Manual TP-Link RX-7-248

44 pages 3.35 mb
Download

Go to site of 44

Summary
  • TP-Link RX-7-248 - page 1

    T O A MIXING CONSOLE Operating Instruction Manual Model RX-7-164, RX-7-248, RX-7-328 T O A ELECTRIC CO., LT D. KO B E, JAPAN ...

  • TP-Link RX-7-248 - page 2

    Precautions .................................................. 2 General Description ............................................ 3 Features .................................................. ..... 4 Specifications & Characteristics ............................... 6 Input & Output Specifications ................................ 7 Level Diag ...

  • TP-Link RX-7-248 - page 3

    Precautions 1 . Power Supply Unit (RPS-7) The RPS-7 is separate f ro m the console. I f the power switch on the RPS-7 is turned " o n " without a connection between the RPS-7 and t h e board usin g the accessory cable packed i n the RPS-7, p o w e r is n o t supplied to t he board. The power switch must be "o n " after the conne ...

  • TP-Link RX-7-248 - page 4

    General Description TOA's R X - 7 is a modular 1 6 , 24 or 3 2 input channel, 4 group output, 4 to 8 program output mixing console. It is designed t o meet a wide variety o f requirements in professional sound reinforcement an d recording applications. It is wel l designed to withstand th e rigors of " o n the road" use. Modular cons ...

  • TP-Link RX-7-248 - page 5

    GROUP/FOLDBACK a n d GROUP/ECHO MODULES 1 . AUX INPUT (Group/Foldback Module) an d E CH O I N ( Gro up /E cho Module) are both balanced (transformer-isolated), with Low, Mid and High-EQ provided for bo th types o f inputs. 2. ACCESSORY SEND/RECEIVE jacks a r e located on the rear o f the modules f or inserting signal processing devices. 3 . Group O ...

  • TP-Link RX-7-248 - page 6

    PROGRAM MODULE 1 . Group 1 , 2, 3 and 4 controls p ick up t he signal from t he four group out busses and assign them to the program output. Th e program output i s therefore suitable fo r feeding the signal t o t h e house sound system. 2 . Program On/Off pushbutton determines whether the individual program output signal is t o be f e d to t h e r ...

  • TP-Link RX-7-248 - page 7

    Specifications & Characteristics GENERAL SPECIFICATIONS RX-7-164, RX-7-248 A ND RX-7-328 Frequency Response (Measurement o f source impedance 1 5 0 ohms) +0dB, -0.5dB; 50Hz to 20kHz +0dB, -2.0dB; 20 Hz to 30 k H z Total Harmonic Distortion Les s t ha n 0 .5 % at +4dB* output a t 1kHz Hum and Noise (20Hz to 20kHz, input termination o f 1 5 0 ohm ...

  • TP-Link RX-7-248 - page 8

    Input & Output Specifications **All XLR connectors are floating (balanced) and transformer-isolated. TR S phone jacks ar e unbalanced. Sensitivity is the level required t o produce a nominal output o f + 4 d B (1.23V), or t h e specified nominal output level if other than +4dB. R X - 7 OUTPUT CHARACTERISTICS Connection GROUP O U T 1 — 4 PROGR ...

  • TP-Link RX-7-248 - page 9

    Characteristics Diagrams EQUALIZER CURVES FILTER CURVES Level Diagrams (Fig. 1 ) (Fig. 2) — 8 — ...

  • TP-Link RX-7-248 - page 10

    1 . XLR type INPUT connector i s balanced, transformer-isolated and accepts low impedance sources f r o m -60dB t o + 10dB. P r o p er adjustment o f bot h the I NPUT LEVEL Swi tch and TRIM Knob mak e i t possible to provide the optimum setting fo r each input. 2 . GROUND (G ND ) LIF T Switch is fo r P in 1 , which m akes i t easy to avoid ground l ...

  • TP-Link RX-7-248 - page 11

    1 3 . Ec ho knobs provide for two independent echo mixes. The No. 1 echo k no b mixes t he signal post-fader, but the No. 2 echo kn o b is associated wi th t he Pre-Post fader selector switch. 1 4 . PAN P O T adjusts the relative output level (balance) to the f ou r mixing busses. I t i s operated in conjunction with the group assign pushbuttons to ...

  • TP-Link RX-7-248 - page 12

    Group/Foldback Module (GFM-7) 1 . AUX INPUT connector (XLR typ e ) is balanced, transformer-isolated. The nominal level and impedance are +4dB and 60 0 ohms respectively. 2 . GROUND (GND) LIFT switch i s f or pin 1 , which i s used to avoid ground loops that ar e often ca us ed in connection with other equipment a nd that may induce hum. Sliding t ...

  • TP-Link RX-7-248 - page 13

    1 . ECHO IN co nnector (XLR type ) i s balanced, transformer-isolated. T he nominal level and impedance are +4 dB and 6 00 ohms, respectively. 2 . GROUND (GND) L I F T Switch is f o r pi n 1 , which i s used to avoid ground loops that are often caused i n connection with other equipment a nd that may induce hum. Sliding th e ground lift switch fro ...

  • TP-Link RX-7-248 - page 14

    Ea c h program module incorporates two program output channels (programs A and B) and each program channel can be controlled independently. 1 . PROGRAM OUT PU T B connector (XLR t ype) i s balanced, transformer-isolated. Th e nominal level and impedance are +4dB and 60 0 ohms, respectively. T he program output B signal is derived from o n e o f th ...

  • TP-Link RX-7-248 - page 15

    1 . AIR MONITOR (Ceiling Microphone) inputs, XLR type connectors (L and R) ar e balanced, transformer-isolated. Th e nominal levels and impedances are —70dB and 6 0 0 ohm s, respectively. 2. PHONES OUT jacks (L an d R) ar e unbalanced. T he nominal levels an d impedances are +4dB and 1 0 k ohms, respectively. The jacks provide the signals selecte ...

  • TP-Link RX-7-248 - page 16

    1 . TALKBACK OUT connector (XLR type) i s balanced, transformer-isolated, an d its nominal level and impedance are +4dB and 6 0 0 ohms, respectively. T he talkback output includes the oscillator/pink noise generator signal or talkback m ic input, depending on th e switch status on the m odule. The oscillator/pink noise generator function i s us e d ...

  • TP-Link RX-7-248 - page 17

    1 . DC POWER I NPUT connector accepts D C power fr o m the power supply unit ( RPS-7). The PSM-7 is connected to the RPS-7 w i t h an accessory umbilical cable. T he power switch on the R PS - 7 w i l l n ot turn on with out this connection between the RPS-7 and PS M- 7. 2 . Ground (GND) terminal for the chassis of t h e RX-7. 3 . PHANTOM POWER M A ...

  • TP-Link RX-7-248 - page 18

    Meter Panel ( RXM-7-25, RXM-7-35, RXM-7-43) METER PANEL ( RXM-7-25) 1. Group I/Program 1 VU Meter An illuminated VU meter provides a visual indication of either Group 1 output le v e l (Post Group 1 Master Fader) or Program 1 output l ev el (P o s t Program 1 Master C ontrol), depending on the position o f the a dj a c en t selection switch. 2. V U ...

  • TP-Link RX-7-248 - page 19

    1 0 . VU meter selector switch ( Foldback 1 or Echo 1) 1 1 . Foldback 2/Echo 2 VU meter An illuminated VU meter provides a visual indication of either Foldback 2 out pu t level, (Post Foldback 2 Master Volume Co ntrol) or Ec ho 2 output level (Post Echo 2 Master Volume Control), depending on the position o f the adjacent selector switc h. 1 2. VU m ...

  • TP-Link RX-7-248 - page 20

    METER PANEL ( RXM-7-35) 1 . Group 1 V U Meter (Group 1 output level) 2. Group 2 VU Meter (Group 2 output level) 3. Group 3 V U Meter (Group 3 output level) 4. Group 4 VU Meter (Group 4 output level) 5. Program 1/Program 5 V U Meter An illuminated VU meter provides a visual indication o f either Program 1 output level or Program 5 output level, depe ...

  • TP-Link RX-7-248 - page 21

    1 . Group 1 V U Meter (Group 1 output level) 2. Grou p 2 V U Meter (Group 2 output level) 3. Group 3 VU Meter (Group 3 output level) 4. Group 4 VU Meter (Group 4 output level) METER PANEL ( RXM-7-43) 5. Program 1/ P rogram 5 V U Meter An illuminated VU meter provides a visual indication o f either Program 1 ou t pu t level or Pr o gr a m 5 output l ...

  • TP-Link RX-7-248 - page 22

    1 . AC Fuse The f us e should be replaced with one o f identical value and type. 2. Pilot Lamp 3. Power Switch Pushbutton alternately s w itches AC p ow er o n and of f. 4. D C output connector With the accessory umbilical cable, t he DC ou tp ut i s connected to the PSM -7 (Power Supply Module). 5. Ground Terminal 6. A C Inlet Plug an accessory AC ...

  • TP-Link RX-7-248 - page 23

    General Information o n using th e mixing console * Impedance Generally speaking, there ar e two rules to follow when connecting equipment o utp uts to the inputs o f other equipment. 1 . T ry to properly match the impedances o f the outputs an d i nputs. 2. Connect low impedance outputs to hi g h im pedance input. T h e above rules about impedance ...

  • TP-Link RX-7-248 - page 24

    * Ground loops AC ground i s provided to the RX-7 and al l associated equipment, an d this may cause an increase in h u m noise if care is not taken in connecting other equipment to the mixer. This is because a ground loop is m ade through the shields of th e connection cable and the AC line as shown in F i g. 1 5 , increasing hum noise. To solve t ...

  • TP-Link RX-7-248 - page 25

    The RX-7 i s a sophisticated mixer with many functions. Details on important functions a r e shown below in order f o r you to get the best operation and performance an d al s o t o avoid mistakes in operation. * Phantom Power Swi tc h Th e switch on th e front panel o f b o t h IPM-7 and PHM-7 provides f or 48 V DC phantom powering for condenser m ...

  • TP-Link RX-7-248 - page 26

    The tri m control changes the negative feedback volume, so that the ga in o f the head amp can al so be changed. T HI S FUNCTIONS T O YIELD TH E B E S T COMBINATION OF MAXIMUM HEADROOM AND MINIMUM NO IS E CHARACTERISTICS. The level in d ications (—60dBm, —40dBm a n d — 20dBm) of t he i n pu t level switch are nominal levels when t he trim con ...

  • TP-Link RX-7-248 - page 27

    * Equalizers The RX-7 equalizers provide lo w and hig h frequency shelving and mid-range peaking, both boost a nd attenuation. T h e m id-range E Q center frequency c a n b e s e t a t a ny frequency between 200Hz a nd 5kHz w it h a continuously variable frequency knob. F i g. 1 9 indicates each instrument a nd frequency band. Th e equalizer operat ...

  • TP-Link RX-7-248 - page 28

    INSTRUMENT EQUALIZATION CHART Acoustic guitar Electric guitar Ba s s guitar Human voice Piano (Acoustic) Piano (Electric) Organ Violin Brass in st r u m ents Bass d r um Snare dr u m Tom Tom Floor Tom Hi Hat Cymbal overhead Talk Box Bass strings resonate between 7 0 to 120Hz, b od y around 300Hz. Avoid boosting these to stop feedback. 3kHz and 5kHz ...

  • TP-Link RX-7-248 - page 29

    * Equalizer IN/OUT Sw it ch Precise equalizer adjustment c a n b e ma de w hile comparing th e equalized sound ef fe c t wit h the flat sound by use o f the Equalizer IN/OUT switc h. *Foldback 1, 2 an d Echo 1 , 2 Th e block diagram indicates the overall signal f lo w of th e FB and Echo circuits. The F B circuit i s basically designed t o derive t ...

  • TP-Link RX-7-248 - page 30

    * R X - 7 Signal Flow Th e overall signal flow of t he RX-7, f r o m input to output, i s shown below. (Fig. 21) — 29 — ...

  • TP-Link RX-7-248 - page 31

    *Air Monitor (Ceiling Microphones) In some cases t he mixer control roo m i s independent from th e hall requiring sound reinforcement, but the mixer operator must monitor the sound in the hall for mixer operation. F or this purpose, air monitor (ceiling m icrophones) inputs are provided o n the phones module and incorporate 4 8 V D C phantom power ...

  • TP-Link RX-7-248 - page 32

    Portable Entertainment Sound Reinforcement Set-Up TOA's R X -7 consoles are designed to help out when you're out on th e road. We're sure you'll find j u s t the r ig ht set-ups f o r each show, but we w anted to s how o ne wa y i t migh t be done. Th e balanced, low-impedance connectors o n the RX-7 can handle t he widest possi ...

  • TP-Link RX-7-248 - page 33

    Multi-Track Recording or Track-Down The TOA RX - 7 series of mixing consoles allows better recordings as w ell a s better concerts. F or multi-track recording, direct outputs o n ea ch input channel can be connected to multi-channel recorder inputs. T here are further optional connections, such as monitoring to a control room or to the performers, ...

  • TP-Link RX-7-248 - page 34

    How t o remove modules 1 . Remove the armrest from th e cabinet in the following manner. *Pu t both hands under the armrest and lift it straight up to remove. (Fig. 24) 2. Loosen t he t wo captive screws on th e front o f the meter panel and lif t panel straight up. Module Replacement (Fig. 25) — 33 — ...

  • TP-Link RX-7-248 - page 35

    (Fig. 26) 3 . Rem ove the tw o binding screws on each module. Put your fingers i n the two holes o n t h e to p a nd bottom o f th e module and lift t he module straight up to remo ve it from the cabinet. * When putting the module back into the cabinet, align it along th e guides of the frame, making the connector o n the rear o f the module mate w ...

  • TP-Link RX-7-248 - page 36

    1 . Input M odules (IPM-7) 2 . Group/Foldback Modules (GFM-7) 3 . Group/Echo Modules (GEM-7) 4. Program Modules (PGM -7) 5 . Phones Module (PHM-7) 6 . Talkback Module (TBM-7) 7 . Power Supply Module (PSM-7) 8 . VU Meters for Group and Program Outputs (Switchable) (Fig. 27) RX-7-164 APPEARANCE Dimensional Diagrams 9 . VU Meters fo r Foldback and Ech ...

  • TP-Link RX-7-248 - page 37

    1 . Input M odules (IPM-7) 2 . Group/Foldback Modules (G FM-7) 3 . Group/Echo Mo du le s (G EM-7) 4 . Program Modules (PG M-7 ) 5 . Phones Module (PHM -7) 6 . Talkback Module (TBM-7) 7 . Power Supply Module (PSM-7) 8 . VU Meters for Group Outputs 9 . VU Meters fo r Program Outputs ( 1— 5 , 2—6, 3—7, 4 —8 Switchable) 1 0 . VU Meter fo r Fold ...

  • TP-Link RX-7-248 - page 38

    RX-7-328 APPEARANCE (Fig. 29) 1. 2. 3. 4. 5. 6. 7. 8. 9. Input Modules (IPM-7) Group/Foldback M odules (GFM-7) Group/Echo Mo du l es (G EM-7) Program Modules (PGM-7) Phones Module (PHM-7 ) Talkback Module (TBM-7) Power Supply Module (PSM-7) VU Meters fo r G roup Outputs VU Meters fo r Program Outputs (1 —5 , 2—6, 3—7, 4—8 Switchable) 10. 11 ...

  • TP-Link RX-7-248 - page 39

    1. 2. 3. 4. 5. 6. 7. 8. Armrest Bus Chassis Wood Sid e Panel Metal Si d e Panel Main Rear Panel Meter Panel VU Meters f or Group an d Program Outputs (Switchable) VU Meters f or Foldback and Echo Outputs (Switchable) 9. 10. 11. 12. 13. 14. 15. VU Meter fo r C ue and Talkback (Switchable) Meter S i d e Pa nel Foldback Outputs Group Outputs Echo Send ...

  • TP-Link RX-7-248 - page 40

    RXM-7-35 APPEARANCE (Fig. 31) 1. 2. 3. 4. 5. 6. 7. 8. Armrest Bus Chassis Wood Si d e Panel Metal S i d e Panel Main Rea r Panel Meter Panel VU Meter fo r Group Outputs VU Meter fo r Program Outputs (1 — 5, 2—6 , 3—7, 4 —8 Switchable) 9. 10. 11. 12. 13. 14. 15. 16. VU Meter f or Foldback and Echo Outputs (Switchable) VU Meter for Cue and Ta ...

  • TP-Link RX-7-248 - page 41

    RXM-7-43 APPEARANCE 1 . Armrest 2. Bus C hassi s 3 . Wo od S i d e Panel 4. Metal Side Panel 5 . Main Re ar Panel 6 . Meter Panel 7 . VU Meters f o r Grou p Outputs 8 . VU Meters fo r Program Outputs (1—5, 2—6, 3—7, 4— 8 Switchable) 9 . VU Meter f o r Foldback 1 1 0 . VU Meter for Foldback 2 1 1 . VU Meter f o r Echo 1 1 2 . VU Meter fo r E ...

  • TP-Link RX-7-248 - page 42

    RPS-7 APPEARANCE (Fig. 33) 1 . AC F use Holder 2. Power On/Off Indicator 3 . Power On/Off Switch 4. D C Power Output Connector 5 . Ground Ter min al 6 . AC Inlet — 41 — ...

  • TP-Link RX-7-248 - page 43

    Block Diagram (Fig. 34) — 42 — ...

  • TP-Link RX-7-248 - page 44

    T O A ELECTRIC CO., LT D. KO B E , JAPAN Printed i n Japan 133-02-476-20 ...

Manufacturer TP-Link Category Music Mixer

Documents that we receive from a manufacturer of a TP-Link RX-7-248 can be divided into several groups. They are, among others:
- TP-Link technical drawings
- RX-7-248 manuals
- TP-Link product data sheets
- information booklets
- or energy labels TP-Link RX-7-248
All of them are important, but the most important information from the point of view of use of the device are in the user manual TP-Link RX-7-248.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TP-Link RX-7-248, service manual, brief instructions and user manuals TP-Link RX-7-248. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TP-Link RX-7-248.

Similar manuals

A complete manual for the device TP-Link RX-7-248, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TP-Link RX-7-248 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TP-Link RX-7-248.

A complete TP-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TP-Link RX-7-248 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TP-Link RX-7-248, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TP-Link RX-7-248, that we can find in the current document
3. Tips how to use the basic functions of the device TP-Link RX-7-248 - which should help us in our first steps of using TP-Link RX-7-248
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TP-Link RX-7-248
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TP-Link RX-7-248 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TP-Link RX-7-248?

Use the form below

If you did not solve your problem by using a manual TP-Link RX-7-248, ask a question using the form below. If a user had a similar problem with TP-Link RX-7-248 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)