English dropdown-ico

Manual Snapper Clean Sweep Twin Catcher

18 pages 0.71 mb
Download

Go to site of 18

Summary
  • Snapper Clean Sweep Twin Catcher - page 1

    A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T win Catcher Mfg. No. Description 1694498 Clean Sweep Twin Catcher 1726793 Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Clean Sweep T win Catcher ...

  • Snapper Clean Sweep Twin Catcher - page 2

    1 Initial Collector Assembl y Install Cov er & Bags ......................................13 Normal Remov al & Installation Removing the Gr ass Catcher ........................14 Installing the Grass Catcher ..........................15 Hard ware Identification & T or que Specifications ....................................16 NOTE: In th ...

  • Snapper Clean Sweep Twin Catcher - page 3

    2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This u ...

  • Snapper Clean Sweep Twin Catcher - page 4

    BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i ...

  • Snapper Clean Sweep Twin Catcher - page 5

    Initial T urbo Installation 4 50" 44" 35 49 48 7 8 6 4 5 Existing Hardware (Bolt, W asher , Lockwasher , & Nut) 40 41 42 43 22 38 44 1 1 2 3 9 18 18 15 16 17 8 14 13 Existing Pulley & Spacer T orque to 55-70 ft. lbs. 24 25 26 27 32 31 30 36 37 38 22 39 19 27 8 27 34 27 45 11 21 2 22 20 23 33 29 10 12 47 46 17 28 Existing Hardware ...

  • Snapper Clean Sweep Twin Catcher - page 6

    Initial T urbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discard the cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5). 3 Slide the deflector rod (D) through the pivo ...

  • Snapper Clean Sweep Twin Catcher - page 7

    Initial T urbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts. C B Figure 6. Install Deflector A. 13/64 Hole Locations ...

  • Snapper Clean Sweep Twin Catcher - page 8

    Initial T urbo Installation 7 Install Idler Assembl y & Belt Co ver 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3. Mount the idler pulley assembly (A) to the deck using the two 5/16-18x 7/8 capscrews (C) and 5/16 ...

  • Snapper Clean Sweep Twin Catcher - page 9

    Initial T urbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C), washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on the support bracket. Different belt covers are required for different applications. Refer to Figure ...

  • Snapper Clean Sweep Twin Catcher - page 10

    Initial T urbo Installation 9 Mower Dec k Arbor Pulley Mower Dec k T urbo Driv e Pulley T urbo Driv e Pulley Idler Pulleys T o Slac k en Belt CA UTION Before you begin operating the unit with the Turbo attached, be certain you have read all of the safety and operational information on the last page of this instruction sheet, as well as the Operator ...

  • Snapper Clean Sweep Twin Catcher - page 11

    Initial Counter Balance & W eight Carrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier Installation A. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D. Rod B D A L F G H K I J E C M A. Rear Deck Lift Lever B. Trunnion (Existing) C. Hair Pin (Existi ...

  • Snapper Clean Sweep Twin Catcher - page 12

    Initial Hitch & T ube Installation 11 Figure 1. Install Hitch Plate A. Hitch Plate E. Upper & Lower B. Heat Shield Bumper C. Capscrews, F. Washer 1/2-13 x 1-1/4 G. New Holes, 17/32” D. Locknuts, 1/2-13 H. Existing RH Holes Figure 3. Install Back Plate A. Back Plate and Support C. Hitch Plate B. Hair Pin D. Rod B A D C Figure 2. Install Hi ...

  • Snapper Clean Sweep Twin Catcher - page 13

    Initial Hitch & T ube Installation 12 Figure 4. Assemble Tubes & Deflector A E C F B A. Upper Tube B. Middle Tube C. Lower Tube D. Nut, Nylock, 10-24 x 3/4 E. Washer F. Screw, Truss Head, 10-24 G. Holes H. Clip and Hardware Assemble T ubes & Deflector 1. Insert the lower tube (C, Figure 4) into middle tube (B). Secure the tubes as shown ...

  • Snapper Clean Sweep Twin Catcher - page 14

    Initial Collector Assembly 13 Figure 7. Install Catcher A. Nut, #10-32 E. Hinge Pin B. Handle F. Bags C. Screw, #10-32 x 1/2 G. Hair Pin Clip D. Cover Figure 8. Install Cable A. Cable C. Washer B. Support A B C D E F G COLLECT OR ASSEMBL Y Install Cover and Ba gs 1. Hang the bags (F, Figure 7) on the horizontal sup- port. Note: If desired, the bags ...

  • Snapper Clean Sweep Twin Catcher - page 15

    Normal Removal & Installation 14 NORMAL REMO V AL & INST ALLA TION Removing the Grass Catc her 1. Disconnect the tubes (A, Figure 9) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B, Figure 9) and clevis pin (D) securing the cover (E). Disconnect the cable (see Figure 8). Remove the cover (E). 3. Remove and em ...

  • Snapper Clean Sweep Twin Catcher - page 16

    Removing and Reattaching Grass Catcher 15 Installing the Grass Carc her 1. Set the back plate & support (A, Figure 11) on pins of hitch plate (C). Secure with rod (D) and hair pin (B). 2. Install the bags (C, Figure 12). 3. Install the cover (E, Figure 12). Secure with the cle- vis pins (F) and hair pin clips (B). NOTE: Push the hair pin clips ...

  • Snapper Clean Sweep Twin Catcher - page 17

    16 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8 ...

  • Snapper Clean Sweep Twin Catcher - page 18

    MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...

Manufacturer Snapper Category Lawn Sweeper

Documents that we receive from a manufacturer of a Snapper Clean Sweep Twin Catcher can be divided into several groups. They are, among others:
- Snapper technical drawings
- Clean Sweep Twin Catcher manuals
- Snapper product data sheets
- information booklets
- or energy labels Snapper Clean Sweep Twin Catcher
All of them are important, but the most important information from the point of view of use of the device are in the user manual Snapper Clean Sweep Twin Catcher.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Snapper Clean Sweep Twin Catcher, service manual, brief instructions and user manuals Snapper Clean Sweep Twin Catcher. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Snapper Clean Sweep Twin Catcher.

Similar manuals

A complete manual for the device Snapper Clean Sweep Twin Catcher, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Snapper Clean Sweep Twin Catcher by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Snapper Clean Sweep Twin Catcher.

A complete Snapper manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Snapper Clean Sweep Twin Catcher - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Snapper Clean Sweep Twin Catcher, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Snapper Clean Sweep Twin Catcher, that we can find in the current document
3. Tips how to use the basic functions of the device Snapper Clean Sweep Twin Catcher - which should help us in our first steps of using Snapper Clean Sweep Twin Catcher
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Snapper Clean Sweep Twin Catcher
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Snapper Clean Sweep Twin Catcher in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Snapper Clean Sweep Twin Catcher?

Use the form below

If you did not solve your problem by using a manual Snapper Clean Sweep Twin Catcher, ask a question using the form below. If a user had a similar problem with Snapper Clean Sweep Twin Catcher it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)