3000 - page 156

    Other Transmission Features 146 2 ...

  • Xerox C3000 - page 157

    147 3. Reception This section explains recept ion and reception functions such as printing received documents or routing received do cuments to other fax machines. Types of Reception This section ex plains differe nt ways of receivin g fax documents. Immediate Reception Each page of a fax document is printed as soon as it is received. This method i ...

  • Xerox C3000 - page 158

    Reception 148 3 Reference p.49 “Resolution” p.148 “Memory Reception” p.149 “Substitute Reception” p.163 “Printing Options” Memory Reception The machine waits until all pages of the document have been received into mem- ory before printing it. Important ❒ About one hour after the machine is tu rned off, all fax documents stored in ...

  • Xerox C3000 - page 159

    Types of Reception 149 3 Reference “Facsimile Features”, General Settings Guide “Troubleshooting When Using the Fa csimile Function”, Troubleshooting Substitute Reception Substitute Reception is used when th e machine cannot prin t any fax documents. In Substitute Reception, a received fax document is stored in memory instead of being print ...

  • Xerox C3000 - page 160

    Reception 150 3 Receiving documents unconditionally If one of the conditions in the follo wing list occurs, the mach ine rece ives all fax documents using Substitute Recept ion. Receiving documents according to parameter-specified settings If one of the conditions in the following list occurs, the machine receives only those documents that match th ...

  • Xerox C3000 - page 161

    Types of Reception 151 3 You can specify the following conditions with the User Parameters (switch 05, bit 2, 1) in the F acsimile Feature s menu. • When Own Na me or Own Fax Number is received The machine switches to Substitute Reception o nly when the sender has pr o- grammed their Own Name or Own Fax Nu mber. If the power is switched off for m ...

  • Xerox C3000 - page 162

    Reception 152 3 Reception Modes There are two ways you can set up the machine to handle incoming calls: • Manual Reception ( the optional handse t or an external telephone required) • Auto Reception You can change the reception mode on ly if a standard G3 line is used. You cannot change the reception mode wh en a lin e other than the standard G ...

  • Xerox C3000 - page 163

    Reception Modes 153 3 Switching the Reception Mode You can switch reception modes using Re cepti on Settings in the Facsimile Fea- tures menu. If you program a Quick Operation key with Switch Reception Mode, you can switch the reception mode quickly. A Press [ Switch RX Mode ] . B Select the reception mode, and then press [ OK ] . To cancel the sel ...

  • Xerox C3000 - page 164

    Reception 154 3 Receiving Internet Fax Documents You can receive e-mail documents by Internet Fax. There are two methods of receiving e-ma il: Auto E-mail Reception and Manual E-mail Reception. Important ❒ E-mail with attachments other than TIFF-F format files cannot be received. Senders receive an Error Ma il Notificati on if t heir e-mail cont ...

  • Xerox C3000 - page 165

    Receiving Internet Fax Documents 155 3 Manual E-mail Reception Follow these steps to receive a fax by acce ssing the e-ma il server manually. Important ❒ Program the Manual E-mail RX function to a Quick Operation key before- hand. A Press [ Manual E-mail RX ] . B Check the message, and then press [ Exit ] . The machine accesses the server to chec ...

  • Xerox C3000 - page 166

    Reception 156 3 1. E-mail transmitted without speci- fying a subject in “TX Mode”. 2. E-mail transmitted with a subject specified in “TX Mode”. 3. From The name (e-mail address) of the sender 4. Date The date and time of e-mail transmission 5. To The e-mail address of the recipient 6. Subject Shows the subject specified in “TX Mode” at ...

  • Xerox C3000 - page 167

    Reception Functions 157 3 Reception Functions This section ex plains useful fun c tions for receiving fax documents. Routing Received Documents This section descr ibes how to route received documents using SUB Codes. Important ❒ Documents cannot be routed to folders using this function. Routing received docum ents with SUB Code This machine can r ...

  • Xerox C3000 - page 168

    Reception 158 3 Transferring Received Documents The machine can tran sfer received documents by using SUB Codes. Originals sent with a SUB Code th at matches the SUB Code programmed as a Transfer Box are received then re layed to the programmed receiver. Important ❒ Transfer Boxes and Receiving Stations must be set up in order to t ransfer re- c ...

  • Xerox C3000 - page 169

    Reception Functions 159 3 Forwarding Received Documents This machine can forward received documents to other destinations pro- grammed in this machine. Note ❒ A fax number, Internet Fax address, IP-Fax destination, or folder address can be set as a forwarding destination. ❒ If an e-mail address is programmed as the destination, documents receiv ...

  • Xerox C3000 - page 170

    Reception 160 3 Reference p.278 “Maximum Values” “Facsimile Features”, General Settings Guide SMTP Reception Using Internet Fax You can receive a document sent by Internet Fax using SMTP reception. With SMTP reception, e-mail is received as soon as it is sent to the e-mail address set by the machine. Important ❒ Set this machine befo reha ...

  • Xerox C3000 - page 171

    Reception Functions 161 3 Routing e-mail received via SMTP E-mail received via SMTP can be routed to other fax machines. Important ❒ Before routing e-mail received via SMTP, you first must set “SMTP RX File Delivery Settings” to “On” in the Facsimile Features menu. ❒ Depending on security settings, th is function may not be available. T ...

  • Xerox C3000 - page 172

    Reception 162 3 Note ❒ If an e-mail transfer request is recei ved when the “SMTP RX File Delivery Set- tings” is “Off”, this machine responds with an error message to the SMTP server. ❒ You can make settings that limit tr ansfer to specified originators. ❒ Using this function, you ca n also send docu ments from your e-mail appl ica- t ...

  • Xerox C3000 - page 173

    Printing Options 163 3 Printing Options This section ex plains useful f unctions for prin ting receive d documents. Print Completion Beep When this function is turned on, the machi ne beeps to let you know whe n a re- ceived document is printed. Note ❒ You can alter the volume of the beep or turn it off completely using “Adjust Sound Volume” ...

  • Xerox C3000 - page 174

    Reception 164 3 Center Mark When this function is enable d, marks ar e printed halfway down the left side and at the top center of each page received. This makes it easy for you to position a hole puncher correctly whe n you file re- ceived documents. Note ❒ The Center Mar k may deviate a little from the exact center of the edge. ❒ You can enab ...

  • Xerox C3000 - page 175

    Printing Options 165 3 Two-Sided Printing You can have a received document printed on both sides of a sheet. Important ❒ To use this function, all pages of the received document must be of the same size-inform the sending part y of this beforehand if necessary. You must also h a v e p a p e r s e t i n t h e m a c h i n e o f t h e s a m e s i z ...

  • Xerox C3000 - page 176

    Reception 166 3 Note ❒ You can turn this function on or off using 2 Sided Print in the Facsimile Fea- tures menu. ❒ Printouts may vary depending on h ow the sender sets the originals. ❒ You can select to have documents only from selected senders printed in this way. ❒ Stored documents of the sa me size are printed on the same paper. Some st ...

  • Xerox C3000 - page 177

    Printing Options 167 3 Note ❒ The maximum number of copies that ca n be made for each document is 10. ❒ When using the Multi-copy function with specified senders, the maximum number of copies is 10. ❒ You can turn th is function on or o ff us ing Reception File Pr int Qu antity in the Facsimile Features menu. ❒ The machine will use Memory R ...

  • Xerox C3000 - page 178

    Reception 168 3 Page Separation and Length Reduction If the size of a received docume nt is lo nger than the paper loaded in the machine, each page of the document can be split and printed on severa l sheets , or reduced and printed on a single sheet. For example, this function splits the document if the document length is 20 mm (0.79") or lon ...

  • Xerox C3000 - page 179

    Printing Options 169 3 Page Reduction If you receive a document th at is longer than the pape r in the tray, the machine usually prints it on two pages. If you turn this function on, the machine reduces th e width and length of the re- ceived image so that it wi ll fit on one page. If A4 L paper is loaded and a docu- m e n t o f B 4 J I S L size is ...

  • Xerox C3000 - page 180

    Reception 170 3 If There Is No Paper of the Correct Size If there is no paper in the machine that matches the size of a received document, the machine wi ll choose a paper size based on the paper available. Note ❒ The document is split over two sheets of paper depending on the paper size. ❒ Paper placed in the bypass tray is not usually selecte ...

  • Xerox C3000 - page 181

    Printing Options 171 3 Just size printing If you enable this function, received do cuments are printed on the sheet that has the highest priority . This function is enabled with User Parameter s (switch 05, bit 5) in the Facsimile Features menu. If the paper tray is not stocked with pape r of a suitable size to print a received document, a message ...

  • Xerox C3000 - page 182

    Reception 172 3 Note ❒ You can load a maximum of 100 sheets of standard paper in the bypa ss tray. ❒ You can use a size of paper not loaded in the paper tray(s) in the bypass tray. ❒ The machine can detect A6 L , A5 L , A4 L , A3 L (5 1 / 2 " × 8 1 / 2 " L , 8 1 / 2 " × 11" L , 11" × 17" L ) paper sizes. When ...

  • Xerox C3000 - page 183

    Printing Options 173 3 Tray Shift Use this function to shift the output position for each document, so you can sep- arate received documents easily. Important ❒ The optional finisher or shift sort tr ay unit is required. When the optional finisher unit is selected for fax output, you can use the Tray Shift function wheneve r a fax or report is pr ...

  • Xerox C3000 - page 184

    Reception 174 3 ...

  • Xerox C3000 - page 185

    175 4. Changing/Confirming Communication Information This section explains the features of [ Change TX / Info ] , which you can use to con- firm communication results on the screen or printed reports. Changing the Settings of Files in Memory After you have pressed the { Start } key (after scanning original s), you can check and edit the destination ...

  • Xerox C3000 - page 186

    Changing/Confirming Communication Information 176 4 Deleting a Destination from a Simultaneous Broadcast You can delete selected br oadcasting destinations. Important ❒ If you delete a destination that is the only destinat ion for a transmission, the transmission is canceled. A Press [ Change TX / Info ] . B Press [ Check / Stop Transmission File ...

  • Xerox C3000 - page 187

    Changing the Settings of Files in Memory 177 4 D Press [ Check / Change Settings ] . E Press [ Change ] for the destination you want to delete. F Press the { Clear/Stop } key to delete the destination, and then press [ OK ] . Pressing the { Clear/Stop } key deletes by single digi ts the fax number or IP-Fax address. The Internet Fax address can be ...

  • Xerox C3000 - page 188

    Changing/Confirming Communication Information 178 4 Adding a Destination You can add a destination for broadcasting. A Press [ Change TX / Info ] . B Press [ Check / Stop Transmission File ] . C Select the file to which you want to add a destination. ...

  • Xerox C3000 - page 189

    Changing the Settings of Files in Memory 179 4 D Press [ Check / Change Settings ] . E Press [ Add Destination ] . F Specify the destination using the num ber keys or Destination keys, and then press [ OK ] . When the file has some Internet Fax de stinations, you can switch the transmis- sion type between fax/IP-Fax and Internet Fax by pressing [ F ...

  • Xerox C3000 - page 190

    Changing/Confirming Communication Information 180 4 Changing the Transmission Time You can change the transmission time specif ied with Send Later. You can also delete the transmi ssion time. If the transmission time is deleted, the file is transmitted immediately. A Press [ Change TX / Info ] . B Press [ Check / Stop Transmission File ] . C Select ...

  • Xerox C3000 - page 191

    Changing the Settings of Files in Memory 181 4 D Press [ Check / Change Settings ] . E Press [ Change TX Time ] . F Press [ Clear ] , re-enter the transmission time using the number keys, and then press [ OK ] . If you press [ Transmit Now ] , the file is transmitted immediately. However, if there is a file on standby, that file is sent first. G Pr ...

  • Xerox C3000 - page 192

    Changing/Confirming Communication Information 182 4 Changing the SMTP Server Setting You can change the settings for wh ethe r or not to bypass the SMTP server. A Press [ Change TX / Info ] . B Press [ Check / Stop Transmission File ] . C Select a file whose SMTP server setting you want to change. ...

  • Xerox C3000 - page 193

    Changing the Settings of Files in Memory 183 4 D Press [ Check / Change Settings ] . E Press [ Change ] . F Press [ SMTP ] . G Select [ Yes ] or [ No ] , and then press [ OK ] . ...

  • Xerox C3000 - page 194

    Changing/Confirming Communication Information 184 4 H Press [ OK ] . I Press [ Exit ] . Repeat from step C to change the SMTP server settings of other recipients. J Press [ Exit ] twice. The standby display appears. ...

  • Xerox C3000 - page 195

    Printing a File from Memory 185 4 Printing a File from Memory I f yo u w an t t o c h e c k th e c on t e n t s o f a fi le th a t i s s to re d i n m em o r y a nd no t y et sent, use this procedure to print it out. A Press [ Change TX / Info ] . B Press [ Check / Stop Transmission File ] . C Select the file you want to print. If multiple destinat ...

  • Xerox C3000 - page 196

    Changing/Confirming Communication Information 186 4 D Press [ Print ] . If you want two-sided printing, press [ Print on 2 Sides ] . To cancel printing, press [ Cancel ] . The display returns to that of step C . E Press the { Start } key. To cancel printing after pressing the { Start } key, press [ Stop Printing ] . The dis- play returns to that of ...

  • Xerox C3000 - page 197

    Printing a List of Files in Memory (Print TX File List) 187 4 Printing a List of Files in Memory (Print TX File List) Print this list if you want to find out which fil es are stored in memory and what their file numbers are. Knowing the f ile number can be useful (for example when erasing files). A Press [ Change TX / Info ] . B Press [ Check / Sto ...

  • Xerox C3000 - page 198

    Changing/Confirming Communication Information 188 4 D Press the { Start } key. To cancel printing after pressing the { Start } key, press [ Stop Printing ] . The dis- play returns to that of st ep C . E Press [ Exit ] twice. The standby display appears. Note ❒ The contents of a file stored in memory can also be printed. ❒ You can set whether or ...

  • Xerox C3000 - page 199

    Resending a File 189 4 Resending a File Machine memory stores documents that could not be successfully transmitted using Memory Transmission. Use this procedure to resend these documents. Important ❒ Set “Store documents in memory that could not be tra nsmitted” to “On” in User Parameters (switch 24, bit 0) in the Facsi mile Features menu ...

  • Xerox C3000 - page 200

    Changing/Confirming Communication Information 190 4 D Press [ Transmit Failed File ] . To add a destination, press [ Add Destination ] , and then specify the destination. E Press [ OK ] . Repeat from step C to resend another file. To cancel transmissions, press [ Cancel ] . The display re turns to that of step D . F Press [ Exit ] twice. The standb ...

  • Xerox C3000 - page 201

    Checking the Transmission Result (Transmission File Status) 191 4 Checking the Transmission Result (Transmission File Status) You can confirm transmission by the display, report, or e-mail. Confirming on Display Follow these steps to displa y the transmi ssion results. A Press [ Change TX / Info ] . B Select [ Transmission File Status ] . C Check t ...

  • Xerox C3000 - page 202

    Changing/Confirming Communication Information 192 4 Note ❒ Only the transmission results of the latest communications are displayed. For the maximum number of communica tion result s you can check on this machine, see “Maximum Values”. ❒ You can view sent fax documents and their lists, using a Web Image Moni- tor on a network computer. For ...

  • Xerox C3000 - page 203

    Checking the Transmission Result (Transmission File Status) 193 4 Confirming by E-mail Use the E-mail TX Results function to se nd reports by e-mail to a computer, and then confirm them on t he computer. The available reports are: • Communication Result Report. • Immediate TX Result Report. • Polling with SEP Rx Result. Important ❒ You must ...

  • Xerox C3000 - page 204

    Changing/Confirming Communication Information 194 4 Communication Result Report (Memory Transmission) This report is printed when a Memory Transmission is completed, so you can check the result of the transmission. Note ❒ If E-mail TX Results is programmed in a Quick Operation key, you can select whether a report e-mail is sent after tr ansmissio ...

  • Xerox C3000 - page 205

    Checking the Transmission Result (Transmission File Status) 195 4 Note ❒ If E-mail TX Results is programmed in a Quick Operation key, you can select whether a report e-mail is sent after tr ansmission. ❒ You can switch this report on or off in the User P arameters (switch 03, bit 5) in the Facsimile Features menu. ❒ To view the report without ...

  • Xerox C3000 - page 206

    Changing/Confirming Communication Information 196 4 Checking the Reception Result (Reception File Status) Confirm the reception result on the screen or i n a report. Confirming on Display Follow these steps to display the reception result. A Press [ Change TX / Info ] . B Press [ Reception File Status ] . C Check the reception results. Reception re ...

  • Xerox C3000 - page 207

    Checking the Reception Result (Reception File Status) 197 4 Note ❒ Only the reception results of the late st communications are displayed. For the maximum number of communication results you can check on this ma- chine, see “Maximum Values”. ❒ You can view received fax documents and their lists, using a Web Im age Monitor on a network compu ...

  • Xerox C3000 - page 208

    Changing/Confirming Communication Information 198 4 Print Journal You can print the Journal manually. Important ❒ The contents of a Journal printed auto matically are deleted after printing. Keep the journal if you require a reco rd of transmissions and receptions. Printing the Journal To print the Journal manually, select th e printing method: ? ...

  • Xerox C3000 - page 209

    Print Journal 199 4 All Prints the results of communications in the order made. A Press [ Change TX / Info ] . B Press [ Print Journal ] . C Select [ All ] . D Press the { Start } key. To cancel a file printing, press [ Stop Printing ] . The display returns to that of step C . E Press [ Exit ] twice. The standby display appears. ...

  • Xerox C3000 - page 210

    Changing/Confirming Communication Information 200 4 Print per File No. Prints only the results of communic ations specified by file number. A Press [ Change TX / Info ] . B Press [ Print Journal ] . C Select [ Print per File No. ] . D Enter a 4-digit file number. If you make a mistake, press [ Clear ] or the { Clear/S top } key, and then try again. ...

  • Xerox C3000 - page 211

    Print Journal 201 4 Print per User Prints the results of communica tions by individual senders. A Press [ Change TX / Info ] . B Press [ Print Journal ] . C Select [ Print per User ] . D Select a user. Press [ Cancel ] if the user is not registered. The display returns to that of step C . E Press [ OK ] after checking the user name shown on the dis ...

  • Xerox C3000 - page 212

    Changing/Confirming Communication Information 202 4 F Press the { Start } key. To cancel a file printing, press [ Stop Printing ] . The display returns to that of step C . G Press [ Exit ] twice. The standby display appears. ...

  • Xerox C3000 - page 213

    Print Journal 203 4 Journal This section e xplains the i t ems printed in the Journal. 1. Printing date Shows the date and time the report was printed. 2. Programmed Fax Header Shows the sender name programmed for printing. 3. Date Shows the transmission or reception date. 4. Time Shows the transmission or reception start time. 5. Other end • F o ...

  • Xerox C3000 - page 214

    Changing/Confirming Communication Information 204 4 • For Internet Fax dest inations At time of transmission, it shows the e-mail address or name programmed in the destination list. At time of re- ception, it shows the e-mail address of the sender. At time of broadcasting transmission, it shows the number of destinations after the e-mail addresse ...

  • Xerox C3000 - page 215

    Print Journal 205 4 Transmitting Journal by E-mail Use this function to send the Journal to the administrator's e-mail address. The Journal is sent automatically after every 50 communicati ons. A CSV format Journal is attached t o the e-mail. Important ❒ To transmit the Journal by e-mail, it is n e c es s a ry t o m a k e s e t t i n g s w i ...

  • Xerox C3000 - page 216

    Changing/Confirming Communication Information 206 4 Printing/Deleting Received and Stored Documents (Print/Delete Stored Reception File) You can print documents that are received and stored on the hard disk. You can also delete unwanted documents. Important ❒ Make the settings for received and stor ed documents in “Reception File Set- ting” i ...

  • Xerox C3000 - page 217

    Printing/Deleting Received and Stored Documents (Print/Delete Stored Reception File) 207 4 Printing Received and Stored Documents Use the following procedure to print documents saved on the hard disk. A Press [ Change TX / Info ] . B Press [ Print / Delete Stored Reception File ] . C Select a file to be printed, and then press [ Print ] . To cancel ...

  • Xerox C3000 - page 218

    Changing/Confirming Communication Information 208 4 Reference p.278 “Maximum Values” “Facsimile Features”, General Se ttings Guide Deleting Received and Stored Documents Use the following procedure to delete docume nts stored on the hard disk. A Press [ Change TX / Info ] . B Press [ Print / Delete Stored Reception File ] . C Select a file ...

  • Xerox C3000 - page 219

    Printing a File Received with Memory Lock 209 4 Printing a File Received with Memory Lock This is a security function de signed to prevent un authorized user s from reading your documents. If Memory Lock Recept ion is switched on, all received docu- ments are stored in memory and are not automatical ly printed. To print t he doc- uments, you have t ...

  • Xerox C3000 - page 220

    Changing/Confirming Communication Information 210 4 D Enter a 4-digit Memory Lock ID with the number keys, and then press the { Start } key. I f t h e M e m o r y L o c k I D d o e s n o t m a t c h , t h e “ Specified c ode does not correspond to programmed Memory Lock ID. ” message appears. Press [ Exit ] and retry after checking the Memory L ...

  • Xerox C3000 - page 221

    Personal Boxes 211 4 Personal Boxes You can receive confidential documents in Personal Boxes. Important ❒ Before using this function, set the Personal Bo x in advance. Personal Boxes Storing your docu ments in a Personal Bo x prevents unauthorized users reading them. When you sp ecify a receiver fo r the Pers onal Box, incoming documents are for- ...

  • Xerox C3000 - page 222

    Changing/Confirming Communication Information 212 4 Printing Personal Box Documents Follow these steps to print a docume nt received into a Personal Box. A Make sure that the Confidential File indicator is lit. B Press [ Change TX / Info ] . C Press [ Print Personal Box File ] . D Select the box with the document you want to print. AL V017S ...

  • Xerox C3000 - page 223

    Personal Boxes 213 4 E If a password has been set for the bo x, enter the password, and then press [ OK ] . If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then try aga in. To cancel entering a password, press [ Cancel ] . The display returns to that of step D . F Press the { Start } key. To stop print ...

  • Xerox C3000 - page 224

    Changing/Confirming Communication Information 214 4 Information Boxes This section descr ibes how to use I nformation Boxe s. Important ❒ Before using this function, set th e Information Box in advance. Information Boxes Use the Information Box function to set up the machine as a document server. Program a document into an Information Box for oth ...

  • Xerox C3000 - page 225

    Information Boxes 215 4 Storing Documents in Information Boxes Follow these steps to store a do cument in an Information Box. A Press [ Change TX / Info ] . B Press [ Store / Delete / Print Information Box File ] . C Select the box in which you want to store the file. When ther e are pre-programmed files, a file mark appears to the left of the box ...

  • Xerox C3000 - page 226

    Changing/Confirming Communication Information 216 4 E Place the original, and then select the scan settings you require. You can also select the following settings: • Original Orientation • Original Se ttings •S t a m p F Press the { Start } key. The machine starts to scan the original. To stop scanning, press [ Stop ] . The display return s ...

  • Xerox C3000 - page 227

    Information Boxes 217 4 Printing Information Box Documents Follow these steps to print a document stored in an Information Box. A Press [ Change TX / Info ] . B Press [ Store / Delete / Print Information Box File ] . C Press [ Print ] . D Select the box that contains the stored file you want to print. You cannot select a box that has no stored file ...

  • Xerox C3000 - page 228

    Changing/Confirming Communication Information 218 4 F Press the { Start } key. If you want two-si ded printing, press [ Print on 2 Sides ] before pressing the { Start } key. To stop printing before pressing the { Start } key, press [ Cancel ] . The display re- turns to that of step D . To stop printing after pressing the { Start } key, press [ Stop ...

  • Xerox C3000 - page 229

    Information Boxes 219 4 E If a password has been set for the bo x, enter the password, and then press [ OK ] . If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then try aga in. To cancel entering a password, press [ Cancel ] . The display returns to that of step D . F Press [ Yes ] . To stop deleting, p ...

  • Xerox C3000 - page 230

    Changing/Confirming Communication Information 220 4 ...

  • Xerox C3000 - page 231

    221 5. Storing a Document This section explains stor ing and managing documents in the Document Server. Sending a Stored File This section describes how to store and manage fax docume nts in the Document Server. The Document Server can store docu ments from various applications. The documents that are stored using the fa csimile function are availa ...

  • Xerox C3000 - page 232

    Storing a Document 222 5 Note ❒ Stored documents are not deleted even if there is a power failure, or the main power switch is turned off. ❒ You can specify whether or not the ma chine automatically deletes documents from the Document Server after a certai n number of days. The delete function is preconfigured with the software an d automatical ...

  • Xerox C3000 - page 233

    Sending a Stored File 223 5 A Place the original, and then select the scan settings you require. Set “Original Orientation” correctly. If you do not, the top/bo ttom orienta- tion of the original will not be displayed correctly in the preview. B Press [ Store File ] . C Select [ Send & Store ] or [ Store Only ] . Select [ Send & Store ] ...

  • Xerox C3000 - page 234

    Storing a Document 224 5 F If you have selected [ Send & Store ] , specify the receiver. If you have selected [ Store Only ] , proceed to step G . G Press the { Start } key. Note ❒ You can change file names and user names. Reference p.36 “Setting the Original Orientation” “System Settings”, General Settings Guide Programming a user na ...

  • Xerox C3000 - page 235

    Sending a Stored File 225 5 Reference “Entering Text”, About This Machine Setting a file name A Press [ File Name ] . B Enter the file name. C Press [ OK ] . Reference “Entering Text”, About This Machine Setting a password A Press [ Password ] . ...

  • Xerox C3000 - page 236

    Storing a Document 226 5 B Enter a password using the number keys, and then press [ OK ] . If you make a mistake, press [ Clea r ] or the { Clear/Stop } key before pressing [ OK ] , and then reent er your password. You can enter up to four to eight digits. C Enter the password again, and then press [ OK ] . Sending Stored Documents The machine send ...

  • Xerox C3000 - page 237

    Sending a Stored File 227 5 B Select the documents to be sent. When multiple documents are selected, th ey are sent in the order of selection. •P r e s s [ Queue ] to arrange the order of the documents to be sent. •P r e s s [ File Name ] to place the documents in alphabetical order. •P r e s s [ User Name ] to place the documents in order by ...

  • Xerox C3000 - page 238

    Storing a Document 228 5 D When you want to add your original s to stored documents and send them all at once, press [ Original n Stored File ] or [ Stored file n Original ] . When sending only stored documents, proceed to step E . When [ Original n Stored File ] is pressed, the machine sends the originals, and then stored files. When [ Stored file ...

  • Xerox C3000 - page 239

    Sending a Stored File 229 5 Specifying documents from [ File List ] A Press [ U ] or [ T ] to display the documents to be sent. B Select the fi le. Specifying documents by [ User Name ] A Select [ User Name ] . B Select the user name of the prog rammed document, and then press [ OK ] . T o s e a r c h b y d i r e c t l y e n t e r i n g a u s e r n ...

  • Xerox C3000 - page 240

    Storing a Document 230 5 Specifying documents by [ File Name ] A Select [ File Name ] . B Enter the name of the document to be sent, and then press [ OK ] . Partial matching is used when searching for a file name. C Select the file to be sent. Displaying a preview A Select the document you want to send. Press the Thumbnail key to switch the screen ...

  • Xerox C3000 - page 241

    Sending a Stored File 231 5 C Check the preview. •P r e s s [ Zoom Out ] or [ Zoom In ] to reduce or enlarge the preview image. •P r e s s [ ← ][ → ][ ↑ ][ ↓ ] to scroll the preview image. •P r e s s [ Switch ] for “Display File” to disp lay another se lected file . •P r e s s [ Switch ] for “Display Page” to change the disp ...

  • Xerox C3000 - page 242

    Storing a Document 232 5 B Select the document to be printed. Press the Thumbnail key to switch the screen to thumbnail display. C If you select a document with a password, enter the password, and then press [ OK ] . If the document does not have a password, proceed to step D . D Press [ Print File ] or [ Print 1st Page ] . When [ Print File ] is p ...

  • Xerox C3000 - page 243

    Sending a Stored File 233 5 Note ❒ Only documents stored using the fa csimile function can be printed. ❒ When printing originals th at were not stored using the Mi xed Original Siz- es function, paper sizes might differ according to whether printing is through the facsimil e function or the Document Server. ❒ You can also print the fi rst pag ...

  • Xerox C3000 - page 244

    Storing a Document 234 5 C If you select a document for which a password is set, enter the password, and then press [ OK ] . When a selected file does not ha ve a password, proceed to step D . D Change the desired informatio n of the stored document. Press the keys for the it ems you want to change. E Press [ Exit ] . The standby display appears. ...

  • Xerox C3000 - page 245

    Sending a Stored File 235 5 Changing a user name A Press [ Change User Name ] . B Press [ Clear ] . The user name is deleted. C Enter the new user name, and then press [ OK ] . Press the title word keys to switch between titles. To set a non-programmed user name, press [ Manual Entry ] , and then enter the name. User names entered by pressing [ Man ...

  • Xerox C3000 - page 246

    Storing a Document 236 5 Changing the file name A Press [ Change File Name ] . B Press [ Backspace ] or [ Delete All ] , and then re-enter the file name. C Press [ OK ] . Reference “Entering Text” About This Machine Changing the password A Press [ Change Password ] . ...

  • Xerox C3000 - page 247

    Sending a Stored File 237 5 B Enter a new password using the number keys, and then press [ OK ] . C Enter the password again, and then press [ OK ] . Deleting a Stored Document Use this function to delete stored documents. A Press [ Select Stored File ] . ...

  • Xerox C3000 - page 248

    Storing a Document 238 5 B Press [ Manage / Delete File ] . C Select the document you want to delete. You can also de lete multiple documents at on ce. D Enter a password using the number keys, and then press [ OK ] . E Press [ Delete File ] . F Press [ Yes ] . If you do not want to delete the document, press [ No ] . G Press [ Exit ] . The standby ...

  • Xerox C3000 - page 249

    239 6. Fax via Computer This section expla ins how to use this machine's facsimil e function from a com- puter via a network. Sending Fax Documents from Computers You can send a document created with a Windows application from a computer connected to the machine to another fax m achine. Connect computers to the machine via pa rallel port, LAN, ...

  • Xerox C3000 - page 250

    Fax via Computer 240 6 Note ❒ It is recommended that you use W eb Image Monitor running under th e same network environment as this machine. Otherwise, the Web browser may not open and an e rror may occur. Before Use To use these features, a LAN-Fax Driver must be installed on your computer. Use the LAN-Fax Driver included on th e scanner CD-ROM. ...

  • Xerox C3000 - page 251

    Sending Fax Documents from Computers 241 6 ❖ Operating environment •C o m p u t e r PC/AT compatible • Operating systems Microsoft Windows 98/Me Microsoft Windows 2000/XP Microsoft Windows Server 2003 Microsoft Windows NT 4.0 •D i s p l a y VGA 640 × 480 pixels or more Note ❒ Before beginning installation, exit all other appl ications. A ...

  • Xerox C3000 - page 252

    Fax via Computer 242 6 Auto Run program The installers for vari ous drivers and utili ties launch automati cally as Auto Run programs when you insert the CD-ROM. LAN-Fax Driver, A ddress Book, and LA N-Fax Cover Sheet Editor can be in- stalled by Auto Run. Important ❒ If the plug and play function starts, click [ Cancel ] in the [ New Hardware Fo ...

  • Xerox C3000 - page 253

    Sending Fax Documents from Computers 243 6 A Quit all applications currently running. B Insert the CD-ROM included with this machine into the CD-ROM drive of your computer. The installer launches automatically, and the language selection window ap- pears. Depending on your operating system settings, the installer may not launch automatically. If it ...

  • Xerox C3000 - page 254

    Fax via Computer 244 6 Setting print properties This section ex plains how to mak e settin gs such as paper size or resolution. A On the [ Start ] menu, point to [ Settings ] , and then click [ Printers ] . With Windows XP Profe ssional or Windows Server 2003, select [ Printers and Faxes ] on the [ Start ] menu. With Windows XP Ho me Edition, selec ...

  • Xerox C3000 - page 255

    Sending Fax Documents from Computers 245 6 Making settings for opt ion configuration Make settings for optional unit s installed in this machine. A On the [ Start ] menu, point to [ Settings ] , and then click [ Printers ] . With Windows XP Profe ssional or Windows Server 2003, select [ Printers and Faxes ] on the [ Start ] menu. With Windows XP Ho ...

  • Xerox C3000 - page 256

    Fax via Computer 246 6 Basic Transmission This section explains how to send fa x documents created using Windows appli- cations. To send a fax, simply select [ Print... ] from the Window s application, t hen select [ LAN-Fax M8 ] as the printer, and then specify a de stination in the [ LAN-Fax ] dialog box. Open the application docu ment you want t ...

  • Xerox C3000 - page 257

    Sending Fax Documents from Computers 247 6 Reference p.247 “Specifying a destination using a destination list” p.247 “Specifying a destination using Address Book” p.248 “Specifying a destination by dire ctly entering a fax number, Int ernet Fax Destination, or IP-Fax destination” p.249 “Specifying Options” p.252 “Confirming Transm ...

  • Xerox C3000 - page 258

    Fax via Computer 248 6 C Select [ Contact ] or [ Group ] in the [ Name: ] d r o p d o w n m e n u a s t h e d i s p l a y f o r m a t . Destination list conten ts change as foll ows, depending on the option selected: • Contact: Individual name, company na me, department name, fax number •G r o u p : G r o u p n a m e If you selected [ Group ] , ...

  • Xerox C3000 - page 259

    Sending Fax Documents from Computers 249 6 D Specify settings according to th e type of fax transmission. Specify settings according to the type of fax transmission selected in step B , as follows: •I f y o u s e l e c t e d [ Fax ] , select a line or a protocol in the [ Line: ] list. •I f y o u s e l e c t e d [ E-mail ] , select the [ Do not ...

  • Xerox C3000 - page 260

    Fax via Computer 250 6 To print a sender stamp A Click [ Send Options ] . The [ Send Options ] tab appears. B Select the [ Print Fax Header ] check box. To attach a cover sheet A Click [ Send Options ] . The [ Send Options ] tab appears. B Select the [ Attach a Cover Sheet ] check box. A cover sheet is added to the fi rst page of a transmission fil ...

  • Xerox C3000 - page 261

    Sending Fax Documents from Computers 251 6 Saving as files You can save the fax document in TIFF format (TIFF-F). A Click [ Send Options ] . The [ Send Options ] tab appears. B Select the [ Save as file ] check box. C Click [ Save to... ] . D Select a folder on the folder tree. E Select a method of file naming. To enter a file name manually, select ...

  • Xerox C3000 - page 262

    Fax via Computer 252 6 Checking Transmission Using LAN-Fax Driver From “SmartDeviceMonitor for Admin”, “SmartDeviceMonitor for Client”, or Web Image Monitor, yo u can check information abo ut files sent using LAN-Fax Driver. For the maximum number of tran smission results you can check, see “Maximum V alues”. Also, you can save the cont ...

  • Xerox C3000 - page 263

    Sending Fax Documents from Computers 253 6 D Click [ Send ] or [ Send & Print ] . Note ❒ You can confirm transmission results using the E-mail TX Results function and the Communication Result Report. You can set wheth er to use both of these together in User Parameters (switch 10, bit 6) in the Facsimile Fea- tures menu. ❒ If there be any i ...

  • Xerox C3000 - page 264

    Fax via Computer 254 6 Printing and Saving You can print documents create d using Windows applicat ions. Open the applicatio n docume nt you want to print or create a new document, and then perform the f ollowing procedure. For details about printing the fax im age, see the LAN-Fax Driver's Help. A On the [ File ] menu, click [ Print... ] . B ...

  • Xerox C3000 - page 265

    Sending Fax Documents from Computers 255 6 Programming new destinations A On the [ Start ] menu, point to [ Programs ] , [ LAN-Fax Utilities ] , and then click [ Ad- dress Book ] . The [ Address Book ] dialog box appears. If LAN-Fax Driver has already started up, click [ Edit Address Book... ] . B Click [ New/Browse... ] , and then select the CSV f ...

  • Xerox C3000 - page 266

    Fax via Computer 256 6 Editing programmed destinations A On the [ Start ] menu, point to [ Programs ] , [ LAN-Fax Utilities ] , and then click [ Ad- dress Book ] . The [ Address Book ] dialog box appears. If LAN-Fax Driver has already started up, click [ Edit Address Book... ] . B Click [ New/Browse... ] , and then select the CSV file containing th ...

  • Xerox C3000 - page 267

    Sending Fax Documents from Computers 257 6 G If you made changes to a destination, a confirmation message appears. To save the changes, click [ Yes ] . If you do not want to save the chan ges and want to quit editing, click [ No ] . To return to the editing display, click [ Cancel ] . The confirmation dialog box does not appear when you have not ma ...

  • Xerox C3000 - page 268

    Fax via Computer 258 6 Editing Fax Cover Sheets LAN-Fax Cover Sheet Editor allows you to edit the format for fax cover sheets. Important ❒ It is necessary to cr eate a cover sheet file before attaching a cover sheet to fax document using LAN-Fax Driver. Creating a cover sheet Use the following procedure to create a fax cover sheet. You can edit t ...

  • Xerox C3000 - page 269

    Sending Fax Documents from Computers 259 6 Attaching a created cover sheet Use the following procedure to attach a created cover sheet file to a fax docu- ment. A On the [ File ] menu, click [ Print... ] . B Select [ LAN-Fax M8 ] in the [ Name: ] list, and then click [ OK ] . The [ LAN-Fax ] dialog box appears. C Click [ Edit Cover Sheet... ] . The ...

  • Xerox C3000 - page 270

    Fax via Computer 260 6 Managing Facsimile Functions Using SmartDeviceMonitor for Admin You can check information about this ma chine's fax functions using a computer and save files on a computer usin g SmartDeviceMonit or for Admin. Note ❒ For details about SmartDeviceMon itor for Admin and its installation, see “Monitoring and Configuring ...

  • Xerox C3000 - page 271

    Viewing Fax Information Using a Web Browser 261 6 Viewing Fax Information Using a Web Browser You can view received fax documents and their lists or print these documents using a Web Image Monitor on a network computer. Note ❒ It is recommended that you use a Web Image Monitor running under the same network environment as this machine. Otherwise, ...

  • Xerox C3000 - page 272

    Fax via Computer 262 6 F View the content of the fax document. To enlarge the preview image, click [ Enlarge Image ] . Enlargement cannot be performed without Acrobat Reade r instal led. For more information, see Help on the Web Image Mo nitor. G To download the received fax document, click [ PDF ] or [ Multi-page TIFF ] , and then click [ Download ...

  • Xerox C3000 - page 273

    Viewing Fax Information Using a Web Browser 263 6 Deleting fax information using a Web browser A Start a Web browser. B Enter the machine's IPv4 address in the [ Address ] field. C Click [ Fax Received File ] in the left pane. The list of received fa x documents appears. D Select the check box of the fax document to be deleted. To view a li st ...

  • Xerox C3000 - page 274

    Fax via Computer 264 6 To edit machine properties a lready programmed Follow thes e steps to use Web Image Mon itor to edit inform ation about the des- tination machine registered in the Address Book. A Start the Web browser. B Enter the IPv4 address of the machine you want to monitor after “http://” in the address field. The top screen is disp ...

  • Xerox C3000 - page 275

    Viewing Fax Information Using a Web Browser 265 6 To add new receiver Follow these steps to use Web Image Monitor to add a new destination to the Address Book. A Start the Web browser. B Enter the IPv4 address of the machine you want to monitor after “http://” in the address field. The top screen is displayed. C Click [ Login ] , and then enter ...

  • Xerox C3000 - page 276

    Fax via Computer 266 6 Delivering Files Received by Fax Documents received by the machine can be viewed on or downl oaded to a com- puter using the network deli very server Sc anRouter deli very software. This is a useful function, enabling you to view and store documents on your computer without printing them. Important ❒ The ScanRouter delivery ...

  • Xerox C3000 - page 277

    267 7. Appendix This section ex plains features an d spec ifications of the facsimile function. Checking the Memory Status Use this function to display a summary of current memory usage. On the standby display you can check the percentage of free memory space. In addition, in [ System Status ] you can check the number of “Transmission Standby Fil ...

  • Xerox C3000 - page 278

    Appendix 268 7 Programs If you regularly send documents to a part icular destination or transmit using the same functions, you can save repetitive number keys o perations by reg istering this information in a Keystroke Program. P r o g r a m s c a n b e r e c a l l e d b y j u s t p r e s s - ing a programmed key. Registering and Changing Keystroke ...

  • Xerox C3000 - page 279

    Programs 269 7 D Press [ Program ] . When no progra ms are registered , proceed to ste p E . E Select a program number in whic h “Not Programmed” is shown. If you make a mistake, press [ Cancel ] and select a program number again. When you change a Keystroke Program, press [ Yes ] after pressing the program number you want to change. If you mak ...

  • Xerox C3000 - page 280

    Appendix 270 7 Reference p.123 “Sending at a Specific Time (Send Later)” p.278 “Maximum Values” “Entering Text”, About This Machine Registering a priority function using a program Set the functions registered in a program as priority functions, so you can have the machine select these func tions right after the p ower is turned on or t ...

  • Xerox C3000 - page 281

    Programs 271 7 Changing a program name Follow these steps to change a program name. A Make sure that the machine is in facsimile mode and the standby display is shown. If the standby display is not shown, pre ss the { Facsimile } key . B Press the { Program } key. C Press [ Change Name ] . D Select the program number of the name you want to change. ...

  • Xerox C3000 - page 282

    Appendix 272 7 Deleting a Program Follow these steps to dele te an unnecessary pr ogram: A Make sure that the machine is in facsimile mode and the standby display is shown. If the standby display is not shown, pre ss the { Facsimile } key . B Press the { Program } key. C Press [ Delete ] . D Select the program number you want to delete. E Press [ Y ...

  • Xerox C3000 - page 283

    Programs 273 7 Using a Program Follow these steps to recall and use a registered program: A Make sure that the machine is in facsimile mode and the standby display is shown. If the standby display is not shown, pre ss the { Facsimile } key . B Place the original. C Press the { Program } key. D Confirm that [ Recall ] is selected, and press the regi ...

  • Xerox C3000 - page 284

    Appendix 274 7 Optional Equipment This section explains the functions of options. Expansion Memory (28MB: DIMM) This allows you to send fax do cuments at hi gh resolution (Super Fine). This also allows you to receiv e fax documents at high resolu tion (Fine or Super Fine). If you require this option, consul t your service representative. Reference ...

  • Xerox C3000 - page 285

    Specifications 275 7 Specifications ❖ Fax Transmission and Reception ❖ Power Consumption ❖ IP-Fax Transmission and Reception Standard G3 Resolution G3: 8 × 3.85/mm, 200 × 100 dpi (Standard character), 8 × 7.7/mm, 200 × 200 dpi (Detail character), 8 × 15.4/mm (Fine character: optional), 16 × 15.4/mm, 400 × 400 dpi (Super Fine character: ...

  • Xerox C3000 - page 286

    Appendix 276 7 ❖ Internet Fax Transmission and Reception *1 Full mode Compatible machines IP-F ax compatible machines IP-Fax transmission function Specify an IPv4 a ddress and send faxes to an IP-Fax compati- ble fax through a network. Also capable of sending faxes to a G3 fax connected to a tele- phone line via a VoIP gateway. IP-Fax reception f ...

  • Xerox C3000 - page 287

    Specifications 277 7 Specifications Required for th e Internet Fax Destination Machines This machine can communicat e with Internet Fax machin es that satisfy t he fol- lowing specific ation requir ements. When communicating with full mode compatible machines, you can take ad- vantage of h igher specificatio ns for coding, or iginal size, and r eso ...

  • Xerox C3000 - page 288

    Appendix 278 7 Maximum Values The following list contains th e maximum value for each item. Item Standard Expansion memory (Optional) Memory 4 MB 28 MB Number of documents you can store in memory for Memory Transmission 400 400 Number of pages you can store in memory (using A4 Standard <ITU-T q 1 Chart>) Approx. 320 Approx. 2,240 Number of de ...

  • Xerox C3000 - page 289

    Maximum Values 279 7 Note ❒ The maximum number of pa ges that can be stored or transmitted may de- crease depending on the contents of documents. Number of received documents you can store on the machine's hard disk 400 400 Number of documents you can print at a time in [ Print / Delete Stored Reception File ] 30 30 Number of documents you c ...

  • Xerox C3000 - page 290

    280 INDEX 180-degree rotation printing , 166 1st Sheet , 37 2nd Sheet , 37 2 Sided Original , 37 2 Sided Print , 9 2 sided printing , 250 A Acceptable original sizes , 40 Add , 20 Add Destination , 178 Adding a destination , 178 Address Book , 241 , 254 Add User , 265 Adjust Sound Volume , 9 Advanced Features , 106 Advanced Search , 92 Adv.Features ...

  • Xerox C3000 - page 291

    281 Communicating indicator , 115 Communication Failure Report , 195 Communication Page Count , 9 Communication Result Report , 194 Compatible machines , 277 Confidential File indica tor , 209 Confidential File Report , 213 Confirming a transmission , 120 Confirming by e-mail , 193 Confirming by report , 192 , 19 7 Confirming by report and e-mail , ...

  • Xerox C3000 - page 292

    282 H H.323 , 27 H.323 Settings , 9 Handset , 99 , 152 , 274 Having incoming documents printed on paper from the bypass tray , 171 How to Read This Manual , 4 I If there is no paper of the correct size , 170 Image Rotation , 167 Immediate Reception , 147 Immediate Transmis sion , 13 , 21 Immediate TX Result Report , 194 Important Safety Instruction ...

  • Xerox C3000 - page 293

    283 P Page reduction , 169 Page separation and length reduction , 168 Paper size and scanned area , 41 Paper Tray , 9 Parallel Memory Transmission , 13 , 19 Parameter Setting , 9 Parameter Setting: Print List , 9 Password , 225 Password (PWD) , 112 Password (SID) , 109 Pause , 65 Personal Box , 157 , 211 Photo , 47 PIN Code Transmission , 10 4 PIN ...

  • Xerox C3000 - page 294

    284 Resending a file , 189 Resolution , 49 Returning the machine to the standb y mode , 5 Routing e-mail received via S MTP , 161 Routing received documents , 157 Routing received documents with SUB Code , 157 RTI → Own Name , 150 S Saving as files , 251 Scanning Two-Sided Originals , 37 Scan Settings , 9 , 47 Scan Size , 51 Scan Type , 47 Search ...

  • Xerox C3000 - page 295

    285 Substitute Reception , 149 Super Fine , 49 Switching between Memory and Immediate Transmission , 13 Switching the reception mode , 153 Switching the titles in the Address Book , 77 Switch Reception Mode , 9 Switch RX Mode , 152 , 15 3 Switch Title , 9 Symbols , 4 System Stat us , 267 T T.37 full mode , 33 , 263 Terminology , 27 Text , 47 , 13 3 ...

  • Xerox C3000 - page 296

    286 EN USA B786-8510A ...

  • Xerox C3000 - page 297

    USA ❖ FCC Requirements 1. This equipment complies with Part 68 of the F CC rules and requi rements adopted by the AC TA. On the cover of this e quipment is a label that con tains, among other info rmation, a product iden - tifier in the format US:AAAEQ##TXXXXX. If requested, th is number must be provided to the telephone company. 2. This equipmen ...

  • Xerox C3000 - page 298

    FAX Option Type C3000 Operating Instructions Facsimile Reference EN USA B786-85 10A ...

Manufacturer Xerox Category Fax Machine

Documents that we receive from a manufacturer of a Xerox C3000 can be divided into several groups. They are, among others:
- Xerox technical drawings
- C3000 manuals
- Xerox product data sheets
- information booklets
- or energy labels Xerox C3000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Xerox C3000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Xerox C3000, service manual, brief instructions and user manuals Xerox C3000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Xerox C3000.

Similar manuals

A complete manual for the device Xerox C3000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Xerox C3000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Xerox C3000.

A complete Xerox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Xerox C3000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Xerox C3000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Xerox C3000, that we can find in the current document
3. Tips how to use the basic functions of the device Xerox C3000 - which should help us in our first steps of using Xerox C3000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Xerox C3000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Xerox C3000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Xerox C3000?

Use the form below

If you did not solve your problem by using a manual Xerox C3000, ask a question using the form below. If a user had a similar problem with Xerox C3000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)