English dropdown-ico

Manual Alpine SPX-137A

20 pages 0.99 mb
Download

Go to site of 20

Summary
  • Alpine SPX-137A - page 1

    SPX-177A / SPX-137A Component 2-way Speaker System OWNER’S MANUAL Please read before using this equipment MANUEL DE L'UTILISA TEUR V euillez lire le présent manuel avant la mise en service du matériel. ALPINE ELECTRONICS, INC. T okyo office ; 1-1-8 Nishi Gotanda, Shinagawa-ku, T okyo 141-8501, Japan T el.: (03) 3494-1 101 ALPINE ELECTRONIC ...

  • Alpine SPX-137A - page 2

    2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LES INST ALLER CORRECTEMENT . L’utilisation d’autres pièces non désignées risque de provoquer des dommages à l’intérieur de l’appareil ou son installa- tion risque de ne pas être faite correctement, et les pièces desserrées peuvent provoquer des dangers. NE P AS INST ALLER DANS DES E ...

  • Alpine SPX-137A - page 3

    3 19. Fixed-flush mount cup / Embase fixe à niveau …………………… x2 20. Mounting clip / Attache de montage .....…………………………. x4 21. Swivel-spacer / Swivel-spacer .....………… ………………. x4 22. Screw st4.2x9.5mm / Vis st4.2x9.5mm....…………………….. x2 23. Screw st4.2x19mm / Vis st4.2x19mm…... ...

  • Alpine SPX-137A - page 4

    4 T abel of Contents Installation W oofer (SPX-177A)..................................................................... 5 W oofer (SPX-137A)..................................................................... 7 T weeter ........................................................................................ 8 Crossover Network................... ...

  • Alpine SPX-137A - page 5

    5 Installation (SPX-177A) W oofer: Surface mount W oofer: Factory/stealth Notes: l Attach gasket tape as shown. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm Notes: l Attach gasket tape as shown. st4.2x25mm Installation (SPX-177A) W oofer : Montage en surface W oofer : Usine / montage ...

  • Alpine SPX-137A - page 6

    6 Installation (SPX-177A) W oofer: Factory/OEM custom fit Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs. Hardware: l Use st4.2x25mm for adapter to vehicle l Use M4x10mm for speaker to adapter (adapter only) l Use M4x18mm for speaker to adapter (adapter + spacer) l Use M4x20mm fo ...

  • Alpine SPX-137A - page 7

    7 Installation (SPX-137A) W oofer: Surface mount Notes: l Attach gasket tape as shown, then lock speaker into grille ring. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm W oofer: Factory/stealth Notes: l Attach gasket tape as shown. st4.2x25mm W oofer: Factory/Size-up/OEM custom fit Not ...

  • Alpine SPX-137A - page 8

    8 Installation T weeter: Swivel-surface mount st4.2x19mm Fig. 1 Fig. 2 Fig. 3 Notes: l Before mounting, insert swivel retention cup into housing. Then rotate until achieving a positive lock using an appropriate tool (screwdriver , etc.). l Mount complete swivel-surface cup and fix swivel spacer to base. (Fig. 1) l Lock swivel ring to tweeter housin ...

  • Alpine SPX-137A - page 9

    9 Installation T weeter: Swivel-flush mount Fig. 1 Fig. 2 Fig. 3 Notes: l Before mounting, insert swivel retention cup into housing. Then rotate until achieving a positive lock using an appropriate tool (screwdriver , etc.). l Insert complete swivel-flush cup with mounting clips first through opening. (Fig. 1) l Press mounting clips at center and s ...

  • Alpine SPX-137A - page 10

    10 Installation T weeter: Fixed-flush mount Fig. 1 Fig. 2 Fig. 3 Notes: l Insert fixed-flush cup with mounting clips first through opening. (Fig. 1) l Press mounting clips at center and secure with screw . (Fig. 2) l Make connections, then insert and lock tweeter into cup. (fig. 3) st4.2x9.5mm Caution: l If custom painting is desired, remove grille ...

  • Alpine SPX-137A - page 11

    11 Installation T weeter: Surface-angle mount Notes: l Remove network cover , and mount as shown l Connect wires to terminal blocks accordingly . (see System Connection Diagrams section) l Make appropriate jumper settings using jumper puller tool (see Crossover Network Settings section) l Re-secure network cover . Crossover Network st4.2x19mm Notes ...

  • Alpine SPX-137A - page 12

    12 System Connections Single Input Bi-wire Input Note: Signal link jumpers highlighted in black must be inserted for proper function of single input configuration. Wiring for connection of crossover network to amplifier is not included. Caution: These jumpers must be removed when using b-wire input. Connexions du système Entrée simple Entrée par ...

  • Alpine SPX-137A - page 13

    13 Crossover Network Settings It is common knowledge that the automotive environment poses numerous acoustic challenges to achieving high-fidelity sound. Fortunately , many of these problems can be overcome with proper speaker placement, equalization, digital time correction, or other techniques. However, the transition between drivers in a speaker ...

  • Alpine SPX-137A - page 14

    14 Crossover Network Settings System T ype 1 (default) Speaker Placement Description: In this system type, woofer and tweeter are mounted in close proximity to each other , and are mounted in essentially the same plane. Due to positioning limitations in some applications, additional tuning may be required using the axis jumpers for both the woofer ...

  • Alpine SPX-137A - page 15

    15 Crossover Network Settings System T ype 1 Filter Description: In this setting, the woof er and tweeter are at appro ximately equal distance from the listener . Using the kic k-panel for placement is only one of man y locations av ailable to mount both drivers together . What is impor tant is that but b y put- ting these tw o dr i vers in close p ...

  • Alpine SPX-137A - page 16

    16 Crossover Network Settings System T ype 2 Speaker Placement Description: In this system type, woofer and tweeter are mounted different locations and at dif ferent distances from the listener . Also of significance, is the fact that the tweeter is the nearest driver . All component locations listed below are commonly available in most vehicles, b ...

  • Alpine SPX-137A - page 17

    17 Crossover Network Settings System T ype 2 Filter Description: In this system type, the woofer is in a dif ferent plane from the tweeter , making it necessary to use the phase correction sections of the network to compensate for the different relative positions. With this particular network set- ting, user adjustment of the woofer axis jumpers is ...

  • Alpine SPX-137A - page 18

    18 ...

  • Alpine SPX-137A - page 19

    19 Specifications Specifications System SPX-177A SPX-137A T ype Component 2-wa y speak er Component 2-w ay speak er P ower Handling (peak/RMS) 240/60 W 200/50 W Impedance 4 W 4 W F requency Response 35-35 kHz 35-35 kHz Net W eight 5 kg 4.5 kg Drivers General Speaker siz e 6.5” (SPX-177A) 5.25” (SPX-137A) 26 mm Speaker T ype Bass/Midrange Bass/M ...

  • Alpine SPX-137A - page 20

    Designed by Alpine Electronics of America, Inc. Printed in Denmark by T eam L ynderup ...

Manufacturer Alpine Category Speaker

Documents that we receive from a manufacturer of a Alpine SPX-137A can be divided into several groups. They are, among others:
- Alpine technical drawings
- SPX-137A manuals
- Alpine product data sheets
- information booklets
- or energy labels Alpine SPX-137A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Alpine SPX-137A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Alpine SPX-137A, service manual, brief instructions and user manuals Alpine SPX-137A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Alpine SPX-137A.

Similar manuals

A complete manual for the device Alpine SPX-137A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Alpine SPX-137A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Alpine SPX-137A.

A complete Alpine manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Alpine SPX-137A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Alpine SPX-137A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Alpine SPX-137A, that we can find in the current document
3. Tips how to use the basic functions of the device Alpine SPX-137A - which should help us in our first steps of using Alpine SPX-137A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Alpine SPX-137A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Alpine SPX-137A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Alpine SPX-137A?

Use the form below

If you did not solve your problem by using a manual Alpine SPX-137A, ask a question using the form below. If a user had a similar problem with Alpine SPX-137A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)