Manual Vulcan-Hart 7016A1 ML-104495

16 pages 0.19 mb
Download

Go to site of 16

Summary
  • Vulcan-Hart 7016A1 ML-104495 - page 1

    7000 SERIES GAS OVENS MODEL 7018A1 ML-104491 7088A1 ML-104492 7888A1 ML-104493 7086A1 ML-104494 7016A1 ML-104495 7066A1 ML-104496 7019A1 ML-104497 7099A1 ML-104498 7999A1 ML-104499 7096A1 ML-104500 7098A1 ML-104501 7988A1 ML-104502 7998A1 ML-104503 MODEL 7019A1 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 3 ...

  • Vulcan-Hart 7016A1 ML-104495 - page 2

    — 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OB ...

  • Vulcan-Hart 7016A1 ML-104495 - page 3

    — 3 — T ABLE OF CONTENTS MODEL 7000 SERIES OVEN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Bake Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Roast Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Vulcan-Hart 7016A1 ML-104495 - page 4

    — 4 — MODEL 7000 SERIES BAKE OVEN CONFIGURATIONS 7086A1 7016A1 7066A1 7018A1 7088A1 7888A1 ...

  • Vulcan-Hart 7016A1 ML-104495 - page 5

    — 5 — MODEL 7000 SERIES ROAST OVEN CONFIGURATIONS 7019A1 7099A1 Model 7999A1 not shown. MODEL 7000 SERIES COMBINATION BAKE & ROAST OVEN CONFIGURATIONS 7096A1 7098A1 7988A1 Model 7998A1 not shown. ...

  • Vulcan-Hart 7016A1 ML-104495 - page 6

    — 6 — Installation, Operation and Care of VULCAN 7000 SERIES BAKE AND ROAST OVEN KEEP THESE INSTRUCTIONS GENERAL The manufacturer suggests that you thoroughly read this entire manual and carefully follow all of the instructions provided. Your Vulcan 7000 Series Bake and Roast Oven is produced with quality workmanship and material. Proper instal ...

  • Vulcan-Hart 7016A1 ML-104495 - page 7

    — 7 — INST ALLA TION UNPACKING Immediately after unpacking, check for possible shipping damage. If the oven is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. There may be a large label located on the front of the oven which reads, "Remove this label before operation." To remove lab ...

  • Vulcan-Hart 7016A1 ML-104495 - page 8

    — 8 — ASSEMBLY Legs If oven is to be mounted on legs, assemble legs to the oven. Tip oven back and install two front legs with bolts through bottom of oven base frame. Tip oven forward, block up back and install rear legs. Remove shipping harnesses from the burner area. If oven is to be placed on legs, do not remove burner shipping harness unti ...

  • Vulcan-Hart 7016A1 ML-104495 - page 9

    — 9 — These ovens can be mounted interchangeably starting with the largest section on the bottom. The factory shipping tags will be marked accordingly. For the purpose of stacking positions, the suffix letter at the end of the model number is your guide: T — Top Section M — Middle Section B — Bottom Section If you do not have one of the a ...

  • Vulcan-Hart 7016A1 ML-104495 - page 10

    — 10 — GAS CONNECTIONS All gas supply connections and any pipe joint compound used must be resistant to the action of propane gases. The oven is equipped for a 3 / 4 " gas pipe connection. Pipe gas supply to the oven. Make sure the pipes are clean and free of obstructions, dirt and piping compound. When connecting the gas supply to the ove ...

  • Vulcan-Hart 7016A1 ML-104495 - page 11

    — 11 — ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: APPLIANCES EQUIPPED WITH A FLEXIBLE ELECTRIC SUPPLY CORD ARE PROVIDED WITH A THREE-PRONG GROUNDING PLUG. IT IS IMPERATIVE THAT THIS PLUG BE CONNECTED I ...

  • Vulcan-Hart 7016A1 ML-104495 - page 12

    — 12 — OPERA TION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE OVEN. CONTROLS (Fig. 4) Burner Valve — when opened, allows gas to flow to the oven burner. To open valve, turn knob counterclockwise; to close valve, turn knob clockwise. Ignition Button — used to reset the oven pilot. To operate, p ...

  • Vulcan-Hart 7016A1 ML-104495 - page 13

    — 13 — LIGHTING AND SHUTTING DOWN PILOT 1. Turn on main gas supply. 2. Turn burner valve ON and purge air from line. Turn burner valve OFF. 3. Wait 5 minutes, then turn burner valve ON and depress ignition button. Using a lit taper, ignite oven pilot (Fig. 5). Continue to hold button in for approximately 30 seconds, then release. 4. If pilot go ...

  • Vulcan-Hart 7016A1 ML-104495 - page 14

    — 14 — PREHEATING Set thermostat knob to desired temperature and allow oven to preheat for approximately 15 minutes before loading. LOADING OVEN 1. When using 2- or 4-deck sections that have one control for two compartments, load both compartments simultaneously. If a quantity sufficient for only one compartment is to be baked, load only the co ...

  • Vulcan-Hart 7016A1 ML-104495 - page 15

    — 15 — CLEANING WARNING: TURN OVEN OFF AND UNPLUG THE ELECTRICAL CORD (IF APPLICABLE) BEFORE CLEANING. Clean interior and exterior of oven daily with warm water and detergent solution. Rinse thoroughly and wipe dry with a soft clean cloth. Oven Inspection Window (Optional) The oven inspection window may be cleaned with an oven cleaner compound ...

  • Vulcan-Hart 7016A1 ML-104495 - page 16

    — 16 — MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE OVEN. REPLACING OPTIONAL LAMPS WARNING: TURN OVEN OFF AND UNPLUG ELECTRICAL CORD BEFORE REPLACING LAMPS. Lamps are located in the top of the oven, centered at the back. 1. Remove (4) 10-24 sheet metal screws, remove glass, and unscrew ...

Manufacturer Vulcan-Hart Category Oven

Documents that we receive from a manufacturer of a Vulcan-Hart 7016A1 ML-104495 can be divided into several groups. They are, among others:
- Vulcan-Hart technical drawings
- 7016A1 ML-104495 manuals
- Vulcan-Hart product data sheets
- information booklets
- or energy labels Vulcan-Hart 7016A1 ML-104495
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vulcan-Hart 7016A1 ML-104495.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vulcan-Hart 7016A1 ML-104495, service manual, brief instructions and user manuals Vulcan-Hart 7016A1 ML-104495. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vulcan-Hart 7016A1 ML-104495.

A complete manual for the device Vulcan-Hart 7016A1 ML-104495, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vulcan-Hart 7016A1 ML-104495 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vulcan-Hart 7016A1 ML-104495.

A complete Vulcan-Hart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vulcan-Hart 7016A1 ML-104495 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vulcan-Hart 7016A1 ML-104495, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vulcan-Hart 7016A1 ML-104495, that we can find in the current document
3. Tips how to use the basic functions of the device Vulcan-Hart 7016A1 ML-104495 - which should help us in our first steps of using Vulcan-Hart 7016A1 ML-104495
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vulcan-Hart 7016A1 ML-104495
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vulcan-Hart 7016A1 ML-104495 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vulcan-Hart 7016A1 ML-104495?

Use the form below

If you did not solve your problem by using a manual Vulcan-Hart 7016A1 ML-104495, ask a question using the form below. If a user had a similar problem with Vulcan-Hart 7016A1 ML-104495 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)