Manual Mitsubishi 6G7

55 pages 1.1 mb
Download

Go to site of 55

Summary
  • Mitsubishi 6G7 - page 1

    GENERAL INFORMA TION 1 1A-0-3 ........................................... 1. SPECIFICA TIONS 1 1A-1-1 ............................................... SERVICE SPECIFICA TIONS 1 1A-1-1 .................................. REWORK DIMENSIONS 1 1A-1-2 ....................................... T ORQUE SPECIFICA TIONS 1 1A-1-3 ................................ ...

  • Mitsubishi 6G7 - page 2

    1 1A-0-2 PWEE9615 E Dec. 1996 Mitsubishi Motors Corporation NOTES ...

  • Mitsubishi 6G7 - page 3

    6G7 ENGINE (E - W) - General Information 1 1A-0-3 GENERAL INFORMA TION GENERAL SPECIFICA TIONS Descriptions 6G72-SOHC T ype 60 _ OHV , SOHC Number of cylinders 6 Combustion chamber Compact type T otal displacement dm 3 2.972 Cylinder bore mm 91.1 Piston stroke mm 76.0 Compression ratio 8.9 V alve timing Intake valve Opens (BTDC) 15 ° (Camshaft ide ...

  • Mitsubishi 6G7 - page 4

    6G7 ENGINE (E - W) - Specifications 1 1A-1-1 1. SPECIFICA TIONS SERVICE SPECIFICA TIONS Items Standard Limit Timing belt Auto-tensioner rod length mm 3.8 - 5.0 - Auto-tensioner rod projection length mm 12 - Auto-tensioner rod pushed-in amount (when pushed with a force of 98 - 196 N) mm 1.0 or less - Rocker arms and camshaft Camshaft cam height mm ( ...

  • Mitsubishi 6G7 - page 5

    6G7 ENGINE (E - W) - Specifications 1 1A-1-2 Items Limit Standard Oil pump side clearance mm 0.04 - 0.10 - Oil pump body clearance mm 0.10 - 0.18 0.35 Piston and connecting rod Piston outside diameter mm 91.1 - Piston ring to ring groove clearance mm No. 1 0.03 - 0.07 0.1 No. 2 0.02 - 0.06 0.1 Piston ring end g ap mm No. 1 0.30 - 0.45 0.8 No. 2 0.4 ...

  • Mitsubishi 6G7 - page 6

    6G7 ENGINE (E - W) - Specifications 1 1A-1-3 TORQUE SPECIFICA TIONS Items Nm Alternator Drive belt tensioner pulley nut 49 Crankshaft bolt 181 Alternator pivot nut 44 Alternator bolt M8 21 Alternator bolt M10 48 Dipstick tube 13 Air intake plenum Air intake plenum stay bolt M8 17 Air intake plenum stay bolt M10 35 Accelerator cable bracket 4 Bracke ...

  • Mitsubishi 6G7 - page 7

    6G7 ENGINE (E - W) - Specifications 1 1A-1-4 Items Nm Intake manifold Engine coolant temperature gauge unit 11 Engine coolant temperature sensor 29 Heater pipe bolt 18 W ater outlet fitting bolt 18 W ater inlet fitting bolt 18 Thermostat housing bolt 18 W ater pipe bolt 13 Delivery pipe 11 Intake manifold bolt 21 Fuel pipe bolt 8.8 Fuel pressure re ...

  • Mitsubishi 6G7 - page 8

    6G7 ENGINE (E - W) - Specifications 1 1A-1-5 Items Nm Oil pan, upper bolt 5.9 Baffle plate bolt (oil pan side) 11 Baffle plate bolt (cylinder block side) 9.8 Oil screen bolt 18 Relief plug 44 Oil pump case bolt 13 Oil pump cover bolt 9.8 Piston and connecting rod Connecting rod c ap 51 Crankshaft, flywheel and drive plate Flywheel bolt 74 Drive pla ...

  • Mitsubishi 6G7 - page 9

    6G7 ENGINE (E - W) - Specifications 1 1A-1-6 FORM-IN-PLACE GASKET The engine has several areas where the form-in-place gasket (FIPG) is in use. T o ensure that the gasket fully serves its purpose, it is necessary to observe some precautions when applying the gasket. Bead size, continuity and location are of paramount importance. T oo thin a bead co ...

  • Mitsubishi 6G7 - page 10

    6G7 ENGINE (E - W) - Special T ools 1 1A-2-1 2. SPECIAL TOOLS T ool Number Name Use MB991559 Camshaft oil seal installer adaptor Installation of camshaft oil seal (on left bank) (Used in combination with MD998713) MD998051 Cylinder head bolt wrench Loosening and tightening of cylinder head bolt MD998440 Leak-down tester Leak-down test of lash adjus ...

  • Mitsubishi 6G7 - page 11

    6G7 ENGINE (E - W) - Special T ools 1 1A-2-2 T ool Us e Name Number MD998774 V alve stem seal installer Installation of valve stem seal MD998780 Piston pin setting tool Removal and installation of piston pin MD998781 Flywheel stopper Holding flywheel or drive plate MD998767 T ensioner pulley Adjustment of timing belt tension MB990767 End yoke holde ...

  • Mitsubishi 6G7 - page 12

    6G7 ENGINE (E - W) - Alternator 1 1A-3-1 3. AL TERNA T OR REMOV AL AND INST ALLA TION 7EN1030 1 2 3 4 5 6 7 8 9 10 13 Nm 21 Nm 48 Nm 44 Nm 49 Nm 181 Nm Removal steps 1. T ensioner pulley A A "" A A 2. Crankshaft bolt 3. W asher 4. Crankshaft pulley 5. Alternator 6. Alternator bracket 7. Dip stick 8. O-ring 9. Dip stick tube 10. O-ring PWE ...

  • Mitsubishi 6G7 - page 13

    6G7 ENGINE (E - W) - Alternator 1 1A-3-2 REMOV AL SER VICE POINTS A A " CRANKSHAFT BOL T (1) With th e Special T ool fixed to th e drive plate or flywheel remove the crankshaft bolt. INST ALLA TION SERVICE POINTS " A A CRANKSHAFT BOL T (1) With th e Special T ool fixed to th e drive plate or flywheel install the crankshaft bolt. PWEE9615 ...

  • Mitsubishi 6G7 - page 14

    6G7 ENGINE (E - W) - Air Intake Plenum 1 1A-4-1 4. AIR INT AKE PLENUM REMOV AL AND INST ALLA TION 7EN1031 1 2 3 4 5 6 7 8 9 10 11 12 13 4N m 21 Nm 17 Nm 56 Nm 17 Nm 17 Nm 17 Nm 11 N m 11 N m 35 Nm Removal steps 1. Air intake plenum stay , front 2. Air intake plenum stay , rear 3. Accelerator cable bracket 4. EGR valve 5. EGR valve gasket 6. EGR pip ...

  • Mitsubishi 6G7 - page 15

    6G7 ENGINE (E - W) - Air Intake Plenum 1 1A-4-2 INST ALLA TION SERVICE POINTS " A A THROTTLE BODY GASKET (1) Install gasket with protrusion as illustrated. PWEE9615 E Dec. 1996 Mitsubishi Motors Corporation Protrusion 6AE0277 ...

  • Mitsubishi 6G7 - page 16

    6G7 ENGINE (E - W) - Ignition System 1 1A-5-1 5. IGNITION SYSTEM REMOV AL AND INST ALLA TION 7EN0965 1 2 3 4 1 23 Nm 25 Nm Removal steps 1. Spark plug cable 2. Spark plug 3. Distributor 4. O-ring PWEE9615 E Dec. 1996 Mitsubishi Motors Corporation ...

  • Mitsubishi 6G7 - page 17

    6G7 ENGINE (E - W) - Timing Belt 1 1A-6-1 6. TIMING BEL T REMOV AL AND INST ALLA TION 7EN0862 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Nm 88 Nm 23 Nm 44 Nm 48 Nm 13 Nm 11 N m 9N m 11 N m 44 Nm 13 Nm 44 Nm Removal steps 1. T iming belt front upper cover , rear 2. T iming belt front upper cover , front 3. Timing belt front lower co ...

  • Mitsubishi 6G7 - page 18

    6G7 ENGINE (E - W) - Timing Belt 1 1A-6-2 REMOV AL SER VICE POINTS A A " TIMING BEL T (1) When th e timing belt is to be reused, in order to allow re-installation of the belt so that it travels in the same direction as before it was removed, mark the direction of travel with an arrow before removing it. Caution D As water or oil on the belt ca ...

  • Mitsubishi 6G7 - page 19

    6G7 ENGINE (E - W) - Timing Belt 1 1A-6-3 (7) Badly worn teeth. Initial stage: Canvas is worn (fluffy canvas fibres are visible, rubber is gone and colour has changed to white. Canvas texture is not clear). Last stage: Canvas is worn out a nd rubber exposed a nd its width is reduced. (8) Missing tooth. AUT O-TENSIONER (1) Check for oil leaks. If oi ...

  • Mitsubishi 6G7 - page 20

    6G7 ENGINE (E - W) - Timing Belt 1 1A-6-4 2 Slowly close the vice to force th e rod in until th e set hole (A) of the rod is lined up with the set hole (B) of the cylinder . 3 Insert a metal wire (1.4 mm in diameter) into the set holes. 4 Remove the auto-tensioner from the vice. (2) Install the auto tensioner on the cylinder block through the oil p ...

  • Mitsubishi 6G7 - page 21

    6G7 ENGINE (E - W) - Timing Belt 1 1A-6-5 (8) Using t he Special T ool, turn the crankshaft counter- clockwise a quarter turn, then turn it clockwise and align the timing marks. Make sure that all timing marks are in alignment. Timing mark Crankshaft sprocket Right bank Left bank Timing mark Camshaft sprocket Camshaft sprocket T ensioner pulley Aut ...

  • Mitsubishi 6G7 - page 22

    6G7 ENGINE (E - W) - Timing Belt 1 1A-6-6 (9) Set the Special T ool and a torque wrench on the tensioner pulley . (10) T orque the tensioner pulley to 4.4 Nm. (1 1) While holding the tensioner pulley , tighten its centre bolt to the specified torque. (12) T urn the crankshaft 2 turns clockwise and let it stand for approx. 5 minutes. (13) Remove the ...

  • Mitsubishi 6G7 - page 23

    6G7 ENGINE (E - W) - Intake Manifold 1 1A-7-1 7. INT AKE MANIFOLD REMOV AL AND INST ALLA TION 7EN0874 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 13 Nm 11 N m 11 N m 29 Nm 18 Nm 18 Nm 18 Nm 18 Nm 21 Nm 9N m 9N m 18 Nm 14 Removal steps 1. Engine harness 2. Injector and delivery pipe 3. Insulator " H A 4. ...

  • Mitsubishi 6G7 - page 24

    6G7 ENGINE (E - W) - Intake Manifold 1 1A-7-2 INST ALLA TION SERVICE POINTS " A A O-RING / W A TER PIPE (1) Wet the O-ring (with water) to facilitate assembly . Caution D Keep the O-ring of oil or grease. " B A THERMOST A T (1) Install t he thermostat in th e thermostat case with its jiggle valve located at the t op position. " C A H ...

  • Mitsubishi 6G7 - page 25

    6G7 ENGINE (E - W) - Intake Manifold 1 1A-7-3 " F A INT AKE MANIFOLD (1) T ighten the nuts on the right bank to 5 - 8 Nm. (2) T ighten the nuts on the left bank to the specified torque. Then tighten the nuts on right bank to the specified torque. (3) T ighten the nuts on the left bank and those on the right bank again in that order . " G ...

  • Mitsubishi 6G7 - page 26

    6G7 ENGINE (E - W) - Exhaust Manifold & W ater Pump 1 1A-8-1 8. EXHAUST MANIFOLD & W A TER PUMP REMOV AL AND INST ALLA TION 7EN0966 1 2 3 4 5 6 7 8 9 49 Nm 13 Nm 35 Nm 13 Nm 49 Nm 41 Nm 23 Nm Removal steps 1. Heat protector , rear 2. Exhaust manifold, rear " B A 3. Exhaust manifold gasket, rear 4. Heat protector , front 5. Engine lift ...

  • Mitsubishi 6G7 - page 27

    6G7 ENGINE (E - W) - Exhaust Manifold & W ater Pump 1 1A-8-2 INST ALLA TION SERVICE POINTS " A A O-RING / W A TER PIPE (1) Wet the O-ring (with water) to facilitate assembly . Caution D Keep the O-ring free of oil grease. " B A EXHAUST MANIFOLD GASKET (1) Install gaskets with number 1 , 3 and 5 embossed on their top side to the right ...

  • Mitsubishi 6G7 - page 28

    6G7 ENGINE (E - W) - Rocker Arms and Camshaft 1 1A-9-1 9. ROCKER ARMS AND CAMSHAFT REMOV AL AND INST ALLA TION Apply engine oil to all moving parts before installation. 7EN0879 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 12 12 9 9 8 8 7 7 12 Nm 31 Nm 3.4 Nm Removal steps 1. Rocker cover 2. Gasket 3. Oil seal " E A 4. Oil seal A A " 5. Rocke ...

  • Mitsubishi 6G7 - page 29

    6G7 ENGINE (E - W) - Rocker Arms and Camshaft 1 1A-9-2 REMOV AL SER VICE POINTS A A " LASH ADJUSTER (1) Before removing t he rocker arms a nd rocker arm shafts, install the Special T ools to prevent the lash adjusters from falling off. INSPECTION CAMSHAFT (1) Measure the cam height. Standard value: IN: 37.71 mm EX: 37.14 m m Limit: IN: 37.21 m ...

  • Mitsubishi 6G7 - page 30

    6G7 ENGINE (E - W) - Rocker Arms and Camshaft 1 1A-9-3 INST ALLA TION SERVICE POINTS " A A CAMSHAFT (1) Before attaching the camshafts, apply engine oil to the journals an d cams. T ake care not to confuse the right bank and left bank camshafts. NOTE The right bank camshaft has 4-mm-wide slits in the rear end surface. (2) Make sure the camshaf ...

  • Mitsubishi 6G7 - page 31

    6G7 ENGINE (E - W) - Rocker Arms and Camshaft 1 1A-9-4 " D A ROCKER SHAFT SPRING (1) Insert the rocker shaft spring at a slant with respect to the spark plug guide a nd install it normal to the guide. " E A OIL SEAL PWEE9615 E Dec. 1996 Mitsubishi Motors Corporation 7EN0723 Rocker shaft spring 6AE0164 MD998713 7EN0724 Left bank side MD998 ...

  • Mitsubishi 6G7 - page 32

    6G7 ENGINE (E - W) - Cylinder Head a nd V alves 1 1A-10-1 10. CYLINDER HEAD AN D V AL VES REMOV AL AND INST ALLA TION Apply engine oil to all moving parts before installation. 7EN0915 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 108 Nm Removal steps A A " 1. Cylinder head bolt 2. W asher 3. Cylinder head assembly 4. Cylinder head g ...

  • Mitsubishi 6G7 - page 33

    6G7 ENGINE (E - W) - Cylinder Head a nd V alves 1 1A-10-2 REMOV AL SER VICE POINTS A A " CYLINDER HEAD BOL T A B " RET AINER LOCK (1) Attach a tag with the cylinder No. an d mounting location to the detached valves, springs an d other parts an d store them for reassembly . A C " V AL VE STEM SEAL Caution D Do not reuse the stem seal. ...

  • Mitsubishi 6G7 - page 34

    6G7 ENGINE (E - W) - Cylinder Head a nd V alves 1 1A-10-3 INSPECTION CYLINDER HEAD (1) Check the cylinder head for water leaks, gas leaks, damage or cracks before washing it. (2) Completely remove oil, fur , sealer , carbon and t he like. After washing the oil passages, blow air through them to make sure they are not clogged. (3) T o ensure flatnes ...

  • Mitsubishi 6G7 - page 35

    6G7 ENGINE (E - W) - Cylinder Head a nd V alves 1 1A-10-4 V AL VE GUIDE (1) Measure the clearance between the valve guide an d the valve stem. When t he clearance exceeds t he specified limit, change the valve guide or the valve or both. Standard value: Intake 0.02 - 0.04 mm Exhaust 0.04 - 0.06 mm Limit: Intake 0.10 mm Exhaust 0.15 mm V AL VE SEA T ...

  • Mitsubishi 6G7 - page 36

    6G7 ENGINE (E - W) - Cylinder Head a nd V alves 1 1A-10-5 V AL VE GUIDE REPLACEMENT PROCEDURE (1) Remove the snap ring from the exhaust valve guide. (2) Pull out to th e cylinder block side using a press. (3) Machine the valve guide hole in the cylinder head to match the oversize valve guide to be press fitted. Caution D Do not press fit another va ...

  • Mitsubishi 6G7 - page 37

    6G7 ENGINE (E - W) - Cylinder Head a nd V alves 1 1A-10-6 " B A V AL VE SPRING (1) Install the valve spring painted red side up. " C A V AL VE RET AINER LOCK (1) Using Special T ool install th e valve retainer lock. PWEE9615 E Dec. 1996 Mitsubishi Motors Corporation 6EN0544 Stem seal Spring seal Spring retainer Identification colour 7EN08 ...

  • Mitsubishi 6G7 - page 38

    6G7 ENGINE (E - W) - Oil Pan and Oil Pump 1 1A-1 1-1 1 1. OIL P AN AND OIL PUMP REMOV AL AND INST ALLA TION Apply engine oil to all moving parts before installation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Nm 23 Nm 9.8 Nm 41 Nm 13 Nm 18 Nm 9.8 Nm 11 N m 5.9 Nm 11 N m 39 Nm 44 Nm 9.8 Nm 9.8 Nm 11 N m 7EN0893 Removal steps " ...

  • Mitsubishi 6G7 - page 39

    6G7 ENGINE (E - W) - Oil Pan and Oil Pump 1 1A-1 1-2 REMOV AL SER VICE POINTS A A " OIL P AN (LOWER) (1) Apply wood to the oil pan side an d remove the oil pa n lower with a plastic hammer . A B " OIL P AN (UPPER) (1) Detach th e bolt (1) shown at left. (2) Detach all other bolts. (3) Screw a bolt into bolt hole A shown (at both ends) to ...

  • Mitsubishi 6G7 - page 40

    6G7 ENGINE (E - W) - Oil Pan and Oil Pump 1 1A-1 1-3 (2) Check for side clearance. Standard value: 0.04 - 0.10 mm (3) Check for body clearance. Standard value: 0.10 - 0.18 mm Limit: 0.35 mm INST ALLA TION SERVICE POINTS " A A OIL PUMP INNER AND OUTER ROTORS (1) Install th e oil pump outer rotor in t he proper direction using the setting mark d ...

  • Mitsubishi 6G7 - page 41

    6G7 ENGINE (E - W) - Oil Pan and Oil Pump 1 1A-1 1-4 " C A OIL SEAL " D A OIL P AN (UPPER) (1) Clean the gasket coating surfaces of t he cylinder block and the oil pan upper . (2) Squeeze out a 4 mm bead of liquid gasket and coat the coating surface with it. NOTE During attachment of the oil pan upper , the sealer must not be expelled fro ...

  • Mitsubishi 6G7 - page 42

    6G7 ENGINE (E - W) - Oil Pan and Oil Pump 1 1A-1 1-5 " E A OIL P AN (LOWER) (1) Clean the gasket coating surfaces of the oil p an upper and t he oil pan lower . (2) Squeeze out a 4 mm bead of liquid gasket and coat the coating surface with it. Liquid gasket: MITSUBISHI GENUINE Part No. MD970389 or equivalent " F A OIL FIL TER (1) Clean th ...

  • Mitsubishi 6G7 - page 43

    6G7 ENGINE (E - W) - Piston and Connecting Rod 1 1A-12-1 12. PISTON AN D CONNECTING ROD REMOV AL AND INST ALLA TION 7EN0424 1 2 3 4 5 6 7 8 9 10 11 12 51 Nm Apply engine oil to all moving parts before installation. Removal steps 1. Connecting rod cap n ut A A "" E A 2. Connecting rod cap 3. Connecting rod bearing, lower " D A 4. Pist ...

  • Mitsubishi 6G7 - page 44

    6G7 ENGINE (E - W) - Piston and Connecting Rod 1 1A-12-2 REMOV AL SER VICE POINTS A A " CONNECTING ROD CAP (1) Enter th e cylinder No. on the side of t he large end of the connecting rod to facilitate reassembly . A B " PISTON PIN The special piston pin setting tool (MD998780) consists of the parts shown at left. (1) Insert the special pu ...

  • Mitsubishi 6G7 - page 45

    6G7 ENGINE (E - W) - Piston and Connecting Rod 1 1A-12-3 INSPECTION PISTON RING (1) Check the clearance between the piston ring and the ring groove. If it exceeds the specified limit, change the ring or the piston and piston ring. Standard values: No. 1 0.03 - 0.07 mm No. 2 0.02 - 0.06 mm Limit: 0.1 mm (2) Place the piston ring in the cylinder bore ...

  • Mitsubishi 6G7 - page 46

    6G7 ENGINE (E - W) - Piston and Connecting Rod 1 1A-12-4 INST ALLA TION SERVICE POINTS " A A PISTON PIN (1) Measure the dimensions of t he following parts and portions: A: Piston pin mounting portion B: Distance between piston bosses C: Piston pin D: Connecting rod (2) Calculate by substituting each measured value into the following equation: ...

  • Mitsubishi 6G7 - page 47

    6G7 ENGINE (E - W) - Piston and Connecting Rod 1 1A-12-5 " B A OIL RING (1) Install th e oil ring spacer into th e piston ring groove. Next install the upper side rail into the piston ring groove, and then install the lower side rail. NOTE D There is no distinction between the upper and lower surfaces of the side rail and spacer . D The spacer ...

  • Mitsubishi 6G7 - page 48

    6G7 ENGINE (E - W) - Piston and Connecting Rod 1 1A-12-6 " D A PISTON AND CONNECTING ROD (1) Liberally coat the circumference of the piston, piston ring, and oil ring with engine oil. (2) Arrange the piston ring and oil ring gaps (side rail and spacer) as shown in th e figure. (3) Rotate the crankshaft so that the crank pin is positioned at th ...

  • Mitsubishi 6G7 - page 49

    6G7 ENGINE (E - W) - Crankshaft, Flywheel and Drive Plate 1 1A-13-1 13. CRANKSHAFT , FL YWHEEL AND DRIVE PLA TE REMOV AL AND INST ALLA TION Apply engine oil to all moving parts before installation. 7EN1032 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 74 Nm 11 N m 74 Nm 11 N m 93 Nm Removal steps 1. Adaptor plate 2. Drive plate 3. Plate 4. Adaptor p ...

  • Mitsubishi 6G7 - page 50

    6G7 ENGINE (E - W) - Crankshaft, Flywheel and Drive Plate 1 1A-13-2 INSPECTION CRANKSHAFT OIL CLEARANCE (PLASTIGAUGE METHOD) NOTE If the oil clearance exceeds th e limit, replace t he bearing, and crankshaft if necessary . This crankshaft oil clearance can be measured easily by using a plastic gauge, as follows: 1 Remove oil and grease and any othe ...

  • Mitsubishi 6G7 - page 51

    6G7 ENGINE (E - W) - Crankshaft, Flywheel and Drive Plate 1 1A-13-3 BORING CYLINDER (1) Oversize pistons to be used should be determined on the basis of th e largest bore cylinder . Piston size identification Size Identification mark 0.50 mm O.S. 0.50 1.00 mm O.S. 1.00 NOTE Size mark is stamped on the piston top. (2) Measure outside diameter of pis ...

  • Mitsubishi 6G7 - page 52

    6G7 ENGINE (E - W) - Crankshaft, Flywheel and Drive Plate 1 1A-13-4 INST ALLA TION SERVICE POINTS " A A CRANKSHAFT BEARING When bearing replacement is required, select and install the correct bearing by the following procedure. (1) Measure th e crankshaft journal diameter and confirm its classification from the following table. In the case of ...

  • Mitsubishi 6G7 - page 53

    6G7 ENGINE (E - W) - Crankshaft, Flywheel and Drive Plate 1 1A-13-5 (3) Select the correct bearing from the above table on the basis of the identification data confirmed at steps 1 and 2. Example D If the measured value of a crankshaft journal outer diameter is 59.996 mm, the journal is classified as “1” in the table. In case the crankshaft is ...

  • Mitsubishi 6G7 - page 54

    6G7 ENGINE (E - W) - Crankshaft, Flywheel and Drive Plate 1 1A-13-6 (4) Check the en d play . If it exceeds th e limit value, replace the thrust bearing. Standard value: 0.05 - 0.25 mm Limit: 0.3 mm " C A CRANKSHAFT REAR OIL SEAL (1) Using the Special T ool, press-fit a new crankshaft rear oil seal into the seal case. " D A OIL SEAL CASE ...

  • Mitsubishi 6G7 - page 55

    NOTES ...

Manufacturer Mitsubishi Category Air Conditioner

Documents that we receive from a manufacturer of a Mitsubishi 6G7 can be divided into several groups. They are, among others:
- Mitsubishi technical drawings
- 6G7 manuals
- Mitsubishi product data sheets
- information booklets
- or energy labels Mitsubishi 6G7
All of them are important, but the most important information from the point of view of use of the device are in the user manual Mitsubishi 6G7.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Mitsubishi 6G7, service manual, brief instructions and user manuals Mitsubishi 6G7. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Mitsubishi 6G7.

A complete manual for the device Mitsubishi 6G7, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Mitsubishi 6G7 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Mitsubishi 6G7.

A complete Mitsubishi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Mitsubishi 6G7 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Mitsubishi 6G7, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Mitsubishi 6G7, that we can find in the current document
3. Tips how to use the basic functions of the device Mitsubishi 6G7 - which should help us in our first steps of using Mitsubishi 6G7
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Mitsubishi 6G7
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Mitsubishi 6G7 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Mitsubishi 6G7?

Use the form below

If you did not solve your problem by using a manual Mitsubishi 6G7, ask a question using the form below. If a user had a similar problem with Mitsubishi 6G7 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)