Manual EverFocus 264x2

134 pages 3.64 mb
Download

Go to site of 134

Summary
  • EverFocus 264x2 - page 1

    I n s t r u c t i o n M a n u a l P P A A R R A A G G O O N N 2 2 6 6 4 4 x x 4 4 / / 2 2 6 6 4 4 x x 2 2 S S e e r r i i e e s s D D V V R R ...

  • EverFocus 264x2 - page 2

    E V E R F O C U S E L E C T R O N I C S C O R P O R A T I O N P A R A G O N 2 6 4 x 4 / 2 6 4 x 2 S e r i e s D V R I n s t r u c t i o n M a n u a l  2 01 0 E ve rFo cus El ect roni cs C o rp www .e ve rfoc us. co m Al l rig ht s r ese rve d. No p art o f t he conte nt s o f t hi s manu al may b e rep rod uce d or tra ns mi tte d in any for m o ...

  • EverFocus 264x2 - page 3

    ii ii ii ii Safety Precautions • To avoid an y damage, please consider the following safe ty warnings: • Never place the re corder near to heaters, fu rnaces, other heat sources or under direct solar irradiation. • Operate the device only in locations providing the tolerable operating temperature range 0°C~40°C/32°F ~ +104°F. • Make sur ...

  • EverFocus 264x2 - page 4

    iii iii iii iii This Product is Ro HS compliant . WEEE The inform ation in this manua l was curren t upon publication. The manufactu rer reserves the right to re vise and improve h is products. Therefor e, all specifications are subject to cha nge without prior notice. Misp rints reserved. Please read this m anual careful ly before installing and u ...

  • EverFocus 264x2 - page 5

    iv iv iv iv TABLE OF CONT ENTS 1 PRODUCT OVERVIEW ..................................................................................................... 1 1.1 FEATURES ....................................................................................................................... 1 1.2 PACKAGE CONTENTS ........................................ ...

  • EverFocus 264x2 - page 6

    v v v v 4.1 RECORD ......................................................................................................................... 27 4.2 LOGIN ............................................................................................................................. 27 4.3 SELECT CAMERA OPERATION ....................................... ...

  • EverFocus 264x2 - page 7

    vi vi vi vi 5.8.2 Main M/T SEQ ...................................................................................................................................... 79 5.8.3 Call M/T SEQ ........................................................................................................................................ 79 5.9 DISK SETTING ..... ...

  • EverFocus 264x2 - page 8

    1 1 P R O D U C T O V E R V I E W The latest E verFocus digital video recorder generation is based on H.264 compression technology, resulting in enhance d recording capacity and improved net work image transmission speed with high image quality. Compreh ensive features and extended e vent recording settings enab le the almost universal application ...

  • EverFocus 264x2 - page 9

    2  E x pr ess P la y b ac k : S i m p l y p o i nt , c l i c k a n d dr ag th e p l ay bac k ba r to v i ew pr ev io us r e c or di n gs  E x pr ess S e ar c h : Use i nt ui ti v e pl a y ba c k ba r w it h a s im pl e d r a g & d r op op er a ti on  R emo t e c o n fi gu ra t i o n s u p po r t fr o m b uil t- in w e b i n te r fac e ...

  • EverFocus 264x2 - page 10

    3  M ous e x 1  D VR x 1  U ser ma n u al x 1 ...

  • EverFocus 264x2 - page 11

    4 1 . 3 S P E C I F I C A T IO N S Paragon2 64x4 Paragon2 64x2 Channel Numb er 16 8 16 Compression Format H.264 HDMI Video Output (1080p) Yes Recording Rate/Resolution 480 NTSC /400 PAL (D1) 240 NTSC / 200 PAL (Half D1) 240 NTSC /200 PAL (D1) 480 NTSC / 400 PAL (Half D1) 240 NTSC /200 PAL (D1) Playback Rate/Resolution 480 NTSC /400 PAL (D1) 240 NTS ...

  • EverFocus 264x2 - page 12

    5 RS-485 1 RS485 (3 Terminal connector) Power Source 100VAC~240VAC Dimensions (L x W x H) 410 x 430 x 88 mm / 16.2" x 16.9" x 3.5" Temperatu re 0°C~40°C / 32°F~104°F (20~80% humidity) Certificates CE, FCC, UL Support PTZ Prot ocol EverFocus, Pe lco D, Pelco P, Samsung, Transparent 1 . 4 F R O N T P A N E L Your primary interactio ...

  • EverFocus 264x2 - page 13

    6 16x 4x 9x 13x 10 x PiP The LED will show the selected screen layout. NOTE: The Multiview ke ys are only active in Main monitor - opera tion. 3) DVD+RW Burner: DVD+RW drive for video data export. (for D mod el only) 4) Channel keys 1~16 / 1~8 for full screen display of selected channel. The LED will show the a ctive channel. 5) DIS PLAY: The DISPL ...

  • EverFocus 264x2 - page 14

    7 16) ENTER: En ter Key for menu operation and alarm acknowledge Turn camera au dio ON/OFF when viewing full screen camera. For more details, please refer to Chapter 3.2.1. 17) COPY: The CO PY key opens the menu for video data e xport, details in chapter 4.14 COPY. 18) JOG/SHUTTLE: Shuttle (outer wh eel): In playback mode, use the SHUTTLE fo r fast ...

  • EverFocus 264x2 - page 15

    8 1 . 5 R E A R P A N EL During initial setup you will be connecting your DVR to multiple input and output de vices. This is d one through the rear panel. Figure 1- 2 Rear Panel ○ ○ ○ ○ 1 POWER: Powe r socket for external power supply, 100~240VAC power source ○ ○ ○ ○ 2 eSATA port: Used for external SATA HDD ba y ○ ○ ○ ○ 3 Ma ...

  • EverFocus 264x2 - page 16

    9 ○ ○ ○ ○ 9 HDMI: Conne ct to an HDMI-compatible unit. This HDMI-compa tible unit will be treated as another call monitor. Please use HDMI cables that have the HDMI logo . ○ ○ ○ ○ 10 VGA: Connect to the monitor that has VGA input. ○ ○ ○ ○ 11 MAIN monitor: Main monitor for live and playback display and on -screen display ○ ...

  • EverFocus 264x2 - page 17

    10 1 . 6 H D D I NS T A L L A T I O N Before installing the HDDs, plea se check the location to install HDDs. Th e followin g pictu re shows t he location of built-in HDDs. All other screw holes are re ser ved for ho t-swappable HDDs. ...

  • EverFocus 264x2 - page 18

    11 2 I N S T A L L A T I O N 2 . 1 V I D E O I N P U T S / O UT P UT S I N S T A L L A T I O N Cameras ha ve to be cabled with 75 Ohm video cable, e.g. RG-59, RG-12 and suitable BNC p lugs. Due to inappro priate absorbability, 50 Ohm coax cable (e.g. RG58), antenna cable and further types of coax cable a re not suitable. C h a p t e r 2 ...

  • EverFocus 264x2 - page 19

    12 All connected vid eo sources must provide a 1 V pp NTSC/EIA or PAL/CCIR sta ndard video signal (depending on DV R version PAL / NTSC). When interconne cting transmission lines (twisted pair, f ibre optics, radio) to the video inputs, ma ke sure all receivers are accu rately calibrated. The Main monito r can be connected to BNC, Composite, or VGA ...

  • EverFocus 264x2 - page 20

    13 2 . 2 A UD I O I NS T A LL A TI O N The DVRs p rovide 16/8 audio inputs and 1 audio outpu t. The inputs are desig ned for max. 1 V pp @ 20 KOhm input. The installation h as to be effected with audio coax ca ble and RCA plugs. The output p rovides a max. 1 V pp @ 20 KOhm output line audio signal and may be connected to e.g. a monitor‘s audio in ...

  • EverFocus 264x2 - page 21

    14 2 . 3 A L A R M / C O N T R O L C O N T A CT S I N S T A L LA T I O N The alarm input s can be used for recording start or recording rate adjustment. Furthermore, alarm reactions such as camera switching to monitors, buzzer, e -mail and network alarm are available. 4 a larm output relays can be switched if required. Additionally the DVR provides ...

  • EverFocus 264x2 - page 22

    15 CTRL IN GND CTRL IN GND Idle state Playback 2. Record: The input switches to Record (or Record Standby) as long the contact is closed. CTRL IN GND CTRL IN GND Idle state Record / Record Standby 3. Armed / Dis armed: If the contact is closed, the DVR will switch of f alarm (alarm contact and motion alarm) operat ion. System alarm events are alway ...

  • EverFocus 264x2 - page 23

    16 2. 4.1 Ge ne r al R S- 48 5 b u s i nst al la t i on The EKB-500 ke yboard uses an RS-485 simp lex wiring; the signal is transferred via a sing le twisted pair line. CAT5 ne twork cable is recommended, UPT version (unsh ielded) is sufficient for normal applicat ion. A shielded cab le should be used if the installed cables a re expected to be hig ...

  • EverFocus 264x2 - page 24

    17 An RS-485 d istributor can also be used to increase the maximum nu mber of devices on the bus as well a s the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an additional 1200m, and it also enables the additio nal connection of 31 further devices to each ou tput (the output itself rep resents ...

  • EverFocus 264x2 - page 25

    18 2. 4.5 Sp ee d Do me I n st al la t i o n Speed dome or te lemetry receiver pan/tilt/zoom co ntrol is available through web b rowser or the optional PowerCon software if the DVR is connected to a network. Loca l telemetry control is provided by USB - mouse control or by the optional EKB-500 keyboard. Supported pro tocols: EverFocus, Pelco-D, Pel ...

  • EverFocus 264x2 - page 26

    19 2 . 7 N E T W OR K C ON N E C T IO N This section on ly describes physical conne ction to an Ethernet network. This step must be completed before the DVR’s c an connect to the network. There a re two basic types of connection: 2. 7.1 Di r ec t PC C on n e ct i on thr oug h Cr o s so ver N et wo rk C ab l e The point-to-p oint connection of DVR ...

  • EverFocus 264x2 - page 27

    20 Figure 2- 2 Network Connection through Patch Cable Pinout of straight patchcable 2 . 8 F IN A L I N S T A L L P R O C E S S Once you h ave co mpleted the basic wiring co nnections, you are ready to t urn on the DVR. S imply p lug in the power sou rce. The POWER L ED will light up if power is normal. Once the system has finished loadin g, you can ...

  • EverFocus 264x2 - page 28

    21 3 M O U S E A N D F R O N T P A N E L O P E R A T I O N Paragon 264x4/264x2 se ries DVR suppo rts mu ltiple sources to control t he DVR. It can b e controlled with a mouse, the fron t panel, an EKB500, the handheld remote control, or serial command f rom RS232 port. This chapter will cov er the basic operation usin g mouse and front panel. 3 . 1 ...

  • EverFocus 264x2 - page 29

    22 Figure 3- 2 OSD Menu ○ 1 In section 1, the re are ten setup options availab le. Move the mouse over an icon and click to select it. ○ 2 In section 2, the categories for the selected icon will be displayed. Click on a wo rd to select it. ○ 3 In section 3, a ll the details for the selected option will be av ailable. Click on a field to make ...

  • EverFocus 264x2 - page 30

    23 * Note about on-scr een keyboard: Click on a button to input that character. The buttons on the right and bottom have the following funct ions: Delete Dele te the letter Done Confirm the selection All Caps Switch to capital letters Space Enter a space ← Move to left → Move to right Cancel Cance l and exit from the keyboard ...

  • EverFocus 264x2 - page 31

    24 3 . 2 G E N E R A L FR O N T P A N E L O P E R A T I ON 3. 2.1 Ho w to se l ec t a ch an n e l / E na b l e a u di o 1. In a view consisting of more than one channel, turning Jog or Shuttle can scroll th rough each channel that is displayed. The selected channel will be high lighted by white frame. 2. While one channel is se lected, click “Ent ...

  • EverFocus 264x2 - page 32

    25 Figure 3- 3 (OSD Menu) ○ 1 In section 1, the re are ten setup options availab le. Use Jog or Shuttle to highligh t an icon and press “ Enter ” to select it. ○ 2 In section 2, the main options for the selected icon will be displayed. Use Jog to highligh t an option and press “ Enter ” to se lect it. ○ 3 In section 3, a ll the detail ...

  • EverFocus 264x2 - page 33

    26 Bar : Press “ Enter ” key to activate the slider, then use Jog to adjust the setting. Press “ Enter ” again to finalize the changes. ...

  • EverFocus 264x2 - page 34

    27 4 G E N E R A L D V R O P E R A T I O N S This ch apter introduces the operations o n major functions including playback, layout change, sequence, triplex operatio ns, copy, and search. 4 . 1 R E C OR D By default, the DV R will always be in record mode. When the DVR is turned on, it will start to record. The exceptions are: 1. DVR will not reco ...

  • EverFocus 264x2 - page 35

    28 + To input passwo rd using front panel: press “ Enter ” key to show the on-screen keyboard (see Figure 4 -2 On-screen Keyboa rd). Use Jog or Shuttle to highligh t each character and press “ Enter ” key on f ront panel to input the selected characters. When finished, high light “ Done ” and press “ Enter ” key on front panel to co ...

  • EverFocus 264x2 - page 36

    29 By front pane l: Press key to enter P layback Setup Menu . A playback bar will sho w as the figure below: 2009/05/25 09 :09:30PM 2009/05/25 09 :09:40PM 2009/05/25 09 :10:30PM 1. Stop key: press to stop playback 2. Slow Reverse key: press to slow reverse playback 3. Pause key: press to pau se playback 4. Slow Forward ke y: press to slow forward p ...

  • EverFocus 264x2 - page 37

    30 4 . 6 P T Z 4. 6.1 Ge ne r al P T Z con t r ol Right-click to b ring up the menu bar and click on to enter PTZ Menu . The following actio ns can be performed using the PTZ Menu : 1. Use Direction Arrows (up, down, left, righ t) to move the camera to the desired direction and angle . 2. In Zoom option , Click “ Z+” to zoom closer or “ Z-” ...

  • EverFocus 264x2 - page 38

    31 Click “ C ” to clear the digit in ce ll Click “ X ” at top-right corner to clo se PTZ menu. Click “ Exit ” to leave PTZ function. 4. 6.2 E xp r e ss co n t ro l P T Z When PTZ menu is c losed, the mouse curso r will chan ge to a d ifferent icon in different areas of the sc reen. User can contro l PTZ direction, zoom, and focus by cli ...

  • EverFocus 264x2 - page 39

    32 4 . 7 L A Y O U T The DVR has a to tal of seven display modes available . The different available layouts a re shown below: (Full screen) (PIP) (4 screen s) (9 screens) (10 screens) (13 scree ns) (16 screens) NOTE: PIP d isplay is not available in Playback mode To change layout, follow the steps below: By mouse: Righ t-click to bring up the menu ...

  • EverFocus 264x2 - page 40

    33 By front pane l: Press any channel key to bring that channel to full screen mode. 4 . 8 C H A NN E L S W I T C H I NG Use this function to change channel position 1. Select one camera 2. Press Channe l button . 3. Click on the channel number you wish to switch on cha nnel bar. The display of channel will be switched. EX: Select camera1 and enter ...

  • EverFocus 264x2 - page 41

    34 4. Press again t o show both status information and camera information. 5. Press again t o hide all information. 4 . 1 0 S E Q U EN C E 1. By mouse: Click Sequence button to enter the auto sequential switching mode. 2. By front panel: Click Sequence button on front panel to enter the auto sequential switching mode. 4 . 1 1 M O NI T O R The DVR c ...

  • EverFocus 264x2 - page 42

    35 4 . 1 2 Z O O M 1. Make sure no camera s are in playback mode 2. Select one camera 3. Right-click to bring u p the menu bar and click button, or press ”Zoom” key on front panel. 4. When in ZOOM mode, the mouse cu rsor will change to a different icon in different a reas of th e screen. User can contro l PTZ direction, zoom, and focus by click ...

  • EverFocus 264x2 - page 43

    36 4 . 1 3 S E A R C H By mouse: Righ t-click to bring up the menu bar and click to enter Search Menu . By front pane l: Press ” Search ” key to enter Search Menu directly. 4. 13. 1 T i me S ea r c h Figure 4- 5 Search Menu – T ime Search Play From : Select the time to be searched by choo sing the Date and Time. Click on the “Play” butto ...

  • EverFocus 264x2 - page 44

    37 4. 13. 2 E v en t S ea r ch Figure 4- 6 Search Menu – Even t Search From: Select starting date and time To: Select end ing date and time. Camera: Select which cameras to search for. Event: Sele ct which event type(s) to search for. Choose f rom Alarm, Motion, Video Loss, or Others. Click on the “Search” but ton to start search ing. The sea ...

  • EverFocus 264x2 - page 45

    38 Prev Page : Go to previous page. Next Page : Go to next page Unlock : Unlo ck the item if the item is locked Lock : Lock the item (After click Lock button, the selec ted item will show Locked or Partia l) Delete : De lete item if it is not locked Play : Playback selected item Copy : Copy select ed item In Lock status, there will sh ow “Partial ...

  • EverFocus 264x2 - page 46

    39 Figure 4- 7 Search Menu – Motion Search From: Select motion search starting date/time. To: Select mot ion search ending date/time. Camera: Select camera number to be searched. Figure 4- 8 Search Menu – Set Grid Grid Setting: ...

  • EverFocus 264x2 - page 47

    40 Choose which area s of the motion grid will be included in the search. The areas you set in motion search must also be active in the motion settings of the Camera Setting Menu . Use the mouse to drag your desire d area. Press “ Set All ” b utton to select the entire area. Press “ Clear All ” to de select the entire a rea. Press “ Save ...

  • EverFocus 264x2 - page 48

    41 Archive To: Sele ct whether you want to copy to USB or DVD. Data Size: Shows the estimated total size for the selected time period . (Paragon DVR is L inux base DVR, when you chec k the space of USB sticker by DVR or PC, t he space may have a little bit differen t between PC and DVR) Archive Now : Press “ Archive ” button to start archiving. ...

  • EverFocus 264x2 - page 49

    42 5 D V R C O N F I G U R A T I O N This chap ter will wa lk you thro ugh the DVR Men u Settings step b y step and sho w yo u how to se t the DVR for your specific app lication. 5 . 1 C O N F I G U R A T I O N M E NU 1. To bring up the Main Menu, press the “ Menu/Esc ” key on the front panel or right-click with the US B mouse to bring u p the ...

  • EverFocus 264x2 - page 50

    43 Date: Set the current date of DVR. Time: Set the cu rrent time of DVR. Resolution: Sele ct recording resolution based on vid eo format. NTSC: 704 x480 / 704x240 / 352x240 PAL: 704x576 / 704x288 / 352x288 Record Mode: Blank: No change for Record mode Normal+Event : Normal recording plus event recording . Event Only: Event recording only. Schedule ...

  • EverFocus 264x2 - page 51

    44 DHCP: DHCP server in LAN will automatically assign IP fo r network connection. PPPoE: IP Addres s: This field shows th e current IP Address for the DV R. A Fixed IP address must be se t manually. If DHCP or PPPo E is selected, this value will be assig ned automatically. Subnet Mask : This field shows the subnet mask for your n etwork so the DVR ...

  • EverFocus 264x2 - page 52

    45 5 . 3 C A M ER A S E TT I N G Figure 5-2 is a screen sh ot of the CAMERA SETTING MENU . This menu is u sed to configure individual camera set tings. Figure 5- 2 Camera Menu -Basic Setting 5. 3.1 Bas ic Set ti n g Camera: Select the camera number. Title: The title setting allows you to assign a title to selected camera. Each title supports up to ...

  • EverFocus 264x2 - page 53

    46 Covert: Check t he box to hide the ca mera picture in live and se quence modes. However, th e image will still be recorded and can be played back by any use r who has playback rights. Record Mode: 2 record modes are available. Normal + Event: Th is recording mode includes continuous and event recording. Event Only: Video will be recorded only wh ...

  • EverFocus 264x2 - page 54

    47 5. 3.2 Vi de o A dj us t Figure 5- 3 Camera Men u – Video Adjust Camera: Select the camera you wish to adjust. “Title” will cha nge to the name of the sele cted camera. Brightness: Ad justs how bright/dark the picture appears. If details appear to be lost in the shadows or darker regions, try increasing the Brightness. If the image appears ...

  • EverFocus 264x2 - page 55

    48 5. 3.3 Mo t io n Figure 5- 4 Camera Men u – Motion Camera: Select the camera you wish to adjust. “Title” will cha nge to the title name of the sele cted camera. Enable: Chec k box to enable motion detection. Other motion options will not be available unless this feature is sele cted. Log: Check bo x to record motion events in the log. Main ...

  • EverFocus 264x2 - page 56

    49 Auto Lock: Check the box an d the events will be recorded in the write protec ted segment of the Hard Disk. (DVR will lock a pe riod of time when alarm happen, the length of time will depend on DV R setting) Alarm Output: This will tran smit a signal through o ne of t he alarm outputs. It can b e set to eith er “ NONE ” (not active), “ 1 ? ...

  • EverFocus 264x2 - page 57

    50 Figure 5- 5 Camera Menu – Motion Grid Settin g Apply To: This b utton can be used to copy the motion se ttings to other cameras. Select which cameras you wish to copy to. "Select All" selects all cameras, “Unselect All” d eselects all cameras. Click “OK” to copy the settin gs or "Cancel" to exit without copying. ...

  • EverFocus 264x2 - page 58

    51 5. 3.4 Vi de o L os s Figure 5- 6 Camera Menu – Video Loss Camera: Select the camera you wish to adjust, “Title” will cha nge to the title name of the sele cted camera. Enable: Check box to enable Video Loss. Log: Check bo x to record video loss events in the log. Pre-alarm Record: Check box to record severa l moments before the video loss ...

  • EverFocus 264x2 - page 59

    52 Apply To: This button can be u sed to copy the vid eo loss sett ings to o ther cameras. Select which cameras you wish to copy to. "Select All" selects all cameras, “Unselect All” d eselects all cameras. Click “OK” to copy the settin gs or "Cancel" to exit without copying. 5 . 4 R E C OR D & P L A Y S E T TI N G Fi ...

  • EverFocus 264x2 - page 60

    53 For Schedule recording, t he o nly wa y to stop schedule recording is to turn schedule recordin g off. Pressing any keypad on fron t panel to change schedule recording will n ot work during scheduling record mode. When schedu le recording is disabled, DVR will auto turn on recording Time Stam p: Select if the time and date will display while rec ...

  • EverFocus 264x2 - page 61

    54 5. 4.3 Pl ay Figure 5- 9 Record & Play Menu - Play Quick Playback: Ch eck the box to enable quick playback funct ion. Playback From X Seconds ago: When the DVR is put int o playback, it will begin playing from the select ed time. Choo se from 60 to 3600 seconds. ...

  • EverFocus 264x2 - page 62

    55 5 . 5 A L A R M & EV E N T S E T T I N G Figure 5-10 is a screen shot of th e ALARM & EV ENT SETTI NG MENU . This menu will walk you th rough alarm and event setup. Figure 5- 10 Alarm & Event Menu - Alarm 5. 5.1 Al ar m Alarm: Sele ct the alarm number from 1 to 16. Enable: Check box to enable alarm. Log: Check bo x to record alarm ev ...

  • EverFocus 264x2 - page 63

    56 Recording: Se lect which cameras will start record ing when alarm happens. Email Notify: Check box to enable email notification when an alarm occurs. Input Type: This fie ld is to change the type of alarm trigg er. N.O.: Normal Open contact. N.C.: Normal Close contact. Network Alarm: Check box to send out a ne twork alarm to clien t PC when moti ...

  • EverFocus 264x2 - page 64

    57 5. 5.2 Ev en t This section cov ers internal system event warn ings. Figure 5- 11 Alarm & Event Menu – Event Event: Sele ct from the following event types. Fan Failure: The internal fans are equipped with rotation detection. Any fault of a fan will cause "Fan Failure" event. HD Temperatu re: Hard drive is over the safety warning ...

  • EverFocus 264x2 - page 65

    58 Fan Failure : Figure 5- 12 Alarm & Event Menu – Event-Fan Failure Log: Check bo x to record events in the log. Buzzer: Check box to enable buzzer when a fan fails t o w ork. Email Notify: Check box to enable email notification when a fan fails to work. Network Alarm: Check box to send out a n etwork alarm to clien t PC. (requires Powe rCon ...

  • EverFocus 264x2 - page 66

    59 HD Temperature : Figure 5- 13 Alarm & Event Menu – Event - HD Te mperature Log: Check bo x to record events in the log. Buzzer: Check box to enable buzzer when hard drive’s temp erature is over the “Temp. Warning Limit” . Email Notify: Check box to enable email notification when temperature is over the “Temp. Warnin g Limit”. Net ...

  • EverFocus 264x2 - page 67

    60 HD Failure: Figure 5- 14 Alarm & Event Menu – Event - HD Fa ilure Log: Check bo x to record events in the log. Buzzer: Check box to enable buzzer when no hard d rive is detected. Email Notify: Check box to enable email notification function when HD fails. Network Alarm: Check box to send out a n etwork alarm to clien t PC. (requires Powe r ...

  • EverFocus 264x2 - page 68

    61 HD Full: Figure 5- 15 Alarm & Event Men u – Event - HD F ull Buzzer: Check box to enable buzzer when hard drive is full. Email Notify: Check box to enable email notification when HD is full. Network Alarm: Check box to send out a n etwork alarm to clien t PC. (requires Powe rCon software and setting up Alarm S erver in Network Setup menu) ...

  • EverFocus 264x2 - page 69

    62 HD Off: Figure 5- 16 Alarm & Event Menu – Event - HD Off Buzzer: Check box to enable buzzer when hard drive is off. Email Notify: Check box to enable email notification when HD is off. Network Alarm: Check box to send out a n etwork alarm to clien t PC. (requires Powe rCon software and setting up Alarm S erver in Network Setup menu) Alarm ...

  • EverFocus 264x2 - page 70

    63 Power Loss: Figure 5- 17 Alarm & Event Menu – Event – Po wer Loss Log: LOG is pe rmanently checked for this featu re. Power Loss events are always recorded by the DVR. Email Notify: Check box to enable email notification when HD is off. Network Alarm: Check box to send out a n etwork alarm to clien t PC. (requires Powe rCon software and ...

  • EverFocus 264x2 - page 71

    64 Record Stop: Figure 5- 18 Alarm & Event Menu – Event – Recor d Stop Log: Check bo x to record events in the log. Buzzer: Check box to enable buzzer when DVR stops recording. Email Notify: Check box to enable email notification when DVR stops recording. Network Alarm: Check box to send out a n etwork alarm to clien t PC. (requires Powe rC ...

  • EverFocus 264x2 - page 72

    65 Network Loss : Figure 5- 19 Alarm & Event Menu – Event – Networ k Loss Log: Check bo x to record events in the log. Buzzer: Check box to enable buzzer when network is lost. Alarm Output: This will tran smit a signal through o ne of t he alarm outputs. It can b e set to eith er “ NONE ” (not active), “ 1 ”, “ 2 ” , “ 3 ”, ...

  • EverFocus 264x2 - page 73

    66 5 . 6 S C H ED UL E SE T T I N G Figure 5- 20 is a screen shot o f the SCHEDULE S ETTING MENU . In this menu you can set a uniqu e timer to start re cording du ring a specified time p eriod. This menu is used to conf igure Express Setup, Ho lidays and Schedule settings. Figure 5- 20 Schedule Menu- Express Setup 5. 6.1 Ex pr e s s Set up Weekend ...

  • EverFocus 264x2 - page 74

    67 Event Action: Check this box to enable Bu zzer, A larm ou t, E-mail and Network act ions when an event occurs on the se lected time period. Apply: Press A pply butt on b ring up a co nfirmation window. Select “Yes” to co nfirm and apply express schedule se ttings or “No” to cancel changes. 5. 6.2 Ho li day s In addition to setting a week ...

  • EverFocus 264x2 - page 75

    68 Month/weekday: Repeats recording on a specific day of the month/week. Details: Specif ies the date to be recorded. Prev: Previous Page (30 Holidays Total) Next: Next Page (30 Holidays Total) 5. 6.3 Sc he d ul e Figure 5-22 Schedule Menu-Schedule Camera: Select a nu mber to change the schedule for that camera. Each ca mera can be set on a 24 hour ...

  • EverFocus 264x2 - page 76

    69 2. Change the section to different mode (with differen t co lor) b y clicking o n t he first block of e ach section. The color s watches from gray -> orange -> blue, every time user clicks the first block of a section. Schedule Se tting from front panel 1. Enter schedule setting mode : press Enter button to e nter schedu le setting mode. A ...

  • EverFocus 264x2 - page 77

    70 6. Editing blocks i n a time bar : when a time bar is select ed (highlighted in re d frame ), press Enter button, t hen the first b lock of t his b ar will b e selected (hig hlighted in blue frame). Tu rning Jog knob to switch to desired block as starting time, and press Ente r button again to confirm. At this time, the current a nd all followin ...

  • EverFocus 264x2 - page 78

    71 Press “ Edit Timezone ” but ton to edit the time zone . Figure 5- 23 Schedule Menu- Schedule-Edit Tim ezone Editing Timezone : From: Displays sche dule start time To: Displays schedule end time Record: Displays Re cord mode Resolution: Sele ct recording resolution. NTSC: 704x480; 704x240; 352x240 PAL: 704x576, 70 4x288, 352x288 Normal: Frame ...

  • EverFocus 264x2 - page 79

    72 Apply to Ca meras: This button can b e used to copy schedules to other cameras. Se lect which cameras you wish to copy to. "Select All" selects a ll cameras, “Clear All” dese lects all cameras. Click “ OK” t o cop y the settings or "Ca ncel" to exit without copying. ...

  • EverFocus 264x2 - page 80

    73 5 . 7 N E T W OR K S ET T I NG Figure 5-24 is a screen shot of the NETWORK SETTING MENU . This menu is for configuring the DVR fo r a network connectio n. NOTE: Since every Network Configu ration is different, please check with your Network Administrat or or ISP to see if your DVR requires specific IP addresses and/or port numbers. Figure 5- 24 ...

  • EverFocus 264x2 - page 81

    74 HTTP Port: Port numb er for HTTP/WEB commun ication. Bandwidth Limit: Allows user to limit the bandwidth u sed by the DVR. 5. 7.2 EM AI L Figure 5- 25 Network Menu – Email SMTP Server : Assign the SMTP (e-mail) server’s name. NOTE: For more re liable email service, use the server’s IP add ress. SMTP Port: Assign the port number used by the ...

  • EverFocus 264x2 - page 82

    75 5. 7.3 DDN S DDNS Server: Select eith er “EverfocusDDNS” or “www.dyndns.org” as the DDNS p rovider. If DDNS will not be used , simply select “Disable”. Everfocus DDNS Figure 5- 26 EverfocusDDNS DVR Name: Inpu t the desired name for the DVR Register/Upda te: Click the button to submit and reg iste r the name to the Everfocus server. ...

  • EverFocus 264x2 - page 83

    76 www.dyndns .org Figure 5- 27 www.dyndns.org Host name: Host name created through the dyndn s account. User name: User n ame of the dyndns account. Password: Pa ssword of the dyndns account. Confirm : Re-ent er password. Note: For more de tails on DDNS setup, please see “Chapter 8 - Everfocus DDNS Setup”. ...

  • EverFocus 264x2 - page 84

    77 5. 7.4 Al ar m Se r v er Figure 5- 28 Network Menu – Alarm Server Server IP1~3 : IP address of client PC with installed PowerCon S oftware. The network alarm can be transmitted to up to 3 addresses. Protocol: Sele ct the protocol type for alarm transmission: UDP: User Datagra m Protocol TCP: Transmission Control Protocol Port: Select the trans ...

  • EverFocus 264x2 - page 85

    78 5 . 8 D I S PL A Y S ET T I NG Figure 5-29 is a screen shot o f the DISP LAY SETTING MENU . This menu will wa lk yo u through Monitor On-Screen Display (OSD) and Sequential setup. Figure 5- 29 Display Menu – M onitor OSD 5. 8.1 Mo ni t o r O SD These are the display options for the Main Monitor. Main Monitor Camera Ti tle: Check the box to dis ...

  • EverFocus 264x2 - page 86

    79 5. 8.2 Ma i n M / T SE Q Figure 5- 30 Display Menu – M ain M/T SEQ Step: Sequen ce order. Cannot be changed. Camera: Select which camera appears on the curren t step. Dwell (sec): Se t the dwell time for each step. Sequence d well time can be set from 0 to 99 second s. 5. 8.3 Cal l M /T S EQ Figure 5- 31 Display Menu – Ca ll M/T SEQ Step: Se ...

  • EverFocus 264x2 - page 87

    80 5 . 9 D I S K S E T T I N G Figure 5-32 is a screen shot of the DIS K SETTING MENU . This menu is use d to review and manage th e DVR’s hard d rive settings. Figure 5- 32 Disk Menu 5. 9.1 Di sk Disk: Select the disk n umber. Health Status: Disp lays current status of the selected disk. Disk Tem perature: Displays current disk temperatu re. Dis ...

  • EverFocus 264x2 - page 88

    81 5. 9.2 Loc k/F or ma t Figure 5- 33 Lock/Form at Menu Maximum Lock (%): User c an set the maximum lock pe rcentage of the HDD volume. After setting lock percentage, it can be enabled/disabled in three places 1. “Camera > Basic Se tting > Motion > Auto Lock” 2. “Alarm & Event > A larm > Auto Lock”. 3. Lock or unlock the ...

  • EverFocus 264x2 - page 89

    82 Note : the followin g rules apply to Hot Swappable model on ly 1. If user takes out the HDD and put it back (with the same HDD) to the same DVR. It will be fine. 2 . If user takes ou t the HDD-A of Paragon-A, then put it into another Paragon-B which alread y has a HDD-B. The data of HDD-A will be cleaned in Paragon-B. If user hopes to keep the d ...

  • EverFocus 264x2 - page 90

    83 5 . 1 0 SY S T E M S E T T I N G Figure 5-34 is a screen shot of the S YSTEM SE TTING MENU . Th is menu is for se tting up the syst em configuration s of the DVR. Figure 5- 34 System Menu – Date/Time 5. 10. 1 D at e/T i m e Date: Set current Date. Time: Set curren t Time. Date Format: Cho ose date format from yyyy/mm/dd, dd/mm/yyyy, an d mm/dd ...

  • EverFocus 264x2 - page 91

    84 5. 10. 2 D ay l i gh t S av i n g Figure 5- 35 System Menu – Daylight Saving Daylight Saving: Ch eck the box to enable daylight sa ving time. Start Date: Set the start date of daylight saving time. Start Time (hh:mm): S et the time when daylight saving time begins. Set To (hh:mm): This is wh at the time will chang e to when daylig ht saving be ...

  • EverFocus 264x2 - page 92

    85 5. 10. 3 U s er User Menu is where you can add or delete different users on the system as well as set administrato r rights. Figure 5- 36 System Menu – Use r Add Click “Add” b utton to add a new use r. Set the na me (case-sensitive), pas sword, and access le vel. Press “Add” button to co nfirm a new user or “Cancel” to exit without ...

  • EverFocus 264x2 - page 93

    86 Edit Click “Edit” butto n to ma ke changes to an e xisting u ser acco unt. P ress “Save ” button to save ch anges o r “Cancel” to exit with out making changes. Figure 5- 38 System Menu – Use r - Edit User Login: Check this box to activate user login. Whe n th is is disabled, no usern ame or p assword is required to acces s the syst ...

  • EverFocus 264x2 - page 94

    87 5. 10. 4 I /O C on t r ol Figure 5-39 is a screen shot of the I/O Contro l Setting Men u. This menu is u sed to define the settings for controlling the DVR through RS232 or RS485. Figure 5- 39 System Menu – I /O Control RS232 Baud Rate : The speed used to t ransmit instruction or informatio n through the RS232 port on t he DVR. Choose from the ...

  • EverFocus 264x2 - page 95

    88 5. 10. 5 M i s c. Figure 5- 40 System Menu – F irmware & Misc. Firmware Current Firmwa re Version: Displays the current version. Firmware Upgrade : Press “Upgrade” to upgrade the firmware. NOTE: To perform a Firmware Upgra de, you will need to connect a US B flash device with the latest version of the f irmware. Do not d isconnect US B ...

  • EverFocus 264x2 - page 96

    89 5 . 1 1 I N F O R M A T I ON SE T TI N G Figure 5- 41 is a screen shot of the INFORMATION SETTING MENU . This menu d isplays important syst em information . Figure 5- 41 Information Menu – System 5. 11. 1 S y st em System Version: Displa ys firmware version number. Model: Displays DVR mo del number. NTSC/PAL: Displays cu rrent video format. Ne ...

  • EverFocus 264x2 - page 97

    90 5. 11. 2 L og Figure 5- 42 Information Menu – Log Log Type: Event: to see log sorted by event. User: to see log so rted by user. Operation: to s ee log sorted by operation. View Log: P ress “View Log” butto n to view the log. See Figure 5- 43 for more detail. Clear Log: Pre ss “Clear Log” button to clear the log. Export Log to USB: Exp ...

  • EverFocus 264x2 - page 98

    91 Figure 5- 43 Log List Prev Page : Go to the previous page of log. Next Page : Go to the next page of log. Clos e: Close the win dow ...

  • EverFocus 264x2 - page 99

    92 6 N e t w o r k i n g O v e rv i e w This ch apter will give you a b asic inst ruction on ho w to set up the DVR for netwo rk connect ion. It is h ighly recommended t hat yo u have a wo rking knowledge of what a netwo rk is a nd h ow it works. This will be helpful in co mpleting the networking process. 6 . 1 I nt ro d u ct i o n t o T C P / I P ...

  • EverFocus 264x2 - page 100

    93 6 . 4 V i r t u a l P o r t s A port number represe nts a " channel" or entryway for ne twork co mmunications. Po rt numbe rs allow different applications on the same co mputer t o utilize network resources without interfering with each ot her. Port numbers most com monly appear in network prog ramming, particularly so cket programming ...

  • EverFocus 264x2 - page 101

    94 Do you have a static IP address? __________ ____ A Static IP address means you use the same IP a ddress every time you connect to the Internet. With a static IP address , other Interne t users a lways know t he address of your location and can easily connect with it. This make s it much simpler to host a website, email server, or other type of s ...

  • EverFocus 264x2 - page 102

    95 6 . 7 S i m pl e O n e to On e C o n n e ct i o n Crossover Ethe rnet Cable Pin outs: The Figure be low shows the pin configurations fo r a cross-over cable. Connection Proc edure:  The First step is to purchase or make a cross-ove r cable. We recommend purchasing one if you have neve r made a cross-over cable. Please remember you can not use ...

  • EverFocus 264x2 - page 103

    96  Assign an IP of 192.168.001 .003, a Subnet Mask of 255. 255.255.000, and a Gateway of 192.168.001.001 . You can ignore DNS Server.  The next step is to set the computer’s n etwork settings t o match those o f t he DVR. You will need Administrato r privileges on your Windows machine to do this.  To assign a fixed IP address in Windows ...

  • EverFocus 264x2 - page 104

    97 ...

  • EverFocus 264x2 - page 105

    98 ...

  • EverFocus 264x2 - page 106

    99  Click on the option that says “Use the following IP ad dress”  Assign an IP addres s of 192.168.1.2 , a Subnet Ma sk of 255.255 .255.0, an d a Default G ateway of 192.168.1.1, the n click OK.  Restart both the co mputer and the DVR.  To access the DVR f rom the computer, simply ope n Internet Explorer and in the address bar type ...

  • EverFocus 264x2 - page 107

    100 6 . 8 D i r e c t H i gh S pe e d M o d e m C o n n e c t i o n Straight Through Ethe rnet Cable Pin outs: The Figure be low shows the pin configurations fo r a straight cable. Connection Proc edure:  The first step is to purchase or ma ke a stra ight through cable. We recommend purchasing one if you have ne ver ma de a straight through cabl ...

  • EverFocus 264x2 - page 108

    101  Once you have a straight throug h cable plug one end into the LA N port o n the back o f the recorder and the other in to the high speed modem.  Log into the Eve rFocus DVR menu and go to the Network Sett ing Menu.  Input the Static IP address, the Subnet Mask, and the Gatewa y that you obtained from the internet service provide r. ? ...

  • EverFocus 264x2 - page 109

    102 6 . 9 R o u t e r o r LA N C on n e ct i on Straight Through Ethe rnet Cable Pin outs: The Figure be low shows the pin configurations fo r a straight cable. Connection Proc edure:  The First step is to purchase o r make a straight through cable. We recommend purchasing one if you have ne ver ma de a straight through cable. Please reme mber y ...

  • EverFocus 264x2 - page 110

    103  Once you have a straight throug h cable plug one end into the LA N port o n the back o f the recorder and the other in to the router.  Log into the Eve rFocus DVR menu and go to the Network Sett ing Menu.  To let the route r automatically assign an address:  Set the Network Typ e to DHCP. Make sure to write do wn the IP address and ...

  • EverFocus 264x2 - page 111

    104 number o f the IP address. For example, if th e IP address of the computer is 192 .168.2.101, the DVR’s IP address should be 192.168.002.050.  To access the DVR f rom a computer simply open I nternet Explorer and in the address bar t ype: http:// (IP address of the DVR)  Note: The DVR’s IP add ress will only wo rk a t t he loca tion o ...

  • EverFocus 264x2 - page 112

    105 7 R E M O T E O P E R A T I O N F R O M B R O W S E R 7 . 1 C O N N E C T I N G T O D V R To access the DVR from a computer, open an Internet Explorer window and in the address bar type: Local connectio n: http:// (IP address from the DVR’s Ne twork Menu) Internet connectio n: http:// (IP address given by you r Internet Service Provider)  ...

  • EverFocus 264x2 - page 113

    106 7 . 2 B R O W S E R S E C U R I T Y S E T T I N G 7. 2.1 Ins ta ll in g A ct iv eX con t r ol s When you first c onnect to the DVR’s IP addre ss, you should see a screen like the one below. If you do not see a yellow bar like the one the arrow is pointing at, your se curity settings may be too high. If so, go to “Section 7.2.2 - Enabling Ac ...

  • EverFocus 264x2 - page 114

    107 Install the ePlus DVR.cab file when prompted to do so. Once the file fin ishes installing, you will return to the same login page as before. Type in the use rname and password and click Login to view the cameras. Default username: admin Default passwo rd: 11111111 ...

  • EverFocus 264x2 - page 115

    108 7. 2.2 En ab l i ng A ct iv eX C o nt r o ls Note: This section is only necessary if you DO NO T see the yellow ActiveX bar at the top of your browse r screen when you first connect to the DVR. At the top of the Internet Explorer Window, click on Tools, then select Internet Options. Click the Se curity tab at the top of the window, then ch oose ...

  • EverFocus 264x2 - page 116

    109 In the Security Set tings window, scroll to “ActiveX con trols and plug-ins” Set the cont rols as follows: “ Enable ”:  Allow previou sly unused ActiveX controls to run withou t prompt ( Internet Explorer 7 on ly )  Allow scriptlets ( I E7 only )  Automatic promp ting for ActiveX controls  Binary and scrip t behaviors  Di ...

  • EverFocus 264x2 - page 117

    110 Close the window so you are back at the login screen. Click the Refre sh button to reload the page. Install the ePlus DVR.cab file when prompted to do so. Once the file fin ishes installing, you will return to the same login page as before. Type in the use r name and password and click Lo gin to view the cameras. Default user name : admin Defau ...

  • EverFocus 264x2 - page 118

    111 7 . 3 R E M O T E L IV E V I E W 1. In the main page, you will see live images in a 16-screen disp lay (or 8 screens, depending on t he model). 2. The status of each camera is represented by different colors o n the left side of the screen. Green means normal; o range indicates a Motion; blue indica tes Vloss, red indicates an alarm even t. Cli ...

  • EverFocus 264x2 - page 119

    112 7 . 4 R E M O T E P T Z C O N T R OL 1. Use Direction A rrows (up, down, left, right) to mo ve the camera to the desired direction and a ngle. 2. In Zoom option , Click “ Z+” to zoom closer or “ Z-” to zoom fa rther away. 3. In Focus op tion, click “ F+ ” to increa se the focus or click “ F- ” to d ecrease the focus. 4. In Iris ...

  • EverFocus 264x2 - page 120

    113 a. Click “ Tour ” button b. Click the nu mber of the desired tour c. Click “ Go ” butto n 12. Steps to remove a tour a. Click “ Tour ” button b. Click the nu mber of the desired tour c. Click “ Delete ” butto n ...

  • EverFocus 264x2 - page 121

    114 7 . 5 R E M O T E P L A Y B A C K To play back the video, press “Search” bu tton. Sele ct f rom “Time Sea rch”, “Event Search”, o r “Motion Search”. For more details about Search setting, please refer t o “4.13 Search Setting”. “Event Search ” and “M otion S earch” will show maximum 40 0 search result items(near sta ...

  • EverFocus 264x2 - page 122

    115 8 E V E R F O C U S D D N S S E T U P Setup Steps: Step 1. S et up the Network Menu according to the instructions det ailed in the Ne tworking chapter. (Make sure that DNS Server 1 is set correctly or DDNS will not work) Step 2. Go t o the website http://everfocusddns .com and check for an available name. Note: This step is optional, a s it is ...

  • EverFocus 264x2 - page 123

    116 9 L I N K S Y S & D - L I N K P O R T F O R W A R D I N G 9 . 1 L IN K S Y S P O R T FO R WA R D I N G This section will co ver a few simple configurations for the Linksys router. Th is chapt er is only to offer some help to the installer a nd end user. P lease understand we DO NO T support this product and will not give tech support on it. ...

  • EverFocus 264x2 - page 124

    117 Applications a nd Gaming allows yo u to set up public services on your network, such as web servers, ftp servers, e-mail servers, or o ther specialized Internet applications. (Some Internet applications may not require any forwarding) To fo rward a port, ente r the information on each line for the criteria require d. Descriptions of each criter ...

  • EverFocus 264x2 - page 125

    118 9 . 2 D - L IN K P O R T F O R W A R D I N G This section will cover a few simple configu rations fo r the D-L ink router. This chapter is only to offer some help to the installer a nd end user. P lease understand we DO NO T support this product and will not give tech support on it. If you need additional techn ical support on this router you m ...

  • EverFocus 264x2 - page 126

    119 Click Virtual Se rvers on the left to bring up the fo llowing screen. Virtual Se rvers allows users who are connecting re motely to access services on the route r’s Local Network. The functions o f each field are described below. Virtual Server - S elect Enabled or Disabled Name - Enter the name referencing the virtual service Private IP - Th ...

  • EverFocus 264x2 - page 127

    120 Here is an exa mple of the information for each service: Name Private IP Protocol Private Port Public Port Schedule HTTP 1 92.168.1.50 Both 80 80 En able CTRL 1 92.168.1.50 Both 1600 1600 Enable  Note: If you changed port 80 in the DVR’s Network Menu, open that port instead of 80. ...

  • EverFocus 264x2 - page 128

    121 1 0 T R O U B L E S H O O T I N G If you ha ve problems with the system, run through the fo llowing checklist to see if you can solve the problem.  The DVR w ill not go into record mode.  Bring up the DVR’s Menu and check un der the Ca mera Menu. Verify that all co nnected cameras are checked as “Installed” and that Record Mode is s ...

  • EverFocus 264x2 - page 129

    122 A P P E N D I X A : T I M I N G O F A L A R M M O D E S Transparent Mo de Input Event Alarm Duration t t Event = t Reaction t Event : Duration of a larm input source (motion, contact, system events...) t reaction : Resulting duration for this alarm mod e, related to event record, alarm outputs, OSD message, buzzer Timeout + Transp arent Mode t ...

  • EverFocus 264x2 - page 130

    123 Timeout Mode t Input Event Alarm Duration t Duration = t Reaction t Event t Event : Duration of a larm input source (motion, contact, system events...) t Duration : Alarm duration f or timeout, defined in the event setup menu s t reaction : Resulting duration for this alarm mod e, related to event record, alarm outputs, OSD message, buzzer Perm ...

  • EverFocus 264x2 - page 131

    124 Timeout Mode: Retrigger of Alarms t Event : Duration of a larm input source (motion, contact, system events...) t Duration : Alarm duration f or timeout, defined in the event setup menu s t reaction : Resu lting duration for this alarm mod e, related to event record, a larm outputs, OSD message, buzzer Timeout+Tran sparent Mode: Retrigger of Al ...

  • EverFocus 264x2 - page 132

    125 A P P E N D I X B : C H A N G I N G R U L E F O R E X P R E S S S E T U P Case 1: Record Mode: Normal + Event Record With: Recording days DVR wil l Auto adjus t Quality and E vent frame ra te to match the Recording days which user selected: According to resolution, event hours and assumption above, DVR will select one set of suitable quality a ...

  • EverFocus 264x2 - page 133

    126 Case 3: Record Mode: Normal + Event or Event Only Record With: Preset Setting DVR will apply se tting in below table to all camera s according to different Preset Setting. Preset Sett ing Option Camera Item Apply value Quality Superior Normal Fram e Rate Max recordi ng frame rate of DVR Best Quali ty Event Fra me Rate 30 Quality Standard Normal ...

  • EverFocus 264x2 - page 134

    127 Headquarte r Office 12F, No.79 Sec.1 Shin- Tai W u Road, Hsi-Chi, Tai pei, Taiwan Tel: +886-2- 26982334 Fax: +886-2-2 6982380 Beijing office Room 609,T echnolog y Trade Build ing. Shangdi Inf ormation Indus try Base, Haidian Distr ict,Beijing Ch ina Tel: +86-10- 62971096 Fax: +86-10-6 2971423 European O ffice Albert-Einste in-Strass e 1, D-4644 ...

Manufacturer EverFocus Category DVR

Documents that we receive from a manufacturer of a EverFocus 264x2 can be divided into several groups. They are, among others:
- EverFocus technical drawings
- 264x2 manuals
- EverFocus product data sheets
- information booklets
- or energy labels EverFocus 264x2
All of them are important, but the most important information from the point of view of use of the device are in the user manual EverFocus 264x2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals EverFocus 264x2, service manual, brief instructions and user manuals EverFocus 264x2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product EverFocus 264x2.

A complete manual for the device EverFocus 264x2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use EverFocus 264x2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of EverFocus 264x2.

A complete EverFocus manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual EverFocus 264x2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the EverFocus 264x2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the EverFocus 264x2, that we can find in the current document
3. Tips how to use the basic functions of the device EverFocus 264x2 - which should help us in our first steps of using EverFocus 264x2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with EverFocus 264x2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of EverFocus 264x2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning EverFocus 264x2?

Use the form below

If you did not solve your problem by using a manual EverFocus 264x2, ask a question using the form below. If a user had a similar problem with EverFocus 264x2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)