English dropdown-ico

Manual Vision Fitness ST200

20 pages 3.48 mb
Download

Go to site of 20

Summary
  • Vision Fitness ST200 - page 1

    Assembly Guide ST200 FUNCTIONAL TRAINER ...

  • Vision Fitness ST200 - page 2

    2 T o avoid possible damage to this Functional T rainer , please follow these assembly steps in the correct order . Before proceeding, find your new Functional T rainer serial number located on the back of the rear floor suppor t (1a), and enter here: Refer to this number when calling for ser vice, and enter this serial number on your W arranty Car ...

  • Vision Fitness ST200 - page 3

    3 2 STEP 1 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 9 STEP ...

  • Vision Fitness ST200 - page 4

    4 19mm Wrench 6mm L-Shaped Wrench TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench ...

  • Vision Fitness ST200 - page 5

    5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 4 10.5 x 18 x 2T Flat W asher Quantity: 8 M10 x 1.5P Nut Quantity: 6 M10 x 1.5P x 60L Bolt Quantity: 4 M10 x 1.5P x 25L Bolt Quantity: 2 M6 x 1P x 15L Bolt Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P Nut Quantity: 2 10.5 x 30 x 2T Flat W asher Quanti ...

  • Vision Fitness ST200 - page 6

    6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P x 25L Bolt Quantity: 8 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 6 10.5 x 18 x 2T Flat W asher Quantity: 4 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P Nut Quantity: 4 10 x 30 x 2T Flat W asher ...

  • Vision Fitness ST200 - page 7

    7 BLACK BAG YELLOW BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 6 M10 x 1.5P Nut Quantity: 4 M10 x 1.5P x 60L Bolt Quantity: 2 M6 x 1P x 50L Bolt Quantity: 2 M12 Slotted Bolt Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 2 M6 x 1P Nut Quantity: 2 Karabiner Quantity: 5 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 2 SW6.1 x 12.2 x ...

  • Vision Fitness ST200 - page 8

    8 RED BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 10 M10 x 1.5P x 25L Bolt Quantity: 10 ...

  • Vision Fitness ST200 - page 9

    9 1d 1b 1e 1c 1a 1 STEP • Lay the back side of the rear vertical upright (1a) down onto the floor . The threaded bolt ends will be pointing up. Place the center floor support (1b) over the threaded ends. Attach a flat (10.5x18x2T) and spring (SW10.2x18.4x2.5T) washer and nut (M10x1.5P) to each end. Tip upright. Tighten fasteners using a 17mm wren ...

  • Vision Fitness ST200 - page 10

    10 2 STEP • Thread pull pins par tially onto 2a (Qty . 1) and 2c (Qty . 2). • Lay the front center vertical (2f) on the floor . Slide the seat suppor t structure (2a) over the open end of 2f. NOTE: Y ou must pull the pull pin out (2b) and hold it when sliding over 2f. Release and engage the pull pin in one of the lower holes of 2f. • Slide th ...

  • Vision Fitness ST200 - page 11

    11 3 STEP • Place the top front structure (3a) on top of 2f and attach with two bolts (M10x1.5Px60L), two flat (10.5x18x2T) washers, and two nuts (M10x1.5P). Tighten fasteners with a 6mm L-shaped wrench and a 17mm wrench. • Attach the seat (3b) up through the bottom of 2a with four bolts (M10x1.5Px25L). Attach the seatback (3c) through 2c with ...

  • Vision Fitness ST200 - page 12

    12 4 STEP • Place the bottom of the left oval upright (4a) onto the protruding bolts of 1d. NOTE: Make sure the 27 holes of 4a are on the outside. Mate the hole in the top of 4a with the top hole of 3a. Attach and tighten one flat (10x30x2T) & spring (SW10.2x18.4x2.5T) wa sh er and one bolt (M10x1.5Px60L). Tighten with a 6mm L-shaped wrench. ...

  • Vision Fitness ST200 - page 13

    13 5 STEP • If you are adding 15 weight plates to the base unit, proceed as follows. If you are adding 20 weight plates, the steel tube spacer (5a) will not be used. • Place two rubber weight plate bumpers (5b) over the 0.75” holes of 5a. Place 5a over the holes of 1b. With the horizontal holes at the bottom, place the two guide rods (5c) ove ...

  • Vision Fitness ST200 - page 14

    14 6 STEP Wrap one end of cable #1 around pulley A. On the right side of the unit, place it through pulleys B, C, D of 6a, and E. Remove the nuts from 2 slotted bolts (M12) (see diagram below). With the threads pointing down on the slotted bolt (M12), slide the end of cable #1 through it. Reattach the nuts on the slotted bolt. Attach it to one side ...

  • Vision Fitness ST200 - page 15

    15 7 STEP If assembling just the base unit ( ST200 ), proceed as follows. If assembling with the leg press ( ST250 ), refer to Step 5 of the leg press assembly guide. Slide the small steel end of cable #2 through pulleys F and G. Remove the nuts from the slotted bolt (M12). Slide the cable through the slotted bolt (M12). Reattach the nuts to the sl ...

  • Vision Fitness ST200 - page 16

    16 8 STEP • Remove the slotted bolts (8a) located on the inside of the right and left handles of uprights 4a & 4b. Remove the nuts from the bolts. Slide the small steel end of cable #3 through pulleys H & I. Continue through pulleys J thru P . Slide the cable through the slotted bolt so that the end pro- trudes out the bottom of the bolt. ...

  • Vision Fitness ST200 - page 17

    17 9 STEP • Place the rear hole of the left decorative cover (9a) over the threaded post on the left side of structure 5e. Loosely attach a spring (SW10.2x18.4x2.5T) washer and a bolt (M10x1.5Px25L). Thread two bolts (M10x1.5Px25L) and two spring (SW10.2x18.4x2.5T) washers into the two front holes. Tighten all bolts with a 6mm L-shaped wrench. Re ...

  • Vision Fitness ST200 - page 18

    18 General Warning/Safet y Decal Placement Weight Plate Sticker Placement 10 STEP • Attach the decals according to the diagram below . DECALS ...

  • Vision Fitness ST200 - page 19

    19 ...

  • Vision Fitness ST200 - page 20

    500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness. All Rights Reserved. 10.05 AG18.37PRD REV2 starts vision with a it all ...

Manufacturer Vision Fitness Category Home Gym

Documents that we receive from a manufacturer of a Vision Fitness ST200 can be divided into several groups. They are, among others:
- Vision Fitness technical drawings
- ST200 manuals
- Vision Fitness product data sheets
- information booklets
- or energy labels Vision Fitness ST200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vision Fitness ST200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vision Fitness ST200, service manual, brief instructions and user manuals Vision Fitness ST200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vision Fitness ST200.

Similar manuals

A complete manual for the device Vision Fitness ST200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vision Fitness ST200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vision Fitness ST200.

A complete Vision Fitness manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vision Fitness ST200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vision Fitness ST200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vision Fitness ST200, that we can find in the current document
3. Tips how to use the basic functions of the device Vision Fitness ST200 - which should help us in our first steps of using Vision Fitness ST200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vision Fitness ST200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vision Fitness ST200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vision Fitness ST200?

Use the form below

If you did not solve your problem by using a manual Vision Fitness ST200, ask a question using the form below. If a user had a similar problem with Vision Fitness ST200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)