English dropdown-ico

Manual Simplicity 1721303-01

18 pages 0.55 mb
Download

Go to site of 18

Summary
  • Simplicity 1721303-01 - page 1

    A TT A CHMENT OPERA T OR’S MANU AL Snow Plo w/Dozer Blade Mfg. No. Description 1693754 42” Remote Angling Snow Plow/Dozer Blade Hitch Mfg. No. Description 1693757 Hitch (for Sovereign / 900 / 2800 Series) 1721303-01 Rev 1/2001 TP 100-2374-01-AT-SMA Sno w/Doz er Blade & Hitc h ...

  • Simplicity 1721303-01 - page 2

    1 T able of Contents Maintenance & Normal Care Schedule ..............6 Schedule f or Nor mal Care ...............................6 Lubricate the Dozer Blade ...............................6 Adjustments .........................................................7 Skid Shoe Adjustment .....................................7 Spring T ension ........ ...

  • Simplicity 1721303-01 - page 3

    OPERA TING SAFETY ● Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. ● Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads. Stay alert for hidden hazards or traffic. ● After striking an o ...

  • Simplicity 1721303-01 - page 4

    3 TRA CT OR CONTROLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit. • Practi ...

  • Simplicity 1721303-01 - page 5

    4 Checks Bef ore Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity. 3. Adjust the skid shoes to desired height. See Skid Sh ...

  • Simplicity 1721303-01 - page 6

    5 General Operating Instructions Daily Stora ge 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion. IMPORT ANT NO TE Refer to Tractor Operator’s Manual for ...

  • Simplicity 1721303-01 - page 7

    6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade. Lubricate dozer blade. Every 10 hours or at least once a year. Lubricate Dozer Blade Lubricate the dozer blade as shown in Figure 2. Where an oil can is shown, wipe the area clean, apply a few drops of oil (SAE 30), then wipe up drips or spi ...

  • Simplicity 1721303-01 - page 8

    7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of the shoe assemblies for raising and lowering the blade to various working heights (see Figure 3). When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground. When cleaning smo ...

  • Simplicity 1721303-01 - page 9

    8 Adjustments Figure 6. Adjusting Lift Rod A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Spring Clip Lift Rod Adjustment In the fully raised position the blade should be 6” off the ground. In the fully lowered position, the lift rod should slightly compress the spring creating downward pressure on the blade. NOTE: Always adjust ...

  • Simplicity 1721303-01 - page 10

    9 Initial Setup & Assembly Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Handle, Lower 7 1 CLEVIS 8 1 WASHER, 1/2 9 1 CLIP, Hair Pin 10 3 COTTER PIN 11 1 ROD & PLATE ASMY, Pivot 12 1 DOZER BLADE ASMY, 42” 13 1 SCRAPER BAR 14 6 C ...

  • Simplicity 1721303-01 - page 11

    10 Initial Setup & Assembly 2 1 3 5 6 7 9 15 10 11 9 8 8 8 8 4 4 3 13 12 14 18 17 21 16 20 19 16 18 Ref Qty Description 1 2 STOP, Bar 2 2 SCREW, Taptite, 5/16-18 x 1 3 2 SETSCREWS, 5/16 x 1/2 4 2 SET COLLAR 5 1 ROD GUIDE ASSY. 6 1 SPRING 7 1 ROD, Lift, Electric/Hydraulic 8 5 CLIP, Hairpin 9 2 CLEVIS PIN 10 1 PUSH BAR ASSY, Front 11 1 PIVOT PIN ...

  • Simplicity 1721303-01 - page 12

    11 Initial Setup & Assembly INITIAL SETUP & ASSEMBL Y NOTE: Some of the following setup procedures may already be completed. Assemble Blade 1. Place the blade on a flat surface. 2. Install the bar stops (A, Figure 9) using the two 5/16- 18 x 1 taptite screws (B). 3. See Figure 10. Insert threaded end of eyebolt (A) through lug on blade, and ...

  • Simplicity 1721303-01 - page 13

    12 Initial Setup & Assembly Install Blade 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. Raise rear of push bar so its arms fit between lugs of hitch (A, Figure 12) just behind front axle. Use two clevis pins (B) and spring clips (C) to secure push bar to ...

  • Simplicity 1721303-01 - page 14

    13 Initial Setup & Assembly Figure 13. Control Rod Support A. Angling Support D. 5/16 Flatwasher B. Eyebolt & Locknut E. Flange Locknuts C. 5/16-18 x 1-1/2 Capscrews Install Angling Control Rod NOTE: If installing the dozer attachment on a unit equipped with a snowcab, replace the control rod sup- port (A, Figure 13) with the hanging suppor ...

  • Simplicity 1721303-01 - page 15

    14 Attaching & Removing REMO V AL & INST ALLA TION Removing & Attac hing Dozer Blade 1. Lower the blade. 2. Remove the hair pin clip and washer (D, Figure 15) securing the angling control rod to the clevis. Disconnect the angling control rod. 3. Remove the angling control rod from the support arm (A). 4. Remove the pivot pin (C) connect ...

  • Simplicity 1721303-01 - page 16

    15 T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 ...

  • Simplicity 1721303-01 - page 17

    16 NO TES ...

  • Simplicity 1721303-01 - page 18

    MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2000 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...

Manufacturer Simplicity Category Lawn Mower Accessory

Documents that we receive from a manufacturer of a Simplicity 1721303-01 can be divided into several groups. They are, among others:
- Simplicity technical drawings
- 1721303-01 manuals
- Simplicity product data sheets
- information booklets
- or energy labels Simplicity 1721303-01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Simplicity 1721303-01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Simplicity 1721303-01, service manual, brief instructions and user manuals Simplicity 1721303-01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Simplicity 1721303-01.

Similar manuals

A complete manual for the device Simplicity 1721303-01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Simplicity 1721303-01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Simplicity 1721303-01.

A complete Simplicity manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Simplicity 1721303-01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Simplicity 1721303-01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Simplicity 1721303-01, that we can find in the current document
3. Tips how to use the basic functions of the device Simplicity 1721303-01 - which should help us in our first steps of using Simplicity 1721303-01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Simplicity 1721303-01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Simplicity 1721303-01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Simplicity 1721303-01?

Use the form below

If you did not solve your problem by using a manual Simplicity 1721303-01, ask a question using the form below. If a user had a similar problem with Simplicity 1721303-01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)