Manual Fujitsu CG-301

28 pages 0.34 mb
Download

Go to site of 28

Summary
  • Fujitsu CG-301 - page 1

    INSTRUCTION MANUAL CCD CAMERA CG-301 Series ...

  • Fujitsu CG-301 - page 2

    RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. En-1 W ARNING – T O PREVENT RISK OF FIRE OR SHOCK, DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE. PRECAUTION : DO NOT REMOVE ANY COVER WHILE THE ...

  • Fujitsu CG-301 - page 3

    CONTENTS Section P a g e IMPORT ANT SAFEGUARDS 3 INTRODUCTION 5 CAUTIONS FOR OPERA TION 5 EXTERNAL CONTROLS AND CONNECTORS 6 L E N S 7 ELECTRONIC C ONNECTIONS 7 MECHANICAL CONNECTION 7 BACK FOCAL ADJUSTMENT 8 POWER CONNE CTION 9 AC POWER CONNECTION 9 DC POWER CONNECTION 9 SETUP MENU 10 SETTING METHOD 12 SETTING OPERA TION 13 SETUP ITEMS 13 M O D E ...

  • Fujitsu CG-301 - page 4

    IMPORT AN T SAFEGUARDS 1. Read Instructions–All the safety and operating in structions should b e read before the camera is operated. 2. Retain Instructions–The safety and operating inst ructions should be retained for future reference. 3. Heed W arnings–All warnings on the camera and in the operating instructions should be adhered to. 4. Fol ...

  • Fujitsu CG-301 - page 5

    14. Overloading–Do not overload wall outlet and extension cord, as this can result in a risk of fire or electric shock. 15. Object and Liquid Entry–Never push objects of any kind into the ca mera through openings, as they may touch dangerous voltage points or short-out p arts that could re sult in a fire or electric shock. Never spill liquid of ...

  • Fujitsu CG-301 - page 6

    INTRODUCTION Thank you for purchasing this product. This pr oduct is a mult iple function and a high quality CCD camera developed considering a high-end security . The following functions are built-in: (1) Wide Dynamic Range function This function makes it possible to capture both high-luminance and low -luminance subjects. Dynamic Range of max.60 ...

  • Fujitsu CG-301 - page 7

    EXTERNAL CONTROLS AND CONNECTORS TOP/FRONT VIEW 3 3 2 1 CAMERA MOUNT ADAPTER 6 8 9 10 4 7 5 BACK VIEW ① Lens Mou nt The camera has a standard CS lens mount but can use a C-moun t lens when a C/CS-moun t adapter is installed between the lens an d camera. ② Back Focus Lock Screw Loosen to adjust the back f ocus to match the lens attached to the C ...

  • Fujitsu CG-301 - page 8

    LENS This camera can accommodate DC voltage drive auto-iris lens. VIDEO signal co ntrolled lens is not available. ELECTRONIC CONNE CTIONS T able.1 shows wiring scheme for the 4pin Auto iris connector . Lens Connector Auto-iris Lens 21 43 (View from wiring side of plug) Fig. 2 Table 1 DC VOLTAGE DRIVE AUTO-IRIS LENS 1 2 3 4 CONT. ( ) CONT. (+) DRIVE ...

  • Fujitsu CG-301 - page 9

    BACK FO CAL L ENGTH ADJUSTMENT The camera h as been factory -adjusted for the proper back focal lengt h using a sta ndard CS Mount le ns. However , when the lens is mounted, it may be necessary t o readjust back focal length to match the lens bein g used. Fig.4 10mm 50mm CAMERA Approx.15 ALLEN WRENCH For zoom lens: 1. With the camera in op eration, ...

  • Fujitsu CG-301 - page 10

    POWER CONNECTION This camera uses 24V AC or 12VDC power sup ply for the m ain supply . AC PO WER CONNECT ION A main supply of 24V AC (20.4 to 27.6 V AC) 50 / 60Hz is required. This main supply must also have a minim um rating of 270m A. Remove the sheath at the end of power cord in the length of 10mm. T wist and strai ghten the wir es, then insert ...

  • Fujitsu CG-301 - page 11

    SETUP MENU This product built in OSD function and can customize the camera setting. The menu list is shown in the following. MAIN MENU MODE SELECT EXPOSURE SE T . FUNCTION SET . CAMERA SETUP LENS ADJUSTMENT MODE SA VE BLEMISH COM PENSA TION INITIALIZE E N D MODE SELECT ST A NDARD DA Y&NIGHT WID E CASINO USER MODE RETURN END LENS ADJUSTMENT O K ...

  • Fujitsu CG-301 - page 12

    CHROMA RY GAIN → - 1 BY GAIN → - 2 RY HUE → 1 BY HUE → 1 RETURN END SYNC SELEC T SYNC MODE AUTO P H A S E → RETURN END E-ZOOM ZOOM → OFF POSITION RETURN END MASKING MASK → OFF MASK EDIT MASK ERASE RETURN END TITLE TITLE → OFF TITLE EDIT RETURN END PHASE SHIF T Phase V alue = 28 POSITION MASK SETTING TITLE EDIT ABCDEFGHIJKLM NOPQRSTU ...

  • Fujitsu CG-301 - page 13

    SETTING METHOD This camera has multiple functions , and can be adapt ed to a shooting place. There are 2 methods which are spec ified functions of the camera. (1) Setting method by using OSD(On-screen Display) function. Refer to the next section in det ails. (2) Setting method by using Direct-key function. This camera has Direct-key functi on. This ...

  • Fujitsu CG-301 - page 14

    SETTING OPERA T ION This camera has OSD function. T o change setti ngs on the menu, operate the following procedure. 1. Press and hold down the SW for 2 seconds or mo re. The SW on the rear p anel is used. (Fig.1 ⑧ ) 2. MAIN MENU appears on the monitor as shown in Fig.7-5. 3. Move the cursor to an item you want to change by using the SW . The men ...

  • Fujitsu CG-301 - page 15

    Parameters of each mode is shown in Fig.7-7,7-8,7-9,7-10. ST ANDARD Fig. 7-7 Setting parameters of ST ANDARD DA Y&NIGHT Fig.7-8 Setting parameters of DA Y&NIGHT WIDE Fig.7-9 Setting parameters of WIDE CASINO Fig. 7-10 Setting parameters of CASINO En-14 EXPOSURE SE T . A E M O D E L E V E L F L I C K E R L E S S A G C S E N S U P D A Y & ...

  • Fujitsu CG-301 - page 16

    (2) EXPOSURE SET . In this menu, the exposure system of the camera can be specified. There are 2 kinds of EXPOSURE SET . menu. A. AE MODE other than MANUAL B . MANUAL is select ed for AE MOD E Fig. 8-1 EXPOSURE SET . menu AE MODE AE operation mode can be selected. WD → NORMAL → BLC → MANUAL The mode turns in this order . WD : Wide Dynamic Ran ...

  • Fujitsu CG-301 - page 17

    DA Y & NIGHT This item specifies the switch betw een Color and BW picture. AUTO : Auto mo de enables the camera to switch between Color and BW picture in response to light condition. COLOR : Fixes to Color picture. BW : Fixes to BW picture. EXT . : This mode allows the camera to control by the external signal. Refer to the section on EXTERNAL C ...

  • Fujitsu CG-301 - page 18

    (3) FUNCTION SET . In this menu, functions other than exposure sy stem can be specified. Fig.9-1 FUNCTION SET . menu (3-1)SYNC SELECT This camera supports the sy nchronizati on mode such as line lock and internal. Fig.9-2 SYNC SELECT menu SYNC MODE The synchronization mode can be selected. AUT O : At AC power supply , this mode allows the camera to ...

  • Fujitsu CG-301 - page 19

    (3-2) WHITE BALANCE WHITE BALANCE Y ou can select one of 4 modes for white balance adjustment as follows. AUTO, HOLD, INDOOR (Approx. 2800K), OUTDOOR (Approx. 6000K) AUTO : The white balance is adjusted automatically to provide the optimum picture. HOLD : In this mode, the WB gain just before changing to this mode is kept. INDOOR, OUTDOOR : These m ...

  • Fujitsu CG-301 - page 20

    ( 3-5) E-ZO OM This camera built in electronic zoom, elec tronic pannin g and electronic tilting function. In this menu, these functions is specif ied. Fig.9-5 E-ZOOM menu ZOOM The zoom magnification is selected from the following. OFF , 1.5, 2.0, 2.5 Note) When 1.5, 2.0 or 2.5 is selected, WD and MASKING function is not available. POSITION When th ...

  • Fujitsu CG-301 - page 21

    3. The pointer is displayed on the monitor screen. T he area of a mask can be edited by using this pointer . At first, move the cursor to the upper left position you want to make a mask and press the SW . Next, move the cursor to the lower right pos ition you want to make a mask and press the SW . In the above procedure, a mask can be made. MASK ER ...

  • Fujitsu CG-301 - page 22

    (4) CAMERA SETUP This camera has an external control input inte rface (RS-485). All p arameters and adjustments can be changed from an external unit. Refer to the section on External Control Input T erminal in details. In this menu, setting of the communication, LED and Sw itch can be selected. Fig.10 CAMERA SETUP menu ADDRESS The number to identif ...

  • Fujitsu CG-301 - page 23

    (6) MODE SA VE Current settings can be saved. Saved settings can read by selecting USER MODE of MODE SELECT . Fig.12 MODE SA VE menu Operation procedure 1. After changing parameters and adjustment s, move the cursor to MODE SA VE and press the SW . MODE SA VE menu is displayed. 2. Move the cursor to OK and press the SW . Parameters and adjustments ...

  • Fujitsu CG-301 - page 24

    (8) INITIALIZE Present settings are reset to the factory default settings. Fig. 8 INITIALIZE MENU Fig.14 INITIALIZE menu Operation procedure 1. Move the cursor to INITIALIZE and press the SW . INITIALIZE menu is displayed. 2. Move the cursor to OK and press the SW . All parameters and adjustments are reset to the factory default settings. 3. The sc ...

  • Fujitsu CG-301 - page 25

    EXTERNAL CONTROL INPU T TERMINAL This camera has an external control input terminal and can be operated remotely by supplying a control signal to this terminal. CONNECTIONS Connections of control signals are a s follows. Pin1 Pin7 Magnified Figure Fig.16 Pin No. Description 1 A (+) 2 B (-) 3 GND 4 A (+) 5 B (-) 6 GND 7 D&N Control Signal Input ...

  • Fujitsu CG-301 - page 26

    SETUP T o make up the camera system with RS-485, do the following procedure. Setting procedure 1. Connect the cable for each camera. 2. T erminate the camera installed in the end of the sy stem. T urn off the termination of other cameras. Refer to Fig.1 ⑥ 3. Set the address number for each camera on CAMERA SETUP menu. Notice so that t he number i ...

  • Fujitsu CG-301 - page 27

    SPECIFICA TIONS Model Name CG-301 TV System NTSC P AL Power AC24V(±15%) / DC12V(±15%) Power Consumption 270mA(24V AC) / 390mA(12VDC) Imager 1/3” Image Format v ertical double density Interline transfer CCD Picture Element s (active) Approx. 380K pix els Approx. 440K pix els Synchronizati on Internal / Li neLock Signal to Noise Ratio 48dB(AGC of ...

  • Fujitsu CG-301 - page 28

    FUJITSU GENERAL LIMITED 1 1 16, Suenaga, T akatsu-ku, Kawasaki 213-8502, Japan ...

Manufacturer Fujitsu Category Camcorder

Documents that we receive from a manufacturer of a Fujitsu CG-301 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- CG-301 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu CG-301
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu CG-301.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu CG-301, service manual, brief instructions and user manuals Fujitsu CG-301. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu CG-301.

Similar manuals

A complete manual for the device Fujitsu CG-301, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu CG-301 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu CG-301.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu CG-301 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu CG-301, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu CG-301, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu CG-301 - which should help us in our first steps of using Fujitsu CG-301
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu CG-301
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu CG-301 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu CG-301?

Use the form below

If you did not solve your problem by using a manual Fujitsu CG-301, ask a question using the form below. If a user had a similar problem with Fujitsu CG-301 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)