English dropdown-ico

Manual Troy-Bilt Storm 9528

28 pages Not applicable
Download

Go to site of 28

Summary
  • Troy-Bilt Storm 9528 - page 1

    m _ _ _ ,_m_ r Operator's Manual Two-Stage Snow Thrower 8526--Storm 9528--Storm J IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system ...

  • Troy-Bilt Storm 9528 - page 2

    Content Important Safe Operation Practices Assembling Your Snow Thrower Know Your Snow Thrower Operating Your Snow Thrower Making Adjustments TABLE OF CONTENTS Page 3 6 8 10 13 Content Page Maintaining Your Snow Thrower 15 Servicing Your Snow Thrower 15 Troubleshooting 20 Illustrated Parts List 22 Warranty Back Cover FINDING MODEL NUMBER This Opera ...

  • Troy-Bilt Storm 9528 - page 3

    SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. DANGER: This machine was built to be operated according to the rules for safe operation in this manual. ...

  • Troy-Bilt Storm 9528 - page 4

    Operation 1. Do not puthands or feetnear rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury. 3. The control levers must operate ...

  • Troy-Bilt Storm 9528 - page 5

    YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Do not modify engine To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at uns ...

  • Troy-Bilt Storm 9528 - page 6

    SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position (standing directly behind the snow thrower, facing the handle panel). IMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel). Refe ...

  • Troy-Bilt Storm 9528 - page 7

    NOTE: If the flange keepers will not easily click into place, use the palm of your hand to apply swift, firm pressure to the back of each. 5. Remove the clevis pin and hairpin clip from the upper portion of the chute mast. • Position the control head over the chute mast and rear portion of the chute assembly. • Re-insert the clevis pin and secu ...

  • Troy-Bilt Storm 9528 - page 8

    SECTION 3: KNOW YOUR SNOW THROWER Drive Control Electric Starter Button Gas Cap Oil Fill Chute Assembly Clean-out_ Tool Shift Lever Chute Directional Control / Auger Control f Engine Controls Electric Starter Outlet Ignition Key Spark Plug Cover Recoil Starter Handle Choke Control Augers Skid Shoe Throttle Control ,J ,_ WARNING: Read, understand, a ...

  • Troy-Bilt Storm 9528 - page 9

    Auger Control f The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Drive Control The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive. Release to stop. Chute Directional ...

  • Troy-Bilt Storm 9528 - page 10

    SECTION 4: OPERATING YOUR SNOW THROWER Before Starting ,_ WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. Gas & Oil Fill-Up Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separately with your snow thrower. Read instructions care ...

  • Troy-Bilt Storm 9528 - page 11

    • Pull the starter handle with a firm, rapid stroke. IMPORTANT: Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. • As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position a ...

  • Troy-Bilt Storm 9528 - page 12

    • Retighten the hex jam nut. See Figure 1. • Repeat Auger Control Test to verify proper adjustment has been achieved. ii ', Figure 1 Chute Clean-Out Tool The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, procee ...

  • Troy-Bilt Storm 9528 - page 13

    SECTION 5: MAKING ADJUSTMENTS _, WARNING: Never attempt to make any adjustments while the engine is running, except where specified in operator's manual. ShiftRod Adjustment If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures to the right and adjust the shift rod as follows: 1. Place the shift lever in th ...

  • Troy-Bilt Storm 9528 - page 14

    Drive Control When the drive control is released and in the disengaged "up" position, the cable should have very little slack. It should NOT be tight. Check the adjustment of the drive control as follows: 1. With the drive control released, push the snow thrower gently forward. The unit should roll freely. 2. Engage the drive control and ...

  • Troy-Bilt Storm 9528 - page 15

    SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Engine Refer to the separate Tecumseh Engines manual packed with your unit for all engine maintenance. Lubrication Engine Refer to the separat ...

  • Troy-Bilt Storm 9528 - page 16

    i ' /' / ....... / / i is .......... i i' Auger BeltReplacement To remove and replace your snow thrower's auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap ...

  • Troy-Bilt Storm 9528 - page 17

    / 7 / i DriveBelt Replacement To remove and replace your snow thrower's auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefully pivot the snow thrower u ) and fo ...

  • Troy-Bilt Storm 9528 - page 18

    Friction WheelRemoval If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment on page 14 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary • Place the ...

  • Troy-Bilt Storm 9528 - page 19

    Augers • The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Refer to Figure 6. • If the augers will not turn, check to see if the pins have sheared. One set of replacement shear pins has been provided wit ...

  • Troy-Bilt Storm 9528 - page 20

    SECTION 8: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Engine fails to start Fuel tank empty, or stale fuel. Blocked fuel line. Choke control not in ON position Faulty spark plug. Ignition key not present. Spark plug wire disconnected. Engine not primed. Engine runs erratic Unit running on CHOKE. Blocked fuel line or stale fuel. Water or dirt ...

  • Troy-Bilt Storm 9528 - page 21

    NOTES 21 ...

  • Troy-Bilt Storm 9528 - page 22

    SECTION 9: PARTS LIST 15 4O 16 25 5 30 21 10 19 18 22 13 2O 36 47 17 12 29 39 "15 / 22 ...

  • Troy-Bilt Storm 9528 - page 23

    Style Q REF. PART NO. NO. 1 631-04127 2 631-04133 3 631-04134 4 684-04105 5 684-04106 6 710-04326 7 710-04354 8 710-1026 9 710-1233 10 711-04287 11 711-0677 12 712-04064 13 712-04081A 14 714-0104 15 720-0274 16 720-04039 17 725-04213 18 725-04214 19 725-1649 20 726-0470 21 731-04894 22 731-04896 23 732-0193 24 732-04219 25 732-04238 26 735-0199A 27 ...

  • Troy-Bilt Storm 9528 - page 24

    Style Q 18 7O 7 38 26 7 _17 3 22 41 34 j 30 32 56 2 49 68 _2_ 62 5458 _ 61 4 64 65 8 6 e 35 7 24 ...

  • Troy-Bilt Storm 9528 - page 25

    Style Q REE PART NO. NO. 1 731-2643 2 684-04057 3 710-0347 4 710-0451 5 710-0703 6 710-0726 7 712-04063 8 712-04064 9 712-04065 10 714-0507 11 725-0157 12 726-04012 13 731-04705 14 732-0611 15 736-0174 16 736-0463 17 731-04869 18 738-0143 19 738-0281 20 738-04124 21 741-0245 22 741-0309 23 756-0981A 24 790-00075 25 790-00080 26 631-04132 27 684-041 ...

  • Troy-Bilt Storm 9528 - page 26

    Style Q 13 4O 58 53 57 47 7 20 24 ¢_/,/ 30 36 56 24 50 7 48 14 4 41 60 49 55 52 21 58 27 62 26 61 / 32 38 25 67 66 26 ...

  • Troy-Bilt Storm 9528 - page 27

    Style O RER PART NO. NO. 1 517-04026 2 517-04025 3 B56-0012A 4 584-04066 5 584-04045 6 584-04139 7 710-0627 8 710-0788 90 710-1652 711-04246A 11 712-0711 12 714-0161 13 716-0231 14 716-0136 15 717-04129a 16 i717-04137a 17 684-04014A 18 726-0221 19 732-0264 20 736-0242 21 736-04161 22 736-0300 23 736-0105 24 736-0287 25 634-04147 634-04148 26 731-04 ...

  • Troy-Bilt Storm 9528 - page 28

    MANUFACTURER'S LIMITED WARRANTY FOR: ® m The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/or its territories and possessions ...

Manufacturer Troy-Bilt Category Snow thrower

Documents that we receive from a manufacturer of a Troy-Bilt Storm 9528 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- Storm 9528 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt Storm 9528
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt Storm 9528.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt Storm 9528, service manual, brief instructions and user manuals Troy-Bilt Storm 9528. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt Storm 9528.

Similar manuals

A complete manual for the device Troy-Bilt Storm 9528, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt Storm 9528 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt Storm 9528.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt Storm 9528 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt Storm 9528, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt Storm 9528, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt Storm 9528 - which should help us in our first steps of using Troy-Bilt Storm 9528
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt Storm 9528
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt Storm 9528 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt Storm 9528?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt Storm 9528, ask a question using the form below. If a user had a similar problem with Troy-Bilt Storm 9528 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)