Manual Seagate KSD-541

18 pages 1.58 mb
Download

Go to site of 18

Summary
  • Seagate KSD-541 - page 1

    -1- Industrial 5-Port Fa st Ethernet Switche s with SFP Slot a nd option al 4 PoE PSE Ports Ba sic Model: KSD-541 PoE Model: KSD-541-P In stallation Guide DOC.080104 ...

  • Seagate KSD-541 - page 2

    -2- (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from tim ...

  • Seagate KSD-541 - page 3

    -3- The information contained in this document is subject to change without prior notice. Copyright (C) . All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. W ARNING: This equi pment ha s been tested a nd found to comply with the li mits for a Cla ss A digital device, pursua nt to Part 15 of the FCC Rules. These limit ...

  • Seagate KSD-541 - page 4

    -4- T a ble of Contents 1. Introduction .................................................................................................. 5 1.1 Features .................................................................................................................. .6 1.2 Product Pa nels .......................................................... ...

  • Seagate KSD-541 - page 5

    -5- 1. Introduction The switches are 5-port Fa st Ethernet switches which are f eatured with four copper ports a nd one combo port. The combo port comes with one RJ-45 a nd one SFP slot. The SFP slot ca n be mounted with a fiber tra nsceiver optionally to support a fiber connection. For more coming PoE (Power Over Ethernet) a pplications, the PoE s ...

  • Seagate KSD-541 - page 6

    -6- 1.1 Fe ature s  Provides 5 10/100Mbps RJ-45 a nd one 100Mbps SFP slot  All copper ports support auto-negoti ation a nd auto-MDI/MDI-X detection  Provides full wire speed forwarding  Supports IEEE 802.3x flow control for full-duplex a nd ba ckpressure for half-duplex  Provides SFP slot for optional optical fiber connection  Pro ...

  • Seagate KSD-541 - page 7

    -7- 1.4 Specif ication s Copper Ports w/h PSE (P2-P5) Compli a nce IEEE 802.3 10Ba se-T , IEEE 802.3u 100Base-TX Connectors Shielded RJ-45 ja cks Pin a ssignments Auto MDI/MDI-X detection Configuration Auto-negoti ation T ra nsmission rate 10Mbps, 100Mbps Duplex support Full/Half duplex Network ca ble Cat.5 UTP Power over Ethernet IEEE 802.3af-comp ...

  • Seagate KSD-541 - page 8

    -8- Power over Ethernet Function (PoE Model) PSE Pin 4,5 Positive of power voltage (T ypical 48V DC) PSE Pin 7,8 Negative of power voltage (T ypical 48V DC) Discovery PD resista nce 15K ~ 33K PD Cla ssification Cla ss 0 ~ 4 Power delivery 15.4W max. (per port) Protection Under voltage protection Over voltage protection Over current detection DC IN ...

  • Seagate KSD-541 - page 9

    -9- 2. In stallation 2.1 Un pa cking The product pa ckage contains: • The switch unit • One product CD-ROM 2.2 Safety Cautions T o reduce the risk of bodily injury , electrical shock, fire, a nd da mage to the product, observe the following precautions. • Do not service any product except as explained in your system documentation. • Opening ...

  • Seagate KSD-541 - page 10

    -10- 2.4 Din-Rail Mounting The steps to mount the switch on a Din-rail are: One Din-rail mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit. Mount the device on a Din-rail. ...

  • Seagate KSD-541 - page 11

    -11- 2.5 Pa nel Mounting One pa nel mounting bra cket is provided in the product pa ckage a s shown below: Install the bra cket on the bottom of the switch unit. The final di mension after pa nel bra cket is installed is shown below: 2.6 Applying Power The switch provides two types of power interfa ces, terminal block a nd DC power jack f or rece i ...

  • Seagate KSD-541 - page 12

    -12- Using T erminal Blocks Three terminal conta cts are provided: V dc Positive ( + ) termin al V dc Negative ( - ) termin al Cha ssis ground * Working V dc for general a pplication: +6V ~ +60V DC * Working V dc for PoE a pplication : +43V ~ +54V DC (T yp. 48V) One 3P terminal plugs are provided together with the switch. The plug is shown below: P ...

  • Seagate KSD-541 - page 13

    -13- 3. M a king Connection s 3.1 Ma king UTP Conne ction s The copper ports support the following connection type s a nd dista nce s: Network Cables 10BASE-T : 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm 100BASE-TX: 2-pair / 4-pair UTP Cat. 5, EIA/TIA-568B 100-ohm Link dista nce: Up to 100 meters Auto MDI/MDI-X Function This function allows the p ...

  • Seagate KSD-541 - page 14

    -14- 3.3 Ma king PoE Connection s This section describes how to make a connection between a PSE port a nd a PoE PD device. For the PoE switch model, Port 2, Port 3, Port 4 a nd Port 5 are equi pped with PoE PSE function. The ports are ena bled to deliver power together with network signal to a connected powered device vi a Cat.5 ca ble. T o make a ...

  • Seagate KSD-541 - page 15

    -15- 3.4 LED Indication L ED Function State Interpretation POWER Power status O N The power is supplied to the switch. OFF The power is not supplied to the switch. LIN K/ACT Por t l ink status O N A port link is e sta blished. (No traf fic) BLIN K Port link is up a nd there is traffic. OFF Port link is down. 100M/10M Port speed status O N Speed 100 ...

  • Seagate KSD-541 - page 16

    -16- 4. Application s 4.1 Application s with Ba sic Switch Model The following figure illustrates a ba sic switch model connects five computers vi a Cat.5 ca ble s. The following figure illustrates a ba sic switch model connects four computers vi a Cat.5 ca bles a nd uplink to a fiber ba ckbone network. ...

  • Seagate KSD-541 - page 17

    -17- 4.2 Applications with PoE Switch Model The figure below illustrates a PoE switch connects f our PoE IP camera s via Cat.5 ca ble s a nd uplinks to a fiber ba ckbone: The figure below illustrates a PoE switch connects f our PoE WLAN a ccess points vi a Cat.5 ca bles a nd uplinks to a ba ckbone: ...

  • Seagate KSD-541 - page 18

    -18- The figure below illustrates a PoE switch powered by a 48V DC power a da pter connects four PoE medi a converters vi a Cat.5 ca bles a nd uplinks to a fiber ba ckbone: ...

Manufacturer Seagate Category Switch

Documents that we receive from a manufacturer of a Seagate KSD-541 can be divided into several groups. They are, among others:
- Seagate technical drawings
- KSD-541 manuals
- Seagate product data sheets
- information booklets
- or energy labels Seagate KSD-541
All of them are important, but the most important information from the point of view of use of the device are in the user manual Seagate KSD-541.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Seagate KSD-541, service manual, brief instructions and user manuals Seagate KSD-541. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Seagate KSD-541.

Similar manuals

A complete manual for the device Seagate KSD-541, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Seagate KSD-541 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Seagate KSD-541.

A complete Seagate manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Seagate KSD-541 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Seagate KSD-541, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Seagate KSD-541, that we can find in the current document
3. Tips how to use the basic functions of the device Seagate KSD-541 - which should help us in our first steps of using Seagate KSD-541
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Seagate KSD-541
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Seagate KSD-541 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Seagate KSD-541?

Use the form below

If you did not solve your problem by using a manual Seagate KSD-541, ask a question using the form below. If a user had a similar problem with Seagate KSD-541 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)