English dropdown-ico

Manual Pelco 100 Series

16 pages 0.18 mb
Download

Go to site of 16

Summary
  • Pelco 100 Series - page 1

    100 Series Camclosure ® Integrated Camera System W ith LowLight ™ DSS T echnology C2460M-A (7/03) ® INST ALLA TION/OPERA TION ...

  • Pelco 100 Series - page 2

    2 C2460M-A (7/03) LIST OF ILLUSTRA TIONS Figure Page 1 Installation Directly to a Wall/Ceiling ....................................................................................... ... 5 2 Installation Directly to a Concrete Wall/Ceiling ........................................................................... 6 3 Installation on a 4S Electrica ...

  • Pelco 100 Series - page 3

    C2460M-A (7/03) 3 Heater elements could be hot! When camera power is on, use caution when adjusting the camera. CAUTION IMPORT ANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or ...

  • Pelco 100 Series - page 4

    4 C2460M-A (7/03) WELCOME Thank you for purchasing Pelco’ s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology . Y our new ICS100 Series surface mount dome system includes a high-resolution, low light, color camera with auto iris and varifocal lens. The LowLight color camera has extended DSS settings ...

  • Pelco 100 Series - page 5

    C2460M-A (7/03) 5 INST ALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove the lower dome and place it to the side. INST ALL THE BACK BOX The installation methods for the ICS100 back box include the following: • Attach Directly to a Wall/Ceiling • Attach Directly t ...

  • Pelco 100 Series - page 6

    6 C2460M-A (7/03) Figure 3. Installation on a 4S Electrical Box 8-32 X .750 FLAT HEAD SCREW (SUPPLIED) 8-32 X .375 PAN HEAD SCREW (SUPPLIED) WALL OR CEILING ADAPTER PLATE BASE 4S ELECTRICAL BOX Attach Directly to Concrete Wall/Ceiling Refer to Figure 2 for the following steps. 1. Attach the base to the wall or ceiling (hardware not supplied). 2. Do ...

  • Pelco 100 Series - page 7

    C2460M-A (7/03) 7 Mount to a Plaster Ring Refer to Figure 4 for the following steps. Installation instructions assume that the 4S electrical box and plaster ring were previously installed. 1. Pull video and power wires into the base. 2. Attach the base to the plaster ring. - Use the two 8-32 x .750-inch pan head screws to attach the base to a 401 p ...

  • Pelco 100 Series - page 8

    8 C2460M-A (7/03) Figure 5. Terminal Block for Input Power CONNECT POWER WIRES Depending on the input voltage, connect either the 12 VDC or 24 V AC input power wires to the terminal block inside the base. Refer to Figure 5 for the location of the terminal block. DC Operation – Refer to the enlarged portion of Figure 5 for the 12 VDC (+) and groun ...

  • Pelco 100 Series - page 9

    C2460M-A (7/03) 9 INST ALL THE CAMERA MODULE CHECK HEA TER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater . If the unit will never be subjected to a frost temperature, you can disable the heater , saving power requirements. T o disable the heater , remove the jumper cover from the ...

  • Pelco 100 Series - page 10

    10 C2460M-A (7/03) W all Mounting – The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab. Ceiling Mounting – The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction. CAMERA BRACKET T AB AL WA YS POINTS OUT OF THE ENCLOSURE TOP OF CAMERA C ...

  • Pelco 100 Series - page 11

    C2460M-A (7/03) 11 Figure 7. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring. Refer to Figure 7. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise. 4. T ighten the focus locking screw . DIGIT AL SLO ...

  • Pelco 100 Series - page 12

    12 C2460M-A (7/03) AGC (AUTOMA TIC GAIN CONTROL) AGC automatically adjusts the image to compensate for changes in light levels. ON (Default setting) – Enables the AGC mode. OFF – Disables the AGC mode. BLC (BACK LIGHT COMPENSA TION) The BLC (backlight compensation) feature compensates for backlit scenes by enhancing objects in the center of the ...

  • Pelco 100 Series - page 13

    C2460M-A (7/03) 13 Figure 8. Window Adjustment REINST ALL THE LOWER DOME AND TRIM RING 1. Domes with Liners (only) – Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves. Move dome into position. c. T ighten t ...

  • Pelco 100 Series - page 14

    14 C2460M-A (7/03) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC, ±10%, auto-sensing Power Consumption: 13 watts or less V ideo Connector: BNC General Operating T emperature: -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Pan/T ilt Adjustment: Manual; 360° pan; 180° tilt Construction: Aluminum with steel camera ...

  • Pelco 100 Series - page 15

    C2460M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2460M 4/03 Preliminary manual for beta testing. C2460M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will re ...

  • Pelco 100 Series - page 16

    World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada ® ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco 100 Series can be divided into several groups. They are, among others:
- Pelco technical drawings
- 100 Series manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco 100 Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco 100 Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco 100 Series, service manual, brief instructions and user manuals Pelco 100 Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco 100 Series.

Similar manuals

A complete manual for the device Pelco 100 Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco 100 Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco 100 Series.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco 100 Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco 100 Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco 100 Series, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco 100 Series - which should help us in our first steps of using Pelco 100 Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco 100 Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco 100 Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco 100 Series?

Use the form below

If you did not solve your problem by using a manual Pelco 100 Series, ask a question using the form below. If a user had a similar problem with Pelco 100 Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)