Manual Remington r300

72 pages 6.38 mb
Download

Go to site of 72

Summary
  • Remington r300 - page 1

    POWDER ACTUATED TOOL MANUFACTURERS´ INSTITUTE INC. ™ Operating Instructions Read all instructions and warnings found in this manual and on power load packaging before operating your powder actuated tool. This manual should always ac- company the tool and be transferred with it upon change of ownership. IMPORT ANT : REMINGTON R300 S F ® Model R3 ...

  • Remington r300 - page 2

    2 1 19586 S F REMINGTON R300 S F Index W arning: Safety Precautions ............................................ 3-1 1 Why A Fastener Holds .........................................................12 Selecting Fasteners and Power Loads ................................ 13 Operation .................................................................... ...

  • Remington r300 - page 3

    3 1 19586 W arning: Safety Precautions The following pages contain detailed warnings, cautions, and rules of safe operation. Read carefully and become familiar before operating to avoid serious injury . We expressly disclaim any liability for any injury to persons or damage to property which result from your failure to take the precautions containe ...

  • Remington r300 - page 4

    4 1 19586 5. AL W A YS make sure the work area is clean from loose material and debris. 1. NEVER place your hand over the muzzle. Accidental dis- charge can cause serious injury . HANDLING THE TOOL 2. NEVER place your finger on the trigger until the muzzle of the tool is against the work surface. 4. AL W A YS clear the work area on all sides and p ...

  • Remington r300 - page 5

    5 1 19586 4. NEVER carry or pass a loaded powder actuated tool. NEVER point a powder actuated tool at anyone. 3. AL W A YS store UNLOADED powder actuated tool and power loads in a locked container . Keep power loads of different power levels in separate containers. 5. If the tool is dropped, inspect for damage and repair it before continuing to wor ...

  • Remington r300 - page 6

    6 1 19586 7. An operator taking medi- cation should take extra precautions while handling the tool. NEVER drink al- coholic beverages or take medications which impair your vision, balance, or judgement before using a powder actuated tool. KNOW YOUR F ASTENING BASE MA TERIAL 1. AL W A YS know the thickn ess an d type of ba se mat erial into which yo ...

  • Remington r300 - page 7

    7 1 19586 3. NEVER make fastenings in spalled or cracked areas. 2. NEVER attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel. Materials of this type tend to shatter and create hazard from flying particles. 4. NEVER drive power fasteners into thin ...

  • Remington r300 - page 8

    8 1 19586 7. DO NOT drive power fasteners into steel base material less then 3/16" thick, within 2" of a weld, within 1/2" of the edge, or within 1" of another power fastener . 3" 3" 3" 6. DO NOT drive power fasteners into concrete less than three times as thick as the intended power fastener penetration, within 3 ...

  • Remington r300 - page 9

    9 1 19586 WA TER S F 3. AL W A YS use the spall shield when driving directly into concrete or steel. AL W A YS wear eye protection. 4. NEVER use a powder actuated tool in an explosive or flammable atmosphere or when non-sparking tools are required. POWER LOADS AND POWER F ASTENERS 1. NE VE R le av e u nfir ed po we r l oad s on floo rs or wo rk ...

  • Remington r300 - page 10

    10 1 19586 1 2 3 4 5 6 7 8 9 10 11 12 1 22 L E K C I N B R A S S C A L I B E R POWER LOADS ONLY NOTE: Failure to start with the lowest power level can result in overdrive condition and will re- sult in damage to tool (see page 13). Start 1 GRAY 3 GREEN 4 YELLOW 2 BROWN Safety Precautions 2. R e mi n g to n ® Po wer Loa ds are ava ila ble in fou r ...

  • Remington r300 - page 11

    1 1 1 19586 7. NEVER use common nails or other materials as fasten- ers. Remington ® Power Fasteners are manufactured from special steel and heat treated to produce a very hard, yet ductile, fastener . 9. AL W A YS insert the power fastener first, then the power load. If work is interrupted for any reason, AL WA YS remove the power load before re ...

  • Remington r300 - page 12

    12 1 19586 WHY A POWER F ASTENER HOLDS IN CONCRETE Th e com pre ssi on bo nd o f the con - cr ete to th e pow er f as ten er ac cou nts fo r the maj ori ty of the ho ldi ng pow er . Th e pow er fa st ene r dis pl ace s the con - cr ete w hic h tri es to re tur n to i ts orig ina l fo rm cau si ng a s qu eez ing e ff ect. Ma xi mu m hol di ng po wer ...

  • Remington r300 - page 13

    13 1 19586 F ASTENING INTO CONCRETE The proper power fastener length can be determined by adding the thickness of the material to be fastened and the amount of power fastener that will actually penetrate the concrete. The concrete must be three times as thick as the intended power fastener penetration. In most cases, penetration should be ap- proxi ...

  • Remington r300 - page 14

    14 1 19586 S F 489.004 S F 489.004 2. Gras p muzzle and sli de bar rel forwa rd rapidl y until it st ops. This sets piston int o firin g posi tion and o pens t he c hamber . 4. Select the proper Remington ® Power Load (see Application Chart on pages 20 and 21) and insert into the chamber until it stops. NOTE: Failure to start with the lowest powe ...

  • Remington r300 - page 15

    15 1 19586 S F 489.004 S F S F S F 90˚ S F 5. Push barrel into housing to the closed position. 6. Place the muzzle of tool perpendicular to work surface without tilting the tool. Push tool against work surface until sliding action of barrel stops. 7. Before squeezing trigger , rotate safety ON/OFF switch to the SAFETY OFF position. Squeeze trigger ...

  • Remington r300 - page 16

    16 1 19586 CARE OF YOUR R300 Clean your R300 after each day’ s use. Clean chamber with accessory wire brush, part number 056485 (Not included with tool). Apply good quality penetrating lubricant spray (such as WD-40) sparingly and wipe dry . NOTE: The labor regulations of many states require that the operator of this tool on a job site be thoroug ...

  • Remington r300 - page 17

    17 1 19586 1 5 4 8 17 16 7 6 9 3 2 10 18 1 1 13 12 20 15 14 21 19 Key No. Part No. Description Qty . 1 300001 Handle Screw 2 2 3001 10 Handle 1 3 300101 Safety Switch 1 4 300103 Lock W asher 1 5 300104 Safety Switch Screw 1 6 300105 T rigger 1 7 300106 T rigger Spring 1 8 300107 T rigger Lock Nut 1 9 300108 T rigger Screw 1 10 300201 Receiver Stop ...

  • Remington r300 - page 18

    18 1 19586 3. T o assemble, push piston (E) all the way into barrel (B) using a screwdriver (G). Slide the barrel assembly (B) into the receiver (D). T urn barrel (B) to line up tang slot (F) with tang (C). Insert tang (C) into tang slot (F). Firmly tighten knurled tang nut (A). 1. Un sc re w kn urle d ta ng n ut (A ). S lid e b arre l a sse mbly ( ...

  • Remington r300 - page 19

    19 1 19586 PROBLEM Piston hangs out of muzzle. Overdriven fas- tener . Piston jammed. Expended load will not extract. Reduction or loss of power T ool does not completely de- press. POSSIBLE CAUSE T ool overdriven. Pist on not proper ly asse mbled in rela - tion to barrel screw . Broken piston. Excessive power . Overdriving of fas- tener (see above ...

  • Remington r300 - page 20

    20 1 19586 PROBLEM T ool does not fire. Opening and closing of bar- rel or pushing down on the tool, etc. is not smooth but is rough or binds. POSSIBLE CAUSE Failure of tool to depress com- pletely . Dirt build-up on breech not allow- ing proper pen- etration of firing pin. Safety Switch is in ON position Lack of proper cleaning. REMEDY See data l ...

  • Remington r300 - page 21

    21 1 19586 IMPORT ANT • Recommended for use with Remington ® power loads and power fasteners. • If power fastener goes below the top surface of the board, use penetrating control disc (see illustration below) or wash- ered SPW-type power fasteners. • Operators and bystanders must AL WA YS wear goggles and ear protection which meet or exceed ...

  • Remington r300 - page 22

    22 1 19586 T echnical Service Y ou may have further questions about assembling, operating, or maintaining this product. If so, you can visit our T echnical Service web site at www .desatech.com or contact our T ech- nical Service Department at 1-800-858-8501 (English Only). Y ou may also write to: DESA Power T ools™ P .O. Box 90004 Bowling Green, ...

  • Remington r300 - page 23

    23 1 19586 Parts Centrals Ray’s Portable Heater Service 3191 Myers Road Camino, CA 95709-9550 530-644-7716 T ool & Equipment Service Solutions, LLC 5 Manila Drive Hamden, CT 06514-0322 203-248-7553 1-800-397-7553 Grainger Parts Operations 1657 Shermer Road Northbrook, IL 60062-5362 708-498-5900 1-800-323-0620 www .grainger.com Portable Heater ...

  • Remington r300 - page 24

    24 1 19586 Limited W arranty DESA Power T ools™ warrants the Remington ® Model R300 against defects in materials and workmanship for a period of one (1) year (90 days for reconditioned unit) from the date of purchase. The bill of sales or proof of purchase must be pre- sented at the time a claim is made under this warranty . If within one (1) ye ...

  • Remington r300 - page 25

    25 1 19586 REMINGTON R300 S F POWDER ACTUATED TOOL MANUFACTURERS´ INSTITUTE INC. ™ ® Modelo R300 Instrucciones de operación Antes de operar su herramienta accionada con pólvora lea las instrucciones y advertencias de este manual y las del paquete de carga explosiva. Este manual debería siempre acompañar a la herramienta y ser transferido co ...

  • Remington r300 - page 26

    26 1 19586 S F REMINGTON R300 S F El Índice ADVERTENCIA: Precauciones de seguridad ............... 27-35 ¿Porque Un Sujetador De Potencia Sostiene? ................... 36 Selección de los sujetadores de potencia y de las cargas explosivas ................................................... 37 Operación .......................................... ...

  • Remington r300 - page 27

    27 1 19586 ? ? S F S F 489.004 S F D E FEC TIVE DEFECTUOSO ADVERTENCIA: Precauciones de Seguridad L as p á gi n a s si g ui e nt es co nt i en e n ad v er te n ci a s, p r ec au c io n es y r e - g la s d e ta l l ad a s p a ra un a o p er ac i ón se g ur a . L éa l as cu i da do s am e nt e y f a mi l ia rí c es e a n te s d e o pe r ar pa r a ...

  • Remington r300 - page 28

    28 1 19586 S F S F S F S F S F Precauciones de Seguridad 5. SIEMPRE asegúrese que el área de trabajo esté limpia de materiales sueltos y desechos. MANIPULACIÓN DE LA HERRAMIENT A 4. Despeje SIEMPRE el área de trabajo en todo el contorno y coloque en los sitios de trabajo las señales de advertencia apropiadas. 2. NU NC A co loq ue sus de dos e ...

  • Remington r300 - page 29

    29 1 19586 P O W E R L O A D S P O W E L O A D S F S F S F S F S F S F S F Precauciones de Seguridad 4. NUNCA lleve o pase la herramienta accionada con pólvo- ra cuando esté cargada. NUNCA apunte la herramienta accionada con pólvora a ninguna persona. 3. Guarde la herramienta accionada con pólvora y las cargas en un contenedor asegurado bajo ll ...

  • Remington r300 - page 30

    30 1 19586 ? ? ? Precauciones de Seguridad 7. Un operador que esté tomando medicamentos debería tomar precaucio- nes adicionales cuando maneje la herramienta. Cuando vaya a usar la herramienta accionada con pólvora NUNCA ingiera be- bidas alcohólicas ni tome medicamentos que dismi- nuyan su visión, equilibrio o juicio. CONOZCA EL MA TERIAL DE ...

  • Remington r300 - page 31

    31 1 19586 S F S F HIERRO FUNDIDO VIDRIO S F S F S F Precauciones de Seguridad 3. NUNCA realice sujeciones en zonas fragmentadas o agrietadas. 2. NUNCA trate de clavar los sujetadores de potencia en materiales muy duros o frágiles incluidos pero no limitados a hierro fundido, vidrio, baldosa, piedra, ladrillo o acero endurecido. Materiales de este ...

  • Remington r300 - page 32

    32 1 19586 90˚ S F NO S F YES S F SÍ Precauciones de Seguridad 7. NO clave los sujetadores de potencia en materiales a base de acero que tengan menos de 5 mm (3/16 pulg.) de espesor , o en el intervalo de 51 mm (2 pulg.) de una suelda, o 13 mm (1/2 pulg.) del filo o 25,5 mm (1 pulg.) de otro sujetador de potencia. 76mm 76mm 76mm 6. NO clave los ...

  • Remington r300 - page 33

    33 1 19586 30 S F S F Escudo Contra Esquirlas S F WA TER S F AGUA Precauciones de Seguridad 3. Use SIEMPRE el escudo contra esquirlas cuando clave directamente en concreto o en acero. SIEMPRE use pro- tección visual. 4. NUNCA use la herramienta accionada con pólvora en una atmósfera explosiva o inflamable o cuando se requieran herramientas que ...

  • Remington r300 - page 34

    34 1 19586 3. NUNCA use las cargas explosivas en armas de fuego. 5. Una persona que no distingue bien los colores debe tener mayor precaución para evitar que se mezclen cargas ex- plosivas que tengan diversos niveles. 4. En el mismo bolsillo o contenedor NUNCA transporte los sujetadores de potencia u otros objetos duros con las cargas explosivas. ...

  • Remington r300 - page 35

    35 1 19586 2 1 UNLOAD S F DESCARGA 1 2 LOAD S F CARGA 7. NUNCA use clavos comunes u otros materiales como su- jetadores. Los sujetadores Remington ® de Potencia están fabricados con un acero especial y tienen un tratamiento térmico lo cual produce sujetadores muy duros y a la vez dúctiles. 8. NUNCA saque una carga de la cámara usando una palan ...

  • Remington r300 - page 36

    36 1 19586 ¿PORQUÉ UN SUJET ADOR DE POTENCIA SE SOSTIENE EN EL CONCRET O? La adhesión por compresión del co ncr eto ha cia el su jet ado r de po- te nci a ex pli ca la may orí a d el pod er de s uje ció n. El su jet ado r de pote nci a de spl aza a l c oncr eto el cu al t ien de a vo lve r a su f or ma or igi nal o cas ion an- do un ef ec to ...

  • Remington r300 - page 37

    37 1 19586 SUJECIÓN EN CONCRETO L a l o ng i t ud a pr o p ia d a d e l s u j et a d or d e p o te n c ia p u e de d e t er m i n a r se a ñ a di e n do a l e s pe s o r de l m at e r i al a se r s uj e t a do , l a lo n g i - t u d d el su j e t ad o r d e p ot e n c ia qu e r e al m e n te p en e tr a e n e l c o nc r et o . El e s p es o r de ...

  • Remington r300 - page 38

    38 1 19586 S F 489.004 S F 489.004 S F Operación 2. Sujete la boca del cañón y deslice rápidamente el cañón hacia adelante hasta que tope. Esto coloca al pistón en posición de disparo y abre la cámara. 4. Seleccione la carga explosiva Remington ® apropiada (V ea la T abla de utilización en las páginas 44 y 45) e insértela en la cámara ...

  • Remington r300 - page 39

    39 1 19586 Seguridad AP AGADA S F 489.004 S F S F S F 90˚ S F S F Operación 5. Empuje el cañón hacia la carcasa a la posición cerrada. 6. Co loq ue la bo ca del cañ ón pe rpe ndic ula r a la sup erfi cie de tr aba jo si n in cli nar la herr ami ent a. E mpuj e la her rami ent a co ntr a l a sup erfi ci e d e t ra baj o d es liz ánd ol a h ...

  • Remington r300 - page 40

    40 1 19586 30 S F WA TER S F AGUA CUIDADO DE SU R300 Limpie su R300 luego de cada uso diario. Limpie la cámara con un cepillo de alambre que viene como accesorio, número de parte 56485 (No se incluye con la herramienta). Aplique un poco de pulverizador lubricante y penetrante de buena calidad (como el WD-40) y séquelo con un paño. NOT A: los re ...

  • Remington r300 - page 41

    41 1 19586 1 5 4 8 17 16 7 6 9 3 2 10 18 1 1 13 12 20 15 14 21 19 Nº Nº clave de parte Descripción Cantidad 1 300001 T ornillo del mango 2 2 3001 10 Mango 1 3 300101 Interruptor de seguridad 1 4 300103 Arandela de seguridad 1 5 300104 T ornillo del interruptor de seguridad 1 6 300105 Gatillo 1 7 300106 Resorte del gatillo 1 8 300107 Contratuerca ...

  • Remington r300 - page 42

    42 1 19586 S F A S F B D S F B C F B C A S F D B 1. Desenrosque la tuerca moleteada de la lengüeta (A). Deslice hacia fuera el conjunto cañón (B) y retire la lengüeta (C), luego retire el conjunto cañón (B) del recibidor (D). ADVERTENCIA: NUNCA desarme, cambie el cañón, limpie, ensamble una herramienta activada con pólvora cuan - do esté ...

  • Remington r300 - page 43

    43 1 19586 PROBLEMA El pistón cuelga fuera de la boca del cañón. Su jet ado r cla va- do en ex ce so. P is t ó n a t as c a do . No se extrae la carga utilizada. Reducción o pérdida de po- tencia. No se puede presionar com- pletamente a la herramienta. CAUSA PROBABLE Herramienta im- pulsada excesiva- mente. El pistón no está bien ensamblado ...

  • Remington r300 - page 44

    44 1 19586 PROBLEMA La herramienta no dispara. E l ab r ir y c er r a r del cañón o empujar hacia a ba j o e n la he - rramienta, etc. no es suave s in o d u ra o s e r em u er d e . CAUSA PROBABLE No es posible pre- sionar completa- mente a la herra- mienta. La suciedad acu- mula da en la re cá- mara no p ermi te la penetración apro- piad a de ...

  • Remington r300 - page 45

    45 1 19586 IMPORT ANTE • Recomendado para usar con cargas explosivas y sujetado- res de potencia Remington ® . • Si el sujetador de potencia penetra por debajo de la super- ficie superior de la tabla, use el disco de control de pene- tración (vea la ilustración más abajo) o use sujetadores de potencia tipo SPW con rodela incorporada. • L ...

  • Remington r300 - page 46

    46 1 19586 Servicio Técnico Usted puede tener más preguntas sobre cómo ensamblar , utilizar o mantener este producto. Si es así, usted puede visitar nuestro sitio Web de servicio técnico en www.desatech.com o llamar al departamento de servicio técnico al 1-800-858-8501 (sólo en inglés). Usted puede también escribir a: DESA Power T ools™ ...

  • Remington r300 - page 47

    47 1 19586 Ray’s Portable Heater Service 3191 Myers Road Camino, CA 95709-9550 530-644-7716 T ool & Equipment Service Solutions, LLC 5 Manila Drive Hamden, CT 06514-0322 203-248-7553 1-800-397-7553 Grainger Parts Operations 1657 Shermer Road Northbrook, IL 60062-5362 708-498-5900 1-800-323-0620 www .grainger.com Portable Heater Parts 342 Nort ...

  • Remington r300 - page 48

    48 1 19586 DESA Power T ools™ garantiza a la modelo R300 de Reming- ton ® de defectos en materiales y mano de obre por un período de un (1) año (90 dí as para pro ductos r econdic ionado s) a partir de la fecha de compra. Al realizarse un reclamo según la garantía debe presentarse la factura o el comprobante de compra. Si dentr o de un (1) ...

  • Remington r300 - page 49

    49 1 19586 REMINGTON R300 S F Mode d’emploi Lire toutes les directives et tous les avertissements apparais- sant dans le présent guide et sur l’emballage des cartouches explosives avant d’utiliser l’outil actionné par explosif. S’assu- rer que le guide accompagne de tout temps le pistolet et lors d’un changement de propriétaire, il e ...

  • Remington r300 - page 50

    50 1 19586 S F REMINGTON R300 S F Index Avertissement : Mesures de précaution ........................ 51-59 Ancrage d’un goujon d’ancrage ........................................... 60 Sélection des goujons d’ancrage et des cartouches explosives ....................................................... 61 Utilisation ........................ ...

  • Remington r300 - page 51

    51 1 19586 ? ? S F S F 489.004 S F D E FEC TIVE DÉFECTUEUX A vertissement : Mesures de précaution Le s pa ge s s ui va nt es po rt en t s ur le s a ve rt iss em en ts , l es me su re s de pr éc au ti on à ob se rv er et le s rè gl es co nc er na nt le ma ni em en t sé cu ri ta ir e l’ ou ti l. Av an t le m an ie me nt de l’ ou ti l, li re ...

  • Remington r300 - page 52

    52 1 19586 SE TRABAJA CON HERRAMIENT AS ACCIONADAS CON PÓL VORA ADVERTENCIA ! S F S F S F S F S F 5. TOUJOURS s’assurer que la zone de travail est propre et exempte de matériaux mobiles et de débris. Mesures de précaution 1. NE JAMAIS poser la main sur la bouche. Une décharge accidentelle pourrait entraîner des blessures graves. MANIPULA TI ...

  • Remington r300 - page 53

    53 1 19586 P O W E R L O A D S P O W E L O A D S F S F S F S F S F S F S F Mesures de précaution 4. NE JAMAIS transporter un l’outil chargé ni ne le passer à quelqu’un d’autre. NE JAMAIS pointer vers quelqu’un un l’ou til. 3. T O UJ O U RS ra nge r l’o uti l à l’é tat NO N CH AR GÉ et le s ch ar ges da ns un c on ten ant ve rro ...

  • Remington r300 - page 54

    54 1 19586 ? ? ? Mesures de précaution 7. T out utilisateur suivant un régime de médicaments doit prendre d’extrêmes précautions lors du manie- ment du l’outil. NE JAMAIS boire de boissons alcooli- sées ni prendre des médi- caments qui diminuent la vue ou le jugement avant d’utiliser le l’outil. BIEN CONNAÎTRE LE MA TÉRIAU DE BASE ...

  • Remington r300 - page 55

    55 1 19586 S F S F VERRE FONTE S F S F S F Mesures de précaution 3. NE JAMAIS enfoncer de goujons dans une surface écaillée ou craquelée. 2. NE JAMAIS essayer d’enfoncer de goujons dans un ma- tériau trop dur ou trop friable, y compris, entre autres, la fonte, le verre, le carrelage, la pierre, la brique ou l’acier trempé. De tels matéri ...

  • Remington r300 - page 56

    56 1 19586 90˚ S F NO S F YES S F OUI NON 7. NE P AS enfoncer de goujons dans du matériau en acier dont l’épaisseur est de moins de 5 mm (3/16 po). Ne pas enfoncer de goujons à moins de 51 mm (2 po) d’une sou - dure, à moins de 13 mm (0,5 po) du bord ou à moins de 25,5 mm (1 po) d’un autre goujon. 76mm 76mm 76mm 6. NE JAMAIS enfoncer de ...

  • Remington r300 - page 57

    57 1 19586 30 S F S F S F WA TER S F EAU Anti- éclats 3. TOUJOURS utiliser la protection anti-éclats lorsqu’on tire directement dans du béton ou de l’acier . TOUJOURS porter des lunettes de protection. 4. NE JAMAIS utiliser un outil de fixation, actionné par poudre dans un milieu déflagrant ou inflammable, ou lorsque les outils produisa ...

  • Remington r300 - page 58

    58 1 19586 3. NE JAMAIS utiliser de cartouches explosives dans une arme à feu. 5. To ute per son ne d alt oni enne do it f air e ex trê meme nt att ent ion po ur évi te r d e m êl er les c art ouc he s d e d if fér ent s niv eau x. 4. NE JAMAIS transporter de goujons ou d’autres objets durs dans la même poche ou le même contenant que les c ...

  • Remington r300 - page 59

    59 1 19586 2 1 UNLOAD S F 1 2 LOAD S F CHARGER DÉCHARGER 7. NE JAM AIS remplacer les goujons par des clous ordinaires ou d’autres matériaux. Les goujons d’ancrage Reming- ton MD sont fabriqués à partir d’acier spécial et traités thermi- quement afin de les rendre à la fois très durs et ductiles. 8. N E J AM A IS f orc er une c ha rge ...

  • Remington r300 - page 60

    60 1 19586 POURQUOI LE GOUJON D’ANCRAGE TIENT DANS LE BÉTON L ’a dhé ren ce du bét on sur le gou jon d’ anc rag e ex erc e une com pre ss ion qu i ex pli que en g ran de p ar tie la f orc e de ret enu e ob serv ée. Le go ujon dé- pl ace un e c ert ain e q uan tité d e b éto n qu i te nte de rep ren dre sa for me orig i- na le et ex erc ...

  • Remington r300 - page 61

    61 1 19586 ANCRAGE DANS LE BÉTON On peut déterminer la longueur appro- priée du goujon d’ancrage en faisant la somme de l’épaisseur du matériau à fixer et de la longueur de la partie du goujon qui doit pénétrer dans le béton. Le béton doit être trois fois plus épais que la longueur de pénétration du goujon d’ancrage. Dans la pl ...

  • Remington r300 - page 62

    62 1 19586 S F 489.004 S F 489.004 Sécurité enclenchée S F 2. Saisir la bouche et faire glisser le canon rapidement vers l’avant jusqu’à ce qu’il arrête. Cette opération règle le piston en position de tir et ouvre la chambre. 4. Sélectionner la cartouche explosive Remington MD appro- priée (voir le T ableau des applications aux pages ...

  • Remington r300 - page 63

    63 1 19586 S F 489.004 S F S F S F 90˚ S F Sécurité désenclenchée S F 5. Pousser le canon dans le boîtier jusqu’à la position fer- mée. 6. Placer la bouche de l’outil perpendiculairement à la surface de travail sans pencher l’outil. Exercer une pression sur l’outil contre la surface de travail jusqu’à ce que le glisse- ment du c ...

  • Remington r300 - page 64

    64 1 19586 30 S F WA TER S F EAU ENTRETIEN DU Nettoyer le R300 chaque jour après son utilisation. Nett oyez la cham bre avec la brosse méta llique acce ssoire , num éro de pi èce 5648 5 (No n fou rnie avec l’o util). V aporiser un peu de lubrifiant de bonne qualité (tel que WD-40) et essuyer avec un chiffon. REMA RQUE : Les règlem ents sur ...

  • Remington r300 - page 65

    65 1 19586 Liste des pièces 1 5 4 8 17 16 7 6 9 3 2 10 18 1 1 13 12 20 15 14 21 19 Nº N° de clé pièce Description Qté 1 300001 Vis de la poignée 2 2 3001 10 Poignée 1 3 300101 Interrupteur de sécurité 1 4 300103 Rondelle de blocage 1 5 300104 Vis de l’interrupteur de sécurité 1 6 300105 Détente 1 7 300106 Ressort de la détente 1 8 3 ...

  • Remington r300 - page 66

    66 1 19586 S F A S F B D S F B C F B C A S F D B 3. Pour l’assemblage, re- pousser le piston (E) tout au fond du canon (B) au moyen d’un tournevis (G). Faire glisser le canon (B) dans le boîtier de culasse (D). Faire tourner le canon (B) de sorte à aligner la fente (F) du montant de culasse (C) avec ce der- nier . Insérer le montant de culas ...

  • Remington r300 - page 67

    67 1 19586 PROBLÈME Le piston sort de la bouche. Goujon trop en- foncé. Piston bloqué. Cartouche utili- sée impossible à retirer . Réduction ou perte de puis- sance. Outil ne se dé- tend pas com- plètement. CAUSE POSSIBLE L ’outil a été soumis à une pression ex- cessive. Piston mal installé au niveau de la vis du tube. Piston brisé. ...

  • Remington r300 - page 68

    68 1 19586 PROBLÈME Charge n’ex- plose pas. Ou ve rt ur e et f er - me tu re du t ub e ou pr es si on su r l’outil manque de so up le ss e e t se fait par à- co up s. CAUSE POSSIBLE Outil ne se dé- tend pas complè- tement. Accumulation de saleté dans la cu- lasse, qui empê- che le percuteur d’y pénétrer cor- rectement. L ’interrupte ...

  • Remington r300 - page 69

    69 1 19586 IMPORT ANT • Les utilisations recommandées s’appliquent à des cartou- ches explosives et à des goujons d’ancrage Remington MD . • S i l e go u jo n d ’a n cr ag e p én è tr e s ou s l a s ur f a ce su pé r ie u re d u p an n e au , ut i li se r u n l im it e ur d’ en f on c em en t ( vo ir il l us t r at i o n c i- de s ...

  • Remington r300 - page 70

    70 1 19586 Service de Réparation Remarque : Utilisez seulement des pièces de rechange d’ori- gine. V ous aurez ainsi droit à la protection de la garantie pour toute pièce remplacée en vertu de la garantie. SERVICE SOUS GARANTIE Si le produit doit être réparé pendant la période de validité de la garantie, apportez-le au centre de service ...

  • Remington r300 - page 71

    71 1 19586 SERVICE HORS GARANTIE Si le produit doit être réparé, apportez-le au centre de service autorisé le plus proche. Les frais de réparation vous seront facturés conformément au prix habituel des réparations. Pour plus de détails sur le centre de service ou sur la garantie, faites le 1 800 858-8501 (en ang lai s seu lem ent ) ou visi ...

  • Remington r300 - page 72

    Garantie Limitée 1 19586-01 REV . A 06/06 DESA Power T ools MC garantit le Modèle R300 de Remington MD contre tout défaut de matériau ou de fabrication pour une période d’un (1) an (90 jours pour les produits remis à neuf) suivant la date d’achat. Le bordereau d'achat ou le ticket de caisse devra être présenté lors d'une réc ...

Manufacturer Remington Category Power Screwdriver

Documents that we receive from a manufacturer of a Remington r300 can be divided into several groups. They are, among others:
- Remington technical drawings
- r300 manuals
- Remington product data sheets
- information booklets
- or energy labels Remington r300
All of them are important, but the most important information from the point of view of use of the device are in the user manual Remington r300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Remington r300, service manual, brief instructions and user manuals Remington r300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Remington r300.

Similar manuals

A complete manual for the device Remington r300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Remington r300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Remington r300.

A complete Remington manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Remington r300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Remington r300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Remington r300, that we can find in the current document
3. Tips how to use the basic functions of the device Remington r300 - which should help us in our first steps of using Remington r300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Remington r300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Remington r300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Remington r300?

Use the form below

If you did not solve your problem by using a manual Remington r300, ask a question using the form below. If a user had a similar problem with Remington r300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)