Manual Porter-Cable 557

23 pages 0.54 mb
Download

Go to site of 23

Summary
  • Porter-Cable 557 - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable 557 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and propert ...

  • Porter-Cable 557 - page 3

    3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...

  • Porter-Cable 557 - page 4

    4 Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. GENERAL SAFETY RULES* SAVE THESE INSTRUCTIONS 1) Work area ...

  • Porter-Cable 557 - page 5

    5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...

  • Porter-Cable 557 - page 6

    6 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Wait for the cutter to stop before setting the tool down. An exposed cutter may ...

  • Porter-Cable 557 - page 7

    7 SAVE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g .................... ...

  • Porter-Cable 557 - page 8

    8 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amp ...

  • Porter-Cable 557 - page 9

    9 FOREWORD Model 557 is designed to cut the grooves required for Porter-Cable biscuit sizes “FF”, “0”, “10”, and “20”. Adjustments are also provided which allow the tool to cut grooves for the following plate joiner accessories sold by other manufacturers: #6 biscuits, Duplex accessories, and Simplex accessories. NOTE: This tool is ...

  • Porter-Cable 557 - page 10

    10 ADJUSTING DEPTH OF GROOVE A “quick set” depth adjusting turret (A) Fig. 2, provides for quick changes in depth of cut to accommodate the various sizes of available biscuits and other accessories. To set depth of cut: rotate depth adjusting turret until desired size marking on turret aligns with the index mark (B) Fig. 2. The following depth ...

  • Porter-Cable 557 - page 11

    11 3. While holding adjustment knob in desired position: tighten lock-nut firmly. ADJUST ABLE FENCE Model 557 is equipped with an integral, adjustable fence which: • Provides micro height adjustment, distance scale includes indexes to top of cut, to center of cut, and to bottom of cut. • Tilts 0° through 135°, with an adjustable stop at 90°. ...

  • Porter-Cable 557 - page 12

    12 FINE ADJUSTMENT (90° Position) The adjustable 90° stop is factory adjusted for 90° and should not require additional adjustment. If “fine tuning” of the stop position is required: use a 5 / 64 " hex wrench (not furnished), to rotate set-screw (F) Fig. 6, as required. Rotate the set-screw clockwise to reduce the angle of the fence, ro ...

  • Porter-Cable 557 - page 13

    13 8. Continue to hold spindle lock button while using the hex wrench (furnished with tool), to tighten blade retaining bolt securely, (by rotating clockwise). 9. Rotate the “quick set” depth adjusting turret (A) Fig. 12, to the “FF” position. 10. Lift safety lever (A) Fig. 13, fully retract the plunge mechanism, and reposition the safety l ...

  • Porter-Cable 557 - page 14

    14 ALIGNMENT PLA TE (For Narrow Stock) When joining narrow material, it will be necessary to install the alignment plate (A) Fig. 15, (furnished with tool). The alignment plate provides added support for narrow material, and has index marks to aid in centering the cut in the narrow material. Index marks are provided for 1 1 / 2 " wide, and 2&q ...

  • Porter-Cable 557 - page 15

    15 A TT ACHING DUST BAG Depress spring clips (A) Fig. 18, and clip dust bag (B) on end of dust/chip deflector (C). The bag is equipped with a zipper to ease emptying of the collected material. Vacuum Hose A standard 1" vacuum hose can be attached to the dust port to provide a means for connecting the tool to your vacuum cleaner or dust collect ...

  • Porter-Cable 557 - page 16

    16 PRACTICE CUTS After each set-up or adjustment to the tool, it is recommended you make several practice cuts in scrap material to verify desired operation. CORNER JOINTS 1. Layout groove positions as described in POSITIONING GROOVES. 2. Set depth stop turret to desired biscuit (or other accessory), size. 3. Set the tilt fence to the 90° position ...

  • Porter-Cable 557 - page 17

    17 7. Hold tool firmly as shown in Fig. 21, squeeze trigger switch to start tool. 8. At a slow, steady pace, push tool forward in base as far as depth stop allows. 9 . Release trigger switch to stop tool and remove tool from work. 1 0 . Repeat steps 6 through 9 until all the grooves for this joint are completed. NOTE: Assemble all joints and verify ...

  • Porter-Cable 557 - page 18

    18 8. At a slow, steady pace, push tool forward in base as far as depth stop allows. 9. Release trigger switch to stop tool and remove tool from work. 10. Repeat steps 5 through 8 until all the grooves in workpiece “A” are completed. 11. Follow steps 3 through 10 of CORNER JOINTS Section to complete required grooves in workpiece “B” Fig. 23 ...

  • Porter-Cable 557 - page 19

    19 7. Hold tool firmly as shown in Fig. 28, and squeeze trigger switch to start tool. 8. At a slow, steady pace, push tool forward in base as far as depth stop allows. 9. Release trigger switch to stop tool and remove tool from work. 10. Repeat Steps 5 through 8 until all the grooves for this joint are completed. NOTE: Assemble all joints and verif ...

  • Porter-Cable 557 - page 20

    20 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail t ...

  • Porter-Cable 557 - page 21

    21 REPLACEMENT P ARTS When servicing use only identical replacement parts. For a service parts list or to learn more about Porter-Cable visit our website at www.porter-cable.com SERVICE AND REP AIRS All quality tools will eventually require servicing, or replacement of parts due to wear from normal use. For assistance with your tool, visit our webs ...

  • Porter-Cable 557 - page 22

    22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable 557 - page 23

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Biscuit Joiner

Documents that we receive from a manufacturer of a Porter-Cable 557 can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- 557 manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable 557
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable 557.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable 557, service manual, brief instructions and user manuals Porter-Cable 557. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable 557.

A complete manual for the device Porter-Cable 557, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable 557 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable 557.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable 557 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable 557, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable 557, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable 557 - which should help us in our first steps of using Porter-Cable 557
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable 557
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable 557 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable 557?

Use the form below

If you did not solve your problem by using a manual Porter-Cable 557, ask a question using the form below. If a user had a similar problem with Porter-Cable 557 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)