Manual Ubiquiti Networks AF-24

36 pages Not applicable
Download

Go to site of 36

Summary
  • Ubiquiti Networks AF-24 - page 1

    24 GHz Point to Point 1.4+ Gbps Radio Model: AF-24 ...

  • Ubiquiti Networks AF-24 - page 2

    ...

  • Ubiquiti Networks AF-24 - page 3

    Introduction Thank you f or purchasing the Ubiquiti Networks® airF iber® 24GHz Point-t o-Point Radio . This Quick Start Guide is designed to guide you through installation, show y ou how to access the airF iber Configuration Interface, and explain how t o set up an airF iber link. This Quick Start Guide also includes the warranty terms and is ...

  • Ubiquiti Networks AF-24 - page 4

    Hardware Overview Side Alignment Bracket Elevation Adjustment Azimuth Adjustment Ground Bonding Point Lock Bolts Lock Bolts 2 airFiber® AF-24 Quick Start Guide ...

  • Ubiquiti Networks AF-24 - page 5

    Back Lock Bolts Lock Bolts Azimuth Adjustment Lock Bolts Lock Bolts Cover L ock Elevation Adjustment Port Cover 3 Hardware Overview ...

  • Ubiquiti Networks AF-24 - page 6

    Inter faces RESET D ATA AUX CONFIG LED Display Interface Description RESET T o reset to factory defaults, press and hold the Reset button for more than fiv e seconds while the unit is already powered on. D ATA 10/100/1000 Mbps port handles all user traffic. AUX Port for audio tone aiming . LED Display Digital display used for po wer , status, and m ...

  • Ubiquiti Networks AF-24 - page 7

    LED Stat e Status D ATA Speed Off 10/100 Mbps On 1000 Mbps Link/Act Off No Ethernet Link On Ethernet Link Established Random Flashing Ethernet Activity AUX GPS Off No GPS Synchronization On Operational (Strong Signal) Normal Flash* Operational ( Weak Signal) Modulation Off ¼x or 1x (QPSK SISO) Short Flash* 2x (QPSK MIMO) Normal Flash* 4x (16QAM MI ...

  • Ubiquiti Networks AF-24 - page 8

    Installation Requirements • 17 mm wrench • 13 mm socket wrench or driver • Clear line of sight between airF iber radios • Clear view of the sky for proper GPS operation • Mounting location with < 0.5° displacement due to twist and sway under wind loading • Mounting point: • At least 1 meter below the highest point on the structure ...

  • Ubiquiti Networks AF-24 - page 9

    • Once configuration is complet e, disconnect the cables to mov e the airFiber r adios. • Reconnect at the site. • After you hav e mounted the airFiber radios , establish and optimize the RF link. Connecting P ower over E thernet 1. T urn the Cover Lock t o the Unlocked icon. Slide the Port Cov er down to remov e it. 2. Connect an Ethernet ca ...

  • Ubiquiti Networks AF-24 - page 10

    3. Connect the other end of the Ethernet cable from the D ATA port to the Ethernet por t labeled POE on the GigE PoE Adapter . 4. Connect the Power C ord to the power por t on the GigE PoE Adapter . Connect the other end of the Power Cord to a po wer source. 8 airFiber® AF-24 Quick Start Guide ...

  • Ubiquiti Networks AF-24 - page 11

    airF iber Configuration The instructions in this section explain how to access the airFiber Configuration Interface and configure the follo wing settings: • Wireless Mode Configure one airF iber AF-24 as the Master and the other as the Slave . • Duplex The airFiber AF-24 supports both half-duplex and full-duplex operation. Half-duplex operation ...

  • Ubiquiti Networks AF-24 - page 12

    1. Connect an Ethernet cable from your comput er to the CONFIG port on the airFiber AF-24. 2. Configure the Ethernet adapt er on your computer with a static IP address on the 192.168.1.x subnet (for example , 192.168.1.100). 3. Launch your web bro wser . T ype http://192.168.1.20 in the address field and press enter (PC) or r eturn (Mac). 4. The lo ...

  • Ubiquiti Networks AF-24 - page 13

    5. Click the Wireless tab . 6. Enter the Basic Wireless Settings : a. For one airF iber AF-24, selec t Master from the Wireless Mode drop-down. F or the other airFiber AF-24, keep the default, Slave . b. Enter a name in the Link Name field. This should be the same on both the Master and the Slave . c. F or the D uplex drop-down: - Half Duplex The d ...

  • Ubiquiti Networks AF-24 - page 14

    7. Configure the Wireless Security : a. Selec t the AES Key T ype , HEX or ASCII . b. For the Key field: - HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F , or a-f ). Y ou can omit zeroes and use colons , similar to the IPv6 format. Note: The airF iber Configuration Interface suppor ts IPv6 formats ex cluding dotted quad and "::" ( ...

  • Ubiquiti Networks AF-24 - page 15

    Hardware Installation T o install the airF iber AF-24: 1. Insert the four Carriage Bolts into the Pole Mount Br acket . 2. Attach the P ole Mount Brack et to a pole. Note: The mounting assembly can accommodate a Ø 51 - 101 mm (2.0" - 4.0") pole. a. Orient the Pole Mount Brack et around the pole so it is aimed in the direction of the othe ...

  • Ubiquiti Networks AF-24 - page 16

    3. Loosen, but do NO T remove the eight Lock Bolts located on the Alignment Brack et . 4. Ensure that there is a 6 mm gap between the head of each M8x14 Serrated Flange Screw and the Alignment Br acket . 6 mm 14 airFiber® AF-24 Quick Start Guide ...

  • Ubiquiti Networks AF-24 - page 17

    5. Lift the airFiber AF-24 and align the f our M8x14 Serrated Flange Screws with the slots on the Pole Mount Br acket. Seat the screws in the slots. Securely tighten the screws . W ARNING: T o prevent injury , ensure that all four screws are seated and fully tightened . 15 Hardware Installation ...

  • Ubiquiti Networks AF-24 - page 18

    6. Attach a ground wire: a. Remove the nut from the Ground Bonding Point . b. Attach a ground wire (min. 8 A WG or 10 mm 2 ) to the lug and replace the nut to secure the wire . c. Secure the other end of the ground wire to a grounded mast, pole, t ower , or grounding bar . W ARNING: F ailure to properly ground your airF iber units will void y our w ...

  • Ubiquiti Networks AF-24 - page 19

    Connecting Ethernet 1. T urn the Cover Lock t o the Unlocked icon. Slide the Port Cov er down to remov e it. 2. Connect a TOUGHC able or other outdoor , shielded CA T5e/6 cable to the DA T A port. 3. Create a strain relief f or the Ethernet cable by feeding a Cable Tie through the tie slot under the cable. Then wrap the Cable Tie around the cabl ...

  • Ubiquiti Networks AF-24 - page 20

    4. Connect the other end of the Ethernet cable from the D ATA port to the Ethernet por t labeled POE on the GigE PoE Adapter . 5. Connect an Ethernet cable from your netw ork to the Ethernet port labeled L AN on the GigE PoE A dapter. 6. Connect the Power C ord to the power por t on the GigE PoE Adapter . Connect the other end of the Power Cord to ...

  • Ubiquiti Networks AF-24 - page 21

    Below is a diagram of a finished installation with recommended surge protectors installed . Ground to Pole, T ower, or Grounding Block (Max. 1 m from Ground Bonding Point) Max. 1 m Outdoor GigE PoE Surge Protector EdgeRouter ™ GigE PoE Adapter Power Source Outdoor GigE PoE Surge Protector 19 Connecting Ethernet ...

  • Ubiquiti Networks AF-24 - page 22

    Alignment Tips • Fine-tuning is best achiev ed by a pair of installers with a dedicated , two-way communication link: one installer makes adjustments on one airFiber r adio while the other installer reports the received signal level at the other airF iber radio. Fine-tuning (see F ine-T uning the Link ) is necessar y because the main lobe of the ...

  • Ubiquiti Networks AF-24 - page 23

    2. F or the Master and Slave , ensure the A zimuth (AZ) and Elevation (EL) Adjustment Bolts ar e in the middle of their adjustmentranges. Elevation (EL) Adjustment Bolt Azimuth (AZ) Adjustment Bolt 3. Master Aim the Master at the Slave . If necessary , adjust the Master 's position on the pole: a. Loosen the Hex Nuts . b. Adjust the Pole Mo ...

  • Ubiquiti Networks AF-24 - page 24

    5. Master Adjust the azimuth and elevation of the Master until the strongest received signal lev el is displayed on the LED Display of the Master . a. Sweep the Azimuth (AZ) Adjustment Bolt of the Master through its adjustment range. Master Azimuth (AZ) Adjustment Bolt b. Sweep the Elevation (EL) A djustment Bolt of the Master through its adjustmen ...

  • Ubiquiti Networks AF-24 - page 25

    F ine-T uning the Link The Azimuth (AZ) and Elevation (EL) Adjustment Bolts of the Alignment Brack et adjust the azimuth and elevation within a range of ±10°. F or accurate alignment, make adjustments on one end of the link while the other installer reports the received signal level at the other end of the link. Do NOT make simultaneous adjustmen ...

  • Ubiquiti Networks AF-24 - page 26

    There are three methods f or determining the received signal level: • LED Display (described abov e) • airF iber Configuration Interface • Audio tone (optional equipment requir ed) Refer to the airF iber AF-24 User Guide for instructions on the airFiber C onfiguration Inter face and audio tone methods. The U ser Guide is av ailable at: docume ...

  • Ubiquiti Networks AF-24 - page 27

    Specifications airFiber AF-24 Dimensions 649 x 426 x 303 mm (25.55 x 16.77 x 11.93") W eight 10.5 kg (23.15 lb) Mount Included Operating F requency 24.05 – 24.25 GHz Max Pow er Consumption < 50W Po wer Supply 50V , 1.2A PoE GigE A dapter (Included) Po wer Method Passiv e Power over E thernet (42-58VDC) Certications CE, FC C, IC Mountin ...

  • Ubiquiti Networks AF-24 - page 28

    Electrical Safety Information 1. Compliance is required with r espect to voltage, frequency , and current requirements indicated on the manufacturer’ s label. Connection to a different pow er source than those specified may result in impr oper operation, damage to the equipment or pose a fire hazard if the limitations are not follow ed. 2. There ...

  • Ubiquiti Networks AF-24 - page 29

    W arranty Conditions The above warr ant y does not apply if the Product: (I) has been modified and/or altered , or an addition made thereto, except by Ubiquiti Netw orks, or Ubiquiti Networks’ authorized representatives , or as approved by Ubiquiti Networks in writing; (II) has been painted , rebranded or physically modified in an y way ; (III) h ...

  • Ubiquiti Networks AF-24 - page 30

    Disclaimer EX CEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NET WORKS, ITS AFFILIA TES, AND ITS AND THEIR THIRD P ART Y DA T A, SERVICE, SOFT W ARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENT A TION OR W ARRANT Y OF ANY KIND, EXPRESS, IMPLIED OR ST A TUTORY , INCLUDING, BUT NO T LIMITED TO , REPRESENT A TIONS, GUA ...

  • Ubiquiti Networks AF-24 - page 31

    Note Some countries, states and pr ovinces do not allow ex clusions of implied warranties or conditions, so the abo ve exclusion may not apply to you . Y ou may ha ve other rights that vary from countr y to country , state to state, or pro vince to province. Some countries , states and provinces do not allow the exclusion or limitation of liability ...

  • Ubiquiti Networks AF-24 - page 32

    Industr y Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian CAN ICES-3(A). T o reduce potential radio interference to other users , the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e .i.r.p .) is not more than that permitted for successful communication. This devic ...

  • Ubiquiti Networks AF-24 - page 33

    CE Mark ing CE marking on this product represents the product is in compliance with all directives that are applicable to it. This equipment is intended t o be accessed only by service personnel and/or trained professionals. Alert Sign (!) Follows CE Marking Alert sign must be indicated if a restriction on use applied to the product and it must fol ...

  • Ubiquiti Networks AF-24 - page 34

    PHRRJL090514 Magyar [Hungarian] Alulírott, UBIQUITI NET WORKS nyilatkozom, hogy a UBIQUITI NET WORKS device, megfelel a vonatkoz ó alapvetõ követelmén yeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska [Icelandic] Hér me l sir UBIQUITI NET WORKS yfir ví a UBIQUITI NET WORKS device, er í samræmi vi grunnkröfur og a rar kr? ...

  • Ubiquiti Networks AF-24 - page 35

    ...

  • Ubiquiti Networks AF-24 - page 36

    © 2012-2014 Ubiquiti Networks, Inc. All rights reserved . Ubiquiti, UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo , airFiber , EdgeRouter, and T OUGHCable are trademarks or registered trademarks of UbiquitiNetworks ,Inc . in the United States and inother countries. All other trademarks are the property of their respecti ...

Manufacturer Ubiquiti Networks Category Access Point

Documents that we receive from a manufacturer of a Ubiquiti Networks AF-24 can be divided into several groups. They are, among others:
- Ubiquiti Networks technical drawings
- AF-24 manuals
- Ubiquiti Networks product data sheets
- information booklets
- or energy labels Ubiquiti Networks AF-24
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ubiquiti Networks AF-24.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ubiquiti Networks AF-24, service manual, brief instructions and user manuals Ubiquiti Networks AF-24. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ubiquiti Networks AF-24.

A complete manual for the device Ubiquiti Networks AF-24, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ubiquiti Networks AF-24 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ubiquiti Networks AF-24.

A complete Ubiquiti Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ubiquiti Networks AF-24 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ubiquiti Networks AF-24, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ubiquiti Networks AF-24, that we can find in the current document
3. Tips how to use the basic functions of the device Ubiquiti Networks AF-24 - which should help us in our first steps of using Ubiquiti Networks AF-24
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ubiquiti Networks AF-24
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ubiquiti Networks AF-24 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ubiquiti Networks AF-24?

Use the form below

If you did not solve your problem by using a manual Ubiquiti Networks AF-24, ask a question using the form below. If a user had a similar problem with Ubiquiti Networks AF-24 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)