English dropdown-ico

Manual Pelco FR8308

24 pages 0.3 mb
Download

Go to site of 24

Summary
  • Pelco FR8308 - page 1

    INST ALLA TION FT8308/FR8308 Fiber T ransmitter and Receiver Eight-Channel Digitally Encoded V ideo C1647M-A (6/06) ...

  • Pelco FR8308 - page 2

    ...

  • Pelco FR8308 - page 3

    C1647M-A (6/06) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Overview . . . . . . . . . . . . . . . . . ...

  • Pelco FR8308 - page 4

    4 C1647M-A (6/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install nea ...

  • Pelco FR8308 - page 5

    C1647M-A (6/06) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO ...

  • Pelco FR8308 - page 6

    6 C1647M-A (6/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Thi ...

  • Pelco FR8308 - page 7

    C1647M-A (6/06) 7 Product Overview DESCRIPTION The FT8308/FR8308 fi ber transmitter and receiver provide the ability to transmit up to eight composite video channels over one optical fi ber (refer to Figure 1). Figure 1. Eight-Channel Video FT8308 T ransmitter and FR8308 Receiver Features of the FT8308/FR8308 fi ber optic transmission system inc ...

  • Pelco FR8308 - page 8

    8 C1647M-A (6/06) MODELS The FT8308/FR8308 fi ber transmitter and receiver consist of the following series of models: Multimode Models:* FT8308MSTR Eight-channel fiber optic video transmitter; multimode, ST connector FR8308MSTR Eight-channel fiber optic video receiver; multimode, ST connector Single-Mode Models: * FT8308SSTR Eight-channel fiber ...

  • Pelco FR8308 - page 9

    C1647M-A (6/06) 9 FRONT PANEL The front panel of the FT8308 transmitter and the FR8308 receiver provides LED indicators that allow you to monitor signal status , laser status (transmitter only), and operating power. The following sections provide a view of the front panel of the FT8308 transmitter and the FR8308 receiver . FRONT PANEL - FT8308 T RA ...

  • Pelco FR8308 - page 10

    10 C1647M-A (6/06) FRONT PANEL - FR8308 RECEIVER Figure 3 illustrates the front panel of the FR8308 receiver. Figure 3. Front Panel of FR8308 Receiver For detailed information about the front-panel indicators, refer to the T roubleshooting section.  VIDEO PRESENT LEDs 1-8  OPTIC FAUL T LED, optical signal s tatus indicator  POWER LED (Pelc ...

  • Pelco FR8308 - page 11

    C1647M-A (6/06) 11 REAR PANEL Connections to the FT8308 transmitter and the FR8308 receiver are made to the rear panel of the modules. The following sections provide a view of the rear panel of the FT8308 transmitter and the FR8308 receiver . REAR PANEL - FT8308 T RANSMITTER Figure 4 illustrates the rear panel of the FT8308 transmitter. Figure 4. R ...

  • Pelco FR8308 - page 12

    12 C1647M-A (6/06) REAR PANEL - FR8308 RECEIVER Figure 5 illustrates the rear panel of the FR8308 receiver. Figure 5. Rear Panel of FR8308 Receive r For additional information about rear-panel connections, refer to the Installation section.  RACK POWER/ALARM CONNECTOR, 4-pin connector for power/alarm connection of rack- mounted module  ST AND ...

  • Pelco FR8308 - page 13

    C1647M-A (6/06) 13 Installation PACKAGE CONTENTS The following items are supplied: 1 FT8308 transmitter or FR8308 receiver 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1W all clip with two 4-40 x 0.250-inch Phillips pan head sc ...

  • Pelco FR8308 - page 14

    14 C1647M-A (6/06) MOUNTING THE T RANSMITTER/RECEIVER TO A W ALL The FT8308 transmitter/FR8308 receiver can be mounted to a wall in the following ways: • Using the supplied wall clip for attachment of a single module to a wall. For installation instructions, refer to the Mounting the T ransmitter/Receiver Using the Wall Clip section below . • U ...

  • Pelco FR8308 - page 15

    C1647M-A (6/06) 15 Figure 6. Mounting the FT8308 T ransmitter/FR8308 Receiver Using the W all Clip TRANSMITTER/ RECEIVER W ALL CLIP LOWER FLANGE SCREW , PHILLIPS PA N HEAD WITH LOCK W ASHER (2) HORIZONT AL MOUNTING HOLE (2) UPPER FLANGE VERTICAL MOUNTING HOLE (2) ...

  • Pelco FR8308 - page 16

    16 C1647M-A (6/06) CONNECTIONS Connections to the FT8308 transmitter and the FR8308 receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a stand-alone module. A 12 VDC power supply is provided. If a ...

  • Pelco FR8308 - page 17

    C1647M-A (6/06) 17 T roubleshooting LED indicators on the front panel of the FT8308 transmitter/FR8308 receiver (refer to Figure 2 and to Figure 3, respectively) allow you to monitor signal status, laser status (transmitter only), and operating power . T able A provides information about the front-panel indicators and associated troubleshooting gui ...

  • Pelco FR8308 - page 18

    18 C1647M-A (6/06) Video Present LED (Continued) Red on receiver Incoming video signal is not present on the channel. Optical signal is not being received from the trans- mitter . Optic Fault LED is also red. Refer to the Optic Fault LED - Receiver section in this table. Video source is not powered on. Check power connection to the video source. Vi ...

  • Pelco FR8308 - page 19

    C1647M-A (6/06) 19 Optic Fault LED - Receiver Green The optical signal is being received from the transmitter . — No action required. Red The optical signal is not being received from the transmitter . T ransmitter is not powered on. Check power connections. Replace power supply if necessary . Fiber optic cable is not connected. Check fiber opti ...

  • Pelco FR8308 - page 20

    20 C1647M-A (6/06) Specifications VIDEO Number of Channels 8 Modulation T ype Pulse code modulation, 8-bit resolution Video Input (FT8308)/ 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM Video Output (FR8308) Bandwidth 6.5 MHz Gain Unity Crosstalk -50 dB typical at 3.58 MHz Differential Gain <1% Differential Phase <1.2° T ilt <1% Signal-to-Nois ...

  • Pelco FR8308 - page 21

    C1647M-A (6/06) 21 OPTICAL POWER BUDGET , TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT Model No. Wavelength Optical Power Budget Maximum T ransmission Distance Laser Class 1 Limit* T ransmitter Compatible Receiver Multimode (62.5/125 µm) FT8308MSTR FR8308MSTR 1310 nm 20 dB † 1 km (0.6 mi) ‡ <15.6 mW Single-Mode (9/125 µm) FT8308SSTR FR83 ...

  • Pelco FR8308 - page 22

    22 C1647M-A (6/06) The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and el ...

  • Pelco FR8308 - page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted p ...

  • Pelco FR8308 - page 24

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Manufacturer Pelco Category Stereo Receiver

Documents that we receive from a manufacturer of a Pelco FR8308 can be divided into several groups. They are, among others:
- Pelco technical drawings
- FR8308 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco FR8308
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco FR8308.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco FR8308, service manual, brief instructions and user manuals Pelco FR8308. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco FR8308.

Similar manuals

A complete manual for the device Pelco FR8308, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco FR8308 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco FR8308.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco FR8308 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco FR8308, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco FR8308, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco FR8308 - which should help us in our first steps of using Pelco FR8308
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco FR8308
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco FR8308 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco FR8308?

Use the form below

If you did not solve your problem by using a manual Pelco FR8308, ask a question using the form below. If a user had a similar problem with Pelco FR8308 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)