Manual Honeywell P520

16 pages 1.18 mb
Download

Go to site of 16

Summary
  • Honeywell P520 - page 1

    USER MANU AL Put Bar Code Here 66-2066-01 P520 Signal Pr ocessor APPLICATION The Hone ywell P520 is a rac k mounting signal proc essor that is compatible with viewing heads in the S5XX and S55XB/BE series. These include models S506, S509 , S511 and S512 , and the advanced viewing head seri es models S550B/BE, S552B/BE and S556B/BE. There is only on ...

  • Honeywell P520 - page 2

    P520 SIGNAL PROCESSOR 66-2066—0 1 2 Fig. 1. P520 front faceplate dim ensions. Fig. 2. P520 side view dimensions. INSTALLATION When Installing this Product… 1. Read these instr uctions carefully . F ailure to follo w them could damage the pro duct or cause a hazardo us condition. 2. Check the r atings given in the instructions and on the product ...

  • Honeywell P520 - page 3

    P520 SIGNAL PROCESSOR 3 66-2066—01 3. Install a ground wire from the igni tion transformer case to the igniter assembly . 4. Ensure all igniter wires and cables show no signs of wear . Replace any igniter cab les or wires that are fra yed or crac ked. 5. The viewing head must be elec tr ically isolated from the bu r ner front. a. Electrical isola ...

  • Honeywell P520 - page 4

    P520 SIGNAL PROCESSOR 66-2066—0 1 4 Fig. 3. Rear PCB terminal wiring. P olar ity must be observed when wiri ng this connection (the positive terminal is o n the top). This is an is olated input, so two wires are required. Any DC voltage from 7.5 to 30 may be used. The cu rrent required will depend upon the voltage, because this is a photocoupler ...

  • Honeywell P520 - page 5

    P520 SIGNAL PROCESSOR 5 66-2066—01 Wiring the Vie wing Head Wiring of the viewing head is made to the ter minals on the rear backplane PCB. These termina ls are described as follows: Fig. 4 and 5 show f o ur-conductor cable to the viewing head. Note that the flame signal wi re going to ter minal SIG is shielded, and the shield is ter minated at b ...

  • Honeywell P520 - page 6

    P520 SIGNAL PROCESSOR 66-2066—0 1 6 IMPORTANT Source impedance resistor required at the si gnal processor between SC and SIG GND ter minals for proper signal trans- mission. F or resistor value, ref er to the Wir ing of the Viewing Head section. Fig. 5. Wiring connect ions for S550B E, S552BE and S556BE viewing heads. A source impedance resistor ...

  • Honeywell P520 - page 7

    P520 SIGNAL PROCESSOR 7 66-2066—01 V erifyin g the v alidity of the ga in code rece iv ed is one o f the tasks performed by the processor in the viewing heads. The self-check pulse from the signal p rocessors is a 100ms-wide, 20V to 24V pulse with two notche s or breaks in it. The position of each of the two notches communicates a gain cod e one ...

  • Honeywell P520 - page 8

    P520 SIGNAL PROCESSOR 66-2066—0 1 8 change the display ed value. Once the desired value is display ed, press the ST ORE button. When the set point is stored, four dashes are display ed momen tarily , indicating that the new v alue was stored into the EEPROM. Illogical settings are not accepted; A display of f our “E’ s” when the ST ORE butt ...

  • Honeywell P520 - page 9

    P520 SIGNAL PROCESSOR 9 66-2066—01 SETUP AND ADJUSTMENT PR OCEDURES Sighting Adjustment Bef ore making definitiv e settings (i.e., estab lishing the set points) for FLAME ON/OFF , the us er must f irst opti mize the sighting of the viewing head. F o r detailed mounting and sighting information, refer to the applicab le literature for the viewing ...

  • Honeywell P520 - page 10

    P520 SIGNAL PROCESSOR 66-2066—0 1 10 TR OUBLESHOO TING Module Comm unications The P520 communicates with any host computer that has a USB por t and suppor ts ASCII character code transmission at 4800 baud (or , in current revisions of the processor chip, at 4800 or 9600 ba ud). The baud rate i s displayed with the module address in the current ve ...

  • Honeywell P520 - page 11

    P520 SIGNAL PROCESSOR 11 66-2066—01 T o change or check the station number of the P520, proceed as f ollows: 1. Press and hold th e Reset button for 4 seconds. 2. The 4 LED digits will show the baud rate and the station number . The 2 leftmost digits are the baud rate (96 or 48); the 2 righ tmost digits are station number fro m (0 to 63). 3. Pres ...

  • Honeywell P520 - page 12

    P520 SIGNAL PROCESSOR 66-2066—0 1 12 address 2). T o change to 9600 baud, in crease the display past 4863. The ne xt display will be 9600, which is 9600 baud, address 0. Then increase the display fur ther to the desired address. T o retur n to 4800 ba ud, reduce the display below 9600, and set the desired address. Fig. 6. T ypical Communications ...

  • Honeywell P520 - page 13

    P520 SIGNAL PROCESSOR 13 66-2066—01 Fig. 8. P520 with S550B/BE programming flowchart. PRESS BOT H A & B BU TTO N S “CAL ? ” CALI BR ATE VI EW ING HEAD? N N “CAL U” AUTO ADJ UST UV GAIN? N NO RMAL O PERA TIO N C AL IBRAT E U V Y Y C AL IBRAT E I R Y “AUNN” ADJUST U V G AIN 0- 99 Y NO RMAL O PERA TIO N N Y N DIS CARD CHA NGE S NORMA ...

  • Honeywell P520 - page 14

    P520 SIGNAL PROCESSOR 66-2066—0 1 14 Fig. 9. P520 with S552B/BE programming flowchar t. PRESS BOT H A & B BU TTO N S “CAL ?” CALI BR ATE VI EW ING HEAD? N N NO RMAL O PERA TIO N Y CA LI B R A TE IR Y Y NORMAL OPERATION N NO RMAL O PE RAT ION Y KEEP NEW FIL TER SELE CT IO N “ARF N” ADJ UST IR FI LTER 1- 8 “ANNN” ADJ UST IR GAI N 0- ...

  • Honeywell P520 - page 15

    P520 SIGNAL PROCESSOR 15 66-2066—01 Fig. 10. P520 with S556B/ BE programming flo wchar t. PRESS BOT H A & B BU TTO N S “CAL ?” CALI BR ATE VI EW ING HEAD? N N “CAL U” AUT O A DJUST UV GAIN? NORMAL OPERATION C AL IBRAT E U V Y Y “AU NN” ADJ UST UV GAIN 0- 99 Y NO RMAL O PE RAT ION PROGRAMMING FLOWCHART FOR P520 WITH S556B/BE Y N DI ...

  • Honeywell P520 - page 16

    P520 SIGNAL PROCESSOR Automation and Co ntrol Solutions Honeywell Internationa l Inc. 1985 Douglas Drive North Golden Valley, MN 55422 customer.honeywell.com ® U .S. Re gistered T rademark © 2012 Hone ywell International Inc. 66-2066—01 M.S. 10- 12 Printe d in United St ates ...

Manufacturer Honeywell Category Stereo System

Documents that we receive from a manufacturer of a Honeywell P520 can be divided into several groups. They are, among others:
- Honeywell technical drawings
- P520 manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell P520
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell P520.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell P520, service manual, brief instructions and user manuals Honeywell P520. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell P520.

A complete manual for the device Honeywell P520, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell P520 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell P520.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell P520 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell P520, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell P520, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell P520 - which should help us in our first steps of using Honeywell P520
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell P520
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell P520 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell P520?

Use the form below

If you did not solve your problem by using a manual Honeywell P520, ask a question using the form below. If a user had a similar problem with Honeywell P520 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)