Manual Sears 8MPL100F20B1

56 pages 3.83 mb
Download

Go to site of 56

Summary
  • Sears 8MPL100F20B1 - page 1

    80+ Single Stage Category I Furnace N8MPN & N8MPL *8MPN & *8MPL * Denotes Brands (C, H, T) See section 5 for Category [ definition. SAFETY REQUIREMENTS Recognize safety information. This is the safety-alert symbolZl._. When you see this symbol on the furnace and in instruction manuals be alert to the potential for personal injury. Understan ...

  • Sears 8MPL100F20B1 - page 2

    START-UP CHECK SHEET (Keep this page for future reference) Recommended, but not required, Dealer Name: Address: City, State(Province), Zip or Postal Code: Business Card Here Phone: Owner Name: Address: City, State(Province), Zip or Postal Code: Model Number: Serial Number: Natural: _1 LP: _1 Type of Gas: Blower Motor H. P,: Supply Voltage: Limit Op ...

  • Sears 8MPL100F20B1 - page 3

    1. Safe Installation Requirements FIRE, EXPLOSION, AND ASPHIXIATION HAZARD Improper adjustment, alteration, service, maintance or installation could cause death, personal injury, and/or property damage. Installation or repairs made by unqualified persons could result in hazards to you and others. Installation MUST conform with local codes or, in th ...

  • Sears 8MPL100F20B1 - page 4

    Frozen Water Pipe Hazard If your furnace remains off for an extended time, the pipes in your home could freeze and burst, resulting in serious water damage. FROZEN AND BURST WATER PIPE HAZARD Failure to protect against the risk of freezing could result in property damage. Do not leave your home unattended for long periods during freezing weather wi ...

  • Sears 8MPL100F20B1 - page 5

    The air temperature rise is within the rated rise range on the furnace rating plate, and the firing rate has been setto the rating plate value. The filters used to clean the circulating air during the construction process must be either changed or thor- oughly cleaned prior to occupancy. • The furnace, ductwork and filters are cleaned as neces- s ...

  • Sears 8MPL100F20B1 - page 6

    Dimensions and Clearances (*8MPN/L Models) TOP LEFT SIDE • Plugged starting I hole to cut side 131/4 _¢t opening 21814 17/8 / 26518 5113 5f__ _ _1 -- 3314 7/8 1 47/ 11/2 _E "24"Min. --A_ -- B -- 38 FRONT ® MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS FOR ALL UNITS REAR 0 FRONT (combustion air openings 3" in furnace and structure) ...

  • Sears 8MPL100F20B1 - page 7

    iiiiiiiiiiiiiiiii_!!!!!!!!:!i:iil ¸;i ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii¸i ¸ii ¸ii ¸ii ¸iiiiliiiiii;;;iiiiiiii;i;il;i;i;i;iiii_ilili;i;i;i;;i;i;il;i;iiiii ¸i;iiiii!!! i!i!i!i!i!i!i!i!i!i!i! i i i i i ii i ! i ! i!! i!i!!i!iiii! iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i i i i i T p,ca, Up.ow ,nsta.at,on SUPPLY AIR RETURN N GAS SUPPLY 25-23-17 ...

  • Sears 8MPL100F20B1 - page 8

    3. New labels for rightside-up application on outside ofblower compartment door may be purchased in a kit from your distrib- utor tocover upside-down labels. Downflow Venting: The combustion venter MUST be rotated to vent out the side for all downflow installations, (see Figure 5). Bot- tom venting is not permitted. See"Side venting" for ...

  • Sears 8MPL100F20B1 - page 9

    7. Tighten the three (3) or four (4) screws that secure the venter assembly to the collector box. Do tighten screws enough to compress venter gasket. 8. Replace power leads to venter motor and reconnect hose to pressure switch. NOTE: Unused open vent hole must be covered. A Vent Cover is supplied with Vent Pipe Shield Kit NAHAOO2VC. A 55/16" d ...

  • Sears 8MPL100F20B1 - page 10

    Outside Air (This is ONLY a guide. SubJect to codes of country having jurisdiction.) This installation NOT approved in Canada Gas Vent , Gable V_/) (1) Soffit Vent Inlet Air (1) Minimum One Inlet and One Outlet Air Supply is Required May be in and Combination Shown Inlet Air Opening Must be Within12"(300mm) of floor Outlet Air Opening Must be ...

  • Sears 8MPL100F20B1 - page 11

    The Standard Method may be used, if the space has no less vol- ume than 50 cubic feet per 1,000 BTUH of the maximum input rat- ings for all gas appliances installed in the space. The standard method permits indoor air to be used for combustion and ventila- tion air. The Known Air Infiltration Rate Method shall be used if the in- filtration rate is ...

  • Sears 8MPL100F20B1 - page 12

    Z223.1-2002/N FPA 54-2002; and/or Section 7 and Appendix C of the CSA B149.1-05, National Standard ofCanada, Natural Gas and Propane Installation Code; the local building codes; furnace and vent manufacturer's instructions. NOTE: The following instructions comply with the ANSI Z223.1/NFPA 54 National Fuel Gas Code and CSA B149.1 Natu- ral Gas ...

  • Sears 8MPL100F20B1 - page 13

    13.2 or a listed, metal lining system. (See Section 7 Masonry Chimney Venting of these instructions.) Listed, corrugated metallic chimney liner systems in masonry chimneys shall be sized by using NFGC tables per 13.1.7 for dedi- cated venting and per 13.2.19 for common venting with the maxi- mum capacity reduced by 20% (0.80 X maximum capacity) and ...

  • Sears 8MPL100F20B1 - page 14

    iiiiiiiiiiiiiiiiiiiiiiiiiiiii i i! ii ii ! i ! !i ! ii i i i i i i i i i i i Item A B C 9 E F G H I J K L M N 0 Other than Direct Vent Termination Clearance IVIVENTTERMINAL AIRSUPPLVINLET Clearance Descriptions Canadian Installation (1) Clearance above grade, veranda, porch, deck, balcony, or 12" (30cm) # anticipated snow level Clearance to a ...

  • Sears 8MPL100F20B1 - page 15

    7. Masonry Chimney Venting Chimney Inspection All masonry chimney construction must conform to Standard ANSI/NFPA 211-2003 and to any state or local codes applicable. The chimney must be in good condition and a complete chimney inspection must be conducted prior to furnace installation. If the in- spection reveals damage or abnormal conditions, mak ...

  • Sears 8MPL100F20B1 - page 16

    CHIMNEY INSPECTION CHART For additionalrequirementsrefer tothe National Fuel GasCodeNFPA541ANSI Z223.1-2002andANSIINFPA211-2003 Chimneys, Fireplaces, Vents,and Solid Fuel Burnin 9 Appliances in the U.S.A. or to the CanadianInstallation Code CSA B149.1-05 in Canada. Rebuild I Reline .._ Remove mortar 1_ andtile debris? tile m.isalignment, Yes mg sec ...

  • Sears 8MPL100F20B1 - page 17

    Exterior Masonry Chimney, FAN+NAT Installations with Type-B Double-Wall Vent Connectors VENT HEIGHT (FT) 6 8 10 15 20 30 © NFPA & AGA Table A- Combined Appliance Maximum Input Rating in Thousands of Btu per Hr INTERNAL AREA OF CHIMNEY (SQ IN,) 12 19 28 38 74 119 178 257 80 130 193 279 84 138 207 299 NR 152 233 334 NR NR 250 368 NR NR NR 404 Ta ...

  • Sears 8MPL100F20B1 - page 18

    Vent dampers onany appliance connected to the common vent can cause condensation and corrosion in the venting system. Do not use vent dampers on appliances common vented with this fur- nace. 8. Gas Supply and Piping CARBON MONOXIDE POISONING, FIRE AND EXPLOSION HAZARD. Gas Piping Requirements NOTE: The gas supply line must be installed by a qualift ...

  • Sears 8MPL100F20B1 - page 19

    5, 6, 7. Use ground joint unions and install a drip leg no less than 3" long to trap dirt and moisture before it can enter gas control valve inside furnace. Provide a 1/8" NPT plugged tapping for test gauge connection immediately up stream of gas supply connection to furnace. Use two pipe wrenches when making connections to prevent furnac ...

  • Sears 8MPL100F20B1 - page 20

    Typical Gas Piping ('aMP) 25-25-02 Piping with Street Elbows 1. Screw one elbow onto gas valve with the outlet facing away from the furnace. 2. Screw second elbow onto first elbow tight enough to be leak proof. An additional 1/4 turn will be required at the end of step 2. See Figure 17 and Figure 18. Gas Valve with Elbows ('8MP) 25-25-03 ...

  • Sears 8MPL100F20B1 - page 21

    9. Electrical Wiring ELECTRICALSHOCK HAZARD. Failure to follow safety warnings exactly could result in death or personal injury. Turn OFF electrical power at fuse box or service panel before making any electrical connections and ensure a proper ground connection is made before connecting line voltage. Power Supply Wiring The furnace MUST be electri ...

  • Sears 8MPL100F20B1 - page 22

    Electrical Connections 115V. 60Hz. Gr_nd Thermostat I ! , I L ] _ _ Low Voltage Terminal Board NOTE: 115 VAC/6OHz/single-phase Operating voltage range*: 127 VAC max, 104 VAC min. * Permissible limits of voltage at which unit will operate satisfactorily Furnace Control The furnace control is preset at the factory with ON delay of 30 sec- onds in the ...

  • Sears 8MPL100F20B1 - page 23

    area. It is often advisable to route the return air ducts under the Filters are not supplied with these furnaces, but can be purchased floor or through the attic, from your distributor. • Refer to furnace Technical Support Manual (Blower Data) for air flow information. • Size ductwork to handle air flow for heating (and air condition- ing if so ...

  • Sears 8MPL100F20B1 - page 24

    Optional Duct Standoff Filter 20 x 25 Optional Filter Rack 25-23-05-4 Optional Filter Rack Installation: Side Return Center the filter rack on the side panel, flush with the bottom edge of the furnace. Mark the fastening holes. Drill the fastening holes in the side panel and fasten the filter rack in place with sheet metal screws. See Figure 23 and ...

  • Sears 8MPL100F20B1 - page 25

    11. Ductwork and Filter (Downflow) CARBON MONOXIDE POISONING HAZARD. Failure to properly seal duct could result in death or personal injury. Do NOT draw return air from inside a closet or utility room where furnace is located. Return air duct MUST be sealed to furnace casing. FIRE HAZARD. Failure to install furnace on noncombustible subbase could r ...

  • Sears 8MPL100F20B1 - page 26

    Exploded View of Sub-Base for Furnace ONLY I tr Combustible Floor Base ¸i!i i¸i Subbase Furnac_ Insulation Wood Screw Setting the Base / _. % _W_°°d Fl°°r Sub-base for Combustible Floors - Downflow Coil Adapter Box The subbase for combustible floors is required when a downflow furnace, used with a downflowcoilbox, is set on combustible floori ...

  • Sears 8MPL100F20B1 - page 27

    Duct Design and Duct Installation Requirements See Section 10. Internal Filter in Top Return Installation When instal ling top-mounted filter inside the furnace, install the fil- ter clips on the edge of the top duct opening with the wider end of the clips toward the blower as shown in Figure 32. Clips may be obtained from your distributor or fabri ...

  • Sears 8MPL100F20B1 - page 28

    wise to decrease manifold pressure and clockwise to Operation Above 2000' Altitude increase pressure. NOTE: Adjustment screw cover MUST be replaced on gas control valve before reading manifold pressure and operating furnace. 4, 5. Set manifold pressure to value shown in Table 6 or Table 7. When the manifold pressure is properly set, replace th ...

  • Sears 8MPL100F20B1 - page 29

    MANIFOLD PRESSUREAND ORIFICE SIZE FOR HIGH ALTITUDE APPLICATIONS NATURAL GAS MANIFOLD PRESSURE (" w.c.) .............................................................. MEAN ELEVATION FEET ABOVE SEA LEVEL HEATING 0 to 2001 to 3001 to 4001 to 5001 to 6001 to 7001 to VALUE 2000 3000 4000 5000 6000 7000 8000 at ALTITUDE Orifice Manifold Orifice Man ...

  • Sears 8MPL100F20B1 - page 30

    9. After reassembling, turn gas on and check all joints for gas leaks using a soapy solution. All leaks must be repaired im- mediately. Clearances Measure from face of orifice to the batck side of the manifold, 29.3 +_11"5 mm "k,,..k--..,.,.r_ j LP Conversion I An accessory kit shall be used to convert to propane gas use, see the furnace ...

  • Sears 8MPL100F20B1 - page 31

    Ignitor Location NOTE: Flame sensor has a different orientation in all 050 models. Air Temperature Rise Check REDUCED FURNACE LIFE HAZARD Failure to properly set the air temperature rise may result in reduced furnace life. Use ONLY the blower motor speed taps marked "Y" for YES for setting air temperature rise. Blower Motor Speed Taps for ...

  • Sears 8MPL100F20B1 - page 32

    ous-fan option. This connection is intended for the low speed mo- tor tap, and has a lower contact rating (8 amps) than the heat and cool taps. When the low speed blower lead is connected to this terminal, this will provide low speed blower operation whenever the other two speeds (Heat or Cool) are not energized. EAC not powered in this mode. Thoro ...

  • Sears 8MPL100F20B1 - page 33

    14. Sequence of Operation & Diagnostics The following is the normal operating sequence. Cooling (¥) Request: 24VAC signals applied to Y & G terminals of FCB (furnace control board) • Cool motor speed is energized after 5 second Cool Fan On Delay time. Y & G signals removed from FCB • Cool motor speed is de-energized after 90 second ...

  • Sears 8MPL100F20B1 - page 34

    Heating Request with Gas Shut Off: 24 VAC signal applied to W terminal of FCB. The FCB will attempt 4 cycles for ignition then go to soft lockout for 3 hours then try for ignition again as long as the heat call remains. Power reset will clear lockout. • Inducer motor turns on • Following a 15 second prepurge delay, the igniter begins warm up. ? ...

  • Sears 8MPL100F20B1 - page 35

    II I I ® I Save This Manual For Future Reference N8MPN050B12B1 N8MPN075B12B1 N8MPN075F16B1 N8MPN100F14B1 N8MPN100F20B1 N8MPN100J22B1 N8MPN125J20B1 N8MPN125J22B1 *8MPN050B12B1 *8MPN075B12B1 *8MPN075F16B1 *8MPN 100F14B1 *8MPN100F20B1 *8MPN100J20B1 *8MPN125J20B1 *8MPN 150J20B1 * Denotes Brand Models N8MPL050B12B1 N8MPL075B12B1 N8MPL075F16B1 N8MPL100F ...

  • Sears 8MPL100F20B1 - page 36

    Manufacturers Number (Mfr No -See RatingPlate) ALL Models (N8MPN) Specifications N8MPN N8MPN N8MPN N8MPN N8MPN N8MPN N8MPN N8MPN 050B12 075B12 075F16 100F14 100F20 100J22 125J20 125J22 General Input (Btuh) 50,000 75,000 75,000 100,000 100,000 100,000 125,000 125,000 Output (Btuh) 40,000 60,000 60,000 80,000 80,000 80,000 100,000 100,000 Temp. Rise ...

  • Sears 8MPL100F20B1 - page 37

    Manufacturers Number (Mfr No -See RatingPlate) ALL Models (N8MPL) Specifications N8MPL N8MPL N8MPL N8MPL N8MPL N8MPL N8MPL O5OB12 O75B12 O75F16 1OOF20 1OOJ22 125J20 125J22 General Input (Btuh) 50,000 75,000 75,000 100,000 100,000 125,000 125,000 Output (Btuh) 40,000 60,000 60,000 80,000 80,000 100,000 100,000 Temp. Rise (F) 35-65 35-65 25-55 35-65 ...

  • Sears 8MPL100F20B1 - page 38

    Manufacturers Number (Mfr No -See RatingPlate) ALL Models (*8MPN) Specifications *8MPN *8MPN *8MPN *8MPN *8MPN *8MPN *8MPN *8MPN 050B12 075B12 075F16 100F14 100F20 100J20 125J20 150J20 General Input (Btuh) 50,000 75,000 75,000 100,000 100,000 100,000 125,000 150,000 Output (Btuh) 40,000 60,000 60,000 81,000 81,000 81,000 101,000 121,000 Temp. Rise ...

  • Sears 8MPL100F20B1 - page 39

    Manufacturers Number (Mfr No -See RatingPlate) ALL Models (*8MPL) Specifications *8MPL *8MPL *8MPL *8MPL *8MPL *8MPL 050B12 075B12 075F16 100F20 100J20 125J20 General Input (Btuh) 50,000 75,000 75,000 100,000 100,000 125,000 Output (Btuh) 40,000 60,000 60,000 81,000 81,000 101,000 Temp. Rise (F) 35-65 30-60 30-60 35-65 35-65 35-65 Electrical (Volts ...

  • Sears 8MPL100F20B1 - page 40

    15. Circulation Air Blower Data (CFM) 1 N8MPN/L050B12 & *8MPN/L050B12 (1) • Denotes Brand 1N8MPN/L100F20 & *8MPN/L100F20 (2)(4) • Denotes Brand Air Delivery in Cubic Feet per Minute (C,F.M.) = (Furnace Rated @0.5" WC ESP) O TAP LOW MED L MED H HIGH _ ,10 472 704 1167 1387 ,9 _o ,30 365 638 1102 1288 _ .50 290 572 1035 1194 E _ .70 ...

  • Sears 8MPL100F20B1 - page 41

    Circulation Air Blower Data Continued • N8MPN/L125J22 (2)(6) Air Delivery in Cubic Feet per Minute (C.F.M.) = (Furnace Rated @0.5" WC ESP) O TAP LOW MED L MED H HIGH _ ,10 1901 2121 2362 2463 ,£ _o ,30 1833 2033 2244 2385 ,50 1745 1936 2100 2217 E _ .70 1624 1773 1894 2033 .90 1442 1569 1714 1821 1.00 1329 1455 1583 1685 _ISMPN150J20 (2)(7) ...

  • Sears 8MPL100F20B1 - page 42

    + + WARNING: ELECTRICAL SHOCK HAZARD It' CONNECTION DIAGRAM DISCONNECT BEFORE SERVICING LADDER DIAGRAM zoo _. m _OO ROLLOUT SWITCH +TO2 > +4 0 0 TO 115VAC FIELD DISCONNECT INSERIES DEPENDING LP PRESSURE . . COPPER CONDUCTORS C) rr ONMODEL MAIN LIMIT BVSS SWTCH CAPACITOR ONLY J[ HOT NOTE #2 • */_7 EQUIPMENT GROUND Oo O _i R __R 2 (WHEN USE ...

  • Sears 8MPL100F20B1 - page 43

    Parts for N8MPN/L 16 17 u AA S 2 H 6 F E 3 4 25-25-09 441 01 2613 02 [_ ...

  • Sears 8MPL100F20B1 - page 44

    [ Replacement Parts - N8MPN (Natural Gas) I Models - N8MPNO50B12B1, NSMPNO75B12B1, N8MPNO75F16B1, NSMPN100F14B1, N8MPNIOOF2OB1, N8MPNlOOJ22B1, NSMPN125J20B1, NSMPN125J22B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. NSMPN Key Description Part I I No. Functional Parts Number 050B 075B 075F ...

  • Sears 8MPL100F20B1 - page 45

    [ Replacement Parts - N8MPN (Natural Gas) Models - N8MPN050B12B1, NSMPN075B12B1, N8MPN075F16B1, NSMPN100F14B1, N8MPN100F20B1, N8MPN100J22B1, N8MPN125J20B1, NSMPN125J22B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. N8MPN Key Description Part I I I No. Non- Functional Parts Number 050B 075B ...

  • Sears 8MPL100F20B1 - page 46

    [ Replacement Parts - N8MPN (Natural Gas) Models - N8MPNO50B12B1, NSMPNO75B12B1, N8MPNO75F16B1, NSMPN100F14B1, N8MPNIOOF2OB1, N8MPNlOOJ22B1, N8MPN125J20B1, NSMPN125J22B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. N8MPN Key Description Part I I I No. Non- Functional Parts Number 050B 075B ...

  • Sears 8MPL100F20B1 - page 47

    [ Replacement Parts - N8MPL (Natural Gas) I Models - N8MPLO50B12B1, N8MPLO75B12B1, N8MPLO75F16B1, N8MPLIOOF2OB1, N8MPL100J22B1, NSMPL125J20B1, N8MPL125J22B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. Key Description Part N8MPL No. Functional Number 075F16B1 100F20B1 100J22B1 125J20B1 125J ...

  • Sears 8MPL100F20B1 - page 48

    [ Replacement Parts - N8MPL (Natural Gas) I Models - N8MPLO50B12B1, NSMPLO75B12B1, N8MPLO75F16B1, NSMPLIOOF2OB1, N8MPLIOOJ2OB1, N8MPL100J22B1, N8MPL125J20B1, NSMPL125J22B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. Key Part No. Number 075B lOOJ 125J 125J 12B1 22B1 20B1 22B1 A 1 Descriptio ...

  • Sears 8MPL100F20B1 - page 49

    [ Replacement Parts - N8MPL (Natural Gas) I Models - N8MPLO50B12B1, NSMPLO75B12B1, N8MPLO75F16B1, NSMPLIOOF2OB1, N8MPLIOOJ2OB1, N8MPL100J22B1, N8MPL125J20B1, NSMPL125J22B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. NSMPL Key Description Part I I No. Functional Number 075B 075F IOOF lOOJ 1 ...

  • Sears 8MPL100F20B1 - page 50

    Parts for *8MPN/L 18 BB x 17 Z 16 U 11 15 AA T 16 CC 1 G F E 25-25-09a 441 01 2613 02 ...

  • Sears 8MPL100F20B1 - page 51

    I Replacement Parts - *8MPN (Natural Gas) Models - *SMPNO50B12B1, *SMPNO75B12B1, *8MPNO75F16B1, *SMPN100F14B1, *SMPNIOOF2OB1, *8MPNIOOJ2OB1, *SMPN125J20B1, *8MPN150J20B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. Key Description No, Functional Heat Exchanger 2 Switch, Pressure 3 Wheel, Bl ...

  • Sears 8MPL100F20B1 - page 52

    I Replacement Parts - *8MPN (Natural Gas) Models - *8MPNO50B12B1, *8MPNO75B12B1, *8MPNO75F16B1, *8MPN100F14B1, *8MPNIOOF2OB1, *8MPNIOOJ2OB1, *8MPN125J20B1, *8MPN150J2OB1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. Key Description No, Functional Panel, Top B Box, Junction C Cover, Junction ...

  • Sears 8MPL100F20B1 - page 53

    | I Replacement Parts - *8MPN (Natural Gas) Models - *SMPN050B12B1, *SMPN075B12B1, *8MPN075F16B1, *SMPN100F14B1, *SMPN100F20B1, *8MPN100J20B1, *SMPN125J20B1, *8MPN150J20B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. Key Description Part No, Functional Number 075B 075F 100J "125J 150J ...

  • Sears 8MPL100F20B1 - page 54

    I Replacement Parts - *8MPL (Natural Gas) I Models - *8MPLO5OB12B1, *8MPLO75B12B1, *8MPLO75F16B1, *SMPLIOOF2OB1, *8MPLIOOJ 20B1, *8MPL125J20B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. *8MPL Key Description Part No. Functional Number 050B 075B 075F IOOF lOOJ 125J 12B1 12B1 16B1 20B1 20B1 ...

  • Sears 8MPL100F20B1 - page 55

    I Replacement Parts - *8MPL (Natural Gas) I Models - *8MPL050B12B1, *8MPL075B12B1, *8MPL075F16B1, *SMPL100F20B1, *8MPL100J 20B1, *8MPL125J20B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. Key Description Part No, Functional Number 050B *075B 12B1 12B1 A Panel, Top 1 1 B Box, Junction C Cove ...

  • Sears 8MPL100F20B1 - page 56

    | I Replacement Parts - 8MPL (Natural Gas) I Models - '8MPLO5OB12B1, '8MPLO75B12B1, "8MPLO75F16B1, "SMPLIOOF2OB1, '8MPLIOOJ 20B1, "8MPL125J20B1 Replacement part supplied will be current active part. For parts not listed, consult place of purchase. *8MPL Key Description Part No. Functional Number 050B _075B 100F lOOJ 12 ...

Manufacturer Sears Category Furnace

Documents that we receive from a manufacturer of a Sears 8MPL100F20B1 can be divided into several groups. They are, among others:
- Sears technical drawings
- 8MPL100F20B1 manuals
- Sears product data sheets
- information booklets
- or energy labels Sears 8MPL100F20B1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sears 8MPL100F20B1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sears 8MPL100F20B1, service manual, brief instructions and user manuals Sears 8MPL100F20B1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sears 8MPL100F20B1.

Similar manuals

A complete manual for the device Sears 8MPL100F20B1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sears 8MPL100F20B1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sears 8MPL100F20B1.

A complete Sears manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sears 8MPL100F20B1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sears 8MPL100F20B1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sears 8MPL100F20B1, that we can find in the current document
3. Tips how to use the basic functions of the device Sears 8MPL100F20B1 - which should help us in our first steps of using Sears 8MPL100F20B1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sears 8MPL100F20B1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sears 8MPL100F20B1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sears 8MPL100F20B1?

Use the form below

If you did not solve your problem by using a manual Sears 8MPL100F20B1, ask a question using the form below. If a user had a similar problem with Sears 8MPL100F20B1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)