Manual Omron LCM100

10 pages 0.61 mb
Download

Go to site of 10

Summary
  • Omron LCM100 - page 1

    U SER G UIDE I NDUSTRIAL D ATA C OMMUNICA TIONS It is essential that all instructions contained in the User Guide are followed precisely to ensure proper operation of equipment. Line Carrier Modem LCM100 ...

  • Omron LCM100 - page 2

    DA T A-LINC GROUP PN 161-xxxxx-001A Product User Guide FCC Information Appropriate FCC info ...

  • Omron LCM100 - page 3

    DA T A- L I N C GROUP p LCM100 User’s Guide LCM100 Line Carrier Modem Introduction In the line carrier system, the hot line supplies current to connected loads and is a lso used as a carrier for data communication between modules. The Data-Linc LCM100 can communicate over the same line in a 240 volt single phase system or on any individual phase ...

  • Omron LCM100 - page 4

    DA T A- L I N C GROUP p LCM100 User’s Guide Note: If a three-to-two-wire adapter is used to connect to a two-wire AC outlet, the ground lead of the adapter must be connected to earth ground to complete the ground system. An open ground connection may cause a communications defect and/or shock hazard. Line conditioners in the form of isolators, re ...

  • Omron LCM100 - page 5

    DA T A- L I N C GROUP p LCM100 User’s Guide Communication Failure C a r r i e r D e t e c t O f f RS-232C Input Modulator/Oscillator Failure Failure P o w e r Indicator Off Receiver Signal Modulator Cable/CNX Circuitry Coupler Oscillator Failure Failure Failure Failure C i r c u i t B r e a k e r Open Fuse Power Breaker Blows Fails Open Fault Tre ...

  • Omron LCM100 - page 6

    DA T A- L I N C GROUP p LCM100 User’s Guide LCM100 Technical Specifications Power requirements 120 volts at +/- 10%, 50- 60 Hz, 4.5 watts. Power is on when module(s) are con nected Data Rate Up to 9600 baud Data Formats Any serial asynchronous format up to 9600 ba ud Operation Full Duplex Receive Sensitivity 20 millivolts Transmit Level 250mW int ...

  • Omron LCM100 - page 7

    DA T A- L I N C GROUP p LCM100 User’s Guide Appendix A RS-232 Connector Pin Assignments Both modules of the LCM100 have female DB-25 connectors which can be directly connected to DTE and DCE equipment. All output levels are a minimum of +6 volts when active and a maximum of –6 volts when inactive, measured in a 3k ohm load. Inputs will sink 10M ...

  • Omron LCM100 - page 8

    DA T A- L I N C GROUP p LCM100 User’s Guide Connector J2 (Female) Please note that male pin numbering is a mirror image of the female connector depicted below: 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 Figure 3: DB-25P J2 Connector Pins J2 Pin Description 9-19 Pins 9-19 are unused, open. 20 Data Terminal Ready Data Termina ...

  • Omron LCM100 - page 9

    DA T A- L I N C GROUP p LCM100 User’s Guide Appendix B Line Conditioning In some industrial installations, power lines must be conditioned to prevent the FSK signal from being shunted by distributed capacitance possibly associated with other loads conne cted to the line. Motors and transformers, for example, may have very high distributed capacit ...

  • Omron LCM100 - page 10

    DA T A- L I N C GROUP p LCM100 User’s Guide Appendix C System Block Diagram Data T erminal Equipment RS-232C Interface DB-25P Connec tors w/Cab le Pin 2 LCM 100-2 Data Communicatio ns Equipment RS-23 2C Int erfa ce DB-25P Connec tors w/Cable Pin 2 Data Out Data In LCM100-1 Data In Data Out Frequency Modulator Lowb and Oscillat or Carrier Detect C ...

Manufacturer Omron Category Modem

Documents that we receive from a manufacturer of a Omron LCM100 can be divided into several groups. They are, among others:
- Omron technical drawings
- LCM100 manuals
- Omron product data sheets
- information booklets
- or energy labels Omron LCM100
All of them are important, but the most important information from the point of view of use of the device are in the user manual Omron LCM100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Omron LCM100, service manual, brief instructions and user manuals Omron LCM100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Omron LCM100.

A complete manual for the device Omron LCM100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Omron LCM100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Omron LCM100.

A complete Omron manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Omron LCM100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Omron LCM100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Omron LCM100, that we can find in the current document
3. Tips how to use the basic functions of the device Omron LCM100 - which should help us in our first steps of using Omron LCM100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Omron LCM100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Omron LCM100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Omron LCM100?

Use the form below

If you did not solve your problem by using a manual Omron LCM100, ask a question using the form below. If a user had a similar problem with Omron LCM100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)