English dropdown-ico

Manual Vulcan-Hart GCT48

16 pages 0.18 mb
Download

Go to site of 16

Summary
  • Vulcan-Hart GCT48 - page 1

    INSTALLATION & OPERATION MANUAL VULCAN ENDURANCE Series Gas Hot Plates MODELS: GCT12 GCT2 4 GCT36 GCT4 8 GCT60 GCT7 2 www.vulcanhart.com ITW Food Equipment Group, LLC 10405 Westlake Drive Charlotte, NC 28273 RETAIN THIS MANUAL FOR FUTURE USE FORM F38202 Rev . A (07-08) ...

  • Vulcan-Hart GCT48 - page 2

    IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSO NNEL QUALIFIED TO INSTALL GA S EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE IN STRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED F ...

  • Vulcan-Hart GCT48 - page 3

    - 3 - INSTALLATION, OPERATION AND CARE OF VULCAN ENDURANCE SERIES GAS HOT PLATES PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Vulcan hot plates are produced with quality workmanship and material. These hot plates are designed with efficiency in cooking performance, sanitation, and ea se of cleaning in mind. Proper insta llation, usage and mainten ...

  • Vulcan-Hart GCT48 - page 4

    - 4 - The hot plate(s) must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearance for air openings into the hot plate(s) must be provided. Make sure there is an adequate supply of air in the room to allow for combustion of the gas at th e burners. INSTALLATION CODES AND STANDARDS Your Vulcan hot ...

  • Vulcan-Hart GCT48 - page 5

    LEVELING To level the hot plate, place a carpenter's level on the hot plate and check leveling of the unit side to side and front to rear. Achieve leveling by turning each foot section of the unit's leg as needed. Turning the foot in a counter clockwise directi on will increase height and clockwis e will decrease. GAS PRESSURE REGULATOR A ...

  • Vulcan-Hart GCT48 - page 6

    gases be ventilated to the outside of the building through a ventilation system installed by qualified personnel. From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18" (457 mm) must be maintained. Information on the construction and installation of ventilating hoods may be obtained from the stan ...

  • Vulcan-Hart GCT48 - page 7

    - 7 - Vulcan equipment is strongly constructed and is designed to give you long, satisfactory service at low cost, provided you give it proper care. Frequent cleaning and occasional adjusting should reward you with low operating and maintenance costs and faster, better service. DAILY CLEANING Clean cast iron open top grates with a mild soap and wat ...

  • Vulcan-Hart GCT48 - page 8

    - 8 - calling for service, the following information must be available: model number, serial number, and gas type. This information can be found on the main data plate, located on the side of the unit. PRECAUTIONS When scraping off heavy deposits of grease or oil fr om stainless steel equipment, never use ordinary steel scrapers. Particles of ordin ...

  • Vulcan-Hart GCT48 - page 9

    MODE D’INSTALLATION ET MODE D’EMPLOI PLAQUES CHAUFFANTES DE LA SÉRIE VULCAN ENDURANCE MODÈLES: GCT12 GCT24 GCT36 GCT48 GCT60 GCT72 www.vulcanhart.com Une division de Groupe ITW Équipement alimentaire, LLC 10405 Westlake Drive Charlotte, NC 28273 DOCUMENT À CO NSERVER EN CAS DE BESOIN F38202 Rév. A (07-08 ) ...

  • Vulcan-Hart GCT48 - page 10

    MESURES DE SÉCURITÉ IMPORTANTES CE MANUEL A ÉTÉ PRÉPARÉ À L ’INTENTION D’UN PERSONNEL QUALIFIÉ ET AUTORISÉ À INSTALLER DES APPAREILS FONCTIONNANT AU GAZ ET À EFFECTUER LE DÉMARRAGE INITIAL CHEZ LE CLIENT DE MÊME QUE LE RÉGLAGE DES APPAREILS CONCERNÉS DANS CE MANUEL. AFFICHER À UN ENDROIT VISIBLE LES PREMIER S SOINS À ADMI NISTR ...

  • Vulcan-Hart GCT48 - page 11

    - 3 - Installation, fonctionnement et entretien PLAQUES CHAUFFANTES DE LA SÉRIE VULCAN ENDURANCE GÉNÉRALITÊS Les plaques chauffantes Vulcan sont fabriqués avec le plus grand so in et à partir des meilleurs matériaux. Ils sont conçus en vue d’obtenir des résu ltats de cuisson satisfaisants, tout en tenant compte de l’hygiène et de la f ...

  • Vulcan-Hart GCT48 - page 12

    - 4 - Les plaques chauffantes doivent se trouver dans un endroit suffisamment espacé pour permettre leur entretien et leur fonctionnement appropriés. Un dégagement minimal de 610 mm (24 po) est requis devant l’appareil. Installer les plaques chauffantes de manière à assurer la circulation de l’air nécessaire à la combustion des gaz et à ...

  • Vulcan-Hart GCT48 - page 13

    NIVELAGE Pour niveler la plaque chauffante, déposer un niveau de menuisier sur la surface de la plaque chauffante et procéder à son nivelage d’un côté à l’autre et d’avant vers l’arrière. Terminer le nivelage en tournant chaque section de pattes si nécessaire. Tour ner les pattes dans le sens contraire des aiguilles d ’une montre ...

  • Vulcan-Hart GCT48 - page 14

    FONCTIONNEMENT La plaque chauffante et ses composants sont chauds. Exercer une extrême prudence lors de son utilisation, nettoyage ou entretien. COMMANDES Robinet de brûleur de surface de cuisson – Permet d’acheminer le gaz vers les brûleurs de la surface de cuisson. Pour l’ouvrir, tourner le bouton dans le sens contraire des aiguilles d? ...

  • Vulcan-Hart GCT48 - page 15

    - 7 - remettre en place sur la plaque chauffante), enduire les grilles d’une mince couche d’huile végétale ou vaporiser de l’huile à cuisson. Remettre les grilles en place après leur apprêtage. Ouvrir tous les brûleurs découverts et les mettre à LOW (faible intensité) et laisser chauffer pendant au moins 15 minutes avant d’y dépos ...

  • Vulcan-Hart GCT48 - page 16

    - 8 - PRÉCAUTIONS Ne jamais utiliser une racle ordinaire en acier inoxydable pour enlever les dépôts tenaces de graisse ou d’huile sur une surface en acier inoxydable. Des particules ou de l’acier ordinaire risquent de s’incruster ou de se loger dans la surface en acier inoxydable, provoquant une légère formation de rouille et possibleme ...

Manufacturer Vulcan-Hart Category Water Heater

Documents that we receive from a manufacturer of a Vulcan-Hart GCT48 can be divided into several groups. They are, among others:
- Vulcan-Hart technical drawings
- GCT48 manuals
- Vulcan-Hart product data sheets
- information booklets
- or energy labels Vulcan-Hart GCT48
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vulcan-Hart GCT48.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vulcan-Hart GCT48, service manual, brief instructions and user manuals Vulcan-Hart GCT48. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vulcan-Hart GCT48.

Similar manuals

A complete manual for the device Vulcan-Hart GCT48, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vulcan-Hart GCT48 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vulcan-Hart GCT48.

A complete Vulcan-Hart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vulcan-Hart GCT48 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vulcan-Hart GCT48, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vulcan-Hart GCT48, that we can find in the current document
3. Tips how to use the basic functions of the device Vulcan-Hart GCT48 - which should help us in our first steps of using Vulcan-Hart GCT48
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vulcan-Hart GCT48
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vulcan-Hart GCT48 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vulcan-Hart GCT48?

Use the form below

If you did not solve your problem by using a manual Vulcan-Hart GCT48, ask a question using the form below. If a user had a similar problem with Vulcan-Hart GCT48 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)