English dropdown-ico

Manual QSC UF-3

14 pages 0.25 mb
Download

Go to site of 14

Summary
  • QSC UF-3 - page 1

    11 UF-3 UF-3 UF-3 UF-3 UF-3 Universal Universal Universal Universal Universal Filter Filter Filter Filter Filter *TD-004031-00* *TD-004031-00* Rev. A Owner’ s Manual ...

  • QSC UF-3 - page 2

    ...

  • QSC UF-3 - page 3

    1 I. DESCRIPTION The UF-3 is an embedded dual-channel universal filter accessory for use with select QSC power amplifiers. Compatible amplifier models and lines, both current and discontinued, include: • All PLX, two-channel CX, and two-channel DCA models (with a BSC-3 or BSC-5 BusCard installed) • All four-channel CX and DCA models (with a BSC ...

  • QSC UF-3 - page 4

    2 III. PROGRAMMING THE UF-3 The UF-3 circuit board has six 3-pin headers and four SIP resistor network sockets (see Figure 2). All are used for programming the module. The circuitry for the two channels is identical, so the headers and sockets are divided between them: those designated by a three-digit number starting in a “ 1 ” (headers J101, ...

  • QSC UF-3 - page 5

    3 Programming the High-Pass Filter and CD Horn Equalization To use either the high-pass filter or the constant-directivity horn equalization, or both, set the jumper on Jx02 across pins 2 and 3, which are the lower two pins on their header. If, however, you do not wish to use either one and want to bypass them instead, set the jumper across pins 1 ...

  • QSC UF-3 - page 6

    4 IV . TYPICAL APPLICA TIONS Subsonic Filter Subsonic filters are commonly used in sound installations to filter out rumbles and other inaudible or unwanted low frequency signals and to protect speaker drivers. Vented speaker enclosures in particular often exhibit a phenomenon in which the acoustical damping on the driver(s) drops at extremely low ...

  • QSC UF-3 - page 7

    5 Ultrasonic Filter An ultrasonic filter is useful for minimizing RF interference, oscillations, leakage or aliasing from digital devices, and other signals that are too high in pitch to hear but may wreak havoc in an amplifier system. Program settings: 1. Set the jumper on Jx01 to enable the low-pass filter (across pins 2 and 3). 2. Set the jumper ...

  • QSC UF-3 - page 8

    6 2-Way Active Crossover This configuration routes the frequencies below a particular frequency to amplifier Channel 1, which shall drive the low-frequency speakers, and the frequencies above to Channel 2, which shall drive the high-frequency speakers. Using the UF-3 as a crossover requires that you drive both amplifier inputs with the same full-ba ...

  • QSC UF-3 - page 9

    7 Ch. 2 Ch. 1 UF-3 PowerLight 1.6 HVX Ch. 2 Ch. 1 UF-3 PowerLight 3.4 (parallel mode) Ch. 2 Ch. 1 UF-3 PowerLight 4.0 (bridged mode) Ch. 1: Ch. 2 LP @ 150 Hz; HP @ 20 Hz Bypassed UF-3: Subwoofer Ch. 1: Ch. 2 LP @ 1000 Hz; HP @ 150 Hz LP @ 1000 Hz; HP @ 150 Hz UF-3: W oofers Ch. 1: Ch. 2 LP @ 5 kHz; HP @ 1000 Hz LP @ 20 kHz; HP @ 5 kHz UF-3: Mids &a ...

  • QSC UF-3 - page 10

    8 Tools and materials you will need: Soldering iron Desoldering iron or other suitable desoldering equipment Phillips screwdriver Wire cutters Rosin-core solder CAUTION: • Do not use desoldering braid because it may damage the solder pads on the BusCard or input board, and it also might not adequately remove solder. • The UF-3 contains active c ...

  • QSC UF-3 - page 11

    9 Continue preparing the PC board by removing solder from all 22 in-line socket holes. Once this is done, you are ready to install the UF-3. With the input panel facing you and the component side of the UF-3 board facing away from you, carefully insert the header pins of the UF-3 fully into the socket holes. Turn the assembly over and solder the UF ...

  • QSC UF-3 - page 12

    10 VII. TECHNICAL ASSIST ANCE & SERVICE Servicing your QSC product requires a trained and qualified technician. There are no user serviceable components inside, and the danger of electric shock exists. Additionally, some of the components are QSC-specific parts that require QSC replacements. Comprehensive service manuals for most models are ava ...

  • QSC UF-3 - page 13

    ...

  • QSC UF-3 - page 14

    12 QSC Audio Products, Inc. 1675 MacArthur Blvd., Costa Mesa, California 92626 USA Tel: +1 714 754-6175 Fax: +1 714 754-6174 Web: www.qscaudio.com ...

Manufacturer QSC Category Musical Instrument

Documents that we receive from a manufacturer of a QSC UF-3 can be divided into several groups. They are, among others:
- QSC technical drawings
- UF-3 manuals
- QSC product data sheets
- information booklets
- or energy labels QSC UF-3
All of them are important, but the most important information from the point of view of use of the device are in the user manual QSC UF-3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals QSC UF-3, service manual, brief instructions and user manuals QSC UF-3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product QSC UF-3.

Similar manuals

A complete manual for the device QSC UF-3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use QSC UF-3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of QSC UF-3.

A complete QSC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual QSC UF-3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the QSC UF-3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the QSC UF-3, that we can find in the current document
3. Tips how to use the basic functions of the device QSC UF-3 - which should help us in our first steps of using QSC UF-3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with QSC UF-3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of QSC UF-3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning QSC UF-3?

Use the form below

If you did not solve your problem by using a manual QSC UF-3, ask a question using the form below. If a user had a similar problem with QSC UF-3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)