Manual IBM 09N4076

78 pages 0.88 mb
Download

Go to site of 78

Summary
  • IBM 09N4076 - page 1

     4X/8X/32X CD-ReWritable drive' 1 ...

  • IBM 09N4076 - page 2

    2 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit ...

  • IBM 09N4076 - page 3

    4X/ 8X/ 3 2X I n ter n al R W C D - ROM D r i v e Op t i o n Ki t Us e r ' s G u i d e OP T I O N S by I B M ...

  • IBM 09N4076 - page 4

    Note: Before using this information and the product it supports, be sure to read the information under Appendix E, “Product warranty and notices” on page 2-22. First Edition (February 2000) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MA ...

  • IBM 09N4076 - page 5

    Contents Safety: Read first ................................ i v Registering your option ............................ v About this book ................................ v Part 1: Installation and usage guide ................ 1-1 Part 2: Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Appendix A. Product specifications . . . . . ...

  • IBM 09N4076 - page 6

    Safety: Read first Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Před instalací tohoto produktu si přečtěte příručku bezpečnostních instrukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Ennen kuin asennat tämän tuotteen, lue turvao ...

  • IBM 09N4076 - page 7

    Läs säkerhetsinformationen innan du installerar den här produkten. Registering your option Thank you for purchasing OPTIONS by IBM  . Please take a few moments to register your product and provide us with information that will help IBM to better serve you in the future. Your feedback is valuable to us in developing products and services that ...

  • IBM 09N4076 - page 8

    vi IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit ...

  • IBM 09N4076 - page 9

    Part 1: Installation and usage guide This part of the manual consists of an introduction, installation instructions, and instructions for using and maintaining the CD-RW drive. Introduction This section will give you a description of this option and the software which comes with it, as well as some information you will need before you install the o ...

  • IBM 09N4076 - page 10

     Blank CD-RW disc  Blank CD-R disc  Adaptec Easy CD Creator/DirectCD disc  IBM Option Diskette  Laser Safety Guide for CD-ROMs  Electrical safety booklet Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of purchase. It might be required to receive warranty service. See Appendix D, “He ...

  • IBM 09N4076 - page 11

    System requirements Before you begin installing the drive, be sure your computer meets the following system requirements.  Minimum microprocessor: Intel  Pentium  processor (or the equivalent)  Minimum RAM: 16 MB 4  3.5-inch diskette drive  Available IDE connection  Available internal power connection  Available drive bay ? ...

  • IBM 09N4076 - page 12

    Front view of the drive Refer to the illustration to identify parts that might be referred to in the installation instructions. .1/ Headphone jack This jack provides audio output to the headphones. .2/ Volume control This dial controls the headphone volume. .3/ CD tray This tray is where you load and unload a CD. .4/ Busy indicator This light comes ...

  • IBM 09N4076 - page 13

    .3/ Configuration pins These pins are used to set the drive configuration. .4/ IDE connector This port connects the CD-RW drive to the IDE cable. .5/ DC-power connector This port connects the CD-RW drive to the computer power supply cord. Installing the drive Follow these steps to install the CD-RW drive into your computer. Step 1. Opening the comp ...

  • IBM 09N4076 - page 14

    refer to the documentation that comes with your computer or with the device in question.  Some non-IBM computers support the cable-select setting, where the position of the device on the cable determines whether a device is master or subordinate. See the documentation that comes with your computer to determine if your computer supports this sett ...

  • IBM 09N4076 - page 15

    1. Slide the drive into the bay. Your computer might have specific required procedures for installing storage devices. Refer to the documentation that comes with your computer for further instructions. 2. Align the drive-bay screw holes with the threaded holes in the drive housing or mounting bracket; then thread the screws in loosely to check thei ...

  • IBM 09N4076 - page 16

    Step 7. Completing the hardware installation 1. Be sure that the drive is securely mounted and the connectors are firmly attached. 2. Be sure that the cables do not interfere with the computer cover and do not block the power-supply fan blades or air-flow paths. 3. Reinstall the computer cover. 4. Reconnect all devices and check any devices that mi ...

  • IBM 09N4076 - page 17

    To install the IBM Option Diskette device drivers for Windows 98, Windows 95, Windows 3.x, OS/2 or DOS: 1. Insert the IBM Option Diskette into the diskette drive. 2. Type A:CDSETUP in a command line and press Enter. 3. Click Setup . 4. Follow the on-screen instructions to install the software. 5. Click Exit after software installation completes. 6. ...

  • IBM 09N4076 - page 18

    Using CD-R and CD-RW discs The CD-RW drive can write to both CD-R and CD-RW discs. CD-R discs cannot be erased, but can be used with standard CD-ROM drives and CD players. You can use CD-R discs to record audio tracks, store data, archive files, and copy files from another CD. CD-RW discs can be erased and rewritten, but can be used only with newer ...

  • IBM 09N4076 - page 19

     Do not write on the surface.  Do not place the CD in direct sunlight.  Do not use commercial cleaners to clean the CD.  Do not bend the CD. Caring for the CD-RW drive To protect your CD-RW drive during operation, observe the following precautions.  Remove any CD in the drive before moving the drive.  Do not insert foreign objects ...

  • IBM 09N4076 - page 20

    To load a CD into a vertically mounted CD-RW drive, follow these steps. 1. Press the Eject/Load button. 2. Look at the illustrations and compare them to your loading tray.  If your loading tray looks like the left illustration, insert the CD carefully so that the edges of the CD are underneath the tabs on the loading tray. These plastic tabs cov ...

  • IBM 09N4076 - page 21

    Manually ejecting a CD If you press the Eject/Load button and the tray does not slide out, turn off the computer and straighten a large paper clip to form a tool, as shown in the illustration. The straightened end must extend at least 45 mm (1.8 in.). Insert the extended end into the manual-eject hole on the front of the drive (see “Front view of ...

  • IBM 09N4076 - page 22

    4. Type the title of your disc in the Name Your Disc window. The disc name can be up to 11 characters. 5. If you plan to use data compression software with this disc, click to check the box next to the message Enable compression on this disc . 6. Click Finish in order to start disc formatting. When the disc is finished formatting, the Disc Ready wi ...

  • IBM 09N4076 - page 23

    Making a jewel case insert You can use Easy CD Creator to create a jewel case insert or CD label. When you create a data or audio CD, the Easy CD Creator program creates a jewel case insert using the information in your CD layout, such as CD title, artist name, and song list. To print a jewel case insert or CD label: 1. Click Start --> Programs ...

  • IBM 09N4076 - page 24

    Installation and usage guide (Translate) This part of the manual consists of an introduction, installation instructions, and instructions for using and maintaining the CD-RW drive. Introduction This section will give you a description of this option and the software which comes with it, as well as some information you will need before you install t ...

  • IBM 09N4076 - page 25

     Blank CD-RW disc  Blank CD-R disc  Adaptec Easy CD Creator/DirectCD disc  IBM Option Diskette  Laser Safety Guide for CD-ROMs  Electrical safety booklet Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of purchase. It might be required to receive warranty service. See Appendix D, “He ...

  • IBM 09N4076 - page 26

    Before you begin installing the drive, be sure your computer meets the following system requirements.  Minimum microprocessor: Intel  Pentium  processor (or the equivalent)  Minimum RAM: 16 MB 4  3.5-inch diskette drive  Available IDE connection  Available internal power connection  Available drive bay  One of the followi ...

  • IBM 09N4076 - page 27

    .1/ Headphone jack This jack provides audio output to the headphones. .2/ Volume control This dial controls the headphone volume. .3/ CD tray This tray is where you load and unload a CD. .4/ Busy indicator This light comes on when the drive reads from, writes to, or plays a CD. .5/ Manual-eject hole This hole provides access to the eject mechanism ...

  • IBM 09N4076 - page 28

    Step 1. Opening the computer 1. Turn off the computer and all attached devices. 2. Unplug the power cords for the computer and all attached devices. 3. Remove the cover from the computer. Step 2. Unpacking the drive 1. Before opening the antistatic bag that the drive is packed in, touch it to an unpainted metal surface for at least two seconds. Thi ...

  • IBM 09N4076 - page 29

    Step 4. Setting the configuration jumper The illustration shows the master .1/ setting, the subordinate (or slave) .2/ setting, and the cable-select .3/ setting. Configure the CD-RW drive by placing the jumper over the set of pins corresponding to the setting you chose in “Step 3. Selecting an IDE port.”  If you are configuring the CD-RW dri ...

  • IBM 09N4076 - page 30

    Step 6. Attaching the cables to the drive Connect the cables to the CD-RW drive as follows. 1. If you want to connect the CD-RW drive to your sound adapter or to the sound function on your system board, locate the included audio cables and determine which cable best fits the CD audio-in port on your sound adapter. Connect one end of the selected au ...

  • IBM 09N4076 - page 31

    Step 8. Attaching the faceplates This option package includes two faceplates that conform to the curved design of certain computers. If your computer has a curved design, you can attach one of the included faceplates so that the front of the CD-RW drive matches the exterior cabinet. Choose the faceplate that best fits your computer, and attach it a ...

  • IBM 09N4076 - page 32

    Windows NT 4.0 will automatically detect the presence of the drive. No additional steps are required to activate the device drivers. For optional information about configuring the IBM Option Diskette device drivers for Windows 3.x, DOS, OS/2, Windows 98, and Windows 95, go to Appendix C, “Customizing device driver configuration settings” on pag ...

  • IBM 09N4076 - page 33

    Using the drive This section will give you information on how to handle and care for CDs and your CD-RW drive, how to load CDs into your CD-RW drive, and how to get started using the Easy CD Creator and DirectCD programs. Handling and caring for a CD CDs are high-density media that must be handled with care and kept clean to insure that they remain ...

  • IBM 09N4076 - page 34

    Caring for the CD-RW drive To protect your CD-RW drive during operation, observe the following precautions.  Remove any CD in the drive before moving the drive.  Do not insert foreign objects into the drive.  Do not stack objects on the drive.  Do not remove the drive cover or attempt to service the drive.  Do not operate the drive u ...

  • IBM 09N4076 - page 35

    To load a CD into a vertically mounted CD-RW drive, follow these steps. 1. Press the Eject/Load button. 2. Look at the illustrations and compare them to your loading tray.  If your loading tray looks like the left illustration, insert the CD carefully so that the edges of the CD are underneath the tabs on the loading tray. These plastic tabs cov ...

  • IBM 09N4076 - page 36

    Manually ejecting a CD If you press the Eject/Load button and the tray does not slide out, turn off the computer and straighten a large paper clip to form a tool, as shown in the illustration. The straightened end must extend at least 45 mm (1.8 in.). Insert the extended end into the manual-eject hole on the front of the drive (see “Front view of ...

  • IBM 09N4076 - page 37

    4. Type the title of your disc in the Name Your Disc window. The disc name can be up to 11 characters. 5. If you plan to use data compression software with this disc, click to check the box next to the message Enable compression on this disc . 6. Click Finish in order to start disc formatting. When the disc is finished formatting, the Disc Ready wi ...

  • IBM 09N4076 - page 38

    Making a jewel case insert You can use Easy CD Creator to create a jewel case insert or CD label. When you create a data or audio CD, the Easy CD Creator program creates a jewel case insert using the information in your CD layout, such as CD title, artist name, and song list. To print a jewel case insert or CD label: 1. Click Start --> Programs ...

  • IBM 09N4076 - page 39

    Product registration Thank you for purchasing OPTIONS by IBM  . Please take a few moments to register your product and provide us with information that will help IBM to better serve you in the future. Your feedback is valuable to us in developing products and services that are important to you, as well as in developing better ways to communicate ...

  • IBM 09N4076 - page 40

    32 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit ...

  • IBM 09N4076 - page 41

    Part 2: Appendixes This section includes information on product specifications, how to solve typical problems, how to customize the DOS device driver for this option, and how to obtain help and service. It also includes the product warranty and legal notices. Appendix A. Product specifications This appendix includes the the following information: ? ...

  • IBM 09N4076 - page 42

    Environmental requirements The following table lists the environmental specifications for the CD-RW drive. You can mount the drive vertically or horizontally. Write/Read speeds The following table lists the CD-RW drive write/read speeds for different media. Drive-performance specifications The following table lists the performance specifications of ...

  • IBM 09N4076 - page 43

    The following table summarizes the CD format capabilities of the Easy CD Creator program. Refer to the Adaptec software online users’s guide for the most recent information on CD format capabilities. The CD-RW drive uses the following methods to write files to CDs:  Disc at Once : The drive writes to the entire disc in a single pass; data cann ...

  • IBM 09N4076 - page 44

    multimedia content. CD-I (Mode 2 Form 1 and Mode 2 Form 2) and CD-I Ready 13 This format is used for home entertainment systems. CD-I Bridge This format records a combination of Kodak Photo CDs and Video CDs that can be played on TV set-top players and personal computers. Photo CD (single and multisession) This format records Kodak Photo CDs. Video ...

  • IBM 09N4076 - page 45

    Appendix B. Problem solving Computer problems can be caused by hardware, software, or user error. You might be able to use the information in this section to solve problems yourself, or gather helpful information you can pass on to a service technician. You might also need to refer to your computer, operating-system, or sound-adapter documentation. ...

  • IBM 09N4076 - page 46

    If there are two devices on the IDE port, attach the connector at one end of the cable to the IDE port. If there is a hard disk drive, attach it to the connector at the other end of the cable and attach the CD-RW drive to the middle connector. You cannot format a CD-RW disc. Take the following actions: 1. Verify that your computer has the latest le ...

  • IBM 09N4076 - page 47

    You cannot read from the CD after successfully writing to it. Take the following actions: 1. If you can read the CD in another CD player or you can see previous sessions, the directory information might be damaged on the volume, making it unreadable. Check the Adaptec software online user’s guide for more troubleshooting ideas. 2. You might have ...

  • IBM 09N4076 - page 48

    7. Restart the computer. If the device icon is still not present, check cable connections, device jumper settings, and resolve any existing conflicts. You cannot access the CD-RW drive (DOS and Windows 3.x), or the drive icon (Windows 3.x) does not display. Your CD-RW drive device driver might not be loaded or cannot be found. Before checking the C ...

  • IBM 09N4076 - page 49

    If the device drivers are not present, reinstall them. See the READ.ME file on the IBM Option Diskette for more information. The computer does not recognize the CD-RW drive after the device drivers are loaded (DOS and Windows 3.X). Check for incompatibilities among the CD-RW drive device driver and other device drivers or other hardware in your com ...

  • IBM 09N4076 - page 50

    5. Observe the startup messages and check that the device driver IBMIDECD.SYS loads. When MSCDEX loads, observe the drive letter that the computer assigns to the CD-RW drive. 6. Load a data CD into the CD tray; then wait until the busy indicator is not lit. 7. Attempt to read from the CD by typing dir x : where x is the CD-RW drive letter assigned ...

  • IBM 09N4076 - page 51

    2. The CD might be defective; try another CD. 3. The CD is not ISO-9660 or High Sierra Group (HSG) compatible. Check with your place of purchase. There is no sound from the CD. Take the following actions. 1. Check that you are using an audio CD and not a data CD. 2. Adjust the volume control on the drive. See “Front view of the drive” on page 1 ...

  • IBM 09N4076 - page 52

    Diagnostics The IBM Option Diskette contains a problem-solving diagnostic program for DOS. You must successfully load the CD-RW drive device drivers before starting the diagnostic program. To start the diagnostic program, insert the IBM Option Diskette , type A:CDDIAG at the DOS prompt, and press Enter. Additional help The READ.ME file on the IBM O ...

  • IBM 09N4076 - page 53

    Appendix C. Customizing device driver configuration settings Attention: After you install the IBM Option Diskette , you can use a DOS session in Windows 3.x, DOS, OS/2, Windows 98, and Windows 95 to access the drive as a CD-ROM drive. This section contains optional configuration information for the IBM Option Diskette device drivers for Windows 3.x ...

  • IBM 09N4076 - page 54

    The device driver automatically checks the industry standard primary IDE port (address 1F0, interrupt 14) and secondary IDE port (address 170, interrupt 15). The /P parameter is not needed if your CD-ROM drive is connected to either of these ports. However, if your computer (or IDE adapter) uses different IDE port addresses or interrupts, you must ...

  • IBM 09N4076 - page 55

    CD-ROM can provide data. This parameter is usually not required in most computers. n is a relative timing parameter that depends on processor speed. When the value of n increases, the drive data-transfer rate decreases. Valid values for n are 0 through 99. The default for n is 0, and the /T parameter is not required. /I: n This parameter enables in ...

  • IBM 09N4076 - page 56

    /M: nn This parameter specifies the number of sector buffers for temporary storage of the most recent CD data. For example, to specify 12 sector buffers you would use: C:MSCDEX.EXE /D:IBMCD1ðð /M:12 The CDSETUP program sets this value to 10. The default value for MSCDEX with no /M parameter is 4. You can improve CD-ROM drive performance when you ...

  • IBM 09N4076 - page 57

    /S This parameter instructs MSCDEX.EXE to allow networked computers to share CD-ROM drives. Conserving DOS conventional memory If the CD-ROM drive-support software is loaded in DOS conventional memory (below 640 KB RAM), there might be insufficient memory to run some DOS applications. The CDSETUP program attempts to load the IDE CD-ROM drive device ...

  • IBM 09N4076 - page 58

    Updating the device driver for a DOS network server If you are using the CD-RW drive in a DOS Network server you need to make the following changes: 1. Add the /S parameter to the MSCDEX line in the AUTOEXEC.BAT file. 2. Verify that the MSCDEX line is located after the line that loads the network services (NET START for IBM PC LAN program). 3. Do o ...

  • IBM 09N4076 - page 59

    /M: n Indicates the maximum number of file sectors to be read at a time. The default is eight sectors (/M:8). /K Uses Kanji supplementary volume descriptor. /Q Suppresses messages during initialization. Changing the OS/2 IDE adapter device driver The following IDE device driver is available: BASEDEV=IBM1S5ð6.ADD (for ISA computers) This device dri ...

  • IBM 09N4076 - page 60

    Appendix D. Help and service information See Appendix B, “Problem solving” on page 2-5 before requesting help or service. This section contains information on how to obtain online and telephone technical support. Online technical support Online technical support is available during the life of your product. Online assistance can be obtained thr ...

  • IBM 09N4076 - page 61

    For the support telephone number and support hours by country, refer to the following table or to the enclosed technical support insert. If the number is not provided, contact your IBM reseller or IBM marketing representative. Response time may vary depending on the number and nature of the calls received. Support 24 hours a day, 7 days a week Cana ...

  • IBM 09N4076 - page 62

    Appendix E. Product warranty and notices This section includes product warranty information and legal notices. Warranty statements The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by country. Part 2 is the same for both statements. Be sure to read both the Part 1 that applies to your country and Part 2.  United Stat ...

  • IBM 09N4076 - page 63

    If a Machine does not function as warranted during the warranty period, and IBM or your reseller are unable to either 1) make it do so or 2) replace it with one that is at least functionally equivalent, you may return it to your place of purchase and your money will be refunded. The replacement may not be new, but will be in good working order. Ext ...

  • IBM 09N4076 - page 64

    conversions, or upgrades involve the removal of parts and their return to IBM. A part that replaces a removed part will assume the warranty service status of the removed part. Before IBM or your reseller exchanges a Machine or part, you agree to remove all features, parts, options, alterations, and attachments not under warranty service. You also a ...

  • IBM 09N4076 - page 65

    DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IBM Statement of Warranty Worldwide except Canada, Puerto Rico, Turkey, United States (Part 1 - General Terms) This Statement of Warranty includes Part 1 - General Terms and Part 2 - Country-unique Terms. The terms of Part 2 may replace or modify those of Part 1 . The warranties pr ...

  • IBM 09N4076 - page 66

    WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD. Items Not Covered by Warranty IBM ...

  • IBM 09N4076 - page 67

    IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM's possession or 2) in transit in those cases where IBM is responsible for the transportation charges. Neither IBM nor your reseller is responsible for any of your confidential, proprietary or personal information contained in a Machine which you return to IBM or y ...

  • IBM 09N4076 - page 68

    Operating Environment, improper maintenance by you, or failure caused by a product for which IBM is not responsible. Limitation of Liability: The following is added to this Section: Where IBM is in breach of a condition or warranty implied by the Trade Practices Act 1974, IBM's liability is limited to the repair or replacement of the goods or ...

  • IBM 09N4076 - page 69

    govern this Statement if the warranty service is provided in Albania, Armenia, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Federal Republic of Yugoslavia, Georgia, Hungary, Kazakhstan, Kirghizia, Former Yugoslav Republic of Macedonia (FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia, and Ukraine. The follo ...

  • IBM 09N4076 - page 70

    1. death or personal injury or physical damage to your real property solely caused by IBM's negligence; and 2. the amount of any other actual direct damages, up to the greater of Irish Pounds 75,000 or 125 percent of the charges (if recurring, the 12 months' charges apply) for the Machine that is the subject of the claim or which otherwis ...

  • IBM 09N4076 - page 71

    UNITED STATES OF AMERICA: Warranty Service: The following is added to this Section: To obtain warranty service from IBM, call 1-800-772-2227 . Part 2: Appendixes 2-31 ...

  • IBM 09N4076 - page 72

    Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Subject to IBM’s valid intel ...

  • IBM 09N4076 - page 73

    Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: Microsoft, Windows, and Windows NT are trademarks or registered trademarks of Microsoft Corporation in the United States or other countries or both. Intel and Pentium are trademarks of Intel Corporation in the United States or other ...

  • IBM 09N4076 - page 74

    Electronic emission notices IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte ...

  • IBM 09N4076 - page 75

    Avis de conformité à la réglementation d'Industrie Canada Cet appareil numérique de classe B est conforme à la norme NMB-003 du Canada. European Union - emission directive This product is in conformity with the protection requirements of EU Council Directive 89/366/ECC on the approximation of the laws of the Member States relating to elec ...

  • IBM 09N4076 - page 76

    Union Europea - Normativa EMC 2-36 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit ...

  • IBM 09N4076 - page 77

    ...

  • IBM 09N4076 - page 78

    IBM  Part Number: 09N4076 Printed in U.S.A. ð9N4ð76 ...

Manufacturer IBM Category Computer Drive

Documents that we receive from a manufacturer of a IBM 09N4076 can be divided into several groups. They are, among others:
- IBM technical drawings
- 09N4076 manuals
- IBM product data sheets
- information booklets
- or energy labels IBM 09N4076
All of them are important, but the most important information from the point of view of use of the device are in the user manual IBM 09N4076.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals IBM 09N4076, service manual, brief instructions and user manuals IBM 09N4076. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product IBM 09N4076.

A complete manual for the device IBM 09N4076, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use IBM 09N4076 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of IBM 09N4076.

A complete IBM manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual IBM 09N4076 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the IBM 09N4076, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the IBM 09N4076, that we can find in the current document
3. Tips how to use the basic functions of the device IBM 09N4076 - which should help us in our first steps of using IBM 09N4076
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with IBM 09N4076
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of IBM 09N4076 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning IBM 09N4076?

Use the form below

If you did not solve your problem by using a manual IBM 09N4076, ask a question using the form below. If a user had a similar problem with IBM 09N4076 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)