English dropdown-ico

Manual Honeywell 3200

100 pages 1.28 mb
Download

Go to site of 100

Summary
  • Honeywell 3200 - page 1

    ™ 3200 Linear Imager User’s Guide ...

  • Honeywell 3200 - page 2

    Disc laimer Honeyw ell International Inc. (“Honeywell ”) reserves the right to make changes in specifications and other inf ormation co ntained in this document without prior notice, and the reader should in all cases consult Honeyw ell to determine whether any such changes ha ve been made. The inf ormation in this publication does not represen ...

  • Honeywell 3200 - page 3

    i Chapter 1 - Getting Started About This Manual ............. .......................................... 1-1 Unpacking the Imager ................ .................................. 1-1 3200 Linear Imager Models ......................................... 1-1 Connecting the Imager with USB ................................ 1-2 USB PC or Macintosh Keyb ...

  • Honeywell 3200 - page 4

    ii Trigger .................................. ....................................... 3-1 Automatic Trigger ............ ...................................... 3-2 Reread Delay .......................... ..................................... 3-2 Chapter 4 - Data Editing Prefix/Suffix Overview.................................................. 4-1 To ...

  • Honeywell 3200 - page 5

    iii Code 39 ........................... ............................................6-4 Code 39 Start / Stop Charac ters ............................. 6-4 Code 39 Check Character . ..................................... 6-5 Code 39 Message Length . ..................................... 6-5 Full ASCII ......................... ....................... ...

  • Honeywell 3200 - page 6

    iv UPC E0 and UPC E1 ............ ..................................... 6-18 UPC E0 and UPC E1 Expand .............................. 6-18 UPC E0 and UPC E1 Addenda Required ............ 6-18 UPC E0 Check Digit ............................................ 6-19 UPC E0 Number System ..................................... 6-19 UPC E0 Addenda ........... ...

  • Honeywell 3200 - page 7

    v Chapter 9 - Default Chart Resetting the Standard Product Defaults ..................... 9-1 Menu Commands ................. ........................................ 9-1 Chapter 10 - Product Specifications 3200 Linear Imager Product Specifications ............... 10-1 Chapter 11 - Maintenance Repairs ............................................... ...

  • Honeywell 3200 - page 8

    vi ...

  • Honeywell 3200 - page 9

    3200 Imager Identification Item Number, Serial Number and Compliance Information location ...

  • Honeywell 3200 - page 10

    ...

  • Honeywell 3200 - page 11

    3200 User’s Guide 1 - 1 1 Getting Star ted About This Manual This User’s Guide provides installation and programming instructions for the 3200 linear imager. Product specifications, dimensions , warranty, and customer support information are also included. Honeywell barcode imagers are fact ory programmed for the most common terminal and commun ...

  • Honeywell 3200 - page 12

    1 - 2 3200 User’s Guide Connecting the Imager with USB Note: Honeywell recommends connecting the imager end of the cable first and the host end second. An imager can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the imager and to the computer. 2. The imager beeps. 3. Verify the imager operation by scann ...

  • Honeywell 3200 - page 13

    3200 User’s Guide 1 - 3 Plug and Play Plug and Play barcodes provide inst ant imager set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Connecting the Imager When P o wered b y Host (Ke yboar d W edge) An imager can be connec ted between the keyboard a nd PC a ...

  • Honeywell 3200 - page 14

    1 - 4 3200 User’s Guide Ke yboard W edge Connection Scanning the barcode below allows operat ion of the 3200 li near imager as a keyboard wedge interface to an IBM PC AT with a U. S. keyboard. If you programmed the imager for a differ ent terminal interfac e and you want to change to an IBM PC AT and compatible s keyboard wedge interface, scan th ...

  • Honeywell 3200 - page 15

    3200 User’s Guide 1 - 5 Note: For the imager to work properly, y ou must have the corre ct cable for your type of terminal/computer. 3. Plug the serial connector into the seri al port on your computer. Tighten the two screws to secure the connector to the port. 4. Connect the power supply and plug into an outlet. 5. Turn the terminal/computer pow ...

  • Honeywell 3200 - page 16

    1 - 6 3200 User’s Guide Reading T echniques The imager has a bright red aiming beam that corresponds to its horizontal field of view. The aiming beam should be c entered horizontally over the barcode; it will not read if the aiming be am is in any other direction. The best focus point for read ing most code densities is about 5 inches (12.7 cm) f ...

  • Honeywell 3200 - page 17

    3200 User’s Guide 2 - 1 2 T erminal Interfaces T erminal ID If your interface is not a standard PC AT, refer to Terminal ID , beginning on page 2-1 and locate the Terminal ID number for your PC. Scan the T erminal ID barcode below, then scan the numeric barcode(s) from the Programming Chart inside the back cover of this manual to pr ogram the ima ...

  • Honeywell 3200 - page 18

    2 - 2 3200 User’s Guide * Factory default Suppor ted T erminals Te r m i n a l Model(s) T erminal ID RS-232 TTL 000 USB PC K e yboard 124 * USB Mac K e yboard 125 ...

  • Honeywell 3200 - page 19

    3200 User’s Guide 2 - 3 Ke yboar d Country Scan the appropriate coun try code below to program the keyboard for your country. As a general rule, the follow ing characters are supported, but need special care for countries ot her than the United States: @ | $ # { } [ ] = / ‘ < > ~ * United States Denmark France Germany/Austria Great Brit ...

  • Honeywell 3200 - page 20

    2 - 4 3200 User’s Guide Please refer to Honeywell website ( www.honeywell.com/aidc ) for complete keyboard country support information and applicable interfaces . If you need to program a keyboard for a country other than one listed above, scan the Program Keyboard Country barcode below, then scan th e numeric barcode(s) for the appropriate count ...

  • Honeywell 3200 - page 21

    3200 User’s Guide 2 - 5 Control + ASCII Mode On: The imager sends key co mbinations for ASCII control characters for va lues 00-1F. Refer to Keyboard Function Relationships , page 7-1 for CTRL+ ASCII Values. Default = Off Numeric Ke ypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off A utomatic Direct Connect Mo ...

  • Honeywell 3200 - page 22

    2 - 6 3200 User’s Guide RS-232 Baud Rate Baud Rate sends the data from the imager to the terminal at the specified rate. The host terminal must be set for the same baud rate as the imager. Default = 38,400 . 300 2400 600 1200 4800 * 38400 9600 19200 57,600 ...

  • Honeywell 3200 - page 23

    3200 User’s Guide 2 - 7 RS-232 W ord Length: Data Bits, Stop Bits, and P arity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex charac ters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications which require use of the full ASCII set, select 8 data ...

  • Honeywell 3200 - page 24

    2 - 8 3200 User’s Guide RS-232 Handshaking RS-232 handshaking is a set of rules co ncerning the exchange of data between serially communicating devices. Def ault = R TS/CTS, XON/XOFF and A CK/ NAK Off . RTS/CTS On * XON/OFF Off * RTS/CTS Off XON/XOFF On ACK/NAK On * ACK/NAK Off ...

  • Honeywell 3200 - page 25

    3200 User’s Guide 3 - 1 3 Output Good Read Indicators Beeper – Good Read The beeper may be programm ed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Def ault = On. Beeper Pitch – Good Read The beeper pitch codes modify th ...

  • Honeywell 3200 - page 26

    3 - 2 3200 User’s Guide Au t om a t i c T ri g g e r The imager scans continuou sly at full power with illumination fully on. Reread Dela y This sets the time period before the imager can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode. Longer delays are effective in minimizing a ...

  • Honeywell 3200 - page 27

    3200 User’s Guide 4 - 1 4 Data Editing Prefix/Suffix Overview When a barcode is scanned, a dditional information is se nt to the host computer along with the barcode dat a. This group of barc ode data and additional, user-defined data is called a “message stri ng.” The selections in this section are used to build the user-defined data into th ...

  • Honeywell 3200 - page 28

    4 - 2 3200 User’s Guide T o Add a Prefix or Suffix: Step 1. Scan the Add Prefix or Add Suffix symbol ( page 4-3 ). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the ) for the symbology to which you w ant to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Sca ...

  • Honeywell 3200 - page 29

    3200 User’s Guide 4 - 3 T o Clear One or All Prefixes or Suffix es: You can clear a single prefix or suffix , or clear all prefixes/suffixes for a symbology. When you Clear One Prefix (Suffix), the specific character you select is deleted from the symbology you want. When you Clear All Prefixes (Suffixes), all the prefixes or su ffixes for a symb ...

  • Honeywell 3200 - page 30

    4 - 4 3200 User’s Guide Suffix Selections Function Code T ransmit When this selection is enabled and fu nction codes are contained within the scanned data, the imager transmits the functi on code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 7-3 . When the imager is in keyboard wedge mod ...

  • Honeywell 3200 - page 31

    3200 User’s Guide 4 - 5 Interc haracter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay barcode below, then scan the nu mber of milliseconds and the SAVE barcode using the Programming Chart inside the back cover of this manual. To remov ...

  • Honeywell 3200 - page 32

    4 - 6 3200 User’s Guide Intermessage Delay An intermessage delay of up to 495 mi lliseconds may be plac ed between each scan transmission. Scan the Intermessage Delay barcode below, then scan the number of milliseconds and the SAVE barcode using the Programming Chart inside the back cover of this manual. To remove this delay, scan the Intermessag ...

  • Honeywell 3200 - page 33

    3200 User’s Guide 5 - 1 5 Data Formatting Data Format Editor Intr oduction You may use the Data Format Editor to change the imager’s output. For example, you can use the Data Format Ed itor to insert characters at certain points in barcode data as it is scanned. The selections in the following pages are used only if you wish to alter the output ...

  • Honeywell 3200 - page 34

    5 - 2 3200 User’s Guide ming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a univer sal number, indicating all lengths.) Step 5. Editor Commands Refer to the Format Editor Commands Chart ( page 5-2 ). Scan the symbols that represent the command you want to enter. 94 alphanu- meric characters may be e ...

  • Honeywell 3200 - page 35

    3200 User’s Guide 5 - 3 Move Commands F5 Move the cursor ahead “nn” characte rs from current cursor position. Syntax = F5nn (nn stands for the numeric value (00-99) for the number of characters the cursor should be moved ahead.) F7 Move the cursor to the begi nning of the data string. Syntax = F7 . Miscellaneous Commands FE Compare character ...

  • Honeywell 3200 - page 36

    5 - 4 3200 User’s Guide Data Formatter When Data Formatter is turned off, the ba rcode data is output to the host as read (including prefixes and suffixes). Ch oose one of the following options. Default = Data Formatter On. When Data Formatter is required, all input data must conform to an edited format or the imager does not transmit the input d ...

  • Honeywell 3200 - page 37

    3200 User’s Guide 6 - 1 6 Symbologies Intr oduction This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults. All Symbologies If you want to decode all the symbolog ies allowable for your imager, scan the All Symbologies On code. If on the other hand , you want to decode only a particular symbo ...

  • Honeywell 3200 - page 38

    6 - 2 3200 User’s Guide EXAMPLE: Decode only those barcodes with a count of 9-20 characters. Min. length = 09 Max. length = 20 EXAMPLE: Decode only those barcodes wi th a count of 15 characters. Min. length = 15 Max. length = 15 For a value other than the minimum an d maximum message length defaults, scan the barcodes included in the explanation ...

  • Honeywell 3200 - page 39

    3200 User’s Guide 6 - 3 No Check Character indicates that the imager reads and transmits barcode data with or without a check character. When Check Character is set to V alidate and T ransmit , the imager will only read Codabar barcodes printed with a ch eck character, and will transmit this character at the end of the scanned data. When Check Ch ...

  • Honeywell 3200 - page 40

    6 - 4 3200 User’s Guide Code 39 < Default All Code 39 Settings > Code 39 Code 39 Start / Stop Character s Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not tr ansmit Start/Stop characters. Default = Don’t Transmit. * On Off Transmit * Don’t Transmit ...

  • Honeywell 3200 - page 41

    3200 User’s Guide 6 - 5 Code 39 Check Character No Check Character indicates that the imager reads and transmits barcode data with or without a check character. When Check Character is set to V alidate , but Don’t T ransmit , the unit only reads Code 39 barcodes printed with a ch eck character, but wi ll not transmit the check character with th ...

  • Honeywell 3200 - page 42

    6 - 6 3200 User’s Guide Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the barcode symbol will be interpreted as a si ngle character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off . Character pairs /M and /N decode as a minus sign an ...

  • Honeywell 3200 - page 43

    3200 User’s Guide 6 - 7 Code 39 Code P age Code pages define the mapping of characte r codes to characters. If the data received does not display with the prop er characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expe cting. If this is the ca se, scan the barco ...

  • Honeywell 3200 - page 44

    6 - 8 3200 User’s Guide When Check Digit is set to V alidate, but Don’t T ransmit , the unit only reads Interleaved 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to V alidate and T ransmit , the imager only reads Interleaved 2 of 5 barcodes printed with a check d ...

  • Honeywell 3200 - page 45

    3200 User’s Guide 6 - 9 Code 93 < Default All Code 93 Settings > Code 93 Code 93 Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-1 for additi onal information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Code 93 Code P age Code pages define the mappin ...

  • Honeywell 3200 - page 46

    6 - 10 3200 User’s Guide S traight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Settings> Straight 2 of 5 Industrial Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional info rmation. Minimum and Maximum lengths = 1-48. Min ...

  • Honeywell 3200 - page 47

    3200 User’s Guide 6 - 11 S traight 2 of 5 IA T A Straight 2 of 5 IA T A Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-1 for additi onal information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matri ...

  • Honeywell 3200 - page 48

    6 - 12 3200 User’s Guide Matrix 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional info rmation. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Code 1 1 <Default All Code 11 Settings> Code 11 Check Digits Required This option sets whe ...

  • Honeywell 3200 - page 49

    3200 User’s Guide 6 - 13 Code 11 Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-1 for additi onal information. Minimum and Maximum lengths = 1-80. Minimum Defa ult = 4, Maximum Default = 80. Code 128 <Default All Code 128 Settings> Code 128 ISBT 128 Concatenation In 1994 the Internati ...

  • Honeywell 3200 - page 50

    6 - 14 3200 User’s Guide Code 128 Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional info rmation. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Code 128 Code P age Code pages define the mapping of charac ter codes to characters. If the data rece ...

  • Honeywell 3200 - page 51

    3200 User’s Guide 6 - 15 Te l e p e n T elepen Output Using AIM Telepen Output, the imager re ads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the imager reads symbols with start/stop pattern 1 and decodes them as compressed numeri c with optional full ...

  • Honeywell 3200 - page 52

    6 - 16 3200 User’s Guide UPC A <Default All UPC A Settings> UPC A UPC A Check Digit This selection allows you to specif y whether the check digit should be transmitted at the end of the sca nned data or not. Default = On. UPC A Number System The numeric system digit of a U.P.C. sy mbol is normally transmitted at the beginning of the scanned ...

  • Honeywell 3200 - page 53

    3200 User’s Guide 6 - 17 This selection adds 2 or 5 digits to the end of all scanned UPC A data. Default = Off for both 2 Digit and 5 Digit Addenda. UPC A Addenda Required When Addenda Required is set to on, the im ager will only read UPC A barcodes that have addenda. Default = Not Required. UPC-A/EAN-13 with Extended Coupon Code Use the followin ...

  • Honeywell 3200 - page 54

    6 - 18 3200 User’s Guide UPC E <Default All UPC E Settings> UPC E0 and UPC E1 Most U.P.C. barcodes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1). UPC E0 and UPC E1 Expand UPC E Expand exp ...

  • Honeywell 3200 - page 55

    3200 User’s Guide 6 - 19 UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. UPC E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the un it can be programmed so it will not transmit ...

  • Honeywell 3200 - page 56

    6 - 20 3200 User’s Guide EAN/J AN 13 EAN/JAN 13 Chec k Digit This selection allows you to specif y whether the check digit should be transmitted at the end of the scanned data or not. Default = On. EAN/JAN 13 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda. E ...

  • Honeywell 3200 - page 57

    3200 User’s Guide 6 - 21 EAN/JAN 13 Ad denda Separator When this feature is on, th ere is a space between the data from the barcode and the data from the addenda. When tu rned off, there is no space. Default = On. Note: If you want to enable or disabl e EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code on page 6-17. ...

  • Honeywell 3200 - page 58

    6 - 22 3200 User’s Guide EAN/JAN 8 Chec k Digit This selection allows you to specif y whether the check digit should be transmitted at the end of the scanned data or not. Default = On. EAN/JAN 8 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda. EAN/JAN 8 Ad den ...

  • Honeywell 3200 - page 59

    3200 User’s Guide 6 - 23 EAN/JAN 8 Ad denda Separator When this feature is on, th ere is a space between the data from the barcode and the data from the addenda. When tu rned off, there is no space. Default = On. MSI <Default All MSI Settings> MSI MSI Check Character Different types of check characters are used with MSI barcodes. You can pr ...

  • Honeywell 3200 - page 60

    6 - 24 3200 User’s Guide MSI Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional info rmation. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Plessey Code <Default All Plessey Code Settings> Plessey Code Plessey Message Length Scan the barcod ...

  • Honeywell 3200 - page 61

    3200 User’s Guide 6 - 25 RSS-14 RSS Limited < Default All RSS Limited Settings > RSS Limited RSS Expanded < Default All RSS Expanded Settings > * On Off * On Off ...

  • Honeywell 3200 - page 62

    6 - 26 3200 User’s Guide RSS Expanded RSS Expanded Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-1 for additional info rmation. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. EAN • UCC Emulation The imager can automatically format the output from any EAN• ...

  • Honeywell 3200 - page 63

    3200 User’s Guide 6 - 27 China P ost Code China P ost Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-1 for additi onal information. Minimum and Maximum lengths = 2-80. Minimum Defa ult = 4, Maximum Default = 80. On * Off Minimum Message Length Maximum Message Length ...

  • Honeywell 3200 - page 64

    6 - 28 3200 User’s Guide ...

  • Honeywell 3200 - page 65

    3200 User’s Guide 7 - 1 7 Interface K e ys Ke yboar d Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all termin als that can be used with the imager. Refer to page 2-5 enable Control + ASCII mode. Function Code HEX/ASCII Value Full ASCII “CTRL” + NUL 00 2 SOH 01 ...

  • Honeywell 3200 - page 66

    7 - 2 3200 User’s Guide The last five characters in the Full ASCII “C TRL”+ column ( [ ] 6 - ), apply to US only. The following chart indicates the eq uivalents of these five characters for different countries. Country Codes United States [ ] 6 - B e l g i u m [<]6 - Scandinavia 8 < 9 6 - France ^ 8 $ 6 = Germany à + 6 - Italy + ...

  • Honeywell 3200 - page 67

    3200 User’s Guide 7 - 3 Supported Interface Keys ASCII HEX IBM A T/XT and PS/2 Compatibles, WYSE PC/A T Supported Keys IBM XT s and Compatibles Supported Keys NUL 00 Reserved Reserved SOH 01 Enter (KP) CR/Enter STX 02 Cap Lock Caps Lock ETX 03 ALT make Reserved EOT 04 ALT break Reserved ENQ 05 CTRL make Reserved ACK 06 CTRL break Reserved BEL 07 ...

  • Honeywell 3200 - page 68

    7 - 4 3200 User’s Guide ...

  • Honeywell 3200 - page 69

    3200 User’s Guide 8 - 1 8 Utilities T o Add a T est Code I.D . Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, included in the , page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, ...

  • Honeywell 3200 - page 70

    8 - 2 3200 User’s Guide ...

  • Honeywell 3200 - page 71

    3200 User’s Guide 9 - 1 9 Default Char t Resetting the Standar d Pr oduct Defaults If you aren’t sure what programming op tions are in your imager, or you’ve changed some options and want the factory settings restored, scan the Standard Product Default Settings barcode below. The chart on the following pages lists the fa ctory default setting ...

  • Honeywell 3200 - page 72

    9 - 2 3200 User’s Guide K e yboard Modifiers *Control + ASCII Off 2-5 Control + ASCII On 2-5 *Numeric Ke ypad Off 2-5 Numeric Ke ypad On 2-5 *A uto Direct Conn. Off 2-5 A uto Direct Conn. On 2-5 Serial P or t Connection RS-232 1-5 Baud Rate 300 BPS 2-6 600 BPS 2-6 1200 BPS 2-6 2400 BPS 2-6 4800 BPS 2-6 9600 BPS 2-6 19200 BPS 2-6 *38400 BPS 2-6 57 ...

  • Honeywell 3200 - page 73

    3200 User’s Guide 9 - 3 RS-232 Handshaking *R TS/CTS Off 2-8 RT S/ C T S O n 2-8 *XON/XOFF Off 2-8 XON/XOFF On 2-8 *A CK/NAK Off 2-8 AC K /N A K O n 2-8 Output Selections Beeper - Good Read Off 3-1 *On 3-1 Beeper V olume - Good Read Off 3-1 Low 3-1 Medium 3-1 *High 3-1 Beeper Pitch - Good Read (F requency) Low (1600) (min 400Hz) 3-1 *Medium (2550 ...

  • Honeywell 3200 - page 74

    9 - 4 3200 User’s Guide Function Code T rans- mit *Enable 4-4 Disable 4-4 Intercharacter Dela y 4-5 Interfunction Dela y 4-5 Intermessage Delay 4-6 Data Formatter Selections Data Fo rmat Editor *Def ault Data F ormat (None) 5-3 Enter Data F ormat 5-3 Clear One Data F ormat 5-3 Clear All Data Fo r mats 5-3 Data Fo rm atter Off 5-4 * On, but Not Re ...

  • Honeywell 3200 - page 75

    3200 User’s Guide 9 - 5 Code 39 Star t/Stop Char . * Don’t T ransmit 6-4 T ransmit 6-4 Code 39 Check Char . * No Check Char . 6-5 V alidate, But Don’t T ransmit 6-5 Va l i d a t e , and T ransmit 6-5 Code 39 Message Length Minimum (0 - 48) *0 6-5 Maximum (0 - 48) *48 6-5 Code 32 Pharmaceuti- cal (P ARAF) *Off 6-5 On 6-5 Code 39 Full ASCII *Of ...

  • Honeywell 3200 - page 76

    9 - 6 3200 User’s Guide Straight 2 of 5 Indus- trial Message Length Minimum (1 - 48) *4 6-10 Maximum (1 - 48) *48 6-10 Straight 2 of 5 IA T A Def ault All Straight 2 of 5 IA T A Settings 6-11 Straight 2 of 5 IA T A *Off 6-11 On 6-11 Straight 2 of 5 IA T A Message Length Minimum (1 - 48) *4 6-11 Maximum (1 - 48) *48 6-11 Matrix 2 of 5 Def ault All ...

  • Honeywell 3200 - page 77

    3200 User’s Guide 9 - 7 Code 128 Function Code T ransmit *Off 6-14 On 6-14 ISBT Concatenation *Off 6-13 On 6-13 T elepen Def ault All T elepen Settings 6-15 T elepen *Off 6-15 On 6-15 T elepen Output *AIM T elepen Output 6-15 Original T elepen Output 6-15 T elepen Message Length Minimum (1 - 60) *1 6-15 Maximum (1 - 60) *60 6-15 UPC A Def ault Al ...

  • Honeywell 3200 - page 78

    9 - 8 3200 User’s Guide UPC E Expand *Off 6-18 On 6-18 UPC E Check Digit Off 6-19 *On 6-19 UPC E Number Sys- tem Off 6-19 *On 6-19 UPC E 2 Digit Addenda *Off 6-19 On 6-19 UPC E 5 Digit Addenda *Off 6-19 On 6-19 UPC E Addenda Required *Not Required 6-18 Required 6-18 EAN/JAN 13 Def ault All EAN/ JAN 13 Settings 6-20 EAN/JAN 13 Off 6-20 *On 6-20 EA ...

  • Honeywell 3200 - page 79

    3200 User’s Guide 9 - 9 EAN/JAN 8 Chec k Digit Off 6-22 *On 6-21 EAN/JAN 8 2 Digit Addenda *Off 6-22 On 6-22 EAN/JAN 8 5 Digit Addenda *Off 6-22 On 6-22 EAN/JAN 8 Addenda Required *Not Required 6-22 Required 6-22 EAN/JAN 8 Addenda Separator Off 6-23 *On 6-23 Coupon Code Off 6-23 *On 6-17 MSI Def ault All MSI Settings 6-23 MSI *Off 6-23 On 6-23 MS ...

  • Honeywell 3200 - page 80

    9 - 10 3200 User’s Guide RSS Limited Off 6-25 *On 6-25 RSS Expanded Def ault All RSS-14 Expanded Settings 6-26 RSS Expanded Off 6-26 *On 6-26 RSS Expanded Msg. Length Minimum (4 - 74) *4 6-26 Maximum (4 - 74) *74 6-26 EAN•UCC Emulation RSS Emulation 6-26 128 Emulation 6-26 *EAN•UCC Emulation Off 6-26 China P ost Code Default All China P ost C ...

  • Honeywell 3200 - page 81

    3200 User’s Guide 10 - 1 10 Pr oduct Specifications 3200 Linear Imager Pr oduct Specifications P arameter Specification Dimensions (T ypical): Height 3.8 inches (9.52 cm) Length 6 inches (15.3 cm) Width 2.7 inches (6.8 cm) Weight 5.1 ounces (145 g) Light Source 626 nm ± 30mn visible red LED Scan Rate 270 scans per second in most usages Ske w Ang ...

  • Honeywell 3200 - page 82

    10 - 2 3200 User’s Guide S tandard Cable Pinouts Keyboard W edge 10 Pin RJ41 Modular Plug connects to the imager handle 1 2 Cord shield 3 Tied to supply power 4 Supply ground 5 Terminal clock 6 Terminal data 7 Supply power input (Refer to tables on page 10-1 ) 8 Keyboard data 9 Keyboard clock 10 ...

  • Honeywell 3200 - page 83

    3200 User’s Guide 10 - 3 S tandard Cable Pinout s Serial Output 10 Pin RJ41 Modular Plug connects to the imager handle 1 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 Receive data - Serial data to imager 6 Transmit data - Serial data from imager 7 Supply power input (Refer to tables on page 10-1 ) 8 Request to ...

  • Honeywell 3200 - page 84

    10 - 4 3200 User’s Guide S tandard Cable Pinouts USB 10 Pin Modular Plug connects to the imager handle 1 2 Data + 3 Tied to supply power 4 Supply ground 5 6 7 5 volt supply power input 8 9 10 Data - ...

  • Honeywell 3200 - page 85

    3200 User’s Guide 11 - 1 11 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center. Please see Customer Support on page 12-1 for further information. Maintenance The 3200 linear imager provides reliable and efficient operation with a minimum of c ...

  • Honeywell 3200 - page 86

    11 - 2 3200 User’s Guide Replacing the Interface Cable The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in the 3200 linear imager’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. • Order replacement cables fr om a ...

  • Honeywell 3200 - page 87

    3200 User’s Guide 11 - 3 Is the scanner having troub le reading your symbols? If the scanner isn’t r eading symbols well, ch eck that the symbols: • Aren’t smeared, rough, scratched, or exhibiting voids. • Aren’t coated with frost or wa ter droplets on the surface. • Are enabled in the scanner or in the decoder to which the scanner co ...

  • Honeywell 3200 - page 88

    11 - 4 3200 User’s Guide ...

  • Honeywell 3200 - page 89

    3200 User’s Guide 12 - 1 12 Customer Suppor t T echnical Assistance If you need assistance installing or trouble shooting, please call your Distributor or the nearest techni cal support office: North America/Canada Telephone: (800) 782-4263 Fax number: (315) 554-6705 E-mail: natechsupport@handheld.com Latin America Telephone: (803) 835-8000 Telep ...

  • Honeywell 3200 - page 90

    12 - 2 3200 User’s Guide Pr oduct Service and Repair Honeywell provides service for all it s products through service centers throughout the world. To obtain warrant y or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product. North America Telephone: (800 ...

  • Honeywell 3200 - page 91

    3200 User’s Guide 12 - 3 specifications applicable to the products purchased at the time of shipment. This warranty does not co v er any Hone yw ell product which is (i) improperly installed or used; (ii) dama ged by accident or negligence , including f ailure to f ol- low the proper maintenance , ser vice, an d cleaning schedule; or (iii) damage ...

  • Honeywell 3200 - page 92

    12 - 4 3200 User’s Guide All provisions of this Limited W arran ty are separate and sev er able , which means that if any pro vision is held in v alid and unenf orceab le, such determina- tion shall not aff ect the validity of enf orc eability of the other provisions hereof . Use of any peripherals not manuf actured /sold by Honeyw ell ma y resul ...

  • Honeywell 3200 - page 93

    3200 User’s Guide A - 1 A Appendix A Symbology Char t Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Iden tifiers, for AIM modifier character details. Note: Prefix / Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. Refer to Data Editing begi ...

  • Honeywell 3200 - page 94

    A - 2 3200 User’s Guide ASCII Con version Chart (Code Pa ge 1252 ) Note: This table applies to U.S. st yle keyboards. Certain charac ters may differ depending on your Country Code/PC regional settings. Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char 0 00 NUL 32 20 64 40 @ 96 60 ‘ 1 01 SOH 33 21 ! 65 41 A 97 61 a 2 02 STX 34 22 “ 66 42 B 9 ...

  • Honeywell 3200 - page 95

    3200 User’s Guide A - 3 Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char 128 80 € € 160 A0 192 C0 À 224 E0 à 129 81 161 A1 ¡ 193 C1 Á 225 E1 á 130 82 ‚ 162 A2 ¢ 194 C2 Â 226 E2 â 131 83 ƒ 163 A3 £ 195 C3 Ã 227 E3 ã 132 84 „ 164 A4 ¤ 196 C4 Ä 228 E4 ä 133 85 … 165 A5 ¥ 197 C5 Å 229 E5 å 134 86 † 166 A6 ¦ 198 C6 Æ ...

  • Honeywell 3200 - page 96

    A - 4 3200 User’s Guide Code P a ge Mapping of Printed barcodes Code pages define the mapping of charac ter codes to characters. If the data received does not display with the pr oper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If th is is the ...

  • Honeywell 3200 - page 97

    Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN 13 1234567890 Code 128 9 780330 290951 654 EAN 8 3210 5 456123 8 0 UPC-E ...

  • Honeywell 3200 - page 98

    Sample Symbols Code 93 123456-9$ Straight 2 of 5 Industrial 123456 Matrix 2 of 5 6543210 RSS-14 (01)00123456789012 Code 39 Codabar BC321 A13579B ...

  • Honeywell 3200 - page 99

    Programming Chart A C Save B Discard F E D Note: If you make an error while scanning t he letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save . 0 2 6 1 7 5 4 3 8 9 ...

  • Honeywell 3200 - page 100

    Honeywell 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208 3200-UG Rev B 5/08 ...

Manufacturer Honeywell Category Automobile Accessories

Documents that we receive from a manufacturer of a Honeywell 3200 can be divided into several groups. They are, among others:
- Honeywell technical drawings
- 3200 manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell 3200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell 3200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell 3200, service manual, brief instructions and user manuals Honeywell 3200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell 3200.

Similar manuals

A complete manual for the device Honeywell 3200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell 3200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell 3200.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell 3200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell 3200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell 3200, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell 3200 - which should help us in our first steps of using Honeywell 3200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell 3200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell 3200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell 3200?

Use the form below

If you did not solve your problem by using a manual Honeywell 3200, ask a question using the form below. If a user had a similar problem with Honeywell 3200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (1)

pastuh

Я и пользователь LG MS-196U, и техник по обслуживанию электронной аппаратуры.Поэтому мне необходимо иметь и сервисную документацию, и инструкцию по эксплуатации.