English dropdown-ico

Manual Q-Logic 2300 series

62 pages 0.38 mb
Download

Go to site of 62

Summary
  • Q-Logic 2300 series - page 1

    CF2351102-00 F Page i Q Simplify SANblade 2300 Series User ’ s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters ...

  • Q-Logic 2300 series - page 2

    SANblade 2300 Series User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters Q Page ii CF2351102-00 F Information fu rnished in this manual is believed to be accurate and reliab le. However , QLogic Corporation assumes no responsibility for its use, nor for any infringements of patent s or other rights of third part ies which may resul ...

  • Q-Logic 2300 series - page 3

    CF2351102-00 F Page iii Table of Contents Section 1 Introduction 1.1 How to Use this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.3 What is Fibre Channel? . . . . . . . . . . . . . . . . . . . . ...

  • Q-Logic 2300 series - page 4

    SANblade 2300 User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters Page iv CF2351102-00 F Q 3.3 Removing the QCP2340/2342 HBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 3.4 FCode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 3.4.1 Updating FCode on the ...

  • Q-Logic 2300 series - page 5

    CF2351102-00 F Page v Q SANblade 2300 User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Ad apters Part II Software Section 6 Solaris SPARC Driver Installation 6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 6.2 Pre-installation Requirements . . . . . . . . . . . . . . . ...

  • Q-Logic 2300 series - page 6

    SANblade 2300 User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters Page vi CF2351102-00 F Q Notes ...

  • Q-Logic 2300 series - page 7

    CF2351102-00 F 1-1 Section 1 Introduction 1.1 How to Use this Guide The SANblade QLogic host bus a dapters (HBAs) supported in this document are described in the following p aragraphs. They are collectively referred to as the QCP/QSB23xx HBA unless otherwise noted. The QCP23 xx HBAs are all 64-bit PCI to Fibre Channel optical media. The QS B23xx HB ...

  • Q-Logic 2300 series - page 8

    1 – Introduction Features 1-2 CF2351102-00 F Q interface for intermediate dist ances (less than 500 meters at the data ra te of 1 Gbps; less than 300 meters at the dat a rate of 2 Gbps). With increased connectivity and performanc e, Fib re Channel is the technology preferred and used by system designers. 1.4 Features ■ Compliance with the follo ...

  • Q-Logic 2300 series - page 9

    CF2351102-00 F I-1 Part I Hardware This part of the SANblade 2300 User ’s Guide describes the host bus a dapters (HBAs) and how to install and configure them. See the section that co rresponds to your HBA. Section 5 contains troubleshoot ing information. HBA Section QCP2330/2332 2 QCP2340/2342 3 QSB2340/2342 4 ...

  • Q-Logic 2300 series - page 10

    I – Hardwa re I-2 CF2351102-00 F Q Notes ...

  • Q-Logic 2300 series - page 11

    CF2351102-00 F 2-1 Section 2 QCP2330/2332 2.1 QCP2330/2332 HBA Component s Figure 2-1 identifies the QCP2330/2332 HBA compo nents referenced throughout this section. Each QCP2330/2332 HBA has a unique serial number , located on the back of the HBA. T ake a minute to write down th e serial number of the QCP2330/2332 HBA in the unlikely event that th ...

  • Q-Logic 2300 series - page 12

    2 – QCP2330/2332 Installation and Removal 2-2 CF2351102-00 F Q 2.1.2 Jumpers Jumpers J1 (QCP2332) and J2 on the QCP2330/2332 HBA determine the defau lt state of connectors J5 (QCP2332) an d J6, respectively . The jumpers are set at the factory with a jumper plug on pins 2–3, which enables the connectors. CAUTION! Changing the jumper settings ca ...

  • Q-Logic 2300 series - page 13

    2 – QCP2330/2332 Installation and Removal CF2351102-00 F 2-3 Q 2.2.2 Inst allation in the Computer (Hot Swap) Perform the following steps to inst all the QCP2330/2332 HBA without shutting down the system (hot swap). See section 2.2.1 for st andard installation instruct ions. 1. Log on to the system as a superuser . 2. At the prompt (#), type the ...

  • Q-Logic 2300 series - page 14

    2 – QCP2330/2332 Installation and Removal 2-4 CF2351102-00 F Q 4. T ype the cfg adm command (see step 2 ) to verify that the system recognizes the QCP2330/2332 HBA and that the HBA is not configured. In the following example, the QCP2330/2332 HBA h as been installed in slot 4 and is not configured. 5. T ype the following commands to configure the ...

  • Q-Logic 2300 series - page 15

    2 – QCP2330/2332 FCode CF2351102-00 F 2-5 Q 6. Connect the appropriate cables from the devices to the J5 (QCP2332) and J6 connectors. 7. Check the QCP2330/2332 HBA hot swap LED1; it should be off , indicating that the HBA is active. See section 6 for detailed instructions on how to install the sof tware driver . If you need FCode, see section 2.4 ...

  • Q-Logic 2300 series - page 16

    2 – QCP2330/2332 FCode 2-6 CF2351102-00 F Q 3. Set the QCP2330/2332 HBA loop ID (see sect ion 2.4.3) . 4. Select the boot device (see section 2.4.4) . 5. Build the bootable disk (see section 2.4.5) . 2.4.1 Up dating FCode on the QCP2330/2332 HBA If you need to update the FCode on th e QCP2330/2332 HBA, use the QLogic qla2x00 flash utility . A QLo ...

  • Q-Logic 2300 series - page 17

    2 – QCP2330/2332 FCode CF2351102-00 F 2-7 Q The new connection mode displays. F or example: Calculating NVRAM checksum, please wait... Current HBA connection mode: 0 - Loop Only Possible connection mode choices: 0 - Loop Only 1 - Point-to-point only 2 - Loop preferred, otherwise point-to-point 2.4.3 Setting the QCP2330/2332 HBA Loop ID When the Q ...

  • Q-Logic 2300 series - page 18

    2 – QCP2330/2332 FCode 2-8 CF2351102-00 F Q 2. Select the QCP2330/2332 HBA att ached to the Fibre Channel device from which you want to boot. For example, type the following at the ok prompt: ok " /pci@1f,0/pci@1/QLGC,qla@4" select-dev 3. Use the show-children co mmand to view the devices attached to the QCP2330/2332 HBA. For example: o ...

  • Q-Logic 2300 series - page 19

    2 – QCP2330/2332 FCode CF2351102-00 F 2-9 Q T o build a boot able disk, perform the following steps: 1. Determine the amount of disk space us ed/available on your current boot disk. Use the df command for a listing. For example: /usr/bin/df -k -l This df example shows that the current boot disk is /dev/dsk/c0t0d0s(x). There are two partitions of ...

  • Q-Logic 2300 series - page 20

    2 – QCP2330/2332 FCode 2-10 CF2351102-00 F Q d. At the partition prompt, t ype print . The partition t able displays, as in the following example. e. At the partition prompt, t ype label . Enter the label. f. At the label prompt, type q uit . g. T ype quit until the system prompt displays. 3. T o create the file system, use the newfs command. For ...

  • Q-Logic 2300 series - page 21

    2 – QCP2330/2332 FCode CF2351102-00 F 2-11 Q 10. Shut down the system. T ype the following: /sbin/init 0 1 1. Boot from the newly created boot disk. For example: boot /pci@1f,0/pci@1/QLGC,qla@4/sd@82,0 NOTE: The target device ID ( sd@82 ) is in hexadecimal. The decimal value is used in step 3 . 12. V iew the current dump device setting. For examp ...

  • Q-Logic 2300 series - page 22

    2 – QCP2330/2332 Specifications 2-12 CF2351102-00 F Q T able 2-1 lists t he values to enter and their corresponding dat a rates. 2.5 S pecifications T ables 2-2 and 2-3 define the QCP2330/2332 specifications. T able 2-1. Fibre Channel Data Rates Va l u e Data Rate 0 One gigabit 1 T wo gigabit s 2 Auto-negotiated rate T able 2-2. QCP2330/2332 Boar ...

  • Q-Logic 2300 series - page 23

    2 – QCP2330/2332 Agency Certification CF2351102-00 F 2-13 Q 2.6 Label The transceiver on the QCP2330/2 332 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.1 1. The transceiver must be operated under recommended op erating conditions. 2.7 Agency Certification The following sections cont ain a summary of E ...

  • Q-Logic 2300 series - page 24

    2 – QCP2330/2332 Agency Certification 2-14 CF2351102-00 F Q ❑ EN61000-3-2:1995 Harmonic Current Emission ❑ EN61000-3-3:1994 V olt age Fluctuation and Flicker ■ VCCI, Class A ■ AS/NZS 3548, Class A C-tick 2.7.2 Product Safety Requirement s ■ UL, cUL ❑ UL 6095050 ❑ CSA C22.2 No 60950 ❑ Class 1 Laser Product per DHHS 21CFR (J) ■ 73 ...

  • Q-Logic 2300 series - page 25

    CF2351102-00 F 3-1 Section 3 QCP2340/2342 3.1 QCP2340/2342 HBA Component s Figure 3-1 identifies the QCP2340/2342 HBA compo nents referenced throughout this section. Each QCP2340/2342 HBA has a unique serial number , located on the back of the HBA. T ake a minute to write down th e serial number of the QCP2340/2342 HBA in the unlikely event that th ...

  • Q-Logic 2300 series - page 26

    3 – QCP2340/2342 Installation and Removal 3-2 CF2351102-00 F Q 3.1.1 LEDs The QCP2340/2342 LED1 and L ED2 (QCP2342) function as shown in tabl e 3-1 . In a standa rd installation, LED3 is of f, i ndicating that the HBA is active. In a hot swap installa tion, LED3 turns blue while the HBA is inserted. If the LED turns o ff, the HBA is inserted and ...

  • Q-Logic 2300 series - page 27

    3 – QCP2340/2342 Installation and Removal CF2351102-00 F 3-3 Q 3. Place the QCP2340/2342 HBA into th e slot. Carefully press the HBA into the slot until it seat s firmly (the switch clicks into a locked position when the HBA is seated). 4. Connect the appropriate cables from the devices to the J2 (QCP2342) and J1 connectors. 5. Power up all exter ...

  • Q-Logic 2300 series - page 28

    3 – QCP2340/2342 Installation and Removal 3-4 CF2351102-00 F Q A list of the system’ s processors, memory , and I/O boats appears, as in the following example. In this example, cP CI slot s 0, 1, 3, and 4 are available. NOTE: If the cPCI slots are not d isplayed, add the following line to the etc/system file: set sghsc:cpci_enable=1 Check the i ...

  • Q-Logic 2300 series - page 29

    3 – QCP2340/2342 Installation and Removal CF2351102-00 F 3-5 Q 4. T ype the cfg adm command (see step 2 ) to verify that the system recognizes the QCP2340/2342 HBA and that the HBA is not configured. In the following example, the QCP2340/2342 HBA h as been installed in slot 4 and is not configured. 5. T ype the following commands to configure the ...

  • Q-Logic 2300 series - page 30

    3 – QCP2340/2342 Removing the QCP2340/2342 HBA 3-6 CF2351102-00 F Q 6. Connect the appropriate cables from the devices to the J2 (QCP2342) and J1 connectors. 7. Check the QCP2340/2342 HBA hot swap LED3; it should be off , indicating that the HBA is active. See section 6 for detailed instructions on how to install the sof tware driver . If you nee ...

  • Q-Logic 2300 series - page 31

    3 – QCP2340/2342 FCode CF2351102-00 F 3-7 Q 3. Set the QCP2340/2342 HBA loop ID (see sect ion 3.4.3) . 4. Select the boot device (see section 3.4.4) . 5. Build the bootable disk (see section 3.4.5) . The QCP2340 has one channel; the QC P2342 has two channels. The code distinguishes between t he channels as follows: ■ qla@4 (QCP2340 and QCP2342 ...

  • Q-Logic 2300 series - page 32

    3 – QCP2340/2342 FCode 3-8 CF2351102-00 F Q The connection mode and options displa y . For example: Current HBA connection mode: 2 - Point-to-point only Possible connection mode choices: 0 - Loop Only 1 - Point-to-point only 2 - Loop preferred, otherwise point-to-point 2. If the connection mode is not correct based on the devices connected to the ...

  • Q-Logic 2300 series - page 33

    3 – QCP2340/2342 FCode CF2351102-00 F 3-9 Q 3.4.4 Selecting the Boot Device Perform the following step s to select a Fibre Channel device that is at tached to the QCP2340/2342 HBA as the boot device : 1. Use the show-devs command to display the device tree for all devices attached to the machine. ok show-devs The device tree displays. The QCP2340 ...

  • Q-Logic 2300 series - page 34

    3 – QCP2340/2342 FCode 3-10 CF2351102-00 F Q 3.4.5 Building the Boot able Disk This procedure assumes that the system is already booted from an existing system hard disk, and that you have alre ady performed a full system backup. The device path on ea ch system differs, depending on the PCI bus slot, t arget ID, LUN, etc. The device name shown in ...

  • Q-Logic 2300 series - page 35

    3 – QCP2340/2342 FCode CF2351102-00 F 3-11 Q a. At the root prompt, type format . b. A list of available hard di sks displays. S pecify th e disk. c. At the format prompt, type partition . d. At the partition prompt, t ype print . The partition t able displays, as in the following example. e. At the partition prompt, t ype label . Enter the label ...

  • Q-Logic 2300 series - page 36

    3 – QCP2340/2342 FCode 3-12 CF2351102-00 F Q 9. Edit the new vfstab file to properly mount the new partition s during boot. In this case, each reference to c0t0 d0s0 is changed to c3t130d0s0. For example: vi /mnt/etc/vfstab 10. Shut down the system. T ype the following: /sbin/init 0 1 1. Boot from the newly created boot disk. For example: boot /p ...

  • Q-Logic 2300 series - page 37

    3 – QCP2340/2342 Specifications CF2351102-00 F 3-13 Q 3.4.6 Setting and Viewing the Fi bre Channel Dat a Rate Use the show-dat a-rate command to view the current QCP2340/234 2 Fibre Channel data rate. For example: ok show-data-rate Current HBA data rate: One Gigabit rate Use the set-data-rat e command to change the current QCP2340/2342 Fibre Chan ...

  • Q-Logic 2300 series - page 38

    3 – QCP2340/2342 Label 3-14 CF2351102-00 F Q 3.6 Label The transceiver on the QCP2340/2 342 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.1 1. The transceiver must be operated under recommended op erating conditions. 3.7 Agency Certification The following sections cont ain a summar y of the EMC/EMI tes ...

  • Q-Logic 2300 series - page 39

    3 – QCP2340/2342 Agency Certification CF2351102-00 F 3-15 Q ❑ EN55022:1995 Class A ❑ Radiated Emission Class A ❑ Conducted Emission Class A ❑ EN55024:1998 ❑ Immunity S t andards ❑ EN61000-4-2 :1995 ESD ❑ EN61000-4-3 :1995 RF Electro Magnetic Field ❑ EN61000-4-4 :1995 Fast T ransient/Burst ❑ EN61000-4-5 :1995 Fast Surge Co mmon/D ...

  • Q-Logic 2300 series - page 40

    3 – QCP2340/2342 Agency Certification 3-16 CF2351102-00 F Q Notes ...

  • Q-Logic 2300 series - page 41

    CF2351102-00 F 4-1 Section 4 QSB2340/2342 4.1 QSB2340/2342 HBA Component s Figure 4-1 identifies the QSB2340/234 2 HBA components referenced throughout this section. Each QSB2340/2342 HBA has a u nique serial number , located on the back of the HBA. T ake a minute to write down the se rial number o f the QSB2340/2342 HBA in the unlikely event that ...

  • Q-Logic 2300 series - page 42

    4 – QSB2340/2342 Installation in the Computer 4-2 CF2351102-00 F Q 4.1.1 LEDs The QSB2340/2342 LED1 and LED2 (QSB2342) function as shown in table 4-1 . 4.1.2 Jumpers Jumpers J7 (QSB2342) and J8 on the QSB2340 /2342 HBA determine the default state of connectors J10 (QSB2342) and J9, respectively . The jumpers are set at the factory with a jumper p ...

  • Q-Logic 2300 series - page 43

    4 – QSB2340/2342 FCode CF2351102-00 F 4-3 Q See section 6 for detailed instructions on how to install the sof tware driver . If you need FCode, see section 4.3 for instructions on how to inst all or update the FCode on the QSB2340/2342 HBA. 4.3 FCode This section provides instructions fo r installing FCode on a QSB2340/2342 HBA installed in a Sol ...

  • Q-Logic 2300 series - page 44

    4 – QSB2340/2342 FCode 4-4 CF2351102-00 F Q 4.3.2 Setting the QSB2340/2342 HBA Connection Mode Perform the following step s to view the current QSB2340/2342 HBA connection mode and change it if necessa ry: 1. Perform step s 1 and 2 in section 4.3.4 . 2. T o view the current connection mode, type the show-connection-mode command. ok show-connectio ...

  • Q-Logic 2300 series - page 45

    4 – QSB2340/2342 FCode CF2351102-00 F 4-5 Q 3. If the loop ID is not correct, chang e it using the set-adapter-loopid command. For example: ok 0 set-adapter-loopid The new loop ID displays. For example: Adapter loopid - 0 4.3.4 Selecting the Boot Device Perform the following step s to select a Fibre Channel device that is at tached to the QSB2340 ...

  • Q-Logic 2300 series - page 46

    4 – QSB2340/2342 FCode 4-6 CF2351102-00 F Q 5. Save the boot device information to the QSB2340/2342 HBA ’s NVRAM. Use the set-boot-id command. Include the selected QSB2340/2342 HBA ’s WWN, loop ID, and LUN. For example: ok 2200002037009eeb 82 0 set-boot-id The following displays: Calculating NVRAM checksum, please wait.... done Boot device lo ...

  • Q-Logic 2300 series - page 47

    4 – QSB2340/2342 FCode CF2351102-00 F 4-7 Q T o build a boot able disk, perform the following steps: 1. Determine the amount of disk space us ed/available on your current boot disk. Use the df command for a listing. For example: /usr/bin/df -k -l This df example shows that the current boot disk is /dev/dsk/c0t0d0s(x). There are two partitions of ...

  • Q-Logic 2300 series - page 48

    4 – QSB2340/2342 FCode 4-8 CF2351102-00 F Q a. At the root prompt, type format . b. A list of available hard di sks displays. S pecify th e disk. c. At the format prompt, type partition . d. At the partition prompt, t ype print . The partition t able displays, as in the following example. e. At the partition prompt, t ype label . Enter the label. ...

  • Q-Logic 2300 series - page 49

    4 – QSB2340/2342 Specifications CF2351102-00 F 4-9 Q 9. Edit the new vfstab file to properly mount the new partition s during boot. In this case, each reference to c0t0 d0s0 is changed to c3t130d0s0. For example: vi /mnt/etc/vfstab 10. Shut down the system. T y pe the following: /sbin/init 0 1 1. Boot from the newly created boot disk. For example ...

  • Q-Logic 2300 series - page 50

    4 – QSB2340/2342 Label 4-10 CF2351102-00 F Q 4.5 Label The transceiver on the QSB2340/2342 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.1 1. The transceiver must be operated under recommended op erating conditions. 4.6 Agency Certification The following sections cont ain a summar y of the EMC/EMI test ...

  • Q-Logic 2300 series - page 51

    4 – QSB2340/2342 Agency Certification CF2351102-00 F 4-11 Q ❑ EN61000-4-5 :1995 Fast Surge Co mmon/Differential ❑ EN61000-4-6 :1996 RF Conducted Susceptibility ❑ EN61000-4-8 : 1993 Power Frequency Magnetic Filed ❑ EN61000-4-1 1: 1994 V olt age Dips and Interrupt ❑ EN61000-3-2:1995 Harmonic Current Emission ❑ EN61000-3-3:1995 V olt age ...

  • Q-Logic 2300 series - page 52

    4 – QSB2340/2342 Agency Certification 4-12 CF2351102-00 F Q Notes ...

  • Q-Logic 2300 series - page 53

    CF2351102-00 F 5-1 Section 5 T roubleshooting 5.1 Problems Af ter Inst allation There are two basic types of inst allation problems that can cause your QCP/QSB23 xx HBA to function incorrectly: hardware problems and Fibre Channel problems. The following section provides it emized checklist s to help you determine why your QCP/QSB23 xx HBA is not fu ...

  • Q-Logic 2300 series - page 54

    5 – Troubles hooting Fibre Channel Problem Checklist 5-2 CF2351102-00 F Q Notes ...

  • Q-Logic 2300 series - page 55

    CF2351102-00 F II-1 Part II Sof t ware This part of the SANblade 2300 User’s Guide describes how to inst all the software drivers for the supported operating systems. See t he section that corresponds to your computer ’s operating system: Before you insta ll the software drivers, you need to locate an d download the appropriate drivers for your ...

  • Q-Logic 2300 series - page 56

    II – Software II-2 CF2351102-00 F Q Notes ...

  • Q-Logic 2300 series - page 57

    CF2351102-00 F 6-1 Section 6 Solaris SP ARC Driver Inst allation (QL2300) 6.1 Introduction This section provides instructions for in stalling the Solaris SP ARC driver in an already installed So laris SP ARC operating system. The naming convention for the drivers, associated files, and messages is QLA; however , the Solaris SP ARC driver supports s ...

  • Q-Logic 2300 series - page 58

    6 – Solaris SPARC Driver Installation Installing the Solaris SPARC Driver from a CD-ROM 6-2 CF2351102-00 F Q qla2300 driver versions 4.1 1 (and earlier) have the following p ackage names: ❑ QLA2300-1 (Solaris 2.6) ❑ QLA2300-2 (Solaris 2.7) ❑ QLA2300-3 (Solaris 2.8 and 9) Checks within the packag e installation will terminate the new driver ...

  • Q-Logic 2300 series - page 59

    6 – Solaris SPARC Driver Installation Installing the Solaris SPARC Dr iver from the QLogic Web Site CF2351102-00 F 6-3 Q 1. Log on to the system as a superuser . 2. Download the driver p ackage from the QLogic W eb site ( www .qlogic.com ) to a directory on the Solaris machine’ s hard disk. 3. At the command prompt, change the directory (cd) to ...

  • Q-Logic 2300 series - page 60

    6 – Solaris SPARC Driver Installation Installing the Solaris SPARC Driv er from the QLogic Web Site 6-4 CF2351102-00 F Q 9. Y ou are prompted to select the directory whe re the driver will be installed. For example: Processing package instance <QLA2300> from </tmpdir/qla2300_pkg> QLogic QLA2300 driver (sparc) Solaris, Rev=X.XX Copyrig ...

  • Q-Logic 2300 series - page 61

    6 – Solaris SPARC Driver Installation FCode CF2351102-00 F 6-5 Q 13. The pkga dd program then installs the SDM library , if selected in step 8 . A script warning is posted, asking whether to continue the in stallation. For example: Processing package instance <QLSDMLIB> from </tmpdir/qla2300_pkg> QLogic SDM Library (sparc) Solaris 7-8 ...

  • Q-Logic 2300 series - page 62

    6 – Solaris SPARC Driver Installation FCode 6-6 CF2351102-00 F Q Notes ...

Manufacturer Q-Logic Category Network Card

Documents that we receive from a manufacturer of a Q-Logic 2300 series can be divided into several groups. They are, among others:
- Q-Logic technical drawings
- 2300 series manuals
- Q-Logic product data sheets
- information booklets
- or energy labels Q-Logic 2300 series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Q-Logic 2300 series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Q-Logic 2300 series, service manual, brief instructions and user manuals Q-Logic 2300 series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Q-Logic 2300 series.

Similar manuals

A complete manual for the device Q-Logic 2300 series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Q-Logic 2300 series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Q-Logic 2300 series.

A complete Q-Logic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Q-Logic 2300 series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Q-Logic 2300 series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Q-Logic 2300 series, that we can find in the current document
3. Tips how to use the basic functions of the device Q-Logic 2300 series - which should help us in our first steps of using Q-Logic 2300 series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Q-Logic 2300 series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Q-Logic 2300 series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Q-Logic 2300 series?

Use the form below

If you did not solve your problem by using a manual Q-Logic 2300 series, ask a question using the form below. If a user had a similar problem with Q-Logic 2300 series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)