English dropdown-ico

Manual Univex EPX-80DHPT

20 pages 0.8 mb
Download

Go to site of 20

Summary
  • Univex EPX-80DHPT - page 1

    1 State – Premier ® Hybrid Electric Heat Pump W ater Heater Installation Instructions and Use & Care Guide T o obtain technical, warranty or service assistance during or after the installation of this water heater , call toll free 1-800-365-0024 When calling for assistance, please have the following information ready: 1. Model number 2. 7 Di ...

  • Univex EPX-80DHPT - page 2

    2 Y our safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety aler ...

  • Univex EPX-80DHPT - page 3

    3 INST ALLING YOUR W A TER HEA TER Consumer Information This water heater should be installed in accordance with the local code authority having jurisdiction, the power company or electric utility , and this installation manual. In the absence of local code requirements, follow the regulations set forth in the latest edition of The National Electri ...

  • Univex EPX-80DHPT - page 4

    4 Figure 3 Residential Garage Installation Vehicle Stop Drain Drain Pan NOTE: The water heater shall be located so it is not subject to physical damage by moving vehicles or area fl ooding. State of California NOTE: The water heater must be braced, anchored, or strapped to avoid moving during an earthquake. Contact local utilities for code require ...

  • Univex EPX-80DHPT - page 5

    5 W ater System Piping Piping, fi ttings, and valves should be installed according to the installation drawing (Figure 4). If the indoor installation area is subject to freezing temperatures, the water piping must be properly insulated. W ater supply pressure should be 50-60 PSIG and not exceed the maximum 80 PSIG. If the supply line pressure exce ...

  • Univex EPX-80DHPT - page 6

    6 Please note the following: • The system should be installed only with piping that is suitable for potable (drinkable) water such as copper , CPVC, or polybutylene. This water heater must not be installed using iron piping or PVC water piping. • Use only pumps, valves, or fittings that are compatible with potable water . • Use only full flow ...

  • Univex EPX-80DHPT - page 7

    7 T o reduce the risk of excessive pressures and temperatures in this water heater , install temperature and pressure relief protective equipment required by local codes, but no less than a combination temperature and pressure relief valve certi fi ed by a nationally recognized testing laboratory that maintains periodic inspection of the productio ...

  • Univex EPX-80DHPT - page 8

    8 Locate the hot water (outlet) & cold water (inlet) pipes 4. to the water heater . Locate the slit running the length of a section of pipe 5. insulation. Spread the slit open and slip the insulation over the 6. cold water (inlet) pipe. Apply gentle pressure along the length of the insulation to ensure that it is fully seated around the pipe. A ...

  • Univex EPX-80DHPT - page 9

    9 Figure 8A Junction Box Ground Wire Conduit (Field Connection) Black Wire Red Wire Green Ground Wire Red Black Approved Connectors Figure 9 Wiring Diagram Overload Protection T o 240v 1 Phase Power supply Electrical Service ground L1 L2 Circuit Breaker Ground Wire Green Connecting the Condensate Pump Over fl ow Shut Off Switch T urn off power to ...

  • Univex EPX-80DHPT - page 10

    10 W ater Heater Location Centrally located with the water piping system. □ The fl ooring beneath the water heater must be able to □ support the weight of the water heater when fi lled with water (967 lbs. full). Located indoors (such as a basement or garage) □ and in a vertical position. Sheltered from freezing temperatures. Provisions mad ...

  • Univex EPX-80DHPT - page 11

    11 OPERA TING YOUR W A TER HEA TER Before Using Make sure the water heater has been properly 1. installed. See “Installing Y our W ater Heater” section. Make sure the air filter is correctly seated, as it may 2. shift during shipping or installation. See “Repair Parts Illustration” section. Completely fill the tank with water (See “W ater ...

  • Univex EPX-80DHPT - page 12

    12 Adjusting the User Interface Module/Operational Modes °F/°C LOCK HEAT PUMP ELEMENT EFFICIENCY F VACA TION ELECTRIC HYBRID EFFICIENCY Power Button: On - Green Standby - Red T emperature Down (Decrease) Button T emperature Up (Increase) Button Operational Mode Buttons Wa t e r T emperature Set Point W ater Heater Mode/Status Indicator W ater Hea ...

  • Univex EPX-80DHPT - page 13

    13 Operational Conditions Powered Anode Operation T o shelter the glass-lined water tank from corrosion through electrolysis, this water heater is equipped with a non-sacrificial powered anode which should not need to be replaced under normal operating conditions. If the powered anode malfunctions it should be replaced by a qualified technician. IM ...

  • Univex EPX-80DHPT - page 14

    14 MAINTENANCE OF YOUR W A TER HEA TER T emperature and Pressure Relief V alve Manually operate the temperature and pressure relief valve at least once a year to make sure it is working properly . T o prevent water damage, the valve must be properly connected to a discharge line which terminates at an adequate drain. Standing clear of the outlet (d ...

  • Univex EPX-80DHPT - page 15

    15 Remove the access cover(s), then remove the foam 4. insulation block. Remove the protective plastic cover(s) over the 5. elements from their attachment point. Disconnect the electrical wires from the heating 6. element(s) by loosening the screws (Figure 12). Remove the screw-in element(s) by turning the element(s) counterclockwise with a 1-1/2 i ...

  • Univex EPX-80DHPT - page 16

    16 DIAGNOSTIC CODES DISPLA Y SHOWS INDICA TES CORRECTIVE ACTION UPPER ELEMENT CONNECT F AUL T 1. Upper element is not functioning T urn off power at the circuit breaker/fuse 1. box and check for a loose connection at the element. For access directions see “Heating Element Replacement” section. If error persists proceed to the next step. Replace ...

  • Univex EPX-80DHPT - page 17

    17 TROUBLESHOOTING CHART PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION NO HOT W A TER Hot water usage pattern exceeds the 1. capability of the water heater in current mode No power to the water heater 2. Unit in standby 3. Unit in V acation mode 4. High temperature limit switch open 5. Non-functioning upper temperature 6. sensor Change to different m ...

  • Univex EPX-80DHPT - page 18

    18 REP AIR P ART ILLUSTRA TION ITEM NO. P ARTS DESCRIPTION 1 Upper Access Cover 2 Lower Access Cover 3 Upper Element (4500 W atts) 4 Lower Element (2000 W atts) 5 Energy Cut-Off (ECO) Switch 6 T emperature & Pressure Relief V alve (T&P) 7 Dip T ube (at hot water outlet) 8 Powered Anode Rod 9 User Interface Module 10 Air Filter 11 Air Inlet ...

  • Univex EPX-80DHPT - page 19

    19 NOTES ...

  • Univex EPX-80DHPT - page 20

    20 Copyright © 2010 State Industries, Inc. All rights reserved. ...

Manufacturer Univex Category Water Heater

Documents that we receive from a manufacturer of a Univex EPX-80DHPT can be divided into several groups. They are, among others:
- Univex technical drawings
- EPX-80DHPT manuals
- Univex product data sheets
- information booklets
- or energy labels Univex EPX-80DHPT
All of them are important, but the most important information from the point of view of use of the device are in the user manual Univex EPX-80DHPT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Univex EPX-80DHPT, service manual, brief instructions and user manuals Univex EPX-80DHPT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Univex EPX-80DHPT.

Similar manuals

A complete manual for the device Univex EPX-80DHPT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Univex EPX-80DHPT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Univex EPX-80DHPT.

A complete Univex manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Univex EPX-80DHPT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Univex EPX-80DHPT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Univex EPX-80DHPT, that we can find in the current document
3. Tips how to use the basic functions of the device Univex EPX-80DHPT - which should help us in our first steps of using Univex EPX-80DHPT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Univex EPX-80DHPT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Univex EPX-80DHPT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Univex EPX-80DHPT?

Use the form below

If you did not solve your problem by using a manual Univex EPX-80DHPT, ask a question using the form below. If a user had a similar problem with Univex EPX-80DHPT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)