Manual Pelco CM9700-SER-32

16 pages 1.24 mb
Download

Go to site of 16

Summary
  • Pelco CM9700-SER-32 - page 1

    CM9700-SER-32 Port Expander INSTALLATION/OPERATION C579M-A (5/05) ...

  • Pelco CM9700-SER-32 - page 2

    ...

  • Pelco CM9700-SER-32 - page 3

    C579M-A (5/05) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco CM9700-SER-32 - page 4

    4 C579M-A (5/05) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This ...

  • Pelco CM9700-SER-32 - page 5

    C579M-A (5/05) 5 Installation The CM9700-SER-32 port expander assembly increases by 32 the number of available Sercom (serial communication) ports in a node-based CM9700-CC1 via the installation of an RP (rocket port) PCI expansion card. A maximum of 120 total ports can be achieved by using three CM9700-SER-32 assemblies in conjunction with the Ser ...

  • Pelco CM9700-SER-32 - page 6

    6 C579M-A (5/05) e. Reinstall the top cover and secure with mounting screws. Figure 2. Removing the CC1 T op Cover Figure 3. CC1 Internal Layout 3. Mount external hardware. Refer to Figure 1 and do the following: a. Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit. The data cables are three feet in length. ...

  • Pelco CM9700-SER-32 - page 7

    C579M-A (5/05) 7 e. Connect peripherals to desired expansion ports. Refer to RP1 in Figure 4. Figure 4. Rocket Card to Expansion Port Control Association 4. Apply power to the CC1. After applying power , press the Delete key on the keyboard to enter into the BIOS menu settings, and then do the following: a. After “ENTER CURRENT P ASSWORD” appea ...

  • Pelco CM9700-SER-32 - page 8

    8 C579M-A (5/05) 4 SERCOM CARDS, 2 ROCKET PORT CARDS, COM 2 UNAVAILABLE (96 T OTAL PORTS) 1. T urn off all power to the CC1. Disconnect and label all attached cabling. 2. Install the RP cards into the CC1. Refer to Figure 2 and Figure 3 and do the following: a. Remove the top cover mounting screws. b. From the rear , tilt the top cover up at a slig ...

  • Pelco CM9700-SER-32 - page 9

    C579M-A (5/05) 9 8. Scroll down to PERIPHERAL SETTINGS, press Enter , and then do the following: a. Scroll down to ONBOARD SERIAL PORT 2. b. Change the setting to DISABLED by pressing Page Down. c. Press Esc. d. Scroll down to SA VE SETTINGS AND EXIT and type Y e. Press Enter . 9. Reboot machine by pressing Ctrl+Alt+Del. 3 SERCOM CARDS, 2 ROCKET PO ...

  • Pelco CM9700-SER-32 - page 10

    10 C579M-A (5/05) Figure 5. Sercom Card Mounting Plate Removal NOTE: If the VGA card is present in PCI slot 2, remove the retaining screw and gently pull the card up. Reinstall the card into PCI slot 4 (follow steps d, e, and f, applying them to the VGA card and PCI slot 4). d. Remove the retaining screw and slot cover for PCI slot 2. Slide the cov ...

  • Pelco CM9700-SER-32 - page 11

    C579M-A (5/05) 11 Figure 7. CM9700-ADP-120 Adapter Plate Installation 6. Reinstall the top cover and secure with mounting screws. 7. Mount external hardware. Refer to Figure 1 and do the following: NOTE: This procedure is for each individual port expansion assembly (one RP card and port expansion unit) and is to be duplicated for each RP card insta ...

  • Pelco CM9700-SER-32 - page 12

    12 C579M-A (5/05) 3 SERCOM CARDS, 3 ROCKET PORT CARDS, COM 2 UNAVAILABLE (120 T OTAL PORTS) 1. T urn off all power to the CC1. Disconnect and label all attached cabling. 2. Remove the top cover mounting screws (refer to Figure 2). 3. From the rear , tilt the top cover up at a slight angle, and then pull backwards away from the front edge to remove ...

  • Pelco CM9700-SER-32 - page 13

    C579M-A (5/05) 13 7. Mount external hardware. Refer to Figure 1 and do the following: NOTE: This procedure is for each individual port expansion assembly (one RP card and port expansion unit) and is to be duplicated for each RP card installed in the CM9700-CC1. Power should not be applied until all physical connections have been secured. a. Mount t ...

  • Pelco CM9700-SER-32 - page 14

    14 C579M-A (5/05) ...

  • Pelco CM9700-SER-32 - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco CM9700-SER-32 - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Manufacturer Pelco Category MP3 Player

Documents that we receive from a manufacturer of a Pelco CM9700-SER-32 can be divided into several groups. They are, among others:
- Pelco technical drawings
- CM9700-SER-32 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco CM9700-SER-32
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco CM9700-SER-32.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco CM9700-SER-32, service manual, brief instructions and user manuals Pelco CM9700-SER-32. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco CM9700-SER-32.

Similar manuals

A complete manual for the device Pelco CM9700-SER-32, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco CM9700-SER-32 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco CM9700-SER-32.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco CM9700-SER-32 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco CM9700-SER-32, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco CM9700-SER-32, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco CM9700-SER-32 - which should help us in our first steps of using Pelco CM9700-SER-32
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco CM9700-SER-32
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco CM9700-SER-32 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco CM9700-SER-32?

Use the form below

If you did not solve your problem by using a manual Pelco CM9700-SER-32, ask a question using the form below. If a user had a similar problem with Pelco CM9700-SER-32 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)