Manual Hobart WS-80

10 pages 1.48 mb
Download

Go to site of 10

Summary
  • Hobart WS-80 - page 1

    WS-40/80 Hobart Compact Water Softener Installation Instructions WS-40 WS-80 - NOTICE - This Manual is prepared for the use of trained Hobart Service Technicians and should not be used by those not properly qualified. This manual is not intended to be all encompassing. If you have not attended a Hobart Service School for this product, you should re ...

  • Hobart WS-80 - page 2

    TABLE OF CONTENTS INSTALLATION ............................................................................................ 3 INSTALLATION WS-40/80 .............................................................................. 3 DISC REPLACEMENT ...................................................................................... 8 DISC REPLACEMEN ...

  • Hobart WS-80 - page 3

    INSTALLATION INSTALLATION WS-40/80 SAVE THESE INSTRUCTIONS Disconnect the electrical power to the machine and follow lockout / tagout procedures. 1. Locate water supply line and appropriate drains for softener installation. 2. Install by-pass valving. Fig. 1 3. Install high temperature prefilter if needed. Fig. 2 4. Remove all items from shipping p ...

  • Hobart WS-80 - page 4

    Fig. 5 9. Install one O-Ring into each groove of the brass adapter. Fig. 6 10. Apply a small amount of seal lube evenly onto each O-ring. Fig. 7 11. Remove the pin and bracket from the softener in/ out port area. Fig. 8 12. Install the brass adapters into the in/out ports and secure by reinstalling the bracket and pin. Fig. 9 13. The female end of ...

  • Hobart WS-80 - page 5

    15. Insert tubing provided into the overflow port on the back of the softener and run drain lower than the cabinet connection to provide a gravity drain in the event of a internal cabinet leak. Fig. 10 16. Review the meter disc selection chart and the water analysis provided. If no water analysis is provided test the water supply. 17. To test the w ...

  • Hobart WS-80 - page 6

    Brine Valve Settings Unit Brine Setting Float Cup Height WS-40 1.0 lb. 6.25" WS-80 1.4 lb. 6.5" E. Reinstall brine valve into the cabinet. NOTE: Do not drop brine valve into drum. Dropping may lower float cup, resulting in an improper setting. 20. To install salt alarm system remove paper lining from back of salt alarm connector box. Fig. ...

  • Hobart WS-80 - page 7

    Fig. 17 27. Check for proper operation by pressing the recessed red button on bottom of salt alarm controller. If controller is operating properly - the indicator light will flash and an audible tone will be heard. Fig. 18 28. 29. Add a clean grade of salt at this time. Higher grades of Pelletized Salt for impurities and solubility should be used. ...

  • Hobart WS-80 - page 8

    DISC REPLACEMENT DISC REPLACEMENT WS-40/80 1. Remove screws and cap cover from level one. Fig. 19 2. Remove balance piston. Fig. 20 3. Remove balance piston o-ring and balance piston spring. Fig. 21 4. Remove meter drive pawl. Fig. 22 5. Remove meter disc. Fig. 23 WS-40/80 Hobart Compact Water Softener Installation Instructions - DISC REPLACEMENT F ...

  • Hobart WS-80 - page 9

    6. Install correct meter disc and reassemble in reverse order. NOTE: Be certain to start cap screws by hand rotating backwards until screw drops into thread then tighten. An alternating, crossing pattern should be used while tightening cap screws to ensure correct cap fit. WS-40/80 Hobart Compact Water Softener Installation Instructions - DISC REPL ...

  • Hobart WS-80 - page 10

    DISC SELECTION DISC SELECTION WS-40/80 The amount of hardness removed (in compensated gpg) will be based on the amount of brine and the meter disc selected. 1. Determine the compensated hardness. This requires a hardness test and an iron test on raw water at the application site. Compensated hardness is calculated by multiplying the ferrous iron (i ...

Manufacturer Hobart Category Water System

Documents that we receive from a manufacturer of a Hobart WS-80 can be divided into several groups. They are, among others:
- Hobart technical drawings
- WS-80 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart WS-80
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart WS-80.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart WS-80, service manual, brief instructions and user manuals Hobart WS-80. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart WS-80.

Similar manuals

A complete manual for the device Hobart WS-80, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart WS-80 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart WS-80.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart WS-80 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart WS-80, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart WS-80, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart WS-80 - which should help us in our first steps of using Hobart WS-80
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart WS-80
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart WS-80 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart WS-80?

Use the form below

If you did not solve your problem by using a manual Hobart WS-80, ask a question using the form below. If a user had a similar problem with Hobart WS-80 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)