Manual Garmin GHP 10V

48 pages 6.39 mb
Download

Go to site of 48

Summary
  • Garmin GHP 10V - page 1

    GHP ™ 10 Marine Autopilot System Installation Instructions T o obtain the best possible performance and to avoid damage to your boat, install the Garmin ® GHP 10 marine autopilot system according to the following instructions. Professional installation of the autopilot system is highly recommended. Specic training in hydraulic pipe-tting a ...

  • Garmin GHP 10V - page 2

    2 GHP 10 Marine Autopilot System Installation Instructions GHP 10 Package Contents and T ools Needed The GHP 10 autopilot system consists of multiple components. Familiarize yourself with all of the components before beginning installation. Y ou must know how the components operate together in order to correctly plan the installation on your boat. ...

  • Garmin GHP 10V - page 3

    3 GHP 10 Marine Autopilot System Installation Instructions The Shadow Drive The Shadow Drive is a sensor you install in the hydraulic steering lines of your boat. While the GHP 10 is engaged, the Shadow Drive temporarily disengages the autopilot when you manually take control of the helm. When you establish a new straight line heading, the Shadow D ...

  • Garmin GHP 10V - page 4

    4 GHP 10 Marine Autopilot System Installation Instructions NMEA 2000 Cables and Connectors The NMEA 2000 cables connect the CCU and the GHC 10 to the NMEA 2000 network. Use the NMEA 2000 power cable and two terminators to create a NMEA 2000 network on your boat if one does not exist. For more information on NMEA 2000, see page 30 . NMEA 2000 drop c ...

  • Garmin GHP 10V - page 5

    5 GHP 10 Marine Autopilot System Installation Instructions Installation Preparation Before installing the GHP 10 autopilot system, it is important for you to completely understand where all the components will be located on your boat. T emporarily place all the components where you plan to install them. Ensure that all cables and hydraulic hoses ca ...

  • Garmin GHP 10V - page 6

    6 GHP 10 Marine Autopilot System Installation Instructions ENCODER CCU POWER } PUMP GHP 10 General Wiring Outline NMEA 2000 network (see page 30 ) CCU ECU Pump (compact 2.1 L pictured) GHC 10 Shadow Drive Alarm buzzer Boat tachometer Y ellow CCU signal wire (see page 29 ) For CCU bare-wire connections, see page 26 . For tachometer wiring, see page ...

  • Garmin GHP 10V - page 7

    7 GHP 10 Marine Autopilot System Installation Instructions Single-helm Layout Guidelines NMEA 2000 network CCU ECU Pump (1.2 L pictured) GHC 10 12 Vdc* NOTE: This diagram is for planning purposes only . Specic wiring diagrams are included in the detailed installation instructions for each component. Hydraulic connections are not shown in this di ...

  • Garmin GHP 10V - page 8

    8 GHP 10 Marine Autopilot System Installation Instructions Dual-helm Layout Guidelines NMEA 2000 network CCU ECU Pump (1.2 L pictured) GHC 10 12 Vdc* GHC 10 NOTE: This diagram is for planning purposes only . Specic wiring diagrams are included in the detailed installation instructions for each component. Hydraulic connections are not shown in th ...

  • Garmin GHP 10V - page 9

    9 GHP 10 Marine Autopilot System Installation Instructions Hydraulic Considerations – 2.0 L and 1.2 L Pumps Different boats have dif ferent hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. Before starting the hydraulic installation, verify the type of hydraulic steering in your boat, and where to inst ...

  • Garmin GHP 10V - page 10

    10 GHP 10 Marine Autopilot System Installation Instructions 2.0 L or 1.2 L Pump Hydraulic Layout on Dual-Helm Boats Balanced cylinder Port tting Starboard tting 2.0 L/1.2 L pump (and motor) Port line Return line Starboard line Shadow Drive Upper helm P R S P R S Lower helm Notes: 2.0 L/1.2 L pump (and motor): An unbalanced cylinder requires a ...

  • Garmin GHP 10V - page 11

    1 1 GHP 10 Marine Autopilot System Installation Instructions 2.0 L or 1.2 L Pump Hydraulic Layout on SeaStar Power Assist-Enabled Boats Notes: Power Assist module: It may be necessary to remove the Power Assist module to gain access to the ttings, the hoses, and the bleed- tee tting. Remove the bleed-tee tting from the Power Assist module ...

  • Garmin GHP 10V - page 12

    12 GHP 10 Marine Autopilot System Installation Instructions Hydraulic Considerations - Compact 2.1 L Pump Different boats have dif ferent hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. Before starting the hydraulic installation, verify the type of hydraulic steering in your boat, and where to install ...

  • Garmin GHP 10V - page 13

    13 GHP 10 Marine Autopilot System Installation Instructions Compact 2.1 L Pump Hydraulic Layout on Dual-Helm Boats S Balanced cylinder Port tting Starboard tting Compact 2.1 L pump (and motor) Port line Return line Starboard line Shadow Drive Upper helm P R P R S Lower helm Port line Return line Starboard line Notes: Compact 2.1 L pump (and m ...

  • Garmin GHP 10V - page 14

    14 GHP 10 Marine Autopilot System Installation Instructions Compact 2.1 L Pump Hydraulic Layout on SeaStar Power Assist-Enabled Boats Notes: Power Assist module: It may be necessary to remove the Power Assist module to gain access to the ttings, the hoses, and the bleed-tee tting Y ou may need to add a tee tting in the return line at the P ...

  • Garmin GHP 10V - page 15

    15 GHP 10 Marine Autopilot System Installation Instructions Alternative Compact 2.1 L Pump Hydraulic Congurations Depending on the hydraulic layout of your boat, alternative hydraulic installations using the compact 2.1L pump are possible: The C1 and H1 ports are directly connected to each other internally , and the C2 port is directly connected ...

  • Garmin GHP 10V - page 16

    16 GHP 10 Marine Autopilot System Installation Instructions Hydraulic Considerations – Legacy 2.1 L Pump Different boats have dif ferent hydraulic considerations you must examine before mounting the pump or disconnecting any hoses. Before starting the hydraulic installation, verify the type of hydraulic steering in your boat, and where to install ...

  • Garmin GHP 10V - page 17

    17 GHP 10 Marine Autopilot System Installation Instructions Legacy 2.1 L Pump Hydraulic Layout on Dual-Helm Boats Balanced cylinder Port tting Starboard tting Legacy 2.1 L pump (and motor) Port line Return line Starboard line Shadow Drive Upper helm P R S P R S Lower helm Notes: Legacy 2.1 L pump (and motor): Do not use the legacy 2.1 L pump ...

  • Garmin GHP 10V - page 18

    18 GHP 10 Marine Autopilot System Installation Instructions SeaStar Power Assist-Enabled Boats Balanced cylinder Port tting Starboard tting 2.1 L pump (and motor) Port line Return line Starboard line Shadow Drive Helm S R P Sea Star Power Assist module H1 H2 C2 C1 Return line Notes: Power Assist module: It may be necessary to remove the Power ...

  • Garmin GHP 10V - page 19

    19 GHP 10 Marine Autopilot System Installation Instructions Installation Procedures After you have completely planned the GHP 10 installation on your boat, and have satised all the hydraulic, mounting, and wiring considerations for your particular installation, you can begin mounting and connecting the components. Installing the Pump (and Motor) ...

  • Garmin GHP 10V - page 20

    20 GHP 10 Marine Autopilot System Installation Instructions Pump/motor body Upper ttings Lower ttings Pump manifold T o connect the pump to the hydraulic lines: 1. Consult the hydraulic layout diagrams starting on page 9 to nd the correct place to connect the pump to your hydraulic system. 2. Prepare to disconnect the hydraulic lines in yo ...

  • Garmin GHP 10V - page 21

    21 GHP 10 Marine Autopilot System Installation Instructions When the shutoff valve is engaged, the boat will steer normally , and the pump will not control the steering system. When the shutoff valve is engaged, you can remove the pump from the system for repair without disconnecting any hydraulic lines. T o remove the pump from the shutoff-valve m ...

  • Garmin GHP 10V - page 22

    22 GHP 10 Marine Autopilot System Installation Instructions Connecting the Legacy 2.1 L Pump to the Hydraulic Lines The legacy 2.1 L pump must be isolated from the electrical ground of the boat. Use insulating washers under the pump if it is installed on an electrically-grounded (metal) surface. Install the washers between the pump bracket and the ...

  • Garmin GHP 10V - page 23

    23 GHP 10 Marine Autopilot System Installation Instructions Connecting the Pump to the ECU Do not connect the pump to the ECU until you have mounted the ECU to the boat following the procedures on page 25 . Connecting the Compact 2.1 L Pump to the Hydraulic Lines Before disconnecting any hydraulic lines on your boat, consult the manufacturer of you ...

  • Garmin GHP 10V - page 24

    24 GHP 10 Marine Autopilot System Installation Instructions 4. Disconnect the hydraulic lines from the steering system where appropriate. 5. Use the diagram above to identify the connectors on the pump. 6. Remove the plugs from the ve connections on the pump labeled C1, C2, H1, H2, and T ank. 7. Route hydraulic hose from the helm to the pump, an ...

  • Garmin GHP 10V - page 25

    25 GHP 10 Marine Autopilot System Installation Instructions Installing the Electronic Control Unit (ECU) T o install the ECU, mount it to your boat, connect it to the pump and to the CCU, and wire it to the boat battery . Installing the ECU on a 24 Vdc System The ECU hardware has been updated to function with 24 Vdc electrical systems, though older ...

  • Garmin GHP 10V - page 26

    26 GHP 10 Marine Autopilot System Installation Instructions If possible, mount the CCU within 16 ft. (5 m) of the ECU. If you cannot mount the CCU within 16 ft. (5 m) of the ECU, extension and replacement cables are available (see page 4 ). T o mount the CCU bracket: 1. Determine the best location for the CCU on your boat. Use a handheld compass to ...

  • Garmin GHP 10V - page 27

    27 GHP 10 Marine Autopilot System Installation Instructions Wiring the Shadow Drive W ire the Shadow Drive to the CCU/ECU interconnect cable. T o wire the Shadow Drive: 1. Route the bare-wire end of the CCU/ECU interconnect cable to the Shadow Drive. If the cable is not long enough, extend the appropriate wires with 28 A WG wire. 2. Use the Shadow ...

  • Garmin GHP 10V - page 28

    28 GHP 10 Marine Autopilot System Installation Instructions Wiring the Alarm Buzzer W ire the alarm buzzer to the CCU/ECU interconnect cable. T o wire the alarm buzzer: 1. Route the alarm-buzzer cable to the bare-wire end of the CCU/ECU interconnect cable. If the cable is not long enough, extend the appropriate wires with 28 A WG wire. 2. Use the A ...

  • Garmin GHP 10V - page 29

    29 GHP 10 Marine Autopilot System Installation Instructions 7. Drill the four 1 / 8 in. (3.2 mm) pilot holes. Notice If you are mounting the GHC 10 in berglass, it is recommended to use a countersink bit to drill a clearan ce counterbore through only the top gel-coat layer . This will help to avoid any cracking in the gel-co at layer when the sc ...

  • Garmin GHP 10V - page 30

    30 GHP 10 Marine Autopilot System Installation Instructions Connecting the GHC 10 to a NMEA 2000 Network Connect the GHC 10 to the CCU through your existing NMEA 2000 network. If you do not have an existing NMEA 2000 network on your boat, all the parts needed to build one are supplied in the GHP 10 package. Optionally , you can connect a NMEA 2000- ...

  • Garmin GHP 10V - page 31

    31 GHP 10 Marine Autopilot System Installation Instructions 4. Route the included drop cable to the bottom of the T -connector you added to your NMEA 2000 network. If the included drop cable is not long enough, you can use a drop cable up to 20 ft. (6 m) long (not included). 5. Connect the drop cable to the T -connector you added in step 3, and to ...

  • Garmin GHP 10V - page 32

    32 GHP 10 Marine Autopilot System Installation Instructions Notes: T o add additional sensors to your NMEA 2000 network, follow the instructions included with the sensor . The GHC 10 must connect to the CCU with the yellow CCU signal wire in the GHC 10 data cable. The black wire must connect to CCU ground. Connecting an Optional GPS Device to the G ...

  • Garmin GHP 10V - page 33

    33 GHP 10 Marine Autopilot System Installation Instructions If your NMEA 0183-compatible device has only one receiving wire (Rx), connect it to the blue wire (Tx/A) from the GHC 10, and leave the white wire (Tx/B) from the GHC 10 unconnected. Wiring the GHC 10 to a NMEA 0183 Device with One Receiving Wire > > > > > > + - BROWN GRE ...

  • Garmin GHP 10V - page 34

    34 GHP 10 Marine Autopilot System Installation Instructions 2. Connect the black wire (-) to the negative (-) side of the battery rst. 3. Connect the red wire (+) to the positive (+) side of the battery next. 4. Connect the ECU power cable to the ECU last. T o connect the data cable to the GHC 10, align the notches on the cable plug and on the b ...

  • Garmin GHP 10V - page 35

    35 GHP 10 Marine Autopilot System Installation Instructions Conguring the GHP 10 The GHP 10 must be congured and tuned to your boat dynamics and motor conguration. Use the Dockside W izard and the Sea T rial W izard on the GHC 10 to congure the GHP 10. These wizards will walk you through the necessary conguration steps. The Dockside ...

  • Garmin GHP 10V - page 36

    36 GHP 10 Marine Autopilot System Installation Instructions Completing the Sea T rial Wizard: Drive to calm, open water and, if the Sea T rial W izard does not start automatically , select Menu > Setup > Dealer Autopilot Conguration > Wizards > Sea T rial W izard . The Sea T rial W izard welcome screen appears on the GHC 10. Select B ...

  • Garmin GHP 10V - page 37

    37 GHP 10 Marine Autopilot System Installation Instructions Evaluating the Results of the Autopilot Conguration When the Dockside and Sea T rial W izards are complete, test the autopilot to be sure it is congured correctly . T est the autopilot rst at slow speeds (below planing), and then test the autopilot at planing speeds. T o test the ...

  • Garmin GHP 10V - page 38

    38 GHP 10 Marine Autopilot System Installation Instructions Advanced Conguration Power-on Procedure Advanced conguration options are not available on the GHC 10 under normal conditions. T o access the advanced conguration settings of the GHP 10, use the advanced conguration power-on procedure. T o access the wizards and advanced cong ...

  • Garmin GHP 10V - page 39

    39 GHP 10 Marine Autopilot System Installation Instructions Category Setting Description T achometer Setup V erify T achometer With the engine (or engines) running, compare the RPM readings on the GHC 10 with the tachometer on the dashboard of your boat. Adjust the Pulses Per Rev with the arrows if the values do not match, and then select Done . Wh ...

  • Garmin GHP 10V - page 40

    40 GHP 10 Marine Autopilot System Installation Instructions Appendix Specications ECU Physical Dimensions (W×H×D): 6 19 / 32 × 4 19 / 32 × 2 in. (167.6 × 1 16.8 × 50.8 mm) W eight: 1.5 lb. (0.68 kg) T emperature Range: from 5°F to 131°F (from -15°C to 55°C) Case Material: Fully gasketed, high-impact aluminum alloy , waterproof to IEC 5 ...

  • Garmin GHP 10V - page 41

    41 GHP 10 Marine Autopilot System Installation Instructions Legacy 2.1L Pump Physical Dimensions (W×H×D): 15 × 7 1 / 2 × 7 3 / 16 in. (381 ×190.5 × 182.9 mm) W eight: 17.6 lb. (8 kg) T emperature Range: From 5°F to 131°F (from -15°C to 55°C) Cable Length: 19 in. (0.5 m) Power Main Power Usage: V aries based on hydraulic loading Shadow Dri ...

  • Garmin GHP 10V - page 42

    42 GHP 10 Marine Autopilot System Installation Instructions NMEA 2000 PGN Information GHC 10 Receive T ransmit 059392 ISO Acknowledgment 059392 ISO Acknowledgment 059904 ISO Request 059904 ISO Request 060928 ISO Address Claim 060928 ISO Address Claim 126208 NMEA - Command/Request/Acknowledge Group Function 126208 NMEA - Command/Request/Acknowledge ...

  • Garmin GHP 10V - page 43

    43 GHP 10 Marine Autopilot System Installation Instructions Mounting T emplates Use the following mounting templates to assist with the mounting process. ECU Mounting T emplate CCU Mounting T emplate Up (when mounting on a vertical surface) ...

  • Garmin GHP 10V - page 44

    44 GHP 10 Marine Autopilot System Installation Instructions ...

  • Garmin GHP 10V - page 45

    45 GHP 10 Marine Autopilot System Installation Instructions 1.2 L/2.0 L Pump Mounting T emplate ...

  • Garmin GHP 10V - page 46

    46 GHP 10 Marine Autopilot System Installation Instructions Compact 2.1 L Pump Mounting T emplate NOTE: This template should also be used with the legacy 2.1 L pump. Manifold ...

  • Garmin GHP 10V - page 47

    47 GHP 10 Marine Autopilot System Installation Instructions GHP 10 Installation Checklist Detach this checklist from the installation instructions and use it to assist with the GHC 10 installation process. Read all installation instructions before installing the GHC 10. Contact Garmin Product Support if you have any questions during the installatio ...

  • Garmin GHP 10V - page 48

    © 2010 Garmin Ltd. or its subsidiaries All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of t ...

Manufacturer Garmin Category Marine Instruments

Documents that we receive from a manufacturer of a Garmin GHP 10V can be divided into several groups. They are, among others:
- Garmin technical drawings
- GHP 10V manuals
- Garmin product data sheets
- information booklets
- or energy labels Garmin GHP 10V
All of them are important, but the most important information from the point of view of use of the device are in the user manual Garmin GHP 10V.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Garmin GHP 10V, service manual, brief instructions and user manuals Garmin GHP 10V. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Garmin GHP 10V.

Similar manuals

A complete manual for the device Garmin GHP 10V, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Garmin GHP 10V by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Garmin GHP 10V.

A complete Garmin manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Garmin GHP 10V - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Garmin GHP 10V, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Garmin GHP 10V, that we can find in the current document
3. Tips how to use the basic functions of the device Garmin GHP 10V - which should help us in our first steps of using Garmin GHP 10V
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Garmin GHP 10V
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Garmin GHP 10V in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Garmin GHP 10V?

Use the form below

If you did not solve your problem by using a manual Garmin GHP 10V, ask a question using the form below. If a user had a similar problem with Garmin GHP 10V it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)