Manual Epson 36-714

32 pages 3.82 mb
Download

Go to site of 32

Summary
  • Epson 36-714 - page 1

    INSTRUCTION MANUAL Delta 10" Hybrid Saw (Model 36-714) P ART NO. A08139 - 06-14-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). NOTE: Shown with BC30 30” ...

  • Epson 36-714 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Epson 36-714 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Epson 36-714 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Epson 36-714 - page 5

    5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. ...

  • Epson 36-714 - page 6

    6 6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before conn ...

  • Epson 36-714 - page 7

    EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized c ...

  • Epson 36-714 - page 8

    CAR TON CONTENTS Fig. 1 Parts 1. Cast Iron Extension Wings (2) 2. Switch Assembly 3. Fence Holder Brackets (2) 4. Drive Belt 5. T able Insert 6. Wr ench Hook 7. Miter Gage Holder 8. Splitter Mounting Bracket 9. Blade Hex Nut 10. Blade Flange 11. 10” Carbide- Tipped Blade 12. Blade W renches (2) 13. 4mm Hex Wr ench 14. Dust Port 15. Locking Knobs ...

  • Epson 36-714 - page 9

    9 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be r emoved with a soft cloth moistened with kerosene (do not us e acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surface ...

  • Epson 36-714 - page 10

    10 Fig. 4 DISCONNECT MACHINE FROM POWER SOURCE. T o bolt the saw to a permanent location, remove the nine screws which secur e the dust chute inside the saw cabinet, six of which are shown at (C) Fig. 4. Also, remove the side panel below the motor cover by loosening all six screws (D). Find the holes (E) Fig. 5 in the bottom of the saw and mark the ...

  • Epson 36-714 - page 11

    DISCONNECT MACHINE FROM POWER SOURCE. First, lift motor and remove foam packing block fr om around motor . While lifting motor (A) Fig. 8, place a 10-12 inch long piece of 2x4, or another similar thickness of wood, (B) Fig. 8 as shown. This will help prop up the motor and will make it easier to install the grooved belt, (C) Fig. 8A. Place grooved b ...

  • Epson 36-714 - page 12

    12 Fig. 10 DISCONNECT MACHINE FROM POWER SOURCE. Assemble left extension wing (A) Fig. 10A to the saw table. Align the three holes in the extension wing with the three holes (A) Fig. 9 in the side of the saw table. Place a 7/16" lockwasher , then a 7/16" flat washer on a 7/16- 20x1-1/4” hex head screw (all shown at (B) Fig. 9). In ser t ...

  • Epson 36-714 - page 13

    13 INST ALLING THE SWITCH DISCONNECT MACHINE FROM POWER SOURCE. 1. Place switch (A) Fig. 11, behind the lip of extension wing (B). Insert M8x30 hex head screw (C) thr ough wing and then switch support. Place an M8 flat washer and an M8 lock washer on the screw . Thread an M8 hex nut (D) onto screw and tighten nut secur ely . 2. Insert switch cord w ...

  • Epson 36-714 - page 14

    14 ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE . MAKE SURE BLADE IS NOT A TT ACHED. IF IT IS, REMOVE THE SAW BLADE FROM THE SA W USING THE SUPPLIED WRENCHES. 1. Fasten the r ear splitter mounting bracket (A) Fig. 15, to the rear trunnion on the back of the saw using the two 1/4”-20 x 3/4 ″ hex head screws ...

  • Epson 36-714 - page 15

    15 5. If alignment is necessary , loosen the two screws (F) Fig. 18, align bracket (D) with the inner arbor flange (E), and tighten screws (F). 6. Loosely assemble large washer and scr ew (C) Fig. 18, to the inside splitter bracket. This screw and washer was removed in STEP 3 . 7. Assemble the blade guar d and splitter assembly (G) Fig. 19 between ...

  • Epson 36-714 - page 16

    16 SAW BLADE DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the saw blade arbor to its maximum height. Assemble the saw blade (C) Fig. 23 to the saw arbor making sure the teeth of the blade point down towards the fr ont of the table, as shown in Fig. 23. Assemble the flange (D) and arbor nut (E) to the saw arbor and tighten arbor nut (E) as far as ...

  • Epson 36-714 - page 17

    17 Fig. 26 L P INST ALLING T ABLE INSER T DISCONNECT MACHINE FROM POWER SOURCE. Lower saw blade and install table insert (P) Fig. 26, in the saw table. IMPORT ANT : When installing the table insert, make certain to hold on to the blade guard (L). The insert will automatically release the holding action on the splitter and lower the blade guard when ...

  • Epson 36-714 - page 18

    18 ASSEMBLING MITER GAGE DISCONNECT MACHINE FROM POWER SOURCE Place a flat washer (A) Fig 30 on the threads of the miter gage lock handle (B) and then thread the handle into the hole (C) in miter gage bar . Insert plate (D) Fig.41 into the miter gage slot (E) Fig. 41 and slide miter gage onto saw table. Fig. 30 OPERA TION ST AR TING AND STOPPING SA ...

  • Epson 36-714 - page 19

    19 Fig. 33 C Fig. 34 E D ADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPS The machine is equipped with positive stops that will quickly and accurately position the saw blade at 90° and 45° to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the blade guard and splitter . 2. Ra ...

  • Epson 36-714 - page 20

    20 Fig. 38 A B D C BACKLASH ADJUSTMENTS DISCONNECT MACHINE FROM POWER SOURCE. After a period of extended use, if any play is detected in the blade raising or blade tilting mechanisms, remove the blade and make the following adjustments: ADJUSTING BLADE RAISING MECHANISM - Loosen locknut (A) Fig. 38, and turn eccentric sleeve (B) until all play is r ...

  • Epson 36-714 - page 21

    21 MITER GAGE OPERA TION AND ADJUSTMENT The miter gage is equipped with adjustable index stops at 90, 75, 60,45 and 30 degrees. T o rotate the miter gage, loosen lock knob (A) Fig. 40, push the thumb lever (B) down and move the body of the miter gage (C) to the desired angle. The miter gage is equipped with a plate (D) Fig.41 which fits into the T ...

  • Epson 36-714 - page 22

    22 CROSS-CUTTING Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 42. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the table groove that does not cause interferen ...

  • Epson 36-714 - page 23

    23 Ripping is cutting lengthwise through a boar d, (Fig. 45). NOTE : Be sure the material to be cut is seasoned, dry and flat. The rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must have a strai ...

  • Epson 36-714 - page 24

    24 Fig. 49 Fig. 51 Fig. 50 H G USING MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.The many differ ent knife shapes available make it possible for the operator to produce almost any kind of mouldings, such as various styles of corner ...

  • Epson 36-714 - page 25

    25 Fig. 56 Fig. 54 Fig. 55 Fig. 53 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 53). V arious combinations of saws and cutters are used to cut grooves fr om 1/8 ″ to 13/16 ″ for use in shelving, making joints, tenoning, grooving, etc. The ...

  • Epson 36-714 - page 26

    26 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). Fig. 59, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should ...

  • Epson 36-714 - page 27

    27 When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 78. Fig. 78 PUSH STICK MAKE FROM 1/2 " OR 3/4 " WOOD OR THICKNESS LESS THAN WIDTH OF MA TERIAL TO BE CUT CUT OFF HERE TO PUSH 1/4 " WOOD CUT OFF HERE TO PUS ...

  • Epson 36-714 - page 28

    28 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Epson 36-714 - page 29

    29 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with ...

  • Epson 36-714 - page 30

    30 NOTES ...

  • Epson 36-714 - page 31

    31 NOTES ...

  • Epson 36-714 - page 32

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Manufacturer Epson Category Saw

Documents that we receive from a manufacturer of a Epson 36-714 can be divided into several groups. They are, among others:
- Epson technical drawings
- 36-714 manuals
- Epson product data sheets
- information booklets
- or energy labels Epson 36-714
All of them are important, but the most important information from the point of view of use of the device are in the user manual Epson 36-714.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Epson 36-714, service manual, brief instructions and user manuals Epson 36-714. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Epson 36-714.

Similar manuals

A complete manual for the device Epson 36-714, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Epson 36-714 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Epson 36-714.

A complete Epson manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Epson 36-714 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Epson 36-714, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Epson 36-714, that we can find in the current document
3. Tips how to use the basic functions of the device Epson 36-714 - which should help us in our first steps of using Epson 36-714
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Epson 36-714
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Epson 36-714 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Epson 36-714?

Use the form below

If you did not solve your problem by using a manual Epson 36-714, ask a question using the form below. If a user had a similar problem with Epson 36-714 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)