English dropdown-ico

Manual Hunter Fan 41787-01

32 pages 5.53 mb
Download

Go to site of 32

Summary
  • Hunter Fan 41787-01 - page 1

    Installation Guide 81004 V entura Bath V entilator F an With Light READ and SAVE THESE INSTR UCTIONS 41787-01 1/11/2006 ...

  • Hunter Fan 41787-01 - page 2

    2 DISCONNECT ELECTRIC POWER SUPPL Y AND LOCK OUT SERVICE P ANEL BEFORE SERVICING UNIT W arning TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY , OBSERVE THE FOLLOWING: 1. For general ventilating use only . Do not use for ventilat- ing hazardous or explosive materials. 2. T o avoid motor bearing dama ge and noisy/unbalanced impellers, keep dr ywall s ...

  • Hunter Fan 41787-01 - page 3

    3 x4 3/8" Cable Connector * * * NO TE: Strain relief cable connector must be installed. Not Inc luded. A B C Extra Screws x2 H E D L 77864-02 F G H I J K 03242-07-133 96261-01-000 95047-02-000 74508-03-133 95776-01-000 75184-01-133 96258-01/02/03-008 75171-01/02/03-000 x2 Included. T urn off the power source. Before Installation Check all the ...

  • Hunter Fan 41787-01 - page 4

    A1 D Back out the pre-loaded screw tips until flush with the side of the housing. Remove the motor/blower from the housing. Remove the wiring cover screw . 4 Remove packing material. A2 A3 A6 F Loosen screw securing motor . A4 A 5 Remove the pre-loaded screw tip co vers. New Construction Installation 41787-01 1/11/2006 ...

  • Hunter Fan 41787-01 - page 5

    A7 E A8 D A9 B C A 1 0 D 5/8 1/2 5/8 1/2 A 1 1 OPTION Remove the wiring cover . Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer . Position the correct depth mark at the bottom edge of the joist–based on the thickness of your sheet rock. Screw pre-loaded screws into j ...

  • Hunter Fan 41787-01 - page 6

    0 A 1 6 D A 1 2 A 1 3 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground A 1 4 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option D E A 1 5 F Pull the wires through the strain relief. Tighten the strain relief screws. Connect wires as shown. Connect a 4” duct a ...

  • Hunter Fan 41787-01 - page 7

    A2 2 C1 Go to step on page 12 to attach grille . 0 0 0 0 D A 1 7 G 0 0 0 0 G D A 1 8 A2 0 O N O F F A 2 1 Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Secure the motor by tightening the 2 screws. ...

  • Hunter Fan 41787-01 - page 8

    B3 7.25 ” 7.75 ” B1 D B2 Loosen screw securing motor . Remove the existing fan and check to make sure the opening is large enough to accommodate the new motor housing (7.25” x 7.75”) . Remove the motor/blower from the housing. Existing F an 8 Remove packing material. D Use the motor housing as a template to mark position. Cut out an opening ...

  • Hunter Fan 41787-01 - page 9

    Pop out the first wiring access slug. Use second if needed. B4 B 5 B8 D B9 B C Back out the pre-loaded screw tips until flush with the side of the housing. 9 B 6 E B7 E Remo ve the wiring cover . Remove the wiring cover screw . Remove the pre-loaded screw tip co vers. Insert the strain relief into the housing and secure with the washer . 41787-01 1 ...

  • Hunter Fan 41787-01 - page 10

    D B 1 0 Fit housing into the opening and secure by tightening the pre-loaded screws into the joist. Note: Install the box flush with the sheetrock (ceiling). B 1 1 2 1 B 1 2 D B 1 3 D B 1 4 10 Pull the wires through the strain relief and tighten the strain relief screws. Attach existing ducting to duct connector . T ape joints. If ducting does not ...

  • Hunter Fan 41787-01 - page 11

    D E F B 1 6 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground B 1 5 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light T ogether *Option D B 1 7 0 0 0 0 G D B 1 8 Install the wiring co ver plate. Make sure all wiring connections are inside the box or under the wiring cover plate. ...

  • Hunter Fan 41787-01 - page 12

    B 2 0 O N O F F B 2 1 B 2 2 C1 Go to step to attach grille . 12 J C 1 T est the motor . If the motor does not run, check the plug connection. T urn on the power source. Attaching the Grille C 2 K L I Remove the thumbscrews. Remove glass dome. 41787-01 1/11/2006 ...

  • Hunter Fan 41787-01 - page 13

    Connect wiring harness. I C 3 C 4 I Slide light mount over posts. Attach thumbscrews. WARNING: T o reduce the risk of electrical shock, all 3 thumbscrews MUST be properly installed. I J C 5 Install 2 Max 60 Watt A15 bulbs (Not Inc luded). C 6 Screw glass dome into position. Align glass dome and push up. K C 7 L C 8 13 41787-01 1/11/2006 ...

  • Hunter Fan 41787-01 - page 14

    14 T rouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. T o confirm tha t the fan is running, place your hand near the vents to feel the air movement. • T urn power on, replace fuse, or reset breaker . • Check all plug connections to be sure they are secure. • Check the wiring to mak ...

  • Hunter Fan 41787-01 - page 15

    W arranty Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warr anty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to you ...

  • Hunter Fan 41787-01 - page 16

    2500 Frisco Avenue, Memphis, T ennessee 38114 Printed in China 41787-01 1/11/2006 ...

  • Hunter Fan 41787-01 - page 17

    V entilador para baño 81004 V entura con luz LEA y CONSERVE EST AS INSTRUCCIONES 41787-02 1/11/2006 DE SDE Guía de instalación ...

  • Hunter Fan 41787-01 - page 18

    2 41787-02 1/11/2006 DESCONECTE LA ALIMENT ACIÓN ELÉCTRICA Y CIERRE EL P ANEL DE SERVICIO ANTES DE DAR MANTENIMIENTO A LA UNIDAD tc. Retire las cubiertas de las puntas de tornillo precargadas. ADVERTENCIA P ARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRIC A O LESIONES, OBSERVE LO SIGUIENTE: 1. Sólo para uso de ventilación general. No lo utilice para ...

  • Hunter Fan 41787-01 - page 19

    3 x4 * * A B C x2 H E D L 77864-02 F G H I J K 03242-07-133 95047-02-000 74508-03-133 75184-01-133 96258-01/02/03-008 75171-01/02/03-000 x2 * NOT A: Debe estar instalado el manguito de alivio de tensión del cable. No incluido. Conector de cable de 3/8” T ornillos adicionales 96261-01-000 95776-01-000 Check all the parts. If damaged, call 1-888-8 ...

  • Hunter Fan 41787-01 - page 20

    A1 D 4 A2 A3 A6 F A4 A5 Instalación para construcción nueva Retire las puntas de tornillo precargadas hasta que estén a nivel con el lado del alojamiento. Retire el motor/soplador del alojamiento. Retire el tornillo de la cubierta del cableado. Afloje el tornillo que asegura el motor . Retire las cubiertas de las puntas de tornillo precargadas. ...

  • Hunter Fan 41787-01 - page 21

    A7 E A8 D A9 B C A10 D 5/8 1/2 5/8 1/2 A11 OPCIÓN 5 Retire la cubierta del cableado. Expulse el primer tapón metálico de acceso del cableado. Utilice el segundo si es necesario. Introduzca el aliviador de tensiones en el alojamiento y asegúrelo con la arandela. Ubique la correcta marca de profundidad en el borde inferior de la viga, según el e ...

  • Hunter Fan 41787-01 - page 22

    0 A16 D A12 A13 A Motor del ventilador Luz Ver de Interruptor negro 2 (AC) Interruptor negro principal 1 (AC) Blanco Negro Luz Blanco Blanco Cobre desnudo Tie rra A14 *Opción Ventilador y luz principal juntos *Opción Negro 3 3 pasadores pasadores 3 pasadores 2 2 pasadores pasadores 2 pasadores D E A15 F 6 Tire de los alambres por el aliviador de ...

  • Hunter Fan 41787-01 - page 23

    A2 2 C1 Vaya al paso en la página 12 para fijar la rejilla. 0 0 0 0 D A17 G 0 0 0 0 0 G D A18 A20 ENCENDIDO AP AGADO A21 7 A19 H Conecte el cableado del motor a la placa de cubierta del cableado. V uelva a instalar el motor introduciendo las pestañas y levantando a su posición. Asegúrese que los alambres no se pellizquen entre el motor y el alo ...

  • Hunter Fan 41787-01 - page 24

    B3 7.25” 7.75” B1 D B2 Instalación para construcción existente 8 D V entilador existente Recorte una abertura para el alojamiento. Utilice el alojamiento del motor como una plantilla para marcar la posición. Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (7. ...

  • Hunter Fan 41787-01 - page 25

    B4 B5 B8 D B9 B C 9 B6 E B7 E Retire las puntas de tornillo precargadas hasta que estén a nivel con el lado del alojamiento. Retire las cubiertas de las puntas de tornillo precargadas. Retire el tornillo de la cubierta del cableado. Retire la cubierta del cableado. Introduzca el aliviador de tensiones en el alojamiento y asegúrelo con la arandela ...

  • Hunter Fan 41787-01 - page 26

    D B10 B11 2 1 B1 2 D B13 D B14 10 Tire de los alambres a través del aliviador de tensiones y apriete los tornillos de éste. Mueva el alojamiento a su posición encima del techo. Instale el alojamiento en la abertura y asegure apretando los tornillos precargados en la viga. Nota: Instale la caja a nivel con la plancha de yeso (techo). Conecte el d ...

  • Hunter Fan 41787-01 - page 27

    D E F B16 A Motor del ventilador Luz Ver de Interruptor negro 2 (AC) Interruptor negro principal 1 (AC) Blanco Negro Luz Blanco Blanco Cobre desnudo Tie rra B15 *Opción Ventilador y luz principal juntos *Opción Negro 3 3 pasadores pasadores 3 pasadores 2 2 pasadores pasadores 2 pasadores D B17 0 0 0 0 0 G D B18 11 H B19 Conecte el cableado. Insta ...

  • Hunter Fan 41787-01 - page 28

    B20 ENCENDIDO AP AGADO B21 B22 C1 Vaya al paso en la página 12 para fijar la rejilla. 12 J C1 Fijación de la rejilla C2 K L I Pruebe el motor . Si el motor no funciona, verifique la conexión del enchufe. Encienda la fuente de alimentación. Retire los tornillos de mano. Retire el domo de vidrio. 41787-02 1/11/2006 ...

  • Hunter Fan 41787-01 - page 29

    I C3 C4 I I J C5 C6 K C7 L C8 13 Deslice el soporte sobre los postes. Instale los tornillos de mano. ADVERTENCIA: P ara reducir el riesgo de descarga eléctrica, los 3 tornillos de mano DEBEN instalarse apropiadamente. Alinee el domo de vidrio y levante. Instale 2 bombillas A-15 de 60 vatios como máximo (No incluidas). Enrosque el domo de vidrio e ...

  • Hunter Fan 41787-01 - page 30

    14 Solución de problemas Problema: El ventilador no está operando. Solución: • Los ventiladores de baño Hunter son muy silenciosos. Para confi rmar que el ventilador esté funcionando, coloque su mano cerca de los conductos de ventilación para sentir el movimiento del aire. • Encienda la alimentación eléctrica, reemplace el fusible o re ...

  • Hunter Fan 41787-01 - page 31

    Garantía Hunter Fan Company Extractor de aire para baño GARANTÍA LIMIT ADA Hunter Fan Company establece la siguiente garantía limitada al usuario o comprador original de este Extractor de aire par a baño Hunter: Si alguna pieza de su Extractor de aire para baño Hunter (con excepción de las lámpar as de vidrio y las bombillas) falla en cualq ...

  • Hunter Fan 41787-01 - page 32

    41787-02 1/11/2006 2500 Frisco Avenue, Memphis, T ennessee 38114 Impreso en China ...

Manufacturer Hunter Fan Category Ventilation Hood

Documents that we receive from a manufacturer of a Hunter Fan 41787-01 can be divided into several groups. They are, among others:
- Hunter Fan technical drawings
- 41787-01 manuals
- Hunter Fan product data sheets
- information booklets
- or energy labels Hunter Fan 41787-01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hunter Fan 41787-01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hunter Fan 41787-01, service manual, brief instructions and user manuals Hunter Fan 41787-01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hunter Fan 41787-01.

Similar manuals

A complete manual for the device Hunter Fan 41787-01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hunter Fan 41787-01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hunter Fan 41787-01.

A complete Hunter Fan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hunter Fan 41787-01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hunter Fan 41787-01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hunter Fan 41787-01, that we can find in the current document
3. Tips how to use the basic functions of the device Hunter Fan 41787-01 - which should help us in our first steps of using Hunter Fan 41787-01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hunter Fan 41787-01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hunter Fan 41787-01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hunter Fan 41787-01?

Use the form below

If you did not solve your problem by using a manual Hunter Fan 41787-01, ask a question using the form below. If a user had a similar problem with Hunter Fan 41787-01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)