English dropdown-ico

Manual JAI CV-A11

25 pages 1.18 mb
Download

Go to site of 25

Summary
  • JAI CV-A11 - page 1

    Progressive Scan Monochrome CCD Camera CV -A11 Operation Manual Camera: Revision B Manual: Version 2.1 A11Manualjul15 JPT 15-07-03 ...

  • JAI CV-A11 - page 2

    CV-A11 DECLARA TION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EE C EMC (ELECTROMAGNETIC COMPAB ILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV ISIONS APPLYING TO IT. EN-50081-1 EN-50082-1 Table of Contents 1. General.......................................................................................... ...

  • JAI CV-A11 - page 3

    CV-A11 1. Gener al The CV-A11 is a monochrome progressive scan 1/3” CCD cameras, designed for automated inspection application, featuring an extremely small housing and a wide range of unique functions. The asynchronous trigger can be set to work in several modes, to all ow functions such as pulse width controlled shutter, programmable shutter sp ...

  • JAI CV-A11 - page 4

    CV-A11 4. Camer a Housing and Dimensions Fig. 1. Locations and dimensions. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface. 4. Gain potentiometer for manual gain setting. 5. Mounting holes, 8 x ...

  • JAI CV-A11 - page 5

    CV-A11 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin configuration is compatible with EIAJ standard Pin no. Signal Remarks 1 GND 2 +12 V DC input 3 GND 4 Video output Parallel with t he BNC connector. 5 GND 6 HD input /HD output *) SW2.1 on for 75 Ω . SW1.1 ...

  • JAI CV-A11 - page 6

    CV-A11 5.3. Input and Output Circuits In the following schematic diagrams the input and outpu t circuits for video and timing signa ls are shown. For alternative connections refer t o “10.1. CV-A11 emulating CV-M10 interfacing.” Jumper settings are shown as for factory defaul t. 5.3.1. Video output GND #4/ 12 75 Video Out put NC 82p 2 µ 7 CXA1 ...

  • JAI CV-A11 - page 7

    CV-A11 6. F unctions and Oper ations Apart from the standard continuous operation, t h e CV-A11 features three external asynchronous trigger modes (edge pre-select, pulse width cont rolled and start/stop) and a special frame-delay readout mode. Long integration ti me mode is also supp orted. In addition, the CV-A11 also provide s a partial scan rea ...

  • JAI CV-A11 - page 8

    CV-A11 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, th e camera will synchronize to it. If no external sync signals are applied, the camera will oper ate with its internal x-tal controlled sync. The camera scanning ...

  • JAI CV-A11 - page 9

    CV-A11 6.4. External Trigger Modes This camera has 6 external asynchr onous trigger modes, which can be s et by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. (HC=0, H C=1) 3. Frame Delay read out mode. TR=3 PWC exposure read out by ext. VD. (HC=0 ...

  • JAI CV-A11 - page 10

    CV-A11 6.5. Edge Pre-select Mode An external trigger pulse initiates the capture (inp ut on pin 11 of the 12-pin Hirose connector or pin 5 of the 6-pin Hirose). The leading edge of the trigger pulse initiates the exposure (this is a falling edge if factory default). If the polarity of this pulse is reversed, the camera can be configured to correct ...

  • JAI CV-A11 - page 11

    CV-A11 6.6. Pulse Width Control Mode The leading edge of the trigger pulse initiates the capture. The exposure time (acc umulation time) is governed by the duration of the trigger pulse. If the polarity of this pulse is reversed, the camera can be configured to correct for it. The exposure time range is 1.5H to 1000H (shortest and longest pulse d u ...

  • JAI CV-A11 - page 12

    CV-A11 6.7. Frame-delay read out Mode This mode allows simultaneous c apture of multiple camera using a common external trigger pulse subsequent multiplexed (sequential) readou t using a single input frame grab ber, as the user has control over when the image is read ou t from the CCD sensor. The exposure starts at the falling edge of the ext. trig ...

  • JAI CV-A11 - page 13

    CV-A11 6.8. Long Time Exposure Mode The exposure time is the interval between 2 ext. VD pulses sent to the VD input of the camera (Pin No. 7 of the 12-pin Hirose connector). The ex posure starts after input of the first ext. VD pulse, and ends after the next input of the ne xt ext. VD pulse, which ag ain starts a new exposure. The long time exposur ...

  • JAI CV-A11 - page 14

    CV-A11 6.9. Start/Stop Mode The exposure time is controlled by the interval between the ext. trigger and the ext. VD signal. The exposure starts at the first HD pulse after t he falling edge of the ext. trigger, and stops at the rising edge of the VD pulse. The range can be between 1/30 to 1/10,000 secon d. The Start/Stop mode is a continuous mode ...

  • JAI CV-A11 - page 15

    CV-A11 6.10. Smearless Mode This mode will reduce the unwant ed smear signal from a highlighted scene when a short exposure time is used. The trigger mode is like edge pre-se lect, but a fast dump readout is performed before the active accumulation is started. It will remove the smear over the highlighted parts in the image, but there is still smea ...

  • JAI CV-A11 - page 16

    CV-A11 6.11. Partial scan readout mode This mode allows increased frame rate, as only a selected number of lines are re ad out. The vertical resolution is reduced as ou tlined below. Partial scan will operate in normal continuous mode and all trigger modes. Fig. 23. Partial scanning. The partial scanning settings are as follows: Readout format Fram ...

  • JAI CV-A11 - page 17

    CV-A11 6.12. Other Functions Gain and analogue settings. !! Do not adjust these s ettings unless you have knowl edge to video adjustments !! AS, AGC Switch The video gain can be set to AGC or manual . In AGC mode the video level is kept constant by the automatic gain control circuit within a 12 dB range. Normal 700 mVpp ± 30 mV. The level can be a ...

  • JAI CV-A11 - page 18

    CV-A11 7. Configuring the Camer a 7.1. RS-232C control. All configuration of the CV-A11 camera is done via the RS-232C port. The camera can be set up from a PC running terminal emulator softwa re, or using JAI´s camera control software. Below is the description of the ASCII based short command p rotocol. Communication setting. Baud Rate 9600 bps D ...

  • JAI CV-A11 - page 19

    CV-A11 7.2. CV-A11 RS-232C command list. Command Name Format Parameter Remarks A – General settings and useful commands EB Echo Back EB= [ Param. ] <CR><LF> 0=Echo off 1=Echo on Off at power up ST Camera Status request ST?<CR><LF> Actual setting HP Online Help reques t HP?<CR><LF> Command list VN F irmware vers ...

  • JAI CV-A11 - page 20

    CV-A11 7.3. Camera Control Tool for CV-A11 From www.jai.com CV-A11 Camera Control Tool for Wi ndows 98/NT/20 00 can be downloaded. The control tool contents a camera control program and tools for m aking your own program. Below the different windows are sh own. Control bar Windows for all functions Fig. 25. Windows from Camera Tools. For the integr ...

  • JAI CV-A11 - page 21

    CV-A11 7.4. Internal Switch and Jumper Settings. 7.4.1. HD/VD input-output selection In the default setting the camera will accept external HD/VD signals on pins 6 and 7 of the 12 pin Hirose connector. The compos ite video signal from the camera will be synchr onized to an external HD/VD source connected to the camera. TTL level (between 2 and 5 V) ...

  • JAI CV-A11 - page 22

    CV-A11 8. Specifications Specifications CV-A11 Scanning System Progressive 525 lines 30 frames/sec Frame rate (Full frame) 29.96 Hz Line frequency 15.734 kHz CCD sensor Monochrome 1/3” IT CCD. Sony ICX424AL, (ICX084AL-6, old) Sensing area 4.9 (h) x 3.7 (v) mm Effective pixels 659 (h) x 494 (v) Pixels in video output 648 (h) x 492 (v) Cell size 7. ...

  • JAI CV-A11 - page 23

    CV-A11 10. Appendix 10.1. CV-A11 emulating CV-M10 interfacing The CV-A11 has a slightly different pin configu r ation on the 12-pin Hirose connector, compared to the M-series. This new configura tion is compliant to the EIA-J standa rd. This means, however, that the CV-A11 is not completely backward co mpatible with the CV-M10, CV-M40, etc in all c ...

  • JAI CV-A11 - page 24

    CV-A11 10.2. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components. Do not attempt to disassemble this camera. Do not expose ...

  • JAI CV-A11 - page 25

    CV-A11 11. Users Record Camera type: CV-A11 Revision: (Revision A) Serial No. …………….. For camera revision hi story, please contact your local JAI d istributor. Users Mode Settings: Users Modifications: Company and product names mentioned in this manual are trademarks or registered trademarks of their respective owners. JAI A-S cannot be h ...

Manufacturer JAI Category Security Camera

Documents that we receive from a manufacturer of a JAI CV-A11 can be divided into several groups. They are, among others:
- JAI technical drawings
- CV-A11 manuals
- JAI product data sheets
- information booklets
- or energy labels JAI CV-A11
All of them are important, but the most important information from the point of view of use of the device are in the user manual JAI CV-A11.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JAI CV-A11, service manual, brief instructions and user manuals JAI CV-A11. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JAI CV-A11.

Similar manuals

A complete manual for the device JAI CV-A11, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JAI CV-A11 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JAI CV-A11.

A complete JAI manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JAI CV-A11 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JAI CV-A11, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JAI CV-A11, that we can find in the current document
3. Tips how to use the basic functions of the device JAI CV-A11 - which should help us in our first steps of using JAI CV-A11
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JAI CV-A11
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JAI CV-A11 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JAI CV-A11?

Use the form below

If you did not solve your problem by using a manual JAI CV-A11, ask a question using the form below. If a user had a similar problem with JAI CV-A11 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)