English dropdown-ico

Manual Renesas M16C/20

32 pages 0.13 mb
Download

Go to site of 32

Summary
  • Renesas M16C/20 - page 1

    RENE S A S 1 6 -BIT S IN G LE- C HIP MI C R OCO MP U TE R M1 6C F AMIL Y / M1 6C/ 2 0 S ERIE S M16C/26 Group 16 Rev. 0.90 Revision date: December. 28, 2003 Usage Notes Reference Book www.renesas.com Before using this material, please visit our website to confirm that this is the most current document available. REJ09B0130-0090Z For the most current ...

  • Renesas M16C/20 - page 2

    Keep safety first in your circuit designs! Notes regarding these materials • Renesas T echnology Corporation puts the maximum effort into making semiconductor prod- ucts better and more reliable, but there is always the possibility that trouble may occur with them. T rouble with semiconductors may lead to personal injury , fire or property damage ...

  • Renesas M16C/20 - page 3

    Preface The “Usage Notes Reference Book” is a compilation of usage notes from the Hardware Manual as well as technical news related to this product. ...

  • Renesas M16C/20 - page 4

    A-1 Table of contents 1. Usage Precaution .......................................................................................... 1 1.1 Precautions for Power Control .................................................................................... 1 1.2 Precautions for Protect .................................................................. ...

  • Renesas M16C/20 - page 5

    A-2 1.10 Precautions for Flash Memory V ersion .................................................................. 22 1.10.1 Precautions for Functions to Inhibit Rewriting Flash Memory Rewrite ...................................... 22 1.10.2 Precautions for Stop mode ................................................................................... ...

  • Renesas M16C/20 - page 6

    M16C/26 Group Rev.0.90 2003.12.28 page 1 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1. Usage Precaution 1.1 Precautions for Power Control ____________ 1. When exiting stop mode by hardware reset, set RESET pin to “ L ” until a main clock oscillation is stabilized. 2. Inse ...

  • Renesas M16C/20 - page 7

    M16C/26 Group Rev.0.90 2003.12.28 page 2 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.2 Precautions for Protect Set the PRC2 bit to “ 1 ” (write enabled) and then write to any address, and the PRC2 bit will be cleared to “ 0 ” (write protected). The registers protecte ...

  • Renesas M16C/20 - page 8

    M16C/26 Group Rev.0.90 2003.12.28 page 3 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.3 Precautions for Interrupts 1.3 Precautions for Interrupts 1.3.1 Reading address 00000 16 Do not read the address 00000 16 in a program. When a maskable interrupt request is accepted, the C ...

  • Renesas M16C/20 - page 9

    M16C/26 Group Rev.0.90 2003.12.28 page 4 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.3 Precautions for Interrupts ______ 1.3.5 INT Interrupt 1. Either an “ L ” level of at least t W ( INH ) or an “ H ” level of at least t W ( INL ) width is necessary for the signal _ ...

  • Renesas M16C/20 - page 10

    M16C/26 Group Rev.0.90 2003.12.28 page 5 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.3 Precautions for Interrupts 1.3.6 Rewrite the Interrupt Control Register (1) The interrupt control register for any interrupt should be modified in places where no requests for that interru ...

  • Renesas M16C/20 - page 11

    M16C/26 Group Rev.0.90 2003.12.28 page 6 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.3.7 Watchdog Timer Interrupt Initialize the watchdog timer after the watchdog timer interrupt occurs. 1.3 Precautions for Interrupts ...

  • Renesas M16C/20 - page 12

    M16C/26 Group Rev.0.90 2003.12.28 page 7 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.4 Precautions for DMAC 1.4.1 Write to DMAE Bit in DMiCON Register When both of the conditions below are met, follow the steps below. Conditions • The DMAE bit is set to “ 1 ” again whi ...

  • Renesas M16C/20 - page 13

    M16C/26 Group Rev.0.90 2003.12.28 page 8 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5 Precautions for Timers 1.5.1 Timer A 1.5.1.1 Timer A (Timer Mode) 1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) regist ...

  • Renesas M16C/20 - page 14

    M16C/26 Group Rev.0.90 2003.12.28 page 9 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5.1.2 Timer A (Event Counter Mode) 1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, the UDF reg ...

  • Renesas M16C/20 - page 15

    M16C/26 Group Rev.0.90 2003.12.28 page 10 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5.1.3 Timer A (One-shot Timer Mode) 1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, the ONSF ...

  • Renesas M16C/20 - page 16

    M16C/26 Group Rev.0.90 2003.12.28 page 11 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5.1.4 Timer A (Pulse Width Modulation Mode) 1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, t ...

  • Renesas M16C/20 - page 17

    M16C/26 Group Rev.0.90 2003.12.28 page 12 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5.2 Timer B 1.5.2.1 Timer B (Timer Mode) 1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TBiMR (i = 0 to 2) register and TBi register before ...

  • Renesas M16C/20 - page 18

    M16C/26 Group Rev.0.90 2003.12.28 page 13 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5.2.2 Timer B (Event Counter Mode) 1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TBiMR (i = 0 to 2) register and TBi register before setti ...

  • Renesas M16C/20 - page 19

    M16C/26 Group Rev.0.90 2003.12.28 page 14 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.5 Precautions for Timers 1.5.2.3 Timer B (Pulse Period/pulse Width Measurement Mode) 1. The timer remains idle after reset. Set the mode, count source, etc. using the TBiMR (i = 0 to 2) reg ...

  • Renesas M16C/20 - page 20

    M16C/26 Group Rev.0.90 2003.12.28 page 15 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.6 Precautions for Serial I/O (Clock-synchronous Serial I/O) 1.6 Precautions for Serial I/O (Clock-synchronous Serial I/O) 1.6.1 Transmission/reception _______ ________ 1. With an external c ...

  • Renesas M16C/20 - page 21

    M16C/26 Group Rev.0.90 2003.12.28 page 16 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.6.2 Transmission When an external clock is selected, the conditions must be met while if the UiC0 register ’ s CKPOL bit = “ 0 ” (transmit data output at the falling edge and the rece ...

  • Renesas M16C/20 - page 22

    M16C/26 Group Rev.0.90 2003.12.28 page 17 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.6.3 Reception 1. In operating the clock-synchronous serial I/O, operating a transmitter generates a shift clock. Fix set- tings for transmission even when using the device only for receptio ...

  • Renesas M16C/20 - page 23

    M16C/26 Group Rev.0.90 2003.12.28 page 18 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.7 Precautions for Serial I/O (UART Mode) 1.7 Precautions for Serial I/O (UART Mode) 1.7.1 Special Mode 2 _______ _____ If a low-level signal is applied to the P8 5 /NMI/SD pin when the TB2S ...

  • Renesas M16C/20 - page 24

    M16C/26 Group Rev.0.90 2003.12.28 page 19 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.8 Precautions for A-D Converter 1.8 Precautions for A-D Converter 1. Set ADCON0 (except bit 6), ADCON1 and ADCON2 registers when A-D conversion is stopped (before a trigger occurs). 2. When ...

  • Renesas M16C/20 - page 25

    M16C/26 Group Rev.0.90 2003.12.28 page 20 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.8 Precautions for A-D Converter 8. If the CPU reads the ADi register (i = 0 to 7) at the same time the conversion result is stored in the ADi register after completion of A-D conversion, an ...

  • Renesas M16C/20 - page 26

    M16C/26 Group Rev.0.90 2003.12.28 page 21 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.9 Precautions for Programmable I/O Ports 1.9 Precautions for Programmable I/O Ports _______ _____ 1. If a low-level signal is applied to the P8 5 /NMI/SD pin when the TB2SC register IVPCR1 ...

  • Renesas M16C/20 - page 27

    M16C/26 Group Rev.0.90 2003.12.28 page 22 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.10 Precautions for Flash Memory Version 1.10 Precautions for Flash Memory Version 1.10.1 Precautions for Functions to Inhibit Rewriting Flash Memory Rewrite ID codes are stored in addresses ...

  • Renesas M16C/20 - page 28

    M16C/26 Group Rev.0.90 2003.12.28 page 23 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.10 Precautions for Flash Memory Version 1.10.7 Operation speed Before entering CPU rewrite mode (EW0 or EW1 mode), select 10 MHz or less for CPU clock using the CM0 register ’ s CM06 bit ...

  • Renesas M16C/20 - page 29

    M16C/26 Group Rev.0.90 2003.12.28 page 24 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 1.10 Precautions for Flash Memory Version 1.10.12 DMA transfer In EW1 mode, make sure that no DMA transfers will occur while the FMR0 register ’ s FMR00 bit = 0 (during the auto program or ...

  • Renesas M16C/20 - page 30

    M16C/26 Group Rev.0.90 2003.12.28 page 25 of 28 Under development Preliminary specification Specifications in this manual are tentative and subject to change. 2. Differences Made Depending on Manufactured Time 2.1 RESET Input Ensure that pin RESET must hold valid-low state during powering-up. When using a reset IC, use a CMOS type IC. When using an ...

  • Renesas M16C/20 - page 31

    RENESAS 16-BIT SINGLE-CHIP MICROCOMPUTER USAGE NOTES REFERENCE BOOK M16C/26 Group Rev.0.90 Editioned by Committee of editing of RENESAS Semiconductor Usage Notes Reference Book This book, or parts thereof, may not be reproduced in any form without permission of Renesas Technology Corporation. Copyright © 2003. Renesas Technology Corporation, All r ...

  • Renesas M16C/20 - page 32

    M16C/26 Group Usage Notes Reference Book 2- 6 -2, Ote-machi, Chiyoda-ku, Tokyo, 1 00-0004, Japan ...

Manufacturer Renesas Category Laptop

Documents that we receive from a manufacturer of a Renesas M16C/20 can be divided into several groups. They are, among others:
- Renesas technical drawings
- M16C/20 manuals
- Renesas product data sheets
- information booklets
- or energy labels Renesas M16C/20
All of them are important, but the most important information from the point of view of use of the device are in the user manual Renesas M16C/20.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Renesas M16C/20, service manual, brief instructions and user manuals Renesas M16C/20. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Renesas M16C/20.

Similar manuals

A complete manual for the device Renesas M16C/20, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Renesas M16C/20 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Renesas M16C/20.

A complete Renesas manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Renesas M16C/20 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Renesas M16C/20, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Renesas M16C/20, that we can find in the current document
3. Tips how to use the basic functions of the device Renesas M16C/20 - which should help us in our first steps of using Renesas M16C/20
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Renesas M16C/20
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Renesas M16C/20 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Renesas M16C/20?

Use the form below

If you did not solve your problem by using a manual Renesas M16C/20, ask a question using the form below. If a user had a similar problem with Renesas M16C/20 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)