Manual Friedrich 115 Volts UE08

23 pages 0.85 mb
Download

Go to site of 23

Summary
  • Friedrich 115 Volts UE08 - page 1

    UE08/UE10/UE12 (05/05) Thru-the-Wall Series Thru-the-Wall Series Ser vice and P ar ts Man ual 115 Volts UE08 230 Volts UE10 UE12 ...

  • Friedrich 115 Volts UE08 - page 2

    —2— 1. PREF A CE 1.1 SAFETY PRECAUTIONS ...............................2 1.2 INSULATION RESISTANCE TEST.................2 1.3 SPECIFICATIONS ..........................................3 1.4 FEATURES .....................................................4 1.5 CONTROL LOCATIONS .................................4 2. DISASSEMBL Y INSTR UCTIONS 2.1 ME ...

  • Friedrich 115 Volts UE08 - page 3

    —3— 1.3 SPECIFICA TIONS 1.3.1 FOR UE08A13B/UE10A33B/UE12A33B REMARK POWER SUPPLY CAPACITY (Btu/h) INPUT (W) RUNNING CURRENT (A) E.E.R. (Btu/W.h) CAPACITY (Btu/h) INPUT (W) RUNNING CURRENT (A) INDOOR (°C) OUTDOOR (°C) INDOOR (°C) OUTDOOR (°C) REFRIGERANT (R-22) CHARGE(g) EVAPORATOR CONDENSER FAN, INDOOR FAN, OUTDOOR FAN SPEEDS (FAN/COOLING/H ...

  • Friedrich 115 Volts UE08 - page 4

    1.4 FEA TURES • Designed for cooling only. • Powerful and quiet cooling. • Top-down chassis for the simple installation and service. 1.5 CONTR OL LOCA TIONS • Built in adjustable THERMISTOR and THERMOSTAT. • Washable one-touch filter. • Compact size. • VENTILA TION Push the lever to the "CLOSE" position to cool, heat or reci ...

  • Friedrich 115 Volts UE08 - page 5

    —5— 2.1 MECHANICAL P AR TS 2.1.1 FRONT GRILLE 1. Open the inlet grille downward. 2. Remove the screw which fastens the front grille. 3. Pull the front grille from the right side. 4. Remove the front grille. (See Fig. 1) 5. Re-install the component by referring to the removal procedure. 2.1.2 CABINET 1. After disassembling the FRONT GRILLE, remo ...

  • Friedrich 115 Volts UE08 - page 6

    Figure 7 —6— 2.2 AIR HANDLING P AR TS 2.2.1 ORIFICE, HEA TER ASSY AND TURBO F AN 1. Remove the front grille. (Refer to section 2.1.1) 2. Remove the cabinet. (Refer to section 2.1.2) 3. Remove the 2 screws which fasten the evaporator at the left side and the right side. (See Fig. 4) 4. Move the evaporator sideward carefully. 5. Remove the 2 term ...

  • Friedrich 115 Volts UE08 - page 7

    —7— 2.2.3 SHROUD 1. Remove the fan. (Refer to section 2.2.2) 2. Remove the screw which fastens the shroud. 3. Remove the shroud. (See Fig. 9) 4. Re-install the components by referring to the removal procedures, above. 2.3 ELECTRICAL P AR TS 2.3.1 MO T OR 1. Remove the cabinet. (Refer to section 2.1.2) 2. Remove the clamp cord and disconnect the ...

  • Friedrich 115 Volts UE08 - page 8

    —8— 2.3.4 PO WER CORD 1. Remove the control box. (Refer to section 2.1.3) 2. Unfold the control box. (Refer to section 2.3.3) 3. Disconnect the grounding screw from the control box. 4. Disconnect 2 receptacles. 5. Remove a screw which fastens the clip cord. 6. Pull the power cord. (See Fig. 13) 7. Re-install the components by referring to the r ...

  • Friedrich 115 Volts UE08 - page 9

    —9— 2.4 REFRIGERA TION CYCLE 2.4.1 CONDENSER 1. Remove the cabinet. (Refer to section 2.1.2) 2. Remove the brace and the shroud cover. (Refer to section 2.2.1) 3. Remove the 5 screws which fasten the condenser. 4. After discharging the refrigerant completely into a Freon TM Recovery System, unbraze the interconnecting tube at the condenser conn ...

  • Friedrich 115 Volts UE08 - page 10

    —10— — Replacement of the refrigeration components 1. When replacing the refrigeration components , be sure to discharge the refrigerant system using a FreonTM recovery System. Install a valve for the recovery before venting the Freon. Remove the valve when finished. 2. After discharging the unit completely, remove the desired component, and ...

  • Friedrich 115 Volts UE08 - page 11

    —11— Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment. Pinch-off tool capable of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service valve. A COMPOUND GAUGE EVAPORATOR (LOW PRESSURE SIDE) COMPRESSOR CAPILLARY TUBE CONDENSER (HIGH PRESSURE SIDE) SEE INSETS BELOW MAN ...

  • Friedrich 115 Volts UE08 - page 12

    — 12 — 3. TR OUBLESHOO TING GUIDE 3.1 OUTSIDE DIMENSIONS 19- 21 / 32 " (499mm) 24- 21 / 32 " (626mm) 14- 13 / 32 " (366mm) CONDENSER COILS EV APORA TOR COILS FA N M OTO R : REFRIGERANT FLOW TURBO F AN CAPILLAR Y TUBE COMPRESSOR 3.2 PIPING SYSTEM Following is a brief description of the important components and their functions in t ...

  • Friedrich 115 Volts UE08 - page 13

    — 13 — 3.3 TR OUBLESHOO TING GUIDE In general, possible trouble is classified in two causes. The one is called Starting Failure which is caused from an electrical defect, and the other is Ineffective Air Conditioning caused by a defect in the refrigeration circuit and improper application. Unit is running but cooling is ineffective Ineffective ...

  • Friedrich 115 Volts UE08 - page 14

    — 14 — Fails to Start Check circuit break er and fuse. Gas leakage at f eeler bulb of ther mostat Check control s witch. Only f an f ails to star t. Improper wiring. Def ect of f an motor capacitor . Irregular motor resistance ( ). Irregular motor insulation ( ). Replacement of f an motor Regular but f ails to star t Replacement of compressor ( ...

  • Friedrich 115 Volts UE08 - page 15

    — 15 — — 15 — COMPLAINT CAUSE REMEDY Check voltage at outlet. Correct if none. Check voltage to rotary switch. If none, check power supply cord. Replace cord if circuit is open. Check switch continuity. Refer to wiring diagram for terminal identification. Replace switch if defective. Connect wire. Refer to wiring diagram for terminal identi ...

  • Friedrich 115 Volts UE08 - page 16

    — 16 — NAME PLATE RATING MINIMUM MAXIMUM 115V 103.5V 126.5V 208/230V 187V 253V COMPLAINT CAUSE REMEDY Check voltage. See the limits at the bottom of this page. If not within limits, call an electrician. Check the wire connections, if loose, repair or replace the terminal. If wires are off, refer to wiring diagram for identification, and replace ...

  • Friedrich 115 Volts UE08 - page 17

    — 17 — COMPLAINT CAUSE REMEDY Check the voltage. See the limits on the preced- ing page. If not within limits, call an electrician. Check overload, if externally mounted. Replace if open. (If the compressor temperature is high, remove the overload, cool, and retest.) If not running, determine the cause. Replace if required. Remove the cabinet. ...

  • Friedrich 115 Volts UE08 - page 18

    — 18 — 4. SCHEMA TIC DIA GRAM 4.1 CIRCUIT DIA GRAM • MODEL : UE08A13B/UE10A33B/UE12A33B 6411A20048F 6411A20048L 67300502 67303019 67303010 4681A20041M 67300714 67300711 67300404 67301625 67301623 2525UKHK2AA 67301411 67301413 6750U-L039A 67301411 67310100 3854AR3563D WIRING DIA GRAM COMP MO TOR CAP ACIT OR RO T ARY SWITCH POWER INPUT 7 1 8 6 ...

  • Friedrich 115 Volts UE08 - page 19

    — 19 — 5. EXPLODED VIEW • MODEL: UE08A13B/UE10A33B/UE12A33B 354210 753010 753011 349480 554031 W48602 559010 346811 349600 567502 349001 130410 352113 35211A 352115 W48602 249950 137215 149410 W0CZZ 264110 130900 135312 147581 147582-2 147582-1 352390 148000 554160 550140 149980 359012 266003 269310 552111 152302 135313 E D F A G C B 749180 4 ...

  • Friedrich 115 Volts UE08 - page 20

    6. REPLA CEMENT P AR TS LIST • MODEL: UE 08A13B R: Service Parts N: Non Service parts LOCATION NO. MODEL FRIEDRICH # DESCRIPTION 130410 UE08A13B 67302917 BASE ASSEMBLY,SINGLE 1 R 130900 UE08A13B 67303705 CABINET 1 R 135312 UE08A13B 67306006 GRILLE ASSEMBLY,FRONT(SINGLE) 1 R 135313 UE08A13B 67306104 GRILLE,INLET 1 R 137215 UE08A13B 67305504 PANEL ...

  • Friedrich 115 Volts UE08 - page 21

    — 21 — • MODEL: UE10A33B R: Service Parts N: Non Service parts LOCATION NO. MODEL FRIEDRICH # DESCRIPTION 130410 UE10A33B BASE ASSEMBLY,SINGLE 1 R 130900 UE10A33B 67303705 CABINET 1 R 135312 UE10A33B 67306005 GRILLE ASSEMBLY,FRONT(SINGLE) 1 R 135313 UE10A33B 67306104 GRILLE,INLET 1 R 137215 UE10A33B 67305504 PANEL ASSEMBLY,CONTROL 1 R 147581 ...

  • Friedrich 115 Volts UE08 - page 22

    — 22 — • MODEL: UE12A33B R: Service Parts N: Non Service parts LOCATION NO. MODEL FRIEDRICH # DESCRIPTION 130410 UE12A33B 67302918 BASE ASSEMBLY,SINGLE 1 R 130900 UE12A33B 67303705 CABINET 1 R 135312 UE12A33B 67306005 GRILLE ASSEMBLY,FRONT(SINGLE) 1 R 135313 UE12A33B 67306104 GRILLE,INLET 1 R 137215 UE12A33B 67305504 PANEL ASSEMBLY,CONTROL 1 ...

  • Friedrich 115 Volts UE08 - page 23

    UE08/UE10/UE12 (05/05) Printed in the U.S.A Post Office Box 1540 • 4200 N. Pan Am Expressway • San Antonio, Texas 78295-1540 • (210) 357-4400 • FAX (210) 357-4480 FRIEDRICH AIR CONDITIONING CO. Visit our web site at www.friedrich.com P/NO.:3828A20040G ...

Manufacturer Friedrich Category Air Conditioner

Documents that we receive from a manufacturer of a Friedrich 115 Volts UE08 can be divided into several groups. They are, among others:
- Friedrich technical drawings
- 115 Volts UE08 manuals
- Friedrich product data sheets
- information booklets
- or energy labels Friedrich 115 Volts UE08
All of them are important, but the most important information from the point of view of use of the device are in the user manual Friedrich 115 Volts UE08.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Friedrich 115 Volts UE08, service manual, brief instructions and user manuals Friedrich 115 Volts UE08. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Friedrich 115 Volts UE08.

Similar manuals

A complete manual for the device Friedrich 115 Volts UE08, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Friedrich 115 Volts UE08 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Friedrich 115 Volts UE08.

A complete Friedrich manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Friedrich 115 Volts UE08 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Friedrich 115 Volts UE08, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Friedrich 115 Volts UE08, that we can find in the current document
3. Tips how to use the basic functions of the device Friedrich 115 Volts UE08 - which should help us in our first steps of using Friedrich 115 Volts UE08
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Friedrich 115 Volts UE08
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Friedrich 115 Volts UE08 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Friedrich 115 Volts UE08?

Use the form below

If you did not solve your problem by using a manual Friedrich 115 Volts UE08, ask a question using the form below. If a user had a similar problem with Friedrich 115 Volts UE08 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)