English dropdown-ico

Manual Hunter Fan 81001

28 pages 5.06 mb
Download

Go to site of 28

Summary
  • Hunter Fan 81001 - page 1

    Installation Guide 81001 & 81003 Ashbur y Bath Ventilator with Light READ and SAVE THESE INSTR UCTIONS 41937-01 3/29/2006 ENGLISH See page 2 ESp añoL Vea la página 15 05-HF-025_EngS_3.29.06.indd 1 3/29/06 7:33:52 PM ...

  • Hunter Fan 81001 - page 2

    2 DISCoNNECT ELECTRIC poWER SUppL Y aND LoCK oUT SERVICE p aNEL BEFoRE SERVICING UNIT W arning TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY , OBSERVE THE FOLLOWING: 1. For general ventilating use only . Do not use for ventilat- ing hazardous or explosive materials. 2. T o avoid motor bearing damage and noisy/unbalanced impellers, keep dr ywall sp ...

  • Hunter Fan 81001 - page 3

    x2 E F G H I J K L 95047-03-000 75864-01-000 03242-07-133 95261-02-000 74508-03-133 96397-01-214 for model 81001 96397-02-444 for model 81003 75184-01-133 86812-01-000 for model 81001 86812-03-000 for model 81003 M 75733-01-214 for model 81001 75733-01-444 for model 81003 x4 * * * NO TE: Strain relief cable connector must be installed. Not Inc lude ...

  • Hunter Fan 81001 - page 4

    5 4 7 G 8 F Remove the motor/blower from the housing. 4 H E 3 Remove the pre-loaded screw tip co vers. Remove the wiring cover screw . 6 Back out the pre-loaded screw tips until flush with the side of the housing. Remove the wiring cover . Remove packing material. 41937-01 3/29/2006 41937-01 3/29/2006 05-HF-025_EngS_3.29.06.indd 4 3/29/06 7:33:57 P ...

  • Hunter Fan 81001 - page 5

    9 E Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and secure with washer . Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. New Construction 5 1 0 B C Choose Installation Option F or New Construction - go to step A11, page ...

  • Hunter Fan 81001 - page 6

    A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground A 1 4 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option Connect wires as shown. A 1 3 Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). 0 0 A 1 6 Con ...

  • Hunter Fan 81001 - page 7

    A 1 9 I A2 0 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Secure the motor by tightening the 2 screws. T urn on the power source. 7 Connect wiring harness. DO NOT ALLOW THE MO TOR TO HANG FROM THE WIRING HARNESS. 0 0 0 0 0 0 0 0 A 1 7 0 0 0 0 0 0 0 0 H ...

  • Hunter Fan 81001 - page 8

    EXISTING F AN B 1 1 E B 1 2 8 Existing Construction B 1 3 2 1 B 1 4 Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). Remove an existing fan and check to make sure the open- ing is large enough to accommodate the new motor hous- ing (7 1/4”x 7 3/4”). Move the housing into position ab ...

  • Hunter Fan 81001 - page 9

    9 H B 1 8 H B 1 9 B 2 0 I Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MO TOR TO HANG FROM THE WIRING HARNESS. Secure the motor by tightening the 2 screws. A 3 Pin 2 Pin Fan Motor Light Light Green Black Black W ...

  • Hunter Fan 81001 - page 10

    10 O N O F F B 2 2 B 2 3 C1 Go to step on page 10 to attach grille . B 2 1 T est the motor . If the motor does not run, check the plug connection. T urn on the power source. J M C 2 L K C 1 Attaching the Grille Remove the thumbscrews. Remove glass dome. 41937-01 3/29/2006 41937-01 3/29/2006 05-HF-025_EngS_3.29.06.indd 10 3/29/06 7:34:12 PM ...

  • Hunter Fan 81001 - page 11

    11 C 4 J J K C 5 C 6 C 7 L M C 8 Align posts 1, 2, and 3 (stamped into motor housing) with posts 1, 2, and 3 (stamped into light fixture). Slide light fixture over posts. Attach thumbscrews. WARNING: T o reduce the risk of electrical shock, all 3 thumbscrews MUST be properly installed. Align glass dome and push up. Install 2 Max 60 Watt A15 bulbs ( ...

  • Hunter Fan 81001 - page 12

    12 T rouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. T o confirm that the fan is running, place your hand near the vents to feel the air movement. • T urn po wer on, replace fuse, or reset breaker . • Check all plug connections to be sure they are secure. • Check the wiring to mak ...

  • Hunter Fan 81001 - page 13

    13 W arranty Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warr anty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to y ...

  • Hunter Fan 81001 - page 14

    2500 Frisco Avenue, Memphis, T ennessee 38114 Printed in China 41937-01 3/29/2006 14 © 2006 Hunter Fan Company 05-HF-025_EngS_3.29.06.indd 14 3/29/06 7:34:17 PM ...

  • Hunter Fan 81001 - page 15

    DESDE Guía de instalación V entilador para baño Ashbur y 81001 y 81003 con luz LEA y CONSERVE EST AS INSTR UCCIONES 41937-02 3/29/2006 15 Esp añol 05-HF-025_Sp_3.29.06.indd 15 3/29/06 7:34:57 PM ...

  • Hunter Fan 81001 - page 16

    16 DEsCoNECTE la alIMENT aCIÓN ElÉCTRICa Y CIERRE El p aNEl DE sERVICIo aNTEs DE DaR MaNTENIMIENTo a la UNIDaD tc. Retire las cubiertas de las puntas de tornillo precargadas. ADVER TENCIA P A R A R E D U C I R E L R IE S G O D E D ES C A R G A E L É C T R I C A O L E S I O N E S , OB SE RV E L O S IG U I E N T E: 1. Sólo para uso de ventilació ...

  • Hunter Fan 81001 - page 17

    x2 E F G H I J K L 95047-03-000 75864-01-000 03242-07-133 95261-02-000 74508-03-133 75184-01-133 86812-01-000 para modelo 81001 86812-03-000 para modelo 81003 M x4 * * A B C x2 D 96397-01-214 para modelo 81001 96397-02-444 para modelo 81003 75733-01-214 para modelo 81001 75733-01-444 para modelo 81003 Conector de cable de 3/8” * Nota: Debe estar ...

  • Hunter Fan 81001 - page 18

    5 4 7 G 8 F 18 H E 3 6 Retire el motor/soplador del alojamiento. Retire las cubiertas de las puntas de tornillo precargadas. Retire el tornillo de la cubierta del cableado. Retire las puntas de tornillo precargadas hasta que estén a nivel con el lado del alojamiento. Retire la cubierta del cableado. Retire el material de embalaje. 41937-02 3/29/20 ...

  • Hunter Fan 81001 - page 19

    9 E 19 1 0 B C A 1 1 E 5/8 1/2 5/8 1/2 A 1 2 Inserte el manguito de alivio de tensión (no se inc luye) en la caja y sujételo firmemente con una arandela. Ubique la correcta marca de profundidad en el borde inferior de la viga, según el espesor de su plancha de yeso. Construcción nueva Escoja la opción de instalación P ara construcción nueva ...

  • Hunter Fan 81001 - page 20

    A Motor del ventilador Luz Verde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Blanco Negro Luz Blanco Blanco Cobre desnudo Tierra A 1 4 *Opción Ventilador y luz principal juntos *Opción Negro 3 pasadores 3 clavijas 2 pasadores 2 clavijas A 1 3 0 0 A 1 6 20 A 1 5 E F G Tienda los cables a través del manguito de alivio de tension. P ...

  • Hunter Fan 81001 - page 21

    A 1 9 I A2 0 21 0 0 0 0 0 0 0 0 A 1 7 0 0 0 0 0 0 0 0 H A 1 8 E N C E N D I D O A P A GA DO A 2 1 A2 2 C1 Vaya al paso en la página 24 para fijar la rejilla. Asegure el motor apretando los 2 tornillos. Encienda la fuente de alimentación. Conecte el mazo de cables. NO PERMIT A QUE EL MOTOR CUELGUE DEL MAZO DE CABLES. V uelva a instalar el motor in ...

  • Hunter Fan 81001 - page 22

    VENTILADOR EXISTENTE B 1 1 E B 1 2 22 Construcción existente B 1 3 2 1 B 1 4 E B 1 5 Tienda los cables a través del manguito de alivio de tension. Para conexiones de alimentación, use alambres adecuados al menos para 90º C (194º F). Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamie ...

  • Hunter Fan 81001 - page 23

    23 H B 1 8 H B 1 9 B 2 0 I A Motor del ventilador Luz Verde Negro Interruptor 2 (CA) Negro Interruptor principal 1 (CA) Blanco Negro Luz Blanco Blanco Cobre desnudo Tierra B 1 6 *Opción Ventilador y luz principal juntos *Opción Negro 3 pasadores 3 clavijas 2 pasadores 2 clavijas F B 1 7 G Conecte los alambres como se muestra. V uelva a instalar e ...

  • Hunter Fan 81001 - page 24

    24 O N O F F B 2 2 B 2 3 C1 Vaya al paso en la página 24 para fijar la rejilla. B 2 1 J M C 2 L K C 1 Fijación de la rejilla Pruebe el motor . Si el motor no funciona, verifique la conexión del enchufe. Encienda la fuente de alimentación. Retire los tornillos de mano. Retire la pantalla. 41937-02 3/29/2006 41937-02 3/29/2006 05-HF-025_Sp_3.29.0 ...

  • Hunter Fan 81001 - page 25

    25 C 4 J J K C 5 C 6 C 7 L M C 8 Alinee los postes 1, 2 y 3 (estampados en la caja del motor) con los postes 1, 2 y 3 (estampados en el artefacto de iluminación). Deslice la lámpara sobre los postes. Instale los tornillos de mano. ADVERTENCIA: P ara reducir el riesgo de descarga eléctrica, los 3 tornillos de mano DEBEN instalarse apropiadamente. ...

  • Hunter Fan 81001 - page 26

    26 Solución de problemas Problema: El ventilador no está operando. Solución: • Los ventiladores de baño Hunter son muy silenciosos. Para confirmar que el ventilador esté funcionando, coloque su mano cerca de los conductos de ventilación para sentir el movimiento del aire. • Encienda la alimentación eléctrica, reemplace el fusible o res ...

  • Hunter Fan 81001 - page 27

    27 41937-02 3/29/2006 41937-02 3/29/2006 Garantía Hunter Fan Company Extractor de aire para baño GARANTÍA LIMIT ADA Hun ter Fan Co mpan y e stab lec e l a si gui ent e ga ran tía li mita da al u sua rio o c omp rad or orig ina l de es te Extr act or de air e pa ra bañ o H unte r: Si alguna pieza de su Extractor de aire para baño Hunter (con e ...

  • Hunter Fan 81001 - page 28

    2500 Frisco Avenue, Memphis, T ennessee 38114 Impreso en China 41937-02 3/29/2006 © 2006 Hunter Fan Company 05-HF-025_Sp_3.29.06.indd 28 3/29/06 7:35:22 PM ...

Manufacturer Hunter Fan Category Universal Remote

Documents that we receive from a manufacturer of a Hunter Fan 81001 can be divided into several groups. They are, among others:
- Hunter Fan technical drawings
- 81001 manuals
- Hunter Fan product data sheets
- information booklets
- or energy labels Hunter Fan 81001
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hunter Fan 81001.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hunter Fan 81001, service manual, brief instructions and user manuals Hunter Fan 81001. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hunter Fan 81001.

Similar manuals

A complete manual for the device Hunter Fan 81001, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hunter Fan 81001 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hunter Fan 81001.

A complete Hunter Fan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hunter Fan 81001 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hunter Fan 81001, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hunter Fan 81001, that we can find in the current document
3. Tips how to use the basic functions of the device Hunter Fan 81001 - which should help us in our first steps of using Hunter Fan 81001
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hunter Fan 81001
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hunter Fan 81001 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hunter Fan 81001?

Use the form below

If you did not solve your problem by using a manual Hunter Fan 81001, ask a question using the form below. If a user had a similar problem with Hunter Fan 81001 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)