Manual Telex UAD4

8 pages 0.13 mb
Download

Go to site of 8

Summary
  • Telex UAD4 - page 1

    Instruction Sheet General Description The UAD4 Amplified Antenna Splitter makes it possible to operate four UHF wireless diversity microphone receivers on four separate frequen - cies using only two antennas. Features The UAD4 is equipped with TNC type connec - tors. Low loss coaxial cables are also supplied for splitter to receiver antenna jack co ...

  • Telex UAD4 - page 2

    System Configuration Figure 2 illustrates the typical system configura - tion using the UAD4. Figure 3 illustrates an arrangement where two splitters have been cascaded. By connecting one of the outputs of the first splitter to the antenna inputs of the second splitter , three additional re - ceivers may be driven by a single pair of anten - nas. S ...

  • Telex UAD4 - page 3

    -3- T O RECEIVERS ONL Y T O RECEIVERS OR SPLITTERS T O RECEIVERS ONL Y (DO NO T FEED SPLITTERS FR OM SECOND ARY UNITS) ANTENNA ANTENNA INPUT A OUTPUT A 12 3 4 OUTPUT B 12 3 4 INPUT B POWER 90-260 V AC 50-60 Hz POWER OUT 12 3 4 15 VDC INPUT A OUTPUT A 12 3 4 OUTPUT B 12 3 4 INPUT B POWER 90-260 V AC 50-60 Hz POWER OUT 12 3 4 15 VDC Figure 3 Cascadin ...

  • Telex UAD4 - page 4

    Antenna Requirements The UAD4 may be used with a variety of anten - nas. For best results, use a pair of ALP-450 di - rectional log periodic antennas. See Figure 4. The ALP-450 of fers the best performance and broadest bandwidth available. Antenna Placement If antennas are mounted directly to the UAD4, they should be configured as shown in Figure 5 ...

  • Telex UAD4 - page 5

    A nt e n na P l a c e m e nt f o r O p ti m u m Range and Rack Mounting For maximum range and when rack mounting, the antennas must be remotely located. The ALP-450 comes complete with a variety of mounting hardware and 10 feet (3 meters) of low loss coaxial cable. A combination mounting bracket (Model No. AB-2) with 10 feet of coax - ial cable is ...

  • Telex UAD4 - page 6

    12 Volt Power On "Antenna In" Jacks T o power UAA-500 in-line antenna amplifiers, 12 volt power is available on the center pin of the antenna in jacks. This power is disabled when the UAD4 leaves the factory but may be turned on by the installer . T o turn on the 12 volts, first take off the cover of the splitter by removing the screws. T ...

  • Telex UAD4 - page 7

    U AD4 Accessories and Replacement P ar ts AC Power Cables 550024000 Europe 550024002 U.K. 550024013 North America 690513 Japan TP-2 50 OHM/TNC dummy load (For unused outputs on the UAD-4) Part No. 650095 Special low loss antenna cables with TNC connectors UAA-500 Low noise antenna amplifier , 500-900 MHz (antenna not included) Order No. 7186400 ALP ...

  • Telex UAD4 - page 8

    PRINTED IN U.S.A. Copyright© 2004 by Telex TELEX COMMUNICATIONS, INC. All rights reserved July 2004 ...

Manufacturer Telex Category TV Antenna

Documents that we receive from a manufacturer of a Telex UAD4 can be divided into several groups. They are, among others:
- Telex technical drawings
- UAD4 manuals
- Telex product data sheets
- information booklets
- or energy labels Telex UAD4
All of them are important, but the most important information from the point of view of use of the device are in the user manual Telex UAD4.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Telex UAD4, service manual, brief instructions and user manuals Telex UAD4. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Telex UAD4.

Similar manuals

A complete manual for the device Telex UAD4, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Telex UAD4 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Telex UAD4.

A complete Telex manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Telex UAD4 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Telex UAD4, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Telex UAD4, that we can find in the current document
3. Tips how to use the basic functions of the device Telex UAD4 - which should help us in our first steps of using Telex UAD4
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Telex UAD4
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Telex UAD4 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Telex UAD4?

Use the form below

If you did not solve your problem by using a manual Telex UAD4, ask a question using the form below. If a user had a similar problem with Telex UAD4 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)