English dropdown-ico

Manual Sony BKP-7933

56 pages 1 mb
Download

Go to site of 56

Summary
  • Sony BKP-7933 - page 1

    S-BUS INTERF ACE BOARD BKP-7933 INST ALLA TION MANUAL 1st Edition (Revised 1) ...

  • Sony BKP-7933 - page 2

    ! W ARNING This manual is intended f or qualified ser vice personnel only . T o reduce the r isk of electric shock, fire or injury , do not perf or m any ser vicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! W ARNUNG Die Anleitung ist n ur für qua ...

  • Sony BKP-7933 - page 3

    1 (E) BKP-7933 Table of Contents Manual Structure Purpose of this manual ........................................................................................ 3 (E) Related manuals ................................................................................................... 3 (E) Trademarks ................................................. ...

  • Sony BKP-7933 - page 4

    2 (E) BKP-7933 1-9. Modification of RCP ........................................................................... 1-39 (E) 1-9-1. Checking ROM Version ..................................................... 1-39 (E) 1-9-2. Modification of RCP-700/701 ............................................ 1-39 (E) 1-9-3. Modification of RCP-720 .............. ...

  • Sony BKP-7933 - page 5

    3 (E) BKP-7933 Purpose of this manual This manual is the installation manual for S-BUS Interface Board BKP-7933. This manual describes the information items necessary when the unit is supplied and installed. Relative manuals Besides this installation manual the following manuals are available for this unit. . . . . . BKP-7933 Maintenance Manual (Av ...

  • Sony BKP-7933 - page 6

    ...

  • Sony BKP-7933 - page 7

    1-1 (E) BKP-7933 Section 1 Installation 1-1. Checking ROM Version When the BKP-7933 is installed in the CNU-700, be sure to check that the ROM versions for IC4 and IC5/AT-89 board of the CNU-700 are Ver. 3.00 or higher. If the ROM needs to be replaced, contact your local Sony Sales Office/Service Center. ROM Version IC4/AT-89 board Ver. 3.00 or hig ...

  • Sony BKP-7933 - page 8

    1-2 (E) BKP-7933 1-4. Setting Switches on the IF-689 Board m . Be sure make the switches settings for the CNU GROUP No. and S-BUS ID No. before turning on the power. It is no use in setting the switches after turning on the power. . Do not change the following switches from their factory default settings. S5-8: OFF S201: 1(ON) Setting of CNU GROUP ...

  • Sony BKP-7933 - page 9

    1-3 (E) BKP-7933 18 7 6 5 4 3 2 1 () 128 64 32 16 8 4 2 S-BUS ID No. Setting example 1 3: 0 0 0 0 0 0 1 0 64: 0 1 0 0 0 0 0 1(ON) 0(OFF) Setting of S-BUS ID No. S12 (S-BUS ID No.) Set the station address for the unit on the standard S-BUS data link. n Set to numbers other than 0, 1 and 255. Factory default setting: 2 18 7 6 5 4 3 2 ( indicates the ...

  • Sony BKP-7933 - page 10

    1-4 (E) BKP-7933 1-5. Installation 1-5-1. Installing the IF-689 Board n The unit is equipped with shielding springs which have sharp edges. Do not touch them with bare hands. Pay careful attention when servicing. 1. Loosen the two screws and remove the front panel of the CNU-700. 2. Insert the IF-689 board in the fourth slot from the top. 3. Attach ...

  • Sony BKP-7933 - page 11

    1-5 (E) BKP-7933 1-5-2. Installing the Rear Panel 1. Remove the two screws and remove the blank panel. 2. Install the rear panel with the two screws instead of the blank panel. B3 x 5 B3 x 5 Blank panel Rear panel 1-5. Installation ...

  • Sony BKP-7933 - page 12

    1-6 (E) BKP-7933 1-6. Connection 1-6-1. Connection Connector/Cable Connection made with the connector panel during installation or service, should be made with the connectors/complete assemblies specified in the following list, or equivalent parts. Connector Name Connection Connectors Conection Cable REMOTE S-BUS BNC(75 Z ) BELDEN 8281 * 1 1-569-37 ...

  • Sony BKP-7933 - page 13

    1-7 (E) BKP-7933 1-6-2. Connector Input/Output Signals REMOTE S-BUS BNC 75 Z , 1.0 Vp-p I/O PORT (D-sub 50P, Female) (External view) Pin No. I/O Specifications 1 IN/OUT EXTO 0 2 IN/OUT EXTO 3 3 IN/OUT EXTO 6 4 IN EXTI 1 5 IN EXTI 4 6 IN EXTI 7 7— N C 8— N C 9 OUT EXT-AN 0 10 OUT EXT-AN 3 11 OUT EXT-AN 6 12 — NC 13 — NC 14 — NC 15 OUT + 28 ...

  • Sony BKP-7933 - page 14

    1-8 (E) BKP-7933 1-6-3. Notes on Connection To connect the devices to the S-BUS line, refer to Section 1-6-4 and following precautions. . The cable length of one S-BUS line is a maximum of 500 m (when a BELDEN 8281 or the equivalent is used). . Be sure to terminate the BNC connector (T bridge) attached to the last machine of the S-BUS line with a 7 ...

  • Sony BKP-7933 - page 15

    1-9 (E) BKP-7933 CCA-5 CABLE CCA-5 CABLE CCA-5 CABLE CCA-5 CABLE CCA-5 CABLE CCA-5 CABLE CCA-5 CABLE TRIAX  CABLE 1 CAM 2 CAM 3 CAM TRIAX  CABLE TRIAX  CABLE CNU  CHARACTER DIGITAL VIDEO INTERFACE UNIT PFV-D10 ROUTING SWITCHER CONTROLLER BOARD BKPF-R70 DIGITAL VIDEO  ROUTING SWITCHER  DVS-V6464B CONTROL TER ...

  • Sony BKP-7933 - page 16

    1-10 (E) BKP-7933 1-7. Setting Up n The description in this section assumes that the BKPF-R70 is used as the primary station. 1-7-1. Outline Calling the Menu Display of the Secondary Station First, call the menu display of the secondary station that is connected to the S-BUS of the primary station. Procedure 1. Call the SETUP MENU of the primary st ...

  • Sony BKP-7933 - page 17

    1-11 (E) BKP-7933 12131415 1 1 12 33 33 44 44 45 45 56 56 57 57 58 68 1024 1024 ROUTER  PIX1 CAMERA-CCU CCU-RCP MSU2 MSU1 SOURCE No. DESTINATION No. LEVEL-1 ROUTER PIX3 ROUTER PIX2(MSU2) ROUTER PIX2(MSU1) Saving the Setup Data Press [Ctrl] - [E] to validate and save the setup data and to return to the BKP-7933 menu display. Press [Ctrl] - [D] to ...

  • Sony BKP-7933 - page 18

    1-12 (E) BKP-7933 1-7-2. Linking the RCP Assignment and VE Monitor Selection Description of Operation Set the menu as follows when you want to link the RCP assignment with the VE monitor selection. If this setting is executed, by changing the RCP assignment on the MSU side, the VE monitor that corresponds to the RCP is automatically switched at the ...

  • Sony BKP-7933 - page 19

    1-13 (E) BKP-7933 CCA-5  CABLE CCA-5  CABLE REMOTE RCP/CNU REMOTE CCU/CNU REMOTE CCU/CNU REMOTE CCU/CNU REMOTE CCU/CNU CCU 1 to 6 RCP 1 to 6 MSU IN 1 OUT 1 OUT 2 OUT 6 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 SERIAL OUTPUT REMOTE RCP/CNU SERIAL OUTPUT SERIAL OUTPUT REMOTE RCP/CNU DIGITAL ROUTING  SWITCHER? ...

  • Sony BKP-7933 - page 20

    1-14 (E) BKP-7933 Setting from the S-BUS Primary Station 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) K: RES ...

  • Sony BKP-7933 - page 21

    1-15 (E) BKP-7933 1-7-3. Linking the MSU Camera Selection and the VE Monitor Selection Description of Operation Set the menu as follows when you want to link the MSU camera selection with the VE monitor selection. If this setting is executed, when the MSU camera select button is pressed, the video signal of the selected camera can be output to the ...

  • Sony BKP-7933 - page 22

    1-16 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX or WF connector (PIX 2 or WF 2 connector  for the CCU-700A series) CCA-5  CABLE CCA-5  CABLE REMOTE RCP/CNU REMOTE CCU/CNU CCU 1 to 6 MSU IN 1 OUT 13 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 SERIAL OUTPUT REMOTE RCP/CNU SERIAL OUTPUT ...

  • Sony BKP-7933 - page 23

    1-17 (E) BKP-7933 Setting from the S-BUS Primary Station 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) K: RES ...

  • Sony BKP-7933 - page 24

    1-18 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector CCA-5  CABLE CCA-5  CABLE REMOTE RCP/CNU REMOTE CCU/CNU REMOTE CCU/CNU REMOTE CCU/CNU REMOTE CCU/CNU CCU 1 to 6 RCP 1 to 6 MSU IN 1 OUT 15 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 IN 13 SERIAL OUTPUT REMOTE RC ...

  • Sony BKP-7933 - page 25

    1-19 (E) BKP-7933 SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) K: RESET TO DEFAULT TABLE         MAINTENANCE COMMAND  Z: BKP-7933 CONFIGURATION  ? ...

  • Sony BKP-7933 - page 26

    1-20 (E) BKP-7933 Linking the Preview Monitor Selection with MSU and VCS 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATIO ...

  • Sony BKP-7933 - page 27

    1-21 (E) BKP-7933 Changing the Operation Mode of the RCP PREVIEW Switch The operation mode of the RCP PREVIEW switch can be changed on the CNU-700 character display. Use the switches on the AT board inside the CNU-700 for this setting. 1. Set the MODE switch to 5. The message “INTERNAL MODE SETTING” appears on the character monitor display. 2. ...

  • Sony BKP-7933 - page 28

    1-22 (E) BKP-7933 1-7-5. Executing RCP Assignment from Equipment Other Than MSU Description of Operation Set the menu as follows when you want to execute RCP assignment from equipment other than MSU. When this setting is executed, a maximum of 96 x 96 CCU-RCP matrix can be set in the matrix space of the S-BUS. The RCP assignment can be set from a r ...

  • Sony BKP-7933 - page 29

    1-23 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector CCA-5  CABLE CCA-5  CABLE REMOTE RCP/CNU REMOTE CCU/CNU REMOTE CCU/CNU REMOTE CCU/CNU REMOTE CCU/CNU CCU 1 to 6 RCP 1 to 6 MSU IN 1 OUT 1 OUT 2 OUT 6 REMOTE 1 REMOTE S-BUS REMOTE REMOTE 3 IN 2 IN 6 SERIAL OUTPUT ...

  • Sony BKP-7933 - page 30

    1-24 (E) BKP-7933 SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) K: RESET TO DEFAULT TABLE         MAINTENANCE COMMAND  Z: BKP-7933 CONFIGURATION  ? ...

  • Sony BKP-7933 - page 31

    1-25 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector CCA-5  CABLE CCA-5  CABLE REMOTE RCP/CNU REMOTE CCU/CNU CCU 1 to 6 MSU IN 1 OUT 13 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 SERIAL OUTPUT REMOTE RCP/CNU SERIAL OUTPUT SERIAL OUTPUT REMOTE RCP/CNU DIGITAL RO ...

  • Sony BKP-7933 - page 32

    1-26 (E) BKP-7933 Setting from the S-BUS Primary Station 1. Select the menu item “C:SET UNIT LOCATION (MSU)” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) K: RESE ...

  • Sony BKP-7933 - page 33

    1-27 (E) BKP-7933 1-7-7. Changing the Camera Assignment Virtually Description of Operation Set the menu as follows when you want to change the camera assignment virtually. When this setting is executed, the camera assignment can be changed virtually without changing the cable connection be- tween the cameras and CCUs. However, the tally numbers and ...

  • Sony BKP-7933 - page 34

    1-28 (E) BKP-7933 Displaying the SOURCE NAME on the CNU Character Display 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATI ...

  • Sony BKP-7933 - page 35

    1-29 (E) BKP-7933 1-7-8. Using the Tally System Description of Operation Set the menu as follows when you want to construct a tally system using the S-BUS. When this setting is executed, the red tally and the green tally signals are accepted through the S-BUS and are output to the corresponding CCU and camera in the form of command signals. Do not ...

  • Sony BKP-7933 - page 36

    1-30 (E) BKP-7933 Setting from the S-BUS Primary Station 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2    MODIFICATION COMMAND  A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) K: RES ...

  • Sony BKP-7933 - page 37

    1-31 (E) BKP-7933 5. Return to the previous screen by pressing [Ctrl] - [E] , and select the menu item “H:BKP-7933 MODE”. BKP-7933 CONFIGURATION BKP-7933 V1.00 STATION NUMBER 2      S-BUS CONFIGURATION  A: ROUTER PIX1 ASSIGN B: ROUTER WF1 ASSIGN C: ROUTER PIX2 ASSIGN D: ROUTER WF2 ASSIGN E: ROUTER PIX3 ASSIGN F: RO ...

  • Sony BKP-7933 - page 38

    1-32 (E) BKP-7933 1-7-9. Displaying the Self-diagnostic Information on the Terminal Description of Operation Set the menu as follows when you want to display the self-diagnostic information on the display. When this setting is executed, the status of the self-diagnostics is displayed on the terminal when the self- diagnostic information of the came ...

  • Sony BKP-7933 - page 39

    1-33 (E) BKP-7933 1-7-10. Returning the Setups of the MODIFICATION COMMAND to the Factory Default Values 1. Select “K: RESET TO DEFAULT TABLE” using the cursor key and press [ENTER] . 2. The message “Reset to Default table?” appears in the bottom right of the screen. Select “Y” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 ...

  • Sony BKP-7933 - page 40

    1-34 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector CCA-5  CABLE CCA-5  CABLE CCA-5  CABLE REMOTE RCP/CNU REMOTE CCU/CNU CCU 1 to 12 MSU AUX 1 AUX 1 IN 1 OUT 25 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 12 IN 13 IN 24 IN 14 SERIAL OUTPUT REMOTE RCP/CNU SERIAL OUTPUT ...

  • Sony BKP-7933 - page 41

    1-35 (E) BKP-7933 1-8. Data Backup/Restore m . The description in this section assumes that BKPF-R70 is used as the primary station. . The setup data of the unit is backed up and restored by using the BZR-10 (software for data backup) supplied with the BKPF-R70. . In this section, a lower-case letter is used in the sample screens. If you want, you ...

  • Sony BKP-7933 - page 42

    1-36 (E) BKP-7933 1-8-2. Data Backup (Uploading) n For the details of the menu screen and the setting procedure in terminal mode, refer to the installation manual for system setup of ROUTING SWITCHER SYSTEM. For obtaining the installation manual of ROUTING SWITCHER SYSTEM, contact your local Sony Sales Office/Service Center. 1. Install the BZR-10 s ...

  • Sony BKP-7933 - page 43

    1-37 (E) BKP-7933 13. Type “1” at the Function menu. (“1. RECEIVE” is selected.) The display changes to the Execution menu screen. 14. To back up the data of the BKP-7933, type “2”. (“2. The data of secondary stations” is selected.) The data is backed up in the FD. 15. Type “9” twice. (“9. Quit” is selected.) The backup mode ...

  • Sony BKP-7933 - page 44

    1-38 (E) BKP-7933 1-8-3. Data Restore (Downloading) After the BZR-10 is installed according to Section 1-8-1, perform the following procedures. 1. Insert the FD on which the data is stored in an FD drive of the personal computer. 2. Type as follows. C:> a: " A > * " Type “a” or “a1”. n “a” or “a1” is the command to ...

  • Sony BKP-7933 - page 45

    1-39 (E) BKP-7933 1-9. Modification of RCP The video on the preview monitor can be selected by the PREVIEW switch of the RCP-700/701/720/721/ 730/731. (Refer to section 1-7-4 for details.) However, version check of the ROM that is installed in the board of the RCP side, and modification of the board in the RCP are required. n If you want to switch ...

  • Sony BKP-7933 - page 46

    1-40 (E) BKP-7933 1-9. Modification of RCP SW-752 BOARD SW-752 BOARD ...

  • Sony BKP-7933 - page 47

    1-41 (E) BKP-7933 1-9-3. Modification of RCP-720 Required Part Description Sony P/N Q'ty Jumper wire __ Modification Procedure 1. Connect the two jumper wires by soldering. (SW-754 board) Between pin-6/CN3 and D25 cathode ( 1 ) Between pin-5/CN3 and pin-2/S24 ( 2 ) 2. Disconnect CN101/CN-1187 board. Setting Switch on MPU-92 Board S4-7/MPU-79 b ...

  • Sony BKP-7933 - page 48

    1-42 (E) BKP-7933 1-9-4. Modification of RCP-721 Required Parts Description Sony P/N Q'ty Resistor, Chip Metal 82 Z 1-216-625-11 1 Jumper wire __ Modification Procedure (SW-752 Board) 1. Remove the resistors R10 and R55/SW-755 board. 2. Connect a metal resistor 82 Z to the soldering land of R10, by soldering. 3. Connect the four jumper wires b ...

  • Sony BKP-7933 - page 49

    1-43 (E) BKP-7933 1-9-5. Modification of RCP-730/731 Required Parts Description Sony P/N Q'ty Resistor, Chip Metal 0 Z 1-216-295-11 3 Resistor, Chip Metal 82 Z 1-216-625-11 1 Modification Procedure (SW-893 Board) 1. Remove soldering of R1, R2, R3 and R12. 2. Connect metal resistors 0 Z to the soldering land of R4, R6 and R7 by soldering. 3. Co ...

  • Sony BKP-7933 - page 50

    1-44 (E) BKP-7933 1-10. Using the BKP-7933 in the HD System Connecting Peripheral Equipment 1-10-1. Controlling the Routing Switcher via the RS-422A Interface The routing switcher can be controlled via the RS-422A interface. Modify the AT-89 board of the CNU- 700, replace ROM of the MSU and make the MSU assignment referring to the following descrip ...

  • Sony BKP-7933 - page 51

    1-45 (E) BKP-7933 Modification of AT-89 Board 1. Connect a jumper wire between B7 pin/CN2 and B9 pin/CN2 of the AT-89 board of the CNU-700 by soldering. 2. Remove the six screws and remove the rear panel. Remove the harness that is connected to the connector CN12 on the MB-562 board and the connector CN15 on the CN-1001 board. Connect the RS-422 ha ...

  • Sony BKP-7933 - page 52

    1-46 (E) BKP-7933 1-10-2. Controlling a Waveform Monitor A waveform monitor can be controlled from the MSU via the I/O PORT connector of the BKP-7933, by setting the switches on the IF-689 board of the BKP-7933. n The following setting is effective to control a waveform monitor from the MSU that is connected to the IF-480 board of the CNU-700 in wh ...

  • Sony BKP-7933 - page 53

    1-47 (E) BKP-7933 1-10. Using the BKP-7933 in the HD System RECALL system 1 1 2 14 25 24 23 22 21 20 19 18 17 13 2 3 34 35 18 17 50 32 33 19 20 RECALL 1 RECALL 2 RECALL 3 RECALL 4 RECALL 5 RECALL 6 RECALL 7 RECALL 8 50P CONNECTOR (MALE) (WIRING SIDE) 25P CONNECTOR (MALE) (WIRING SIDE) GND Connection The wiring diagram of the cable connecting ...

  • Sony BKP-7933 - page 54

    1-48 (E) BKP-7933 1-11. Description on Internal Indicators Ref.No. Indicator Name Color Status D1 + 5 V Green Lights when +5 V is normally supplied to the IF-689 board D402 S-BUS RX Green Lights when the serial data is received from the REMOTE S-BUS connector D403 S-BUS TX Green Lights when the serial data is transmitted to the REMOTE S-BUS connect ...

  • Sony BKP-7933 - page 55

    The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenan ...

  • Sony BKP-7933 - page 56

    Printed in Japan Son y Cor poration 2000. 5 08 Communication System Solutions Netw ork Company ©1998 BKP-7933 (SY) J, E 3-201-655-02 ...

Manufacturer Sony Category Network Router

Documents that we receive from a manufacturer of a Sony BKP-7933 can be divided into several groups. They are, among others:
- Sony technical drawings
- BKP-7933 manuals
- Sony product data sheets
- information booklets
- or energy labels Sony BKP-7933
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sony BKP-7933.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sony BKP-7933, service manual, brief instructions and user manuals Sony BKP-7933. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sony BKP-7933.

Similar manuals

A complete manual for the device Sony BKP-7933, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sony BKP-7933 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sony BKP-7933.

A complete Sony manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sony BKP-7933 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sony BKP-7933, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sony BKP-7933, that we can find in the current document
3. Tips how to use the basic functions of the device Sony BKP-7933 - which should help us in our first steps of using Sony BKP-7933
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sony BKP-7933
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sony BKP-7933 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sony BKP-7933?

Use the form below

If you did not solve your problem by using a manual Sony BKP-7933, ask a question using the form below. If a user had a similar problem with Sony BKP-7933 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)