Manual Philips 5900

160 pages 3.1 mb
Download

Go to site of 160

Summary
  • Philips 5900 - page 1

    AXIS 5900 User’s Manual 1 AXIS 5900 Network Print Servers User’s Manual ...

  • Philips 5900 - page 2

    2 AXIS 5900 User’s Manual Regulatory Information Safety Notices Take some time to read through the safety notice s before installing the print serv er. Please observe all safety m arkings and instructions when using this product. Important: Observe “Important:” in the text to avoid operational im pairment. Do not proceed until you have fully ...

  • Philips 5900 - page 3

    AXIS 5900 User’s Manual 3 Radio Trans mission Regu latory Informati on The channel must be set ac cording to the radio frequency r equirements in your cou ntry: * (France) outdoor use permitted on pr ivate property with prior authorization Tested to comply with FCC Standards FOR HOME OR OFFICE USE. This product must be installed and used in s tri ...

  • Philips 5900 - page 4

    4 AXIS 5900 User’s Manual Table of Contents Section 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Supported Environments . . . . . . . . . . . . . . . . . . . . . . . . 6 About Axis . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 5

    AXIS 5900 User’s Manual 5 Section 6 Adding Printers in NetWare . . . . . . . . . . . . . . . . . . . . . . . . . 49 Setup using NDPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Setup using iPrint . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Basic Setup with AXIS NetPilot . . . . . . . . . . . . . . . . . . 70 Advanced ...

  • Philips 5900 - page 6

    Introduction 6 AXIS 5900 User’s Manual Section 1 Introduction Thank you for purchasing the AX IS 5900. This product has been developed to connect your printers an ywhere in your ne twork, allowing all network users access to shared prin ter resour ces. The AXIS 5900 can be installed either as an IEEE 802.11b wireless print server or as an Etherne ...

  • Philips 5900 - page 7

    Introduction AXIS 5900 User’s Manual 7 Support Services Should you require any technical assi stance, please contact your Axis reseller. If your questions cannot be answered immediately, your Axis reseller will forward your queries thro ugh the appropriate channels to ensure a rapid response. If you are connected to the I nternet, you can: • Do ...

  • Philips 5900 - page 8

    Product Overview 8 AXIS 5900 User’s Manual Section 2 Product Overview Package Contents Verify that nothing is missing from the AXIS 5900 print server package by using the check list below. Please contact your dealer if anything is missing or damaged. All packing materials are recyclable. Caution! AXIS Network Product CD The AXIS Network Product C ...

  • Philips 5900 - page 9

    Product Overview AXIS 5900 User’s Manual 9 Start-up procedures for UNIX, OS/2 and Mac OS Using your preferred file manager application, navigate to the CD root directory and click index.ht m Latest Versions The latest version of Axis documentation, software and firmware is available on www.axis.com Physical Description AXIS 5900 Underside label o ...

  • Philips 5900 - page 10

    Product Overview 10 AXIS 5900 User’s Manual Test Button The test button is used for: • Printing a test page to check the connection to the printer. • Printing the parameter list show ing the print server settings. • Performing a Factory Default of the pr int server, which will restore most of the parameters and settings to factory default v ...

  • Philips 5900 - page 11

    Product Overview AXIS 5900 User’s Manual 11 Features and Benefits Reliability The AXIS 5900 print server provides high performance and reliability combined with low power consumption. The electronic circuits are based on the AXIS ETRAX 100 LX chip, whic h comprises an integrated 32 bit RISC processor an d associated network controllers. Flexibili ...

  • Philips 5900 - page 12

    Product Overview 12 AXIS 5900 User’s Manual Monitoring The internal Axis Ne twork Print Server Web pages and the AXIS ThinWizard software allow you to co ntinuously monitor printer status. The Web pages are used to monito r single Axis units and AXIS ThinWizard can be used to monitor multiple Axis units. The AXIS 5900 supports SNMP for remote mon ...

  • Philips 5900 - page 13

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 13 Section 3 Basic Installation (Wired & Wireless) Connecting the Hardware 1. Make sure that your printer is switched off and that the Power Adapter external is disconnected . 2. Locate the serial number, found on th e underside label of the print server, and write it down. Yo ...

  • Philips 5900 - page 14

    Basic Installation (Wired & Wireless) 14 AXIS 5900 User’s Manual Installation Overview Select the appropriate method to es tablish a connection between the workstation / laptop and the Axis Ne twork Print Server. The following descriptions provide an overview of the installation procedures: • “Setting up Using the Ethernet Interface” on ...

  • Philips 5900 - page 15

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 15 Setting up ove r the WLAN Before you begin, configure the WLAN settings on your workstation / laptop as described below (refer to th e user documentation of your WLAN network interface for instructions): •S e l e c t ad hoc mode. •S e t t h e SSID to AXIS followed by the la ...

  • Philips 5900 - page 16

    Basic Installation (Wired & Wireless) 16 AXIS 5900 User’s Manual Assigning an IP Address to the Print Server Before you Start If you have a DHCP server on your ne twork, your print server will receive an IP address automatically. The IP address will then appear on the test page you printed earlier. If you are not working in a DHCP network, yo ...

  • Philips 5900 - page 17

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 17 Methods for Setting the IP Address You can set the IP address of your Axis Network Print Server using one of the following methods, dependin g on your network operating environment: * The IP address of the print server wi ll be set automatically using these methods. Notes: Regi ...

  • Philips 5900 - page 18

    Basic Installation (Wired & Wireless) 18 AXIS 5900 User’s Manual registered at a DDNS server, in the print ser ver’s Web interface. Refer to “Management and Configuration” on page 92. If the host name matches another en try in the DDNS data base, the Axis Network Print Server deletes th at entry before registering. Notes: Setting the IP ...

  • Philips 5900 - page 19

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 19 connected it to the ne twork. In the absence of a DHCP server, your Axis Network Print Server will automatically be assigned an IP address through integra ted Auto-IP. Th e Auto-IP address structure is: 169.254.xxx.xxx. The Auto-IP function will only work when DHCP is enabled i ...

  • Philips 5900 - page 20

    Basic Installation (Wired & Wireless) 20 AXIS 5900 User’s Manual 3. If the host returns Reply from 192.168.3.191 ... or a similar message, the IP address has been set successfully. Interrupt the “ping -t” loop by pressing CTRL+C on your keyboard. If the host returns Request timed out ... you need to perform a Factory Default on the print ...

  • Philips 5900 - page 21

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 21 1. Open a Terminal and write: 2. Without interrupting the “ping -t” loo p, restart the print server by disconnecting and then re-connecting the power supply. 3. If the host returns Reply from 192.168.3.191 ... or psname is alive ... or a similar message, the IP address has ...

  • Philips 5900 - page 22

    Basic Installation (Wired & Wireless) 22 AXIS 5900 User’s Manual 3. If it is not already running, start the RARP daemon. This is typically performed using the rarpd -a command. 4. Restart the AXIS 5900 to download the IP address. Using BOOTP in UNIX/Linux Below is an example of how to set the IP address of the Axis Network Print Server using ...

  • Philips 5900 - page 23

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 23 Configuring the Axis Network Print Server for Wireless Printing 1. Start your Web browser. 2. In the Location/Address field, type the host name or the IP address of your AXIS 5900 . 3. Click Admi n to enter the administrator’s pages. Note: 4. Create a certificate. See Enablin ...

  • Philips 5900 - page 24

    Basic Installation (Wired & Wireless) 24 AXIS 5900 User’s Manual 7. To access the WLAN settings page, click Admin | Network Settings | Detailed View | TC P/IP Network | WLAN WLAN Parameters Refer to the table below for a descri ption of the WLAN parameter settings used to configure the Axis Network Print Server for wireless printing. WLAN Par ...

  • Philips 5900 - page 25

    Basic Installation (Wired & Wirele ss) AXIS 5900 User’s Manual 25 Edit WEP Parameters Click the Edit WEP Parameters button. You will be prompted for the root password (default pass ). Enter the WEP keys and click OK to save your settings. Notes: When you have entered the WLAN sett ings to match your network, click OK to save your settings. Pr ...

  • Philips 5900 - page 26

    Basic Installation (Wired & Wireless) 26 AXIS 5900 User’s Manual Configuring your Print Server Configuration Methods Once you have set the IP address of your Axis Network Print Server print server, it can be managed and config ured over the LAN or WLAN using a number of different methods. The method that you choose should be dictated by your ...

  • Philips 5900 - page 27

    Adding Printers in Window s AXIS 5900 User’s Manual 27 Section 4 Adding Printers in Windows Overview of Installation Metho ds This section describes how to add ne twork printers to a computer in Windows. Refer to the table below to determine the most appropriate installation method according to your computer envir onment: If you intend to use the ...

  • Philips 5900 - page 28

    Adding Printers in Windows 28 AXIS 5900 User’s Manual client computer th at wants to print. Each client computer must install the appropriate printer drivers in order to print properly. SNMP Device Index When using the TCP/IP protocol (and if the printer driv er permits), the print server can use SNMP Statu s to find out if the printer is ready t ...

  • Philips 5900 - page 29

    Adding Printers in Window s AXIS 5900 User’s Manual 29 5. The Wizard searches for a suitable printer driver. If a suitable driver is not found, you w ill be asked to select a driver, otherwise the Wizard suggests which Printer Model and Printer Driver to use. Click Change driver to select another driver, or click Finish to accept and install the ...

  • Philips 5900 - page 30

    Adding Printers in Windows 30 AXIS 5900 User’s Manual Go Straight to the Print Server’s Web Interface Right-click on a printer in the Select Network Printer list an d select Print server ho me page to configure the print se rver from its embedded Web pages. Adding Printers in Windows 2000 / XP / 2003 using Windows Add Printer Wizard 1. Windows ...

  • Philips 5900 - page 31

    Adding Printers in Window s AXIS 5900 User’s Manual 31 3. Click the Create a new port radio button and select Standard TCP/IP Port from the list. Click Next and the Add Standard TCP/IP Printer Port Wizard starts. Click Next . 4. Enter the I P address of the print s erver in the Printe r Name or IP Addr ess field (Example: 192.168.3.191) The Port ...

  • Philips 5900 - page 32

    Adding Printers in Windows 32 AXIS 5900 User’s Manual 6. Select Manufacturer and Printer from the driver list or fro m a directory/file. Click Next . If you already have the printer’s dr iver installed, you will be asked whether to keep it or replace it. 7. Click Next . Supply a name for the printer and choose whether you want to make it your d ...

  • Philips 5900 - page 33

    Adding Printers in Window s AXIS 5900 User’s Manual 33 Adding Printers in Windows 2000 / XP / 2003 using the Microsoft LPR Monitor This section describes how to set up a Windows 2000/XP/2003 server for LPR printing over the TCP/IP protoc ol, using the built-in Microsoft LPR Monitor i.e. Print Services for UNIX. Note: Basic Setup If you have not a ...

  • Philips 5900 - page 34

    Adding Printers in Windows 34 AXIS 5900 User’s Manual Client/Server Printing Select Network printer instead of Local Printer in Step 2 above if your print server has already been insta lled by the administrator on another computer. Follow the in structions in the Add Printer Wizard to complete the installation. Important! Alternative Method for L ...

  • Philips 5900 - page 35

    Adding Printers in Window s AXIS 5900 User’s Manual 35 Installing a Network printer 1. Go to Start | Settings | Printers | Add Printer . Select My Compu ter and click Next . 2. From the Available Ports list, choose the appropriate printer port, which will appear as the IP address or host name of the print server. If it doesn’t appear in the lis ...

  • Philips 5900 - page 36

    Adding Printers in Windows 36 AXIS 5900 User’s Manual AXIS Print Monitor Software AXIS Print Monitor is the recommended tool to use for network printing in Windows 98 and Me environments. AXIS Print Monitor is available free of charge on www.axis.com AXIS Print Monitor Overview AXIS Print Monitor allows the print se rver to be connected in the sa ...

  • Philips 5900 - page 37

    Adding Printers in Window s AXIS 5900 User’s Manual 37 Adding Printers over TCP/IP in Wi ndows NT using AXIS Print Monitor 1. Install AXIS Print Monitor on all work stations that will print via the print server. AXIS Print Moni tor is availa ble free of charge on www.axis.com 2. To start the Add P rinter Wizard, select Settings | P rinters from t ...

  • Philips 5900 - page 38

    Adding Printers in Windows 38 AXIS 5900 User’s Manual Adding NetBIOS/NetBEUI Pr inters in Windows 2000 using AXIS Print Monitor See to it that the NetBEUI protocol is installed on your client. Follow the procedure below to install Axis Printer Ports from a Windows 2000 workstation: 1. To start the Add P rinter Wizard, select Settings | P rinters ...

  • Philips 5900 - page 39

    Adding Printers in Window s AXIS 5900 User’s Manual 39 Adding Printers over NetB IOS/NetBEUI in Windows NT using AXIS Print Monitor See to it that the NetBEUI protocol is installed on your client. Follow the procedure below to install Axis Printer Ports from a Windows NT workstation: 1. Install AXIS Print Monitor on all work stations that will pr ...

  • Philips 5900 - page 40

    Adding Printers in Windows 40 AXIS 5900 User’s Manual Adding Printers in Windows 98 and Me over TCP/IP using AXIS Print Monitor 1. Install AXIS Print Monitor on all work stations that will print via the Axis print server. 2. Next, start the Windows Ad d Printer Wizard: select Settings | Printers from the Start menu and double-click the Add Printe ...

  • Philips 5900 - page 41

    Adding Printers in Window s AXIS 5900 User’s Manual 41 Configure the Port: 1. Select Settings | Printers from the Start menu a nd highlight the printe r you wish to configure. Select File | Properties | Details and click Port Settings . 2. Choose whether error condition po p-up messages are to be displayed by checking the box in the Config ure AX ...

  • Philips 5900 - page 42

    Adding Printers in Macintosh 42 AXIS 5900 User’s Manual Section 5 Adding Printers in Macintosh Having connected the AXIS 5900 to your network, this section now describes how to set up your print se rv er for printing in Mac OS X and earlier Macintosh en viro nments using AppleTalk. If you intend to use the print server in a multi-protocol enviro ...

  • Philips 5900 - page 43

    Adding Printers in Macintosh AXIS 5900 User’s Manual 43 6. Click Add to finish the installation. The print server has now been added to the Printer List. 7. If you wish to configure printer settings, click Printers | Configure Pr inter . To Change the Bonjour Service Name You can change the print server’s Bonjou r service name via the print ser ...

  • Philips 5900 - page 44

    Adding Printers in Macintosh 44 AXIS 5900 User’s Manual Installation in Mac OS X using AppleTalk This section describes setting up your print server for printing in the Mac OS X. 1. Start Print Center (from Go | Applications | Utilities => P rint Center ) or the Printer Setup Utility . 2. Select Printers | Add Printer... 3. From the Printer Li ...

  • Philips 5900 - page 45

    Adding Printers in Macintosh AXIS 5900 User’s Manual 45 Installation on Mac OS 9.1 or older, using AppleTalk Basic Configuration On Mac OS 9.1 or older, basic configuration in AppleTalk is performed simply by opening the Chooser wi ndow and selecting a printer. You can change the default name of your print server or any of default parameters by e ...

  • Philips 5900 - page 46

    Adding Printers in Macintosh 46 AXIS 5900 User’s Manual 4. Click the name of the printer you want — t he ports are shown as <host name>_<port>. Example : AXIS100086_LPT1. 5. Click the Close box. This completes the configuration and closes the Chooser. Repeat this procedure for each Maci ntosh computer on the network using the print ...

  • Philips 5900 - page 47

    Adding Printers in Macintosh AXIS 5900 User’s Manual 47 BCP and TBCP You should specify if you want to en able or disable binary transfer of print data in the print server’s Web interface (Admin | Network Settin gs | Detailed View | Macintosh | Binary Protocol for Printer n . By enabling binary transfer you reduce printing time, provided that t ...

  • Philips 5900 - page 48

    Adding Printers in Macintosh 48 AXIS 5900 User’s Manual 6. Write a text file containing the parameters you want to set : Note: 7. Print the text file. The settings will be stored in the print server. 8. Open the Choose r and select the pr inte r port you wish to use for printing documents. 9. Close the Choo ser. Note: BINARY_TYPE_1. :BCP INT_ADDR ...

  • Philips 5900 - page 49

    Adding Printers in NetWare AXIS 5900 User’s Manual 49 Section 6 Adding Printers in NetWare This section describes how to contin ue the installation of the AXIS 5900 in the NetWare en vironment. Identify which transport protocol you are running on your network and which in stallation method you should use. Continue the installation by se lecting t ...

  • Philips 5900 - page 50

    Adding Printers in NetWare 50 AXIS 5900 User’s Manual Setup using NDPS The AXIS 5900 supports Novell Distribu ted Print Services (NDPS). You can run NDPS over Pure IP (TCP/IP) or IPX/SP X. Before the AXIS 5900 can be installed, make sure that NDPS is installed and a Broker is loaded on your NetWare file server. Axis Network Print Server uses the ...

  • Philips 5900 - page 51

    Adding Printers in NetWare AXIS 5900 User’s Manual 51 Public Access Printers Follow these instructions to create a publ ic access printer using the NDPS Manager object in your NetW are administrator utility: 1. Double-click on the NDPS Manager object you will be using to control the Printer A gents. 2. On the Identification page for the NDPS Mana ...

  • Philips 5900 - page 52

    Adding Printers in NetWare 52 AXIS 5900 User’s Manual 9. You will find the print server in the next window with the printer attached on the connected port. Depending on the tra nsport protocol you used when you start the installation, the print server should appear as following: • TCP/IP Network protocol: IP Address and Port , e.g: 192.168.70.2 ...

  • Philips 5900 - page 53

    Adding Printers in NetWare AXIS 5900 User’s Manual 53 The IPX Addresses for the above printers will appear as: <IPX External Network Number>:<Print server’s HW address>:<Socket Number> i.e.: 01d7e1c2:00408c5ff6a6:400c where 400c, 401c, and 402c are the so cket numbers corresponding to the LPT1 and LPT2 physical ports: If the p ...

  • Philips 5900 - page 54

    Adding Printers in NetWare 54 AXIS 5900 User’s Manual 5. Next, select the printer drivers for each client operating system. (Windows 2000, Windows NT and Windows 95/98). These drivers will be automatically downloaded to users’ workstations wh en they install this printer in the future. 6. Click Continue and OK in the next NDPS window. The new P ...

  • Philips 5900 - page 55

    Adding Printers in NetWare AXIS 5900 User’s Manual 55 4. From the Object menu, select Create . The New Object dialog appears. 5. Select NDPS Printer. The Create NDPS Printer dialog appears. 6. Type a name of your choi ce in the NDPS Printer Na me field, e.g. AXIS5FF66A_IPX 1 In the Printer Agent Source field, select the source of the Printer Agen ...

  • Philips 5900 - page 56

    Adding Printers in NetWare 56 AXIS 5900 User’s Manual 8. Confirm the Printer Agent name (default is the name of the new printer you are creating) and browse to select the NDPS Manager to which you want to assign it 9. Select AXIS Gateway Configuration in the Gateway Type field. 10. Click OK . 11. In the Select the printer’s type window choose y ...

  • Philips 5900 - page 57

    Adding Printers in NetWare AXIS 5900 User’s Manual 57 14. You will find the print server in th e next window with the printer attached on the connected port. Depending on the transport proto col you used when you start the installation, the print server will appear as: • TCP/IP Network protocol: IP Address and Port, e.g: 192.168.70.243 and LPT1 ...

  • Philips 5900 - page 58

    Adding Printers in NetWare 58 AXIS 5900 User’s Manual If the printer is not in the displayed print list: 1. Click Manually specify the prin t server enter the print server’s IP address in the IP Address field and choose a port in the Print server port field e.g., 192.168.70.243 and LPT1 (or LPT2 ) . IPX Network protocol: All the available ports ...

  • Philips 5900 - page 59

    Adding Printers in NetWare AXIS 5900 User’s Manual 59 If the printer is not in the displayed print list: 1. Click Ma nually specify the prin t server and enter the <IPX External Network Number> in the Network field. 2. Enter the <Print server’s HW address> in the LAN HW address field and choose a port in the Print server port field: ...

  • Philips 5900 - page 60

    Adding Printers in NetWare 60 AXIS 5900 User’s Manual 4. Next, select the printer drivers for each client operating system. (Windows 2000, Windows NT and Windows 95/98). These drivers will be automatically downloaded to users’ workstations wh en they install this printer in the future. 5. Click C ontinue and OK in the next NDPS window. Your pri ...

  • Philips 5900 - page 61

    Adding Printers in NetWare AXIS 5900 User’s Manual 61 Installing an NDPS Printer on a Workstation To install the printer on a workstatio n, use either Novell Printer Manager (NetWare 5.1 only) or the Add Printe r Wizard on th e local workstation. Using Novell Printer Manager 1. Log in as Admin. 2. On the any workstation, browse to <NW 5.1 File ...

  • Philips 5900 - page 62

    Adding Printers in NetWare 62 AXIS 5900 User’s Manual 5. The list of available printers shows the NDPS Public Access Printers on the network and the NDPS Controlled Acce ss Printers in you current NDS context. To see the Controlled Access Pr inters in other context that you have rights to, click the Browse button and select your choice. Click OK. ...

  • Philips 5900 - page 63

    Adding Printers in NetWare AXIS 5900 User’s Manual 63 7. Click OK . The default driver for that printer is then automatically downloaded. If the printer object does not have a printer driver associate d with it, or a driver was not found, you will be prompted to either to choose from a list of printer drivers provided by NDPS or to provide a disk ...

  • Philips 5900 - page 64

    Adding Printers in NetWare 64 AXIS 5900 User’s Manual 9. Verify by clicking Start - Settings - Printers on the workstation. Using the Add Printer Wizard 1. Click St art on your workstation, select Settings => Printers . There might be some differences regarding this menu depending of MS Operating System you are running. 2. Start the Add Printe ...

  • Philips 5900 - page 65

    Adding Printers in NetWare AXIS 5900 User’s Manual 65 5. Browse to the ND PS Printers . Expand either the NDPS Controlled Acce ss Printers or the NDPS Public Access Printers folder, select your newly installed NDPS printer and follow the instru ctions. When you have completed these steps, you are ready to start printing. Notes: • The Public Acc ...

  • Philips 5900 - page 66

    Adding Printers in NetWare 66 AXIS 5900 User’s Manual Setup using iPrint iPrint is Novell's next generation of printing software that lets users print to and from all destinations. A standard Web page displays available printers to the user. By clicking a printer, the iPrint c lient is installed (if not installed previously), the printer&apo ...

  • Philips 5900 - page 67

    Adding Printers in NetWare AXIS 5900 User’s Manual 67 4. Shutdown Tomcat and the NetWare Enterprise Web Server on the NetWare file server by executing the following commands: Type "NSWEBDN" <Enter> Type "TOMCAT33 -STOP" <Enter> Type "NVXADMDN" <Enter> 5. Map the next available dr ive (e.g. G:) to th ...

  • Philips 5900 - page 68

    Adding Printers in NetWare 68 AXIS 5900 User’s Manual 9. Click on Create Printer. 10. Choose a name of your choice for the printer 11. Choose the context where the printer will be installed. 12. Browse for the NDPS Manager and select it. 13. In the Gateway Type drop-down list, choose the Axis IPP Gateway Configuration . Press Next . 14. In the Pr ...

  • Philips 5900 - page 69

    Adding Printers in NetWare AXIS 5900 User’s Manual 69 Installing the iPrint Printer on the Workstation An iPrint printer can by locally instal led on the workstation in two ways: • Using the iPrint Client • Using the MS Add Printer Wizard at the workstation. See “Using the Add Printer Wizard” on page 64. Installing the iPrint Printer usin ...

  • Philips 5900 - page 70

    Adding Printers in NetWare 70 AXIS 5900 User’s Manual Basic Setup with AXIS NetPilot Install the AXIS NetPilot software on your computer. AXIS NetPilot runs on Windows 98 and Windows NT. Starting the Installation Follow the instructions below to install the AXIS 5900 with AXIS NetPilot: 1. Start AXIS NetPilot by double-clicking the NetPilot icon, ...

  • Philips 5900 - page 71

    Adding Printers in NetWare AXIS 5900 User’s Manual 71 AXIS 5900 Default Print Queue Names an d Prin t Server Port Names for each of the operating environments. Test Page The final user prompt in the Installation Wizard allows you to print a test page through NetWare. The test pa ge displays the name of all the NetWare servers the Axis Ne twork Pr ...

  • Philips 5900 - page 72

    Adding Printers in NetWare 72 AXIS 5900 User’s Manual 3. If you are not logged on to your Ne tWare file server, a dialog box will ask you to log on. The Axis Network Print Server peri odically updates the configuration by scanning the NDS tree or, in the ca se of NetWare versions 3.x, the designated file servers. Connecting Print Queues Follow th ...

  • Philips 5900 - page 73

    Adding Printers in NetWare AXIS 5900 User’s Manual 73 Notes: 10. If you want to define a remote pr inter number slot manually, check the Manual box and type the desired numb er in the box. 11. Click the OK button to return to the Net work Environments window. Basic Queue-based Printing over IP Axis print servers with software versio n 6.0 or late ...

  • Philips 5900 - page 74

    Adding Printers in NetWare 74 AXIS 5900 User’s Manual 4. Use the NetWare Administrator to create the printer, print server and queue objects in the NDS tree and then link them together. The Print Services Quick Setup (Non-NDPS) utility can be used for this. Go to To ols in the NetWare Administrator . 5. Use the Add Printer Wizard on your work sta ...

  • Philips 5900 - page 75

    Adding Printers in NetWare AXIS 5900 User’s Manual 75 Limitations • Lower performance, typically 20 - 70 kbytes/s for NLM and higher network load. Using Novell Utilities After installing the Axis Network Print Server into the NetWare environment, you can manage your Axis Network Prin t Server, using either Novell’s NetW are Ad ministrator, or ...

  • Philips 5900 - page 76

    Adding Printers in UNIX/Linux 76 AXIS 5900 User’s Manual Section 7 Adding Printers in UNIX/Linux Print Tools For printer configuration, printtool and printconfig are the most common. How they are invoked depends on which distribution and window manager you use. AIX SMIT is the recommended printing tool. It contains an integrated printer driver li ...

  • Philips 5900 - page 77

    Adding Printers in UNIX/Linux AXIS 5900 User’s Manual 77 Solaris 9 The printing tool is called Printer Administrator . This operating environment has an integrated printe r driver list, but does not have printer detection functionality. Instructions: Type the command /usr/sadm/admin/bin/printmgr in a Terminal window. SuSE YaST2 is the recommended ...

  • Philips 5900 - page 78

    Adding Printers in UNIX/Linux 78 AXIS 5900 User’s Manual Typical Invocation via a Windows Manager Using the Mandrake 8.2 distribution (with CUPS installed) and the KDE windows manger as an example, a t ypical set-up begins with starting Mandrake Control Center. 1. Click Hardwa re | Printer and the Printerdrake application will be invoked. 2. Clic ...

  • Philips 5900 - page 79

    Adding Printers in UNIX/Linux AXIS 5900 User’s Manual 79 Debian 3.0 Debian offers a choice between plain LPD, LPRng and CUPS. There are several printer configuration tools in this distribution, e.g. the apsfilter (version 5 or later), which adds support for LPRng and Ghostscript's uniprint driver scheme. Red Hat's printtool is also supp ...

  • Philips 5900 - page 80

    Adding Printers in UNIX/Linux 80 AXIS 5900 User’s Manual Red Hat 7.3 Printtool has been replaced by Printconf . The utility maintains the /etc/printcap configuration file, print spool directories, and print filters. Note: If you type printtool at a shell prompt, printconf will automatically start. Invocation 1. On the Gnome desktop, select the Ma ...

  • Philips 5900 - page 81

    Adding Printers in UNIX/Linux AXIS 5900 User’s Manual 81 Adding a Remote Unix Printer 1. To add a remo te UNIX printer, such as one attached to a d ifferent UNIX/Linux system on the same network, click the New button in the main printconf window. 2. Select Unix Printer from the Queue Type menu , and click Next . 3. Enter a unique name for the pri ...

  • Philips 5900 - page 82

    Adding Printers in UNIX/Linux 82 AXIS 5900 User’s Manual SuSE 8.0 The printing system on SuSE Linux is based on an apsfilter, with some enhancements; SuSE's apsfilter will recognize all common file formats (including HTML, if html2ps is installed). There are two ways to setup printers on SuSE systems: • YaST2 will let you configure "P ...

  • Philips 5900 - page 83

    Adding Printers in UNIX/Linux AXIS 5900 User’s Manual 83 AXIS axinstall Script Having performed the basi c TCP/IP setup procedures as defined earlier in this manual, you are now able to pr int in interactive mode using PROS, LPR, FTP or Reverse Telnet protocols. However, if you want to integrate the AXIS 5900 with your ho st spooler, you can use ...

  • Philips 5900 - page 84

    Adding Printers in UNIX/Linux 84 AXIS 5900 User’s Manual Print Methods on TCP/IP Networks The AXIS 5900 supports several differ ent print methods in the TCP/IP environment. axinstall will suggest a print method suitable for your particular UNIX/Linux system, but you might want to use another method depending on your printing requiremen ts (banner ...

  • Philips 5900 - page 85

    Adding Printers in UNIX/Linux AXIS 5900 User’s Manual 85 PROS A protocol developed at Ax is. Comes in two versions; named pipe (PROS A) and filter (PROS B). PROS A Advantages The AXIS 5900 appears as a device to th e system. This makes all filter and model options available. It provide s accounting and status logging. Supports bi-directional pr i ...

  • Philips 5900 - page 86

    Adding Printers in OS/2 86 AXIS 5900 User’s Manual Section 8 Adding Printers in OS/2 This section describes how to set up your print server for printing in the OS/2 environment. Continue wi th the instr uctions presented in the table below: TCP/IP Printing Having assigned an IP address to th e print server, you are now ready to install it for TCP ...

  • Philips 5900 - page 87

    Adding Printers in OS/2 AXIS 5900 User’s Manual 87 NetBIOS/NetBEUI Printing in OS/2 AXIS Print Utility for OS/2 is the tool to use for NetBIOS/NetBEUI printing in OS/2 environments. This tool can be fetched from www.axis.com => Software => Discontinued products. Instal l it if you have not already done so. If you want to change the de fault ...

  • Philips 5900 - page 88

    Adding Printers in OS/2 88 AXIS 5900 User’s Manual Creating a Print Queue (OS/2 version 2.x and OS/2 Warp) 1. Double-click the Templates folder, then drag the Printer icon out to the Workplace Shell (or into a folder) while holding the right mouse button down. 2. Type a name of your choice in the Name field. 3. Select PIPE<name>.LP1 (or L ...

  • Philips 5900 - page 89

    Updating the Firmware AXIS 5900 User’s Manual 89 Section 9 Updating the Firmware Upgrading the Firmware You can upgrade the AXIS 5900 firmware using one of the following methods: • AXIS ThinWizard (TCP/IP) • From the print server’s internal Web pages (TCP/IP) • FTP (TCP/IP) Note: Upgrading from the Print Server’s Internal Web Pages Foll ...

  • Philips 5900 - page 90

    Updating the Firmware 90 AXIS 5900 User’s Manual 7. If you do not have a default password, just click Next > . I f some of your servers use a different User ID or Passwo rd than the default entries, the y will be displayed in the Remainin g servers list. Enter the User ID and Password for each individual server. Click Next > . 8. Name the u ...

  • Philips 5900 - page 91

    Updating the Firmware AXIS 5900 User’s Manual 91 1. From www.axis.com, download the firmware and save it to a new directory on your computer, e.g. c:A xis (if the directory does not exist, create it). 2. Open a command prom pt from Start => Run . The Run window will appear. Type cmd and click OK . (Windows 98: Type command and click OK .) The ...

  • Philips 5900 - page 92

    Management and Con figuration 92 AXIS 5900 User’s Manual Section 10 Management and Configuration The management and configuration t ools that are supported by the Axis Network Print Server allow you to: • Change the print server parameters, i.e. editing the config file • Receive extended information about the print jobs • Receive printer po ...

  • Philips 5900 - page 93

    Management and C onfiguration AXIS 5900 User’s Manual 93 Admin When in Admin mode, you have access to all the print server's parameters and you can change them to your liking. This mode is intended for network administrators and can be password protected to prevent unauthorized changing of th e print server parameters. Note: Accessing the We ...

  • Philips 5900 - page 94

    Management and Con figuration 94 AXIS 5900 User’s Manual Available Services from the User Mode The following services are available from the User mode. A link to the Axis home page is available from this mode. Printer Overview The Printer Overview page contains a section that al lows you to view the general parameter setting of the Axis Network P ...

  • Philips 5900 - page 95

    Management and C onfiguration AXIS 5900 User’s Manual 95 accumulated usage of the connec ted pr inters allows you to control the usage of the connected printers. To delete an ongoing print job, use the delete button ne xt to the job. Network Settings From the Network Settings page you can set all parameters that control the network traffic to an ...

  • Philips 5900 - page 96

    Management and Con figuration 96 AXIS 5900 User’s Manual Software Default A Software Default will reset all prin t server parameters and settings to their default values except: • Node address (NODE_ADDR.) • IP Address (INT_ADDR.) • DHCP enabled (DHCP_ENB) • Installed certificate •P r i v a t e k e y Also see The Test Button , on page 1 ...

  • Philips 5900 - page 97

    Management and C onfiguration AXIS 5900 User’s Manual 97 Print Server Settings S o m e u s e f u l s et ti ng s t ha t c an be ch an ged in the print server are described here. See the print se rver’s Help pages for detailed information on all print server settings. For Changing the Network Printer’s ’Name’ From the print server’s Web i ...

  • Philips 5900 - page 98

    Management and Con figuration 98 AXIS 5900 User’s Manual Setting the e-mail Notification Parameters In order to set the e-mail addresse s of the people to whom the trouble- reports will be sent: 1. From your print server’s internal Web page, go to: Admin | Network Settings | Detailed View | e-mail No tification. The following options will appea ...

  • Philips 5900 - page 99

    Management and C onfiguration AXIS 5900 User’s Manual 99 Note: Wireless Printing Check-list Check the following before printing wirelessly. Click Admin | Network Settings | Detailed View | WLAN to check the print server settings. • The Network Mode parameter must be set to Auto Sense or WLAN. This parameter is set on the Ad min | General Settin ...

  • Philips 5900 - page 100

    Management and Con figuration 100 AXIS 5900 User’s Manual Network Print Server: • The character set can be changed to suit the printer • Strings can be added before and after the print data • Strings within the print data can be substituted • ASCII to PostScript conversion • Redirection of print data to another printer if the printer is ...

  • Philips 5900 - page 101

    Management and C onfiguration AXIS 5900 User’s Manual 101 You select your desired conver sion filter by setting the Character Set Conversion (PRx_CSET) parameter. The output from the conversion filter is always IBM PC Set 2 (Code Page 437) , and this is the character set the printer must be set up for. Example: Your network contains a host using ...

  • Philips 5900 - page 102

    Management and Con figuration 102 AXIS 5900 User’s Manual Follow the instructions below to add a string after the print job: 1. From the print server’s internal Web page, select Admin | Logical Printer Settings. 2. Select the Pri nter5 tab. 3. Enter th e string 04 in the String Af ter Print Job text field. 4. Click the OK button. Example: Follo ...

  • Philips 5900 - page 103

    Management and C onfiguration AXIS 5900 User’s Manual 103 4. Click the OK button. This is the default setting for logical printers PR5 through PR8. Example: Follow the instructions below to substitute command strings: 1. From the print server’s internal Web page, select Admin | Logical Printer Settings. 2. Select the Pri nter2 tab. 3. Enter th ...

  • Philips 5900 - page 104

    Management and Con figuration 104 AXIS 5900 User’s Manual Example: Follow the instructions below to conver t ASCII print data to PostScript for logical printer PR2: 1. From the print server’s internal Web page, select Admin | Logical Printer Settings. 2. Select the Pri nter2 tab. 3. Set the Printer Language Translation parameter to POSTSCR . 4. ...

  • Philips 5900 - page 105

    Management and C onfiguration AXIS 5900 User’s Manual 105 6. Enter the string 48 0 120 60 30 50 in the PostScript Page Format text field. 7. Enter th e string Helvetica in the PostScript Font text field. 8. Click the OK button. Redirecting Print Jobs when a Prin ter is Busy If print data is received for a printe r that is already busy, the host m ...

  • Philips 5900 - page 106

    Management and Con figuration 106 AXIS 5900 User’s Manual Read-back of Information The Axis Network Print Server suppor ts bi-directional printing. The information from the printer is read back on the parallel port when the parameter Read Back Port (PRx_ IN) has the default setting of AUTO. However, it is required that the printer also supports b ...

  • Philips 5900 - page 107

    Management and C onfiguration AXIS 5900 User’s Manual 107 Using AXIS ThinWizard fo r Print Server Management AXIS ThinWizard software allo ws you to manage and upgrade multiple Axis products. Using a standard We b browser, you can find, install, monitor, configure and upgrade your Axis print servers remotely in any TCP/IP network (WLAN or LAN). A ...

  • Philips 5900 - page 108

    Management and Con figuration 108 AXIS 5900 User’s Manual 5. The AXIS ThinWizard interface appears: Important! The first time you use AXIS ThinWizard, set the Preferences to reflect your network environment: Select a network group from the list on the Manage Network page. If the list is empty, you must firs t create a group. Click the Network Gro ...

  • Philips 5900 - page 109

    Management and C onfiguration AXIS 5900 User’s Manual 109 4. Click OK to create the network group. You can edit the properties of each network group from the Network Groups page. Simply sele ct the network group from the list and use one of the Edit , Copy or Remove commands. Managing Print Servers Follow the instructions below to ac cess the pri ...

  • Philips 5900 - page 110

    Management and Con figuration 110 AXIS 5900 User’s Manual Using FTP for Print Server Management Having assigned an IP address to your Axis Network Print Server, as described in “Assigning an IP Address to the Print Server” on page 16, you can change the Axis Network Prin t Server parameter settings using the File Transport Protocol (FTP). Ens ...

  • Philips 5900 - page 111

    Management and C onfiguration AXIS 5900 User’s Manual 111 Example: Viewing the Status File The status command shows which prin ter port the logical printers are assigned to, and their curren t status. Follow the instructions below to view the status file using FTP: 1. Log in to the Axis Network Print Server by typing: ftp <host name> or ftp ...

  • Philips 5900 - page 112

    Management and Con figuration 112 AXIS 5900 User’s Manual 1. Log in to the Axis Network Print Server by typing: ftp <host name> or ftp <IP address> in a DOS wi ndows (W indows and OS/2) or in a UNIX shell window . 2. Enter the user id and the password. (The default entries are root and pass .) 3. Download the account file t o your hos ...

  • Philips 5900 - page 113

    Management and C onfiguration AXIS 5900 User’s Manual 113 Example: Typical Telnet session to v iew the Account File Viewing the Status file The status command shows which prin ter port the logical printers are assigned to, and their curren t status. Follow the instructions below to view the status file using telnet: 1. Log in to the Axis Network ...

  • Philips 5900 - page 114

    Management and Con figuration 114 AXIS 5900 User’s Manual 3. Restart the print server’s protocols by typing: softreset Replace the command in step 3 above with hardreset or default to perform the other two reset operations. Telnet Help By typing help in step 3 in any of the Telnet instruction sets above, a list of all available commands will be ...

  • Philips 5900 - page 115

    Management and C onfiguration AXIS 5900 User’s Manual 115 The AXIS MIB The AXIS MIB contains a large nu mber of objects which may be categorized as follows: • Menu objects - used for viewing an d changing the Axis Network Print Server configuration from the NMS program. Refer to The Parameter List , on page 142. • Printer status and unit admi ...

  • Philips 5900 - page 116

    Management and Con figuration 116 AXIS 5900 User’s Manual Generating a Self- Signed Certificate 1. Select the Generate Self-Signed Certificate radio button and click Next . 2. Enter th e data asked fo r: • Country Name: Example : US • State or Province Name: Example : California • Locality Name: Example : Los Angeles •O r g a n i z a t i ...

  • Philips 5900 - page 117

    Management and C onfiguration AXIS 5900 User’s Manual 117 Accessing the Print Server’s Web Pages over https:// Whenever SSL/TLS is enabled, you can only reach the print server’s Web interface through the secure servic es. The unsecur e way via http:// is closed and now you have to address the print server’s Web interface in the secure way, ...

  • Philips 5900 - page 118

    Management and Con figuration 118 AXIS 5900 User’s Manual Enabling the SNMPv3 Protocol Invoke the print server’s Web interf ace to enable the SNMPv3 protocol. 1. Select Admin | Network Settings | Detailed View | TCP/IP Network and ensure that HTTPS Enabled is set to yes to guarantee a secure configuration. Note: You must have a valid certificat ...

  • Philips 5900 - page 119

    Management and C onfiguration AXIS 5900 User’s Manual 119 Using Novell Utilities for Print Server Management After installing the Axis Network Print Server into the NetWare environment, you can manage your Axis Network Prin t Server, using either Novell’s NetWare Administrator , or PCONSOLE (Not available in NetWare version 5.x or higher). NetW ...

  • Philips 5900 - page 120

    Management and Con figuration 120 AXIS 5900 User’s Manual Print Layout You can view installed Axis Network Print Server Network Print Servers and their relative print queues for any NetWare Organizational Unit. You can also display summary information by right-clicking on the printer object you want to examine. NetWare Print Layout with cor respo ...

  • Philips 5900 - page 121

    Management and C onfiguration AXIS 5900 User’s Manual 121 NetWare Packet Signature Levels NetWare Packet Signatures protect servers and clients using the NCP (NetWare Core Protocol) services and prevent packet forgery by requiring the server and the clien t to sign each NCP packet. There are two levels of NCP Packet Signature: the Server Level an ...

  • Philips 5900 - page 122

    Management and Con figuration 122 AXIS 5900 User’s Manual TCP/IP Restrictions In a new and unconfigured Axis Networ k Print Server any user is allowed to send TCP/IP print jobs. Using a re striction list you can reject TCP/IP printing from specified IP addresses. Enabling TCP/IP Restrictions In the print server’s Web interface, select Admin | N ...

  • Philips 5900 - page 123

    IPP - Internet Printing Protocol AXIS 5900 User’s Manual 123 Section 11 IPP - Internet Printing Protocol The Axis Network Print Server enables printing ove r the Interne t with IPP (Internet Printing Protocol), an indu stry standard that allows users to print to remote printers across the Internet. With IPP, a user with an Internet connection can ...

  • Philips 5900 - page 124

    IPP - Intern et Printing Prot ocol 124 AXIS 5900 User’s Manual Address Schemes for IPP Printers When using IPP printing, you need to know the IP addres s or host name of your Axis print server. IPP is a client/server type protocol which comprises two industry standards: • the 1.0 standard, which uses an http:// address scheme • the 1.1 standa ...

  • Philips 5900 - page 125

    IPP - Internet Printing Protocol AXIS 5900 User’s Manual 125 Adding an IPP Printer to your Printer List in Windows 98 1. Install the IPP client for Windows 98 on your computer. This IPP client can be downloaded from the Microsoft Web site. 2. Open Start | Settings | Printers. 3. Choose Add Printer , then Network Printer . 4. In the Printer field ...

  • Philips 5900 - page 126

    IPP - Intern et Printing Prot ocol 126 AXIS 5900 User’s Manual 5. In the Available Por ts window, click Add Port : 6. The Printer Ports dialog will appear, showing a list of Available Printer Ports . 7. Choose The HP Internet Prin ter Connection Port and click New Port. 8. The HP Internet Printer Connection will start. Click Next . ...

  • Philips 5900 - page 127

    IPP - Internet Printing Protocol AXIS 5900 User’s Manual 127 9. In the IP Address, Host Name or URL field, type the address of the Axis Network Print Server to which the destination printer is connect ed. The URL will automatically appear in the Port Name field as well: ( Example: http://171.16.5.218:63 1/LPT1 or LPT2 ). Click Next . 10. The Wiza ...

  • Philips 5900 - page 128

    IPP - Intern et Printing Prot ocol 128 AXIS 5900 User’s Manual 14. The new printer will appear in your Printer window. You are now ready to start printing using IPP. How to Print from Windows 2000/XP/2003 Before you print to an IPP printer you will need to know: • the address of the print server. The address contains the IP address or host name ...

  • Philips 5900 - page 129

    IPP - Internet Printing Protocol AXIS 5900 User’s Manual 129 4. Enter the printer ad dres s in the URL field. ( Example: http://171.16.5.218:63 1/LPT1 or LPT2 ) Click Next . 5. If you do not have a driver corresponding to the destination printer installed on your computer, the Wizard will prompt you to install one. Click OK . 6. The Installation ...

  • Philips 5900 - page 130

    IP Addressing 130 AXIS 5900 User’s Manual Section 12 IP Addressing IP Address and Subnet Mask The print server must be correctly configur ed with the following information to function properly: • an IP address •a s u b n e t m a s k • a default gateway (or router) IP Address Each device on your network must ha ve a unique IP address to oper ...

  • Philips 5900 - page 131

    IP Addressing AXIS 5900 User’s Manual 131 Type Two In larger (Class B) ne tworks, where ther e are more devices, th e IP address of ‘162.168.3.191’ is split into two parts but is structured differently: • Part one (‘162.168’) identifies the ne twork on which the device resides. • Part two (‘.3.191’) identifies the device within th ...

  • Philips 5900 - page 132

    IP Addressing 132 AXIS 5900 User’s Manual Auto-IP Addressing Network devices use automatic IP addressing if they are configured to acquire an address using DHCP but ar e unable to contact a DHCP server. Automatic IP addressing is a scheme wh ere devices allocate themselves an IP address at random from the indu stry standard subnet of 169.254.x.x ...

  • Philips 5900 - page 133

    IP Addressing AXIS 5900 User’s Manual 133 Setting the IP Address using DHCP Follow the instructions below to dow nload the IP address using DHCP: 1. Edit or create a scope in the DHCP manager of the DHCP daemon. The entries included in this scope should contain the following parameters: • range of IP addresses • subnet mask • default router ...

  • Philips 5900 - page 134

    The Test Button 134 AXIS 5900 User’s Manual Section 13 The Test Button The test button is located on the fr ont right hand side of the AXIS 5900 and is used for: • Printing a test page to check the connection to the printer. • Printing a parameter list to see th e print server’s current settings. • Performing a Factory Default of the prin ...

  • Philips 5900 - page 135

    Troubleshooting AXIS 5900 User’s Manual 135 Section 14 Troubleshooting This section provides useful informatio n to help you resolve difficulties you might have with your AXIS 5900. Fault symptoms, possible causes and remedial actions are provided within a qu ick reference table. Please visit the Axis W eb site for la test troubleshooting tips, m ...

  • Philips 5900 - page 136

    Troubleshooting 136 AXIS 5900 User’s Manual IP Address Check with Ping By sending a data packet to a specific IP address and waiting for a reply, Ping can determine whethe r that IP address is accessible. Ping can also help you to determine IP address conflicts with your AXIS 5900 and troubleshoot TCP/IP problems on th e network. Follow the instr ...

  • Philips 5900 - page 137

    Troubleshooting AXIS 5900 User’s Manual 137 Axis Support Server Report In order to obtain optimal support from Axis support technicians, please follow these instructions when filling in and submitting a Support question. 1. Go to the print server’s Web pages by t yping the print server’s IP address in the Address/Location field of your Web br ...

  • Philips 5900 - page 138

    Technical Specifications 138 AXIS 5900 User’s Manual Section 15 Technical Specifications Supported Printers All parallel printers exce pt host-based printers and copiers, e.g. CAPT, GDI, PPA Supported Systems Microsoft Windows 95, 98, Me, NT, 2000, XP and 2003 Novell NetWare 3.X, 4.X, 5.X, 6.X. Supports bi ndery and NDS mode. Supports user messag ...

  • Philips 5900 - page 139

    Technical Specifications AXIS 5900 User’s Manual 139 Logical Printers Lo gical printer ports can be progr ammed to perform auto ASCII to PostScript conversion, add string before and after job, string substitution, alternative output and character set conversion RF Specifications Unlicenced 2.4 GHz frequency band, RX sensitivity - 70 dBm, TX power ...

  • Philips 5900 - page 140

    Technical Specifications 140 AXIS 5900 User’s Manual Network Connection Supports: IEEE802.2, IEEE802.3, SNAP and Ethernet II frame types simultaneously NWay for autodetection of network speed WLAN SNAP/802.2/802.3 for 802.11b Ethernet All standard Ethernet and Fast Et hern et networks: RJ-45 connector (Category 5 or 6, shielded twisted pair cable ...

  • Philips 5900 - page 141

    Technical Specifications AXIS 5900 User’s Manual 141 Approvals EMC EN 55 022:1998 (CISPR 22:1 997), Class B EN 55 024:1998 EN61000-3-2:19 95+A1+A2+Corrig.+A1 4 EN 61000-3-3:1 995+A1 ETS 300 826 FCC 47 CFR part 15 Other ETS 300 32 8 ARIB T-66 Safety EN 60950:2000, approved power su pplies for all countries Included Accessories AXIS Network Product ...

  • Philips 5900 - page 142

    The Parameter List 142 AXIS 5900 User’s Manual Section 16 The Parameter List These are the defau lt parameters in a ne w, unconfigured print server . A complete list of all Axis prin t server parameters can be found on www.axis.com AXIS 5900 (AXIS 5900 Network Print Server V7.00 Oct 01 2004. S /N: 00408C5E44D6) Parameter settings: --- General Men ...

  • Philips 5900 - page 143

    The Parameter List AXIS 5900 User’s Manual 143 TCP_ENB. : YES PAR_TCP_RESTRICT_LIST. : PROS_PWD. : netprinter PROS_PRT. : 35 LPD_BANN. : OFF (OFF, AUTO, LAS T) DEFAULT_RAW_TCP. : 9100-9101 (9100 -9101, CLOSED) RTN_OPT. : NO RTEL_PR1. : 0 RTEL_PR2. : 0 RTEL_PR3. : 0 RTEL_PR4. : 0 RTEL_PR5. : 0 RTEL_PR6. : 0 RTEL_PR7. : 0 RTEL_PR8. : 0 --- SNMP Men ...

  • Philips 5900 - page 144

    The Parameter List 144 AXIS 5900 User’s Manual NPRINTER6. : NPRINTER7. : NPRINTER8. : --- NetBIOS/NetBEUI Menu LSLM_ENB. : YES NB_FR_TYPE. : FR_802_2 (FR_AUTO, FR_802_2, FR_DIX) LPRINT_1. : AX5E44D6.LP1 LLOGIC_1. : PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8, LPT1, LPT2) LPRINT_2. : AX5E44D6.LP2 LLOGIC_2. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, ...

  • Philips 5900 - page 145

    The Parameter List AXIS 5900 User’s Manual 145 --- Printer2 Menu PR2_OUT. : LPT2 (NONE, LPT1, L PT2) PR2_NAME. : PR2_SCND. : PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR2_WAIT. : YES PR2_IN. : AUTO (AUTO, NONE) PR2_BEF. : PR2_STR. : PR2_CSET. : NONE (NONE, ISO>IBM, 7UK>IB M, 7SW>IBM, 7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM) PR2 ...

  • Philips 5900 - page 146

    The Parameter List 146 AXIS 5900 User’s Manual PR5_DUMP. : NO PR5_SIZE. : A4 (A4, LETTER, LEG AL, EXECUT) PR5_ORNT. : PORTR (PORTR, LANDS , R_PORTR, R_LANDS) PR5_FORM. : 66 0 100 60 30 50 PR5_FONT. : --- Printer6 Menu PR6_OUT. : LPT2 (NONE, LPT1, L PT2) PR6_NAME. : PR6_SCND. : PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7, PR8) PR6_WAIT. : YES PR6_IN. : ...

  • Philips 5900 - page 147

    The Parameter List AXIS 5900 User’s Manual 147 --- LPT2 Menu L2_CENTR. : HISPEED (IBM_PC, STNDRD, FAST, HISPEED, HINOACK) L2_BSYTM. : 60 L2_MGM_INFO. : AUTO (DISABLE, AUTO ) L2_COMMENT. : L2_BIDIR. : AUTO (DISABLE, AUTO ) L2_READT. : 3 --- Email Menu EMAIL_NOTIFICATION. : NO REPLY_ADDRESS. : PAPER_JAM_ADDRESS. : OUT_OF_PAPER_ADDRESS. : TONER_LOW_ ...

  • Philips 5900 - page 148

    The Parameter List 148 AXIS 5900 User’s Manual Enable SNMP Status SNMP Status is enabled thr oug h Windows’ printer port settings. Example You have a three port print server an d want to enable SNMP Status for LPT2. The table above tells you to set the SNMP Device Index to 3. Using Windows XP as an example: 1. Go to Start | Printers and Faxes . ...

  • Philips 5900 - page 149

    Glossary AXIS 5900 User’s Manual 149 Section 17 Glossary 802.11b A standard for wireless LAN communi cations operating within the 2.4 GHz ISM band. Access Point A network attached device that acts as a bridge between th e wireless LAN and the wired LAN and inte rconnects wireless clients. AIX Advanced Interactive eXe cutive. A vers ion of the UNI ...

  • Philips 5900 - page 150

    Glossary 150 AXIS 5900 User’s Manual config File This is a file that reside s in the pr int server’s memory and contains all the parameters that determine the print se rver’s functionality. By editing the config file (changing the parameter setti ngs), you can configure the print server to meet the printing ne eds of your network. Client/serv ...

  • Philips 5900 - page 151

    Glossary AXIS 5900 User’s Manual 151 IPP Internet Printing Protocol. A developi ng industry standard that allows users to print to remote printers across the I nternet. With IPP, a user with an Internet connection can send a document to any printer connected to the Internet. IPP is platform independent and can be used to print over any LAN or WAN ...

  • Philips 5900 - page 152

    Glossary 152 AXIS 5900 User’s Manual NetWare An operating system for local area networks. PCL Printer Control Language — a set of command codes used when printing. A PCL driver is a small program that works between the operating system and the printer. Peer-to-Peer Printing When selecting Peer-to-peer printing, all print jobs are sent directly ...

  • Philips 5900 - page 153

    Glossary AXIS 5900 User’s Manual 153 TFTP Trivial File Transfer Protocol (TFTP) is an Internet software utility for transferring files that is simpler to use than the File Transfer Protocol (FTP) but less capable. It is used wh ere user authentication and directory visibility are not required. TFTP uses the User Datagram Protocol (UDP) rather tha ...

  • Philips 5900 - page 154

    Index 154 AXIS 5900 User’s Manual Index Numerics 802.11b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 A Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Account file . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 155

    Index AXIS 5900 User’s Manual 155 C CA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Certificate Authority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 156

    Index 156 AXIS 5900 User’s Manual Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Flash Loading over the Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 157

    Index AXIS 5900 User’s Manual 157 LLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Local Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 33 Logical Link Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 158

    Index 158 AXIS 5900 User’s Manual P Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 PCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Peer-to-Peer Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 159

    Index AXIS 5900 User’s Manual 159 Software Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 SPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 SSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Philips 5900 - page 160

    Index 160 AXIS 5900 User’s Manual Windows Adding Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 WINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 18, 153 Host Name Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Manufacturer Philips Category Printer

Documents that we receive from a manufacturer of a Philips 5900 can be divided into several groups. They are, among others:
- Philips technical drawings
- 5900 manuals
- Philips product data sheets
- information booklets
- or energy labels Philips 5900
All of them are important, but the most important information from the point of view of use of the device are in the user manual Philips 5900.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Philips 5900, service manual, brief instructions and user manuals Philips 5900. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Philips 5900.

Similar manuals

A complete manual for the device Philips 5900, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Philips 5900 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Philips 5900.

A complete Philips manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Philips 5900 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Philips 5900, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Philips 5900, that we can find in the current document
3. Tips how to use the basic functions of the device Philips 5900 - which should help us in our first steps of using Philips 5900
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Philips 5900
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Philips 5900 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Philips 5900?

Use the form below

If you did not solve your problem by using a manual Philips 5900, ask a question using the form below. If a user had a similar problem with Philips 5900 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)