Manual Elo TouchSystems 6.3.0

14 pages 0.95 mb
Download

Go to site of 14

Summary
  • Elo TouchSystems 6.3.0 - page 1

    Elo Touch Solutions Multi-touch Driver Package User Manual Elo Touch Solution s 1033 McCarthy Blvd Milpitas, CA 95035 Package Version: 6.3.0 Release Date: July 17, 2014 Supported OS: W ind ows XP W ind ows 7 W ind ows 8 / 8.1 W ind ows Server 2012 / 2012R2 Supported Touch Technologies: iTouch (SAW ) iTouch Plus (SA W ) pCap Optical Int elliT ouch ( ...

  • Elo TouchSystems 6.3.0 - page 2

    1.1 Installation • Double click on EloSetup .exe • Accept the installation ag ree ment and proceed wi th the insta llation pro cess. 1.2 Uninstallatio n • Launch the Control Pan el and choos e Progra ms and Features. • Select to re move “Elo Tou ch Solutions 6.3.0.x”. 1.3 Silent Installa tion • Open the command line shell as an admini ...

  • Elo TouchSystems 6.3.0 - page 3

    3. Configuration Program: EloConfig.exe This is the c onfiguration tool for t he Elo Multi-Touch driv ers. The set up program will launch t he tool at the end of the ins tallation. This program will be runnin g in t he background and will launch when t he user starts it from the Wi ndow’ s Cont rol Panel, or manually execut e it from t he desktop ...

  • Elo TouchSystems 6.3.0 - page 4

    The Elo calibration tool is used to calibrate touch recognition on supported Elo t ouch screen monitors. After touching all 3 targets, the screen will show "Accept " and "Retry" buttons. The us er can t hen t est the calibration accuracy before sele ct ing either “Accept” (saving calibra tion dat a) or “Retry” (r e-doing ...

  • Elo TouchSystems 6.3.0 - page 5

    Launching “Touch Screen Properties” wi ll display various properties of each connected ( and supported) El o touch screen suc h as Monitor Resolution, Co ntroller Serial Number, Controller Firmware Version, etc. In addition to this information, users will be given the ability to “D isable Touch” and “Restore def ault calibrat ion”. Also ...

  • Elo TouchSystems 6.3.0 - page 6

    To en able CEA, click on the "Select D efault" butt on and specify the desired parameters. The position of CEA ma y be manipulated for all edges at once b y means of t he “Increase/ Decrease CEA Area” b uttons, or individ ually b y means of the a rrows along eac h edge. Additional ly, CEA for part icular edges may be disabled by unche ...

  • Elo TouchSystems 6.3.0 - page 7

    section [ Calibration], c hange the value " DriverCalibration" to 1. User does not need t o reinstall t he package for this change t o take effec t. 3.4 Common Setti ngs Configure shared touch screen settings s uch as “ Beep on Touch”, “Touch M ode”, hiding t he cursor during calibratio n, and spanned displa y mode. 3.4.1 Beep on ...

  • Elo TouchSystems 6.3.0 - page 8

    3.4.3 Hide curs or duri ng calibratio n Enabling the set ting will hide the mous e cursor when running the calibrat ion utility. Disabling the sett ing will display the mous e cursor when running t he calibration ut ility. Note: The user must click “Apply” f or a ll changes to take eff ect. Clicking “Close” without c licking “Apply” wil ...

  • Elo TouchSystems 6.3.0 - page 9

    touch zone. • The user can drag t his second box t o any touch screen and adjust it s size and posit ion. • It may be spec ified in t he “EloTouchZones” dialog box whether t ouch wil l be enabled “ inside” or “out side” the zone. If the user chooses to h ave touch enabled “ inside zone”, touch will only work within each defined ...

  • Elo TouchSystems 6.3.0 - page 10

    4. Instructions for Window s 7 Emb edded The fo llowing notes are intended as a guide f or enabling mult i-touch func tionality with W indows 7 Embedded. 4.1 Use Ta p.exe to generat e a PMQ f ile including all hardware information of the target system. 4.2 Start ICE ( Image Configuration Editor), cr eate an ANSW ER file, and import the PMQ f ile. 4 ...

  • Elo TouchSystems 6.3.0 - page 11

    monitor needs to be power cycled, t hen re-calibrated to r estore normal t ouch. If powe r c ycling the monitor is not workin g, the utilti y EloCalMgr.exe (located in the t arget installation folder) can be us ed to re set the controller. 6. Appendix 6.1 Installation/ Uninstallation from Device Ma nager 6.1.1 Installation • Open W indows Device ...

  • Elo TouchSystems 6.3.0 - page 12

    and se parated b y a s pace; No H EX or C HARs. The 8 numbers repres ent t he 8-byte Smartset Command. 6.2.2 Smar tset Comman d Limitati ons: There is no limit to the number of Smartset comman ds that can be sent. For example, if 10 Smartset C ommands (10 lines) are specified under the [Smarts et Commands] section, all 10 Smartset Commands will be ...

  • Elo TouchSystems 6.3.0 - page 13

    Release 4.0.2 • Serial driver: New calibration is not taking eff ect. • Serial driver: After reboot, previous calibration is not applied. • Serial driver: Pre-install either legacy serial driver or multi-touc h serial driver (not both). Release 4.0.3 • Correct t he multi touc h mode in Lumio/Opt ical monitor. • Added W indows 8 su pport. ...

  • Elo TouchSystems 6.3.0 - page 14

    • Correct t he pCap firmware ve rsion shown in the propert y page. • Support both new and old f irmware fo r Optical t ouch monitors. • Provide opt ions to limit nu mber of to uches (please see Readm e). • IDS improveme nts: slow response, incorrec t initial touch status, incorrec t power status report. Release 6.2.1 • Check t he 2521 con ...

Manufacturer Elo TouchSystems Category Recording Equipment

Documents that we receive from a manufacturer of a Elo TouchSystems 6.3.0 can be divided into several groups. They are, among others:
- Elo TouchSystems technical drawings
- 6.3.0 manuals
- Elo TouchSystems product data sheets
- information booklets
- or energy labels Elo TouchSystems 6.3.0
All of them are important, but the most important information from the point of view of use of the device are in the user manual Elo TouchSystems 6.3.0.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Elo TouchSystems 6.3.0, service manual, brief instructions and user manuals Elo TouchSystems 6.3.0. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Elo TouchSystems 6.3.0.

A complete manual for the device Elo TouchSystems 6.3.0, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Elo TouchSystems 6.3.0 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Elo TouchSystems 6.3.0.

A complete Elo TouchSystems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Elo TouchSystems 6.3.0 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Elo TouchSystems 6.3.0, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Elo TouchSystems 6.3.0, that we can find in the current document
3. Tips how to use the basic functions of the device Elo TouchSystems 6.3.0 - which should help us in our first steps of using Elo TouchSystems 6.3.0
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Elo TouchSystems 6.3.0
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Elo TouchSystems 6.3.0 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Elo TouchSystems 6.3.0?

Use the form below

If you did not solve your problem by using a manual Elo TouchSystems 6.3.0, ask a question using the form below. If a user had a similar problem with Elo TouchSystems 6.3.0 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)