English dropdown-ico

Manual Texas Instruments BQ24351EVM

13 pages 0.33 mb
Download

Go to site of 13

Summary
  • Texas Instruments BQ24351EVM - page 1

    User's Guide SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC This user's guide describes the features, setup, and operation of the bq24351EVM evaluation module. Included are the bill of materials, board layout, and schematic. Contents 1 Introduction ........................................................... ...

  • Texas Instruments BQ24351EVM - page 2

    Introduction www.ti.com 1 Introduction 1.1 General Description The bq24351 evaluation module (EVM) is a complete charger module for evaluating a charger front-end protection and charger solution using the bq24351 and bq2057C devices. It is designed to deliver up to 560 mA of charge current to Li-ion or Li-polymer applications. The charger front-end ...

  • Texas Instruments BQ24351EVM - page 3

    www.ti.com Test Summary 1.4 Controls and Key Parameters Setting Jack (1) Description Factory Setting JP1 If on, high-side sensing resistor is disabled Jumper on JP2 Reserved for other ICs Jumper (BATEN, GND) on JP3 bq24351 GATDRV pin Jumper off JP4 bq2057C BAT pin connection to bq24351 Jumper on JP5 bq2057C VCC pin connection to bq24351 Jumper on J ...

  • Texas Instruments BQ24351EVM - page 4

    F AUL T VBA T GA TDR V CHGIN BA T EN OUT BA T + GND HP A666 bq24351EVM JP7 V Supply 1 J1 DC+ JP1 U1 J4 BA T + V I 2 Ibat CFET AP PLICA TIO N CIRCUIT JP6 JP5 JP 4 JP3 JP 2 U2 J2 J3 I I Load 1 Test Summary www.ti.com 2.2.2 Load 1 A 10-V (or above), 2-A (or above) electronic load that can operate in constant-current mode. 2.2.3 Load 2 A 10-V (or above ...

  • Texas Instruments BQ24351EVM - page 5

    www.ti.com PCB Layout Guideline 2.4 Procedure 2.4.1 Charger Current and Voltage Regulation 1. Ensure that steps in Section 2.3 are followed. 2. Enable output of PS 1. 3. Increase the output voltage of PS 1 to 5 V ± 0.1 V. 4. Enable the output of load 2. Measure → V(J2(OUT)) = 3.6 V ± 200 mV Measure → Ibat = 560 mA ± 70 mA Observe → D2 on, ...

  • Texas Instruments BQ24351EVM - page 6

    Bill of Materials, Board Layout, and Schematic www.ti.com 4 Bill of Materials, Board Layout, and Schematic 4.1 Bill of Materials Table 1. Bill of Materials bq24351 RefDes Value Description Size Part Number MFR 1 C1 1 µ F Capacitor, ceramic, 35-V, X5R, 10% 603 Std Std 3 C2, C3, C5 1 µF Capacitor, ceramic, 10-V, X7R, 10% 603 Std Std 1 C4 0.1 µF Ca ...

  • Texas Instruments BQ24351EVM - page 7

    C001 www.ti.com Bill of Materials, Board Layout, and Schematic 4.2 Board Layout Figure 2. Top Layer 7 SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated ...

  • Texas Instruments BQ24351EVM - page 8

    C002 Bill of Materials, Board Layout, and Schematic www.ti.com Figure 3. Bottom Layer 8 bq24351EVM for Li-Ion Charger Front-End Protection IC SLUU455 – October 2010 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated ...

  • Texas Instruments BQ24351EVM - page 9

    C003 www.ti.com Bill of Materials, Board Layout, and Schematic Figure 4. Top Silk Screen 9 SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated ...

  • Texas Instruments BQ24351EVM - page 10

    C004 Bill of Materials, Board Layout, and Schematic www.ti.com Figure 5. Top Assembly 10 bq24351EVM for Li-Ion Charger Front-End Protection IC SLUU455 – October 2010 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated ...

  • Texas Instruments BQ24351EVM - page 11

    CAUTION: Device may have surface temperature in excess of 60°C when unit is operational. www.ti.com Bill of Materials, Board Layout, and Schematic 4.3 Schematic Figure 6. bq24351 Schematic 11 SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporate ...

  • Texas Instruments BQ24351EVM - page 12

    Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling th ...

  • Texas Instruments BQ24351EVM - page 13

    IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders ...

Manufacturer Texas Instruments Category Battery Charger

Documents that we receive from a manufacturer of a Texas Instruments BQ24351EVM can be divided into several groups. They are, among others:
- Texas Instruments technical drawings
- BQ24351EVM manuals
- Texas Instruments product data sheets
- information booklets
- or energy labels Texas Instruments BQ24351EVM
All of them are important, but the most important information from the point of view of use of the device are in the user manual Texas Instruments BQ24351EVM.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Texas Instruments BQ24351EVM, service manual, brief instructions and user manuals Texas Instruments BQ24351EVM. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Texas Instruments BQ24351EVM.

Similar manuals

A complete manual for the device Texas Instruments BQ24351EVM, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Texas Instruments BQ24351EVM by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Texas Instruments BQ24351EVM.

A complete Texas Instruments manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Texas Instruments BQ24351EVM - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Texas Instruments BQ24351EVM, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Texas Instruments BQ24351EVM, that we can find in the current document
3. Tips how to use the basic functions of the device Texas Instruments BQ24351EVM - which should help us in our first steps of using Texas Instruments BQ24351EVM
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Texas Instruments BQ24351EVM
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Texas Instruments BQ24351EVM in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Texas Instruments BQ24351EVM?

Use the form below

If you did not solve your problem by using a manual Texas Instruments BQ24351EVM, ask a question using the form below. If a user had a similar problem with Texas Instruments BQ24351EVM it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)