English dropdown-ico

Manual Jensen JKRS3

16 pages 0.38 mb
Download

Go to site of 16

Summary
  • Jensen JKRS3 - page 1

    128-7052 1 of 16 Kit Contents (1) Control Module (1) 3 Button High Frequency Transmitters (1) 5 Button Two Way LED Based Transceiver (1) On Glass Mount Superheterodyne Transceiver (1) Multi Pin Input/Output Harness (1) Six Pin Power Harness (1) Diesel Wait To Start Input (1) Auxiliary 4 Pin Output Harness (1) 2 Pin Door Lock Harness (2) 30 Amp In-l ...

  • Jensen JKRS3 - page 2

    128-7052 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the ...

  • Jensen JKRS3 - page 3

    128-7052 3 of 16 3 THE TRANSCEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash- board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some n ...

  • Jensen JKRS3 - page 4

    128-7052 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition ...

  • Jensen JKRS3 - page 5

    128-7052 5 of 16 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self-tapping screw and ring terminal. BLACK w/WHITE TRACER WIRE: Control Swit ...

  • Jensen JKRS3 - page 6

    128-7052 6 of 16 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Vol ...

  • Jensen JKRS3 - page 7

    128-7052 7 of 16 7 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue Wire to terminal #86 of a external relay . Connect terminal #85 of the relay to ...

  • Jensen JKRS3 - page 8

    128-7052 8 of 16 Green/Orange Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start u ...

  • Jensen JKRS3 - page 9

    128-7052 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the vehicle door lock / unlock circui ...

  • Jensen JKRS3 - page 10

    128-7052 10 of 16 10 Resistive Circuits, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and o ...

  • Jensen JKRS3 - page 11

    128-7052 11 of 16 11 c. Immediately turn the ignition key OFF. d. Hold the program switch ON, then start the vehicle using the ignition key . e. When the unit senses the tach signal, the parking lights will begin to flash. 6. Release the program switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored and the ...

  • Jensen JKRS3 - page 12

    128-7052 12 of 16 3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote Start Unit. W ARNING!! DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE HOOD PIN SAFETY SHUT DOWN FEA TURE. MANUAL SHU ...

  • Jensen JKRS3 - page 13

    128-7052 13 of 16 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mechanic ...

  • Jensen JKRS3 - page 14

    128-7052 14 of 16 14 such as the light on reminder . These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to the consumer . Circuits may be used only if the above circuit is not available. T o connect to the key in sensor as shown in method 1: 1.Locate the control wire that connects t ...

  • Jensen JKRS3 - page 15

    128-7052 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the ...

  • Jensen JKRS3 - page 16

    128-7052 16 of 16 © 2004 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7052 ...

Manufacturer Jensen Category Remote Starter

Documents that we receive from a manufacturer of a Jensen JKRS3 can be divided into several groups. They are, among others:
- Jensen technical drawings
- JKRS3 manuals
- Jensen product data sheets
- information booklets
- or energy labels Jensen JKRS3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jensen JKRS3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jensen JKRS3, service manual, brief instructions and user manuals Jensen JKRS3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jensen JKRS3.

Similar manuals

A complete manual for the device Jensen JKRS3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jensen JKRS3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jensen JKRS3.

A complete Jensen manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jensen JKRS3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jensen JKRS3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jensen JKRS3, that we can find in the current document
3. Tips how to use the basic functions of the device Jensen JKRS3 - which should help us in our first steps of using Jensen JKRS3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jensen JKRS3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jensen JKRS3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jensen JKRS3?

Use the form below

If you did not solve your problem by using a manual Jensen JKRS3, ask a question using the form below. If a user had a similar problem with Jensen JKRS3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)