English dropdown-ico

Manual Kenwood AT-130

12 pages 1.41 mb
Download

Go to site of 12

Summary
  • Kenwood AT-130 - page 1

    ...

  • Kenwood AT-130 - page 2

    The Model AT-130 is designed to satisfy your antenna-tuning requirements. It has been manu- factured with the quality and performance that makes Kenwood "The Pacesetter in Amateur Radio". This unit has been carefully engineered and manu- factured under rigid quality standards, and should give you satisfactory and dependable operation for ...

  • Kenwood AT-130 - page 3

    (,,PIL-~) ww 691 -a (1,9) wwz91 'M (,,8/&-Z) ww09 'H pnls pue lnu 6u!~ (~04 )adAl dHfl (U09)adAljHfl .y3$ew wnw!ldo le gp 5.0 ueyl ssa1 (M OZ 1 'Pueq ZH W 4'&) 'Xew M 0s 1 'pa3uelequn ' uoo& 01 02 004 ZH W L'6Z 01 S'E wo~~ spueq ~na~ewe.8 ...

  • Kenwood AT-130 - page 4

    Accessories: Carefully unpack your AT-1 30 Antenna Tuner and verify the following accessories are included. * Operating manual . . . . . . . . . 1 copy * Mounting bracket (J29-0402-02) . . 1 piece * Mounting hardware Screw, 4 mm diameter . . . . . . . 4 pieces Flat washer, 4 mm diameter . . . 4 pieces Lock washer, 4 mm diameter . . 4 pieces Nut, 4 ...

  • Kenwood AT-130 - page 5

    JIIIII~~IIIII~~~~~~I~~IIIII~~IIIII~~IIII~~~IIIII~~IIIII~~IIIII~~IIIII~~IIIII~~IIIII~~IIII~~~IIIII*~IIIII~IIIIII~~IIIII-~IIII~~~IIIII~~IIIII~~IIII~~~IIIII~~I~III~~IIIII*~IIIII~~IIIII~~IIIII*~IIII~~~IIII~~~IIII~ - - - - - ! - - SECTION 2. CONTROLS AND THEIR FUNCTIONS I - - ~~~~~~~~~~~~~~~~~~~I~-~IIII~.~IIII~~~IIII~.~~III~.~IIII~~~IIII~.~IIII~.~IIII~. ...

  • Kenwood AT-130 - page 6

    Measuring antenna system SWR (i) Using an all solid-state transceiver (such as a TS-130s or TS-130V) Before setting up the antenna coupler, first determine the antenna system SWR. a. Set the controls as shown in Figure3-2. Set the BAND switch to the "THROUGH" position. b. In the transmit mode, calibrate the meter with the calibration cont ...

  • Kenwood AT-130 - page 7

    Adjusting the Antenna Coupler The antenna coupler is used to match a trans- mitter to an antenna system when its SWR is too high (i.e., greater than 1.5:1 SWR). a. Place the BAND switch to the same band setting as your transceiver (as shown in Figure 3-41, b. Set the CALISWR switch to the CAL (I) position. c. Transmit and adjust the CAL control so ...

  • Kenwood AT-130 - page 8

    AT-130 Mobile Installation . Securely install the Mobile Mount using four lock washers, four flat washers, and four screws and nuts. Install the AT-130 in the Mobile Mount by four wing bolts and polyethylene washers. Adjust the tilt before tightening the bolts. Mounting bracket Figure 3-5. Mounting bracket Detail Figure 3-6. Adjusting the Mounting ...

  • Kenwood AT-130 - page 9

    Figure 11 shows a block diagram of the AT-1 30. Direcltional Coupler The directional coupler samples forward and reflected power from the transceiver to the load. Meter Circuit The forward and reflected power sampled by the directional coupler is used for SWR measure- ment. Forward power is calibrated with the CAL control so reflected power is read ...

  • Kenwood AT-130 - page 10

    1. General lnformation Your AT-130 has been factory aligned and tested include a photocopy of the bill of sale, or other proof of purchase showing the to specification before shipment. Under normal date of sale. circumstances, it wili operate in accordance with these operating instructions. If your unit fails to work, contact the authorized dealer ...

  • Kenwood AT-130 - page 11

    Circuits and specifications are subject to change for improvement. [g cT ~ SWR LAMP 12V ...

  • Kenwood AT-130 - page 12

    Model : AT-1 30 ......................................................................................................... Serial ........................... Date Purchased ..................................................... ........................................................................................................ Dealer A product of ...

Manufacturer Kenwood Category Car Stereo System

Documents that we receive from a manufacturer of a Kenwood AT-130 can be divided into several groups. They are, among others:
- Kenwood technical drawings
- AT-130 manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood AT-130
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood AT-130.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood AT-130, service manual, brief instructions and user manuals Kenwood AT-130. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood AT-130.

Similar manuals

A complete manual for the device Kenwood AT-130, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood AT-130 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood AT-130.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood AT-130 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood AT-130, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood AT-130, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood AT-130 - which should help us in our first steps of using Kenwood AT-130
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood AT-130
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood AT-130 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood AT-130?

Use the form below

If you did not solve your problem by using a manual Kenwood AT-130, ask a question using the form below. If a user had a similar problem with Kenwood AT-130 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)