English dropdown-ico

Manual Pelco CM9760-PEX

16 pages 14.4 mb
Download

Go to site of 16

Summary
  • Pelco CM9760-PEX - page 1

    CM9760-PEX Por t Expander Installation/ Operation Manual C546M (8/98) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 ® ...

  • Pelco CM9760-PEX - page 2

    2 Pelco Manual C546M (8/98) REVISION HISTOR Y Manual # Date Comments C546M 8/98 Original version. CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS ............................... 3 2.0 DESCRIPTION ............................ ...

  • Pelco CM9760-PEX - page 3

    Pelco Manual C546M (8/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified serv ...

  • Pelco CM9760-PEX - page 4

    4 Pelco Manual C546M (8/98) Figure 1. Fully Populated CM9760-PEX (Port Expander) Rear View . 2.0 DESCRIPTION The Pelco CM9760-PEX (Port Expander) is designed to increase the number of devices that can be connected to a CM9760-CC1, using additional serial communication channels to increase port density . Currently the CM9760-PEX supports: 1. Pelco C ...

  • Pelco CM9760-PEX - page 5

    Pelco Manual C546M (8/98) 5 2.1 MODELS CM9760-PEX A port expander card cage capable of containing up to five port expansion cards. Each installed card assembly expands one COMM port on the rear of the CM9760-CC1 from one to eight ports. 2.2 OPTIONS CM9760-PEX-CRD The basic building block of the CM9760-PEX, consisting of a port expansion card, its e ...

  • Pelco CM9760-PEX - page 6

    6 Pelco Manual C546M (8/98) 3.0 INST ALLA TION 3.1 HARDW ARE 3.1.1 Card Expansion Installation Each port expander card has its own microprocessor and power regulator . No communication exists between port expander cards. Cards are installed from the front of the unit after the quick-disconnect screws which hold the front panel in place are loosened ...

  • Pelco CM9760-PEX - page 7

    Pelco Manual C546M (8/98) 7 3.1.2 DIP Switch Settings Each port expansion card, before being installed into the CM9760-PEX card cage should be properly configured with respect to DIP switch settings. The switch setting positions configure communication attributes as well as condition the PEX for the device type connected to each expansion card. The ...

  • Pelco CM9760-PEX - page 8

    8 Pelco Manual C546M (8/98) Figure 4. Pin Connections Between a CM9760-PEX and CM9760-CC1 Figure 5. Pin Connections Between a CM9760-PEX and Pelco Receiver/Drivers 3.1.3.1 Connection Between a CM9760-PEX and a CM9760-CC1 The connection of a CM9760-PEX and a CM9760-CC1 is illustrated in Figure 4. Every Port Expander card input port requires a separa ...

  • Pelco CM9760-PEX - page 9

    Pelco Manual C546M (8/98) 9 Figure 6. Pin Connections Between a CM9760-PEX and a Multiplexer Figure 7. Pin Connections Between a CM9760-PEX and CM9760-KBD 3.1.3.3 Connection Between a CM9760-PEX and Multiplexers The connection of a Multiplexer to a CM9760-PEX is illustrated in Figure 6. On e Multiplexer can be connected to each comms port on a Port ...

  • Pelco CM9760-PEX - page 10

    10 Pelco Manual C546M (8/98) 3.1.4 System Illustration Figure 8 illustrates a port expander included in a hypothetical CM9760 system setup. Figure 8. Example of Port Expander as Part of CM9760 System ...

  • Pelco CM9760-PEX - page 11

    Pelco Manual C546M (8/98) 11 3.2 SOFTW ARE 3.2.1 Address Details Normally , up to 16 camera receiver/drivers can be connected to one SerCom 8 port on a CM9760-CC1; however , up to 128 camera receiver/drivers can be connected to the same port through expansion by using a Port Expander . Camera receiver/ drivers are numbered from 1 to 16. T o uniquel ...

  • Pelco CM9760-PEX - page 12

    12 Pelco Manual C546M (8/98) 3.2.2 Software Considerations We now expand the previous section (using receiver/drivers as the attached device) to include the configuration of the necessary software files that need to be setup before successful operation of the PEX can be realized. T wo Setup files in the SET9760 program need to be adjusted if a CM97 ...

  • Pelco CM9760-PEX - page 13

    Pelco Manual C546M (8/98) 13 Figure 10. Camera File Configuration Figure 10 illustrates the other file we previously mentioned-the camera (.CAM) file. It is here that address parameters for each attached receiver/driver is uniquely identified. Also note that this file is used to configure multiplexers, if needed. Refer to the “type” pull-down m ...

  • Pelco CM9760-PEX - page 14

    14 Pelco Manual C546M (8/98) 4.0 GUIDELINES FOR POR T EXP ANDER USE The following points are listed as Pelco recommended guidelines for port expander use. The reason the port expander exists at all is to extend the current port limit past that physically allowed by the CM9760-CC1. Even though, the 32 port limit imposed by the CC1 is usually suffici ...

  • Pelco CM9760-PEX - page 15

    Pelco Manual C546M (8/98) 15 5.0 SPECIFICA TIONS ELECTRICAL Input Voltage: 120 VAC or 230 VAC 50/60 Hz. ± 10%, selectable Power Consumption: 100 VA Fusing: 2 Amps COMMUNICATIONS Data Ports Input: DB-9,RS-422 male connectors DIP switch selectable baud rate Output: DB-9, RX-422 female connectors DIP switch selectable baud rate MECHANICAL Connectors ...

  • Pelco CM9760-PEX - page 16

    16 Pelco Manual C546M (8/98) 6.0 W ARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective ...

Manufacturer Pelco Category Film Camera

Documents that we receive from a manufacturer of a Pelco CM9760-PEX can be divided into several groups. They are, among others:
- Pelco technical drawings
- CM9760-PEX manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco CM9760-PEX
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco CM9760-PEX.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco CM9760-PEX, service manual, brief instructions and user manuals Pelco CM9760-PEX. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco CM9760-PEX.

Similar manuals

A complete manual for the device Pelco CM9760-PEX, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco CM9760-PEX by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco CM9760-PEX.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco CM9760-PEX - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco CM9760-PEX, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco CM9760-PEX, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco CM9760-PEX - which should help us in our first steps of using Pelco CM9760-PEX
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco CM9760-PEX
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco CM9760-PEX in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco CM9760-PEX?

Use the form below

If you did not solve your problem by using a manual Pelco CM9760-PEX, ask a question using the form below. If a user had a similar problem with Pelco CM9760-PEX it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)