Manual Ingersoll-Rand 8509-A

18 pages 1.2 mb
Download

Go to site of 18

Summary
  • Ingersoll-Rand 8509-A - page 1

    OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION MANUAL Released: M30 33 3-l-77 Tool Products Revised: l-27-95 “O” SERIES “QRT” SCREWDRIVERS Models: 8506-A( ), 8509-A( ), 8515-A( ) and 8521-A( ). 1018-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE ...

  • Ingersoll-Rand 8509-A - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. I I Wear hearing protection when operating this tool. Turn off air supply and disconnect air supply hose before installing, . removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. A WARNING Do not carry the tool by the hose. Air powered ...

  • Ingersoll-Rand 8509-A - page 3

    ROUTINE LUBRICATION REQUIREMENTS M30 33 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not ...

  • Ingersoll-Rand 8509-A - page 4

    MODEL IDENTIFICATION MODELS WITH -EU SUFFIX ARE “EC” COMPLIANT MODELS. NOTE: GENERAL PURPOSE WRENCH 37167 FURNISHED WITH -A AND -T MODELS. DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air before performing maintenance or service to tool. DRIVE SECTION Remove clut ...

  • Ingersoll-Rand 8509-A - page 5

    DRIVE SECTION M30 ADJUSTABLE CLUTCH 33 CLUTCH ADJUSTMENT Remove clutch assembly (36310) from tool. Place pin in hole of jaw (36318) or wrench on square end of spindle (36311) to adjust nut (36313). To adjust properly, release nut to least tension. Tight- en nut one or two positions -each click = one position. Assemble clutch to tool and test torque ...

  • Ingersoll-Rand 8509-A - page 6

    DRIVE SECTION TORQMATIC CLUTCH CLUTCH ADJUSTMENT Remove clutch assembly from tool. Place wrench on square end clutch. Clutch assembly should contain approximately 1/8 oz. (3.5 of spindle (38322) to adjust nut (38313). To adjust properly, re- g) of grease. lease nut to least tension. Tighten nut one or two positions -each a. click = one position. As ...

  • Ingersoll-Rand 8509-A - page 7

    ...

  • Ingersoll-Rand 8509-A - page 8

    GEARING SECTION DRIVE GEARING DISASSEMBLY a. b. Remove spindle and components from ring gear. To remove gears from spindle, remove bearing, spacer and shafts. ASSEMBLY NOTE: Pack bearings and lubricate gears liberally with ARO 33153 grease upon assembly. Gearing assembly should contain approximately 1/8 oz. (3.5 g) of grease. a. Assemble spacer (33 ...

  • Ingersoll-Rand 8509-A - page 9

    GEARING SECTION M30 AUXILIARY GEARING 33 DISASSEMBLY a. Grasp adapter (ring gear) in one hand and tap splined end of spindle with a soft face hammer; spindle and components will 33153 grease upon assembly. Gearing should contain approxi- loosen from adapter. mately 118 oz. (3.5 g) of grease. a. b. To remove gears from spindle, remove bearing, space ...

  • Ingersoll-Rand 8509-A - page 10

    MOTOR SECTION DISASSEMBLY a. Remove motor from housing. Grasp cylinder in one hand and tap splined end of rotor with a soft face hammer; motor will assemble over rotor, aligning air inlet holes of cylinder with air come apart. inlet slots of end plate. d. Coat blades (31363) with ARO 29665 spindle oil and as- ASSEMBLY semble to rotor slots - straig ...

  • Ingersoll-Rand 8509-A - page 11

    HEAD SECTION M30 33 DISASSEMBLY a. Remove roll pin (Y178-25), releasing trigger (45469). b. Remove screw (Y222-156-C) releasing shroud (45468). c. Grasp end of valve assembly (47880) and pull to remove valve assembly and bushing (45465). d. Remove retaining ring (Y147-68), releasing screens (42911) and muffler (45474). ASSEMBLY NOTE: Whenever a par ...

  • Ingersoll-Rand 8509-A - page 12

    QTY 1 1 5 6 1 1 1 2 1 PART NUMBER 31092 31093 31363 36317 41795 41799 41954 42911 45474 SERVICE KIT NO. 42114 FOR SERVICING ADJUSTABLE CLUTCH MODELS DESCRIPTION SPRING THRUST PIN BLADE PIN MOTOR OIL GEAR LUBE “O” RING LUBE SCREEN MUFFLER PART QTY NUMBER 6 Y16-205 1 Y147-68 1 Y178-25 2 Y180-13 2 Y325-7 2 Y325-11 2 Y325-12 2 Y325-13 SERVICE KIT N ...

  • Ingersoll-Rand 8509-A - page 13

    ACCESSORIES 44361-( ) PIPED EXHAUST SYSTEM ASSEMBLY M30 33 30302-( ) INLET HOSE - 5/16” I.D. 1/4” P.T.F. THREAD P.T.F. THREAD TO AIR SUPPLY 46672-l ADAPTER ASSEMBLY 2622 HOSE ADAPTER 3/8” MALE N.P.T.F. 1/2” I.D. 43551-6 MUFFLER 3/8” FEMALE N.RT.F. PIPED EXHAUST ASSEMBLY CONSISTS OF 5/16” I.D. AIR INLET HOSE WlTH IN” MALE FlTTlNG AT EA ...

  • Ingersoll-Rand 8509-A - page 14

    ACCESSORIES HOUSING AND ADAPTER ASSEMBLIES FlNDER ADAPTER IS PRESSED INTO HOUSING. FINDER ADAPTER 39332 HOUSING ASSEMBLY HOUSlNG AND FINDER ADAPTER -USE WITH FlNDERS 36106-(), 36105-(), 41292-() AND 41292-(). ALSO USE WITH GUIDES 30334-(), 40261 AND 41767. ALSO FOR USE WITH BALL LOCK ADAPTER ASSEMBLY 44699 WITHOUT USE OF GUIDE BUSHING. . ASSEMBLY N ...

  • Ingersoll-Rand 8509-A - page 15

    ACCESSORIES FINDERS EXTENSION FINDER FOR 1/4” HEX BITS M30 33 NOTE: SPRING 30111 AND LOCK SPRING 31574 REQUIRED FOR USE WITH FINDERS (ORDER SEPARATELY). USE WITH FINDER ADAPTER 36332. BELL MOUTH FINDER FOR 1/4” HEX BITS Similar to standard finders except that each finder will accept mm sizes and types of screw heads. NOTE: SPRING 36111 AND LOCK ...

  • Ingersoll-Rand 8509-A - page 16

    ACCESSORIES BITS AND BIT HOLDERS 1/4” HEX DRIVE BITS EXTENSION BLADED BITS FOR SLOTTED SCREWS. PART NO. LENGTH POINT SIZE SHAFT DIA. 30320-l 1-15/16” 1 .182” 30320-2 1-15/16” 2 .246” PHILLIPS BITS 30320-3 1-15/16” 3 .310” 31531-1 2-3/4” 1 .182” 31531-2 2-3/4” 2 .246” 315313 2-3/4” 3 .310” REED & PRINCE BITS . PART NO. ...

  • Ingersoll-Rand 8509-A - page 17

    SOCKET HEAD DRIVERS MAGNETIC BIT HOLDER USE WITH GUIDE BUSHING 46261. SQUARE DRIVE ADAPTERS USE WITH GUIDE BUSHING 30334-( ). ACCESSORIES M30 BITS AND BIT HOLDERS 33 HEX BALL LOCK ADAPTER PART NO. LENGTH HEX SETSCREW CAP SCREW SHAFT DIA. SIZE SIZE SIZE 30370-2 3/32” #10-#12 #4-#5 .187” 30370-3 1/8” 1/4 .187” 30370-4 5/32” 5/16 #10 .187” ...

  • Ingersoll-Rand 8509-A - page 18

    PN 49999-032 ...

Manufacturer Ingersoll-Rand Category Power Screwdriver

Documents that we receive from a manufacturer of a Ingersoll-Rand 8509-A can be divided into several groups. They are, among others:
- Ingersoll-Rand technical drawings
- 8509-A manuals
- Ingersoll-Rand product data sheets
- information booklets
- or energy labels Ingersoll-Rand 8509-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ingersoll-Rand 8509-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ingersoll-Rand 8509-A, service manual, brief instructions and user manuals Ingersoll-Rand 8509-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ingersoll-Rand 8509-A.

A complete manual for the device Ingersoll-Rand 8509-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ingersoll-Rand 8509-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ingersoll-Rand 8509-A.

A complete Ingersoll-Rand manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ingersoll-Rand 8509-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ingersoll-Rand 8509-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ingersoll-Rand 8509-A, that we can find in the current document
3. Tips how to use the basic functions of the device Ingersoll-Rand 8509-A - which should help us in our first steps of using Ingersoll-Rand 8509-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ingersoll-Rand 8509-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ingersoll-Rand 8509-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ingersoll-Rand 8509-A?

Use the form below

If you did not solve your problem by using a manual Ingersoll-Rand 8509-A, ask a question using the form below. If a user had a similar problem with Ingersoll-Rand 8509-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)