Manual Husqvarna HUV 4213-G

52 pages 2.41 mb
Download

Go to site of 52

Summary
  • Husqvarna HUV 4213-G - page 1

    2008 HUV 4213-G and HUV 4213-GXP Owner ’ s Manual Gasoline Utility V ehicles ...

  • Husqvarna HUV 4213-G - page 2

    ...

  • Husqvarna HUV 4213-G - page 3

    NOTICE W arranty information appears at the end of this manual. No other warranties, express or implied, are contained herein. Y our authorized representative checked the vehicle before it was delivered to you and will provide you a copy of the completed vehicle warranty registration form. Husqvarna is not liable for errors in this manual or for in ...

  • Husqvarna HUV 4213-G - page 4

    FOREWORD Thank you for choosing Husqvarna, a world leader in outdoor products. Y ou have chosen the nest utility vehicle on the market. Please protect your investment and ensure that your Husqvarna vehicle provides years of reliable, superior performance by reading and following the maintenance instructions in this manual. Y our comfort and safe ...

  • Husqvarna HUV 4213-G - page 5

    T ABLE OF CONTENTS Safety Decal and Feature Identication .. . . . . .. . . . . . .. . . . . .. . . . . .. . . . . . .. . . . . .. . . . . . .. . . . . .. . . . . . .. . . . . .. . . . . .. . . . . . .. . . . . .. . . . . . .. . . . . .. . . . . . .. . . . . .. . . . 4 Practice Safety . .. . . . . . .. . . . . .. . . . . . .. . . . . .. . . . . . ...

  • Husqvarna HUV 4213-G - page 6

    Safety Decal and Feature Identication SAFETY DECAL AND FEA TURE IDENTIFICA TION The following pages contain safety decal and feature identication information. For detailed information on specic features, read the appropriate section in this manual. Page 4 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual ...

  • Husqvarna HUV 4213-G - page 7

    Safety Decal and Feature Identication HUV 4213-G/4213-GXP 347 5 3 9 7 1 11 8 2 12 13 14 4 6 16 15 10 1 101553901 Decal, Bed Loading W arning (on cargo bed or seat back) 9 102224301 Decal, Operating Instructions (on steering wheel) 2 101609401 Decal, Crush Area W arning (behind seat, near cargo bed) 10 Serial Number 3 101825102 Decal, On/Of f/Sta ...

  • Husqvarna HUV 4213-G - page 8

    Safety Decal and Feature Identication HUV 4213-G/4213-GXP 348 2 9 8 10 7 4 11 3 6 5 12 1 1 101 1553 Decal, T railer Hitch T ongue Weight Notice (on trailer/receiver hitch) 7 102459301 Decal, Bed Latch W arning (on vehicle body , below bed latch) 2 101547601 Decal, Gasoline Fuel W arning (at fuel ll or on frame, near fuel tank) 8 Forward/Rever ...

  • Husqvarna HUV 4213-G - page 9

    Practice Safety PRACTICE SAFETY 399 Figure 1 Practice Safety Safety signs like you see above may at rst seem shocking, but their impact is mild compared with the reality of severe personal injury . Y our safety and satisfaction are of the utmost importance to us. That is why before operating the vehicle, we urge you to review the information in ...

  • Husqvarna HUV 4213-G - page 10

    Safety Details SAFETY DET AILS W ARNING • This owner’s manual should be read completely before attempting to drive or service the vehicle. Failure to follow the instructions in this manual could result in property damage, severe personal injury , or death. It is important to note that some vital statements throughout this manual and on the deca ...

  • Husqvarna HUV 4213-G - page 11

    General Warnings 1 2 (Viewed from passenger side of vehicle) 1. Remove negative battery cable. 2. Remove positive battery cable. Connect battery cables in reverse order . 1 Figure 2 Battery Cable Removal GENERAL W ARNINGS The following safety statements listed must be heeded whenever the vehicle is being operated, repaired, or serviced. See Safety ...

  • Husqvarna HUV 4213-G - page 12

    Model Identication W ARNING • Follow the procedures exactly as stated in this manual, and heed all DANGER, W ARNING, and CAUTION statements in this manual as well as those on the vehicle. • Do not leave children unattended on vehicle. • Prior to leaving the vehicle unattended or servicing the vehicle, set the park brake, place the Forward/ ...

  • Husqvarna HUV 4213-G - page 13

    Controls and Indicators SERIAL NUMBER HH0601-583947 7349 ST ATESVILLE RD. CHARLOTTE, NC 28269 47 Figure 3 Serial Number CONTROLS AND INDICA T ORS See General W arnings on page 9. W ARNING • Before allowing anyone to drive the vehicle, make sure the driver is familiar with all controls and operating procedures. • Do not tamper with the governor ...

  • Husqvarna HUV 4213-G - page 14

    Controls and Indicators KEY SWITCH The key switch is mounted on the instrument panel to the right of the steering column (Figure 4) . It has three positions: OFF , ON and ST AR T . T o start the vehicle, place the Forward/Reverse handle in the NEUTRAL position and turn the key past the ON position to the ST ART position and hold until the engine is ...

  • Husqvarna HUV 4213-G - page 15

    Controls and Indicators F N R 159 Figure 5 Forward/Reverse Handle ACCELERA T OR PEDAL The accelerator pedal is the pedal on the right, with the word GO molded into it (Figure 6) . With the engine running and the Forward/Reverse handle in the FOR W ARD or REVERSE position, vehicle speed will increase as the accelerator pedal is pressed. When the acc ...

  • Husqvarna HUV 4213-G - page 16

    Controls and Indicators BRAKE PEDAL The brake pedal is the large pedal on the left with the word ST OP molded into it (Figure 6) . T o slow or stop the vehicle, press the brake pedal (Figure 7) . P ARK BRAKE The park brake handle is located between the driver and passenger seats. T o engage the park brake, rst apply pressure to the brake pedal, ...

  • Husqvarna HUV 4213-G - page 17

    Controls and Indicators 162 Figure 9 Choke 163 Figure 10 Differential Lock DIFFERENTIAL LOCK W ARNING • With the differential lock engaged, vehicle turning functions are greatly reduced. T o prevent loss of vehicle control when differential lock is engaged, do not operate vehicle at speeds greater than half throttle and use caution when attemptin ...

  • Husqvarna HUV 4213-G - page 18

    Seat Latch and Adjustment 164 Figure 1 1 Low Oil W arning Light FUEL GAUGE/HOUR METER A fuel gauge and hour meter are housed together at the lower left corner of the instrument panel. The fuel gauge operates when the key switch is in the ON position, and allows the operator to monitor the fuel level in the vehicle. The hour meter operates only when ...

  • Husqvarna HUV 4213-G - page 19

    Pre-Operation and Daily Safety Checklist The bucket seats on all vehicles are adjustable and can be moved forward or backward to accommodate the driver or passenger . T o adjust a seat: 1. Remove the seat from the vehicle. 2. Remove the four bolts and washers from the bottom of the seat mounting plate. 3. Align the mounting plate holes with holes i ...

  • Husqvarna HUV 4213-G - page 20

    Driving Instructions Use the following checklist, in conjunction with the Pre-Operation and Daily Safety Checklist, as a guide to inspect the vehicle and check daily for proper operation. Any problems should be corrected by a Husqvarna distributor/dealer or a trained technician. • Forward/Reverse shifter: Check for proper operation. See Controls ...

  • Husqvarna HUV 4213-G - page 21

    Driving Instructions W ARNING – Be sure all passengers are capable of securing themselves in a vehicle before allowing them to ride in one. • Do not shift the Forward/Reverse handle while the vehicle is in motion. • Stop the vehicle before shifting the Forward/Reverse handle. Engine must be at idle before shifting the Forward/Reverse handle. ...

  • Husqvarna HUV 4213-G - page 22

    Driving Instructions 9. Release park brake. 10. Keeping brake engaged, place the Forward/Reverse handle in desired position (F = forward or R = reverse). Engine must be at idle before moving the shift handle. A buzzer will sound as a warning when the vehicle is in the REVERSE position. 1 1. Release brake pedal and slowly press accelerator pedal. As ...

  • Husqvarna HUV 4213-G - page 23

    Bed Latch and Prop Rod BED LA TCH AND PROP ROD See General W arnings on page 9. DANGER • Use caution when working under bed. Be sure prop rod is secure. Otherwise the bed will fall, resulting in severe personal injury or death. W ARNING • For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle. If the vehi ...

  • Husqvarna HUV 4213-G - page 24

    Loading and Unloading LOADING AND UNLOADING W ARNING • Firmly engage park brake before loading vehicle. • Do not allow riders in the cargo bed. • Reduce vehicle load and speed when driving up or down slopes or on uneven terrain. • Do not exceed rated vehicle capacity . Rated capacity is for level surfaces only . • Overloading can affect v ...

  • Husqvarna HUV 4213-G - page 25

    T owing with the V ehicle TOWING WITH THE VEHICLE W ARNING • Do not tow a vehicle or trailer on public streets or highways. • Normal vehicle operating speed should be reduced when towing. • Extreme caution should be used when towing. • Do not allow riders in the vehicle or trailer being towed. • A void sudden starts, sudden stops, and tig ...

  • Husqvarna HUV 4213-G - page 26

    Storage STORAGE See General W arnings on page 9. DANGER • Do not attempt to drain fuel when the engine is hot or while it is running. • Be sure to clean up any spilled gasoline before operating the vehicle. • Store fuel in an approved fuel container only . Store in a well-ventilated area away from sparks, open ames, heaters, or heat source ...

  • Husqvarna HUV 4213-G - page 27

    Storage 7. Disconnect the battery cables, negative (–) cable rst. See W ARNING “T o avoid unintentionally starting...” in General W arnings on page 9. 8. Batteries should be clean and free of corrosion. W ash tops and terminals of batteries with a solution of baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). ...

  • Husqvarna HUV 4213-G - page 28

    Maintenance 4.1. Remove plug from fuel tank vent. 4.2. Connect vent tube to fuel tank vent. 5. Connect battery cables, positive (+) cable rst, and tighten terminals to 144 in-lb (16 N·m). Coat terminals with Battery T erminal Protector Spray (P/N 603 00 00-03). 6. Completely open the fuel shut-off valve (Figure 14) . Make sure the valve is full ...

  • Husqvarna HUV 4213-G - page 29

    Periodic Service Schedule W ARNING • T o help avoid unintentionally starting the vehicle: – Disconnect battery cables, negative (–) cable rst (Figure 2). – Disconnect the spark plug wire from the spark plug. • If wires are removed or replaced make sure wiring and wire harness are properly routed and secured. Failure to properly route a ...

  • Husqvarna HUV 4213-G - page 30

    Periodic Service Schedule PERIODIC SER VICE SCHEDULE REGULAR INTERV AL SERVICE Pre-Operation and Daily Safety Checklist See Pre-Operation and Daily Safety Checklist on page 17. Daily service by owner Performance Inspection See Performance Inspection on page 17. Check engine oil level; change as required. See Periodic Lubrication Schedule on page 29 ...

  • Husqvarna HUV 4213-G - page 31

    Periodic Lubrication Schedule PERIODIC LUBRICA TION SCHEDULE PERIODIC LUBRICA TION SCHEDULE REGULAR INTER V AL SERVICE LUBRICA TION POINTS RECOMMENDED LUBRICANT Brake pedal shaft bearings 1 Dry Moly Lube (P/N 603 00 00-01) Accelerator push rod pivots, mounts, and shifter cable pivots 2 Dry Moly Lube (P/N 603 00 00-01) Semiannually by owner or train ...

  • Husqvarna HUV 4213-G - page 32

    Master Cylinder MASTER CYLINDER 1 2 3 1. Full Level 2. Safe Level 3. Low Level 168 Figure 16 Brake Fluid Reservoir The master cylinder is located under the passenger seat toward the center of the vehicle (Figure 16) . Raise or remove the seat to check the brake uid level. When checking the brake uid, also inspect the following: • The presen ...

  • Husqvarna HUV 4213-G - page 33

    Engine Oil ENGINE OIL Even though the low oil warning light on the instrument panel should illuminate if oil becomes low , the engine oil level should be checked monthly . The vehicle should be on a level surface when checking oil. Do not overll with oil. ENGINE OIL LEVEL CHECK 1. Remove the oil level dipstick from the oil ller tube and wipe ...

  • Husqvarna HUV 4213-G - page 34

    Engine Oil W ARNING • For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle. If the vehicle is equipped with a prop rod, ensure that it is securely engaged while bed is raised. Do not close the bed until all persons are clear of cargo bed area. Keep hands clear of all crush areas. Do not drop cargo bed; lo ...

  • Husqvarna HUV 4213-G - page 35

    Engine Oil 10. Remove the engine oil lter , turning it counterclockwise, allowing the residual oil in the lter port and lter to drain into the oil drain pan. See following NOTE NOTE: An oil drip guard can be used to prevent excess oil from dripping into the engine base place. Use an empty quart (one liter) container and cut the bottom off ...

  • Husqvarna HUV 4213-G - page 36

    Engine Oil 27 Figure 21 Coat Rubber Seal 172 Figure 22 Add Engine Oil 13. Tighten the oil lter by hand until tight. Do not use a band wrench or channel lock plier to tighten. 14. Lower the vehicle and remove the oor jack from under the rear of the vehicle. 15. Remove the dipstick and add engine oil into the dipstick port. Use a funnel or pour ...

  • Husqvarna HUV 4213-G - page 37

    Fueling Instructions NOTE: Using multi-grade oils (5W-20, 10W-30, and 10W-40) will increase oil consumption. Check oil level more frequently when using them. FUELING INSTRUCTIONS See General W arnings on page 9. DANGER • T urn the key switch to the OFF position before fueling. • Do not pour fuel into the fuel tank when the engine is hot or whil ...

  • Husqvarna HUV 4213-G - page 38

    Battery 1 4 5 3 2 1. V ent T ube 2. T o Carburetor 3. V ent 4. Fuel Shut-of f V alve 5. Fuel T ank 173 Figure 24 Fuel T ank BA TTER Y See General W arnings on page 9. DANGER • Battery – Explosive gases! Do not smoke. Keep sparks and ames away from the vehicle and service area. V entilate when charging or operating vehicle in an enclosed area ...

  • Husqvarna HUV 4213-G - page 39

    Battery 2. Access the engine compartment. See W ARNING “For vehicles with cargo beds...” in General W arnings on page 9. 3. T ilt the bed and ensure that the prop rod is properly engaged. 4. Disconnect the battery cables, negative (–) cable rst. See W ARNING “T o avoid unintentionally starting...” in General W arnings on page 9. 5. Use ...

  • Husqvarna HUV 4213-G - page 40

    Cleaning the V ehicle CLEANING THE VEHICLE Each vehicle is equipped with an ABS/DR acrylic front body and an all-aluminum rear body . The HUV4213 has a powder-coated steel cargo bed. Use commercial automotive cleaning solutions with a sponge or soft cloth for normal cleaning. A garden hose at normal residential water pressure is adequate. T o remov ...

  • Husqvarna HUV 4213-G - page 41

    Subsequent Owner Registration CAUTION • Use of the winch for an extended period of time could discharge the battery . Keep winch operations as short as possible, and drive the vehicle for several minutes after the winch operation to recharge the battery . SUBSEQUENT OWNER REGISTRA TION In the event a vehicle is bought as a used vehicle, we strong ...

  • Husqvarna HUV 4213-G - page 42

    V ehicle Specications VEHICLE SPECIFICA TIONS SPECIFICA TIONS HUV4213-GXP HUV4213-G POWER SOURCE Engine: 4-cycle OHV , 400 cc, 13.0 maximum HP @3600 RPM (per SAE J 1940/1349), single-cylinder , air-cooled, with pressure lubrication system • Fuel system: Side-draft carburetor with oat bowl, xed jets, fuel lters, and impulse fuel pump ? ...

  • Husqvarna HUV 4213-G - page 43

    V ehicle Specications SPECIFICA TIONS HUV4213-GXP HUV4213-G Curb clearance circle (diameter) 24 ft. 1 in. (734 cm) T urning radius (per SAE J 695) 139.6 in. (355 cm) Intersecting aisle clearance 1 12.2 in (285 cm) Floorboard height 17 in. (43 cm) Seat height 35 in. (89 cm) Load bed height 31.1 in. (79 cm) Load bed size (box bed inside dimensions ...

  • Husqvarna HUV 4213-G - page 44

    Warranties W ARRANTIES HUSQV ARNA® LIMITED TWO YEAR W ARRANTY FOR 2008 TRANSPORT A TION AND UTILITY VEHICLES 1. W ARRANTY : Husqvarna, INC., ("Husqvarna") hereby warrants to the Original Retail Purchaser that its new 2008 Model T ransportation and Utility V ehicles purchased from Husqvarna or an authorized dealer shall be free from defec ...

  • Husqvarna HUV 4213-G - page 45

    Warranties 5. HOW T O MAKE A W ARRANTY CLAIM: T o make a warranty claim under this limited warranty , you must present the vehicle or defective component to an authorized Husqvarna dealer . 6. DISCLAIMER: THIS LIMITED W ARRANTY IS EXCLUSIVE. HUSQV ARNA MAKES NO OTHER W ARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ANY IMPLIED W ARRANTIES OF MERCHANT A ...

  • Husqvarna HUV 4213-G - page 46

    Warranties CALIFORNIA EMISSION CONTROL W ARRANTY ST A TEMENT Y our new Husqvarna ("Husqvarna") vehicle engine complies with both the U.S. EP A and State of California emission regulations. However , the use of gasoline powered golf cars in areas of California that do not attain the federal ozone standards is illegal. Please refer to the A ...

  • Husqvarna HUV 4213-G - page 47

    Warranties (5) Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to service the subject engines or equipment. (6) The engine or equipment owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-related ...

  • Husqvarna HUV 4213-G - page 48

    Warranties NECESSARY MAINTENANCE AS OUTLINED IN THE OWNERS MANUAL AND MAINTENANCE AND SERVICE MANUAL W AS NOT PERFORMED A T THE TIME AND IN THE MANNER SPECIFIED IN SUCH MANUALS. 5. NO CONSEQUENTIAL DAMAGES: In no event shall Husqvarna be liable for any incidental or consequential damages including, but not limited to, loss related to property other ...

  • Husqvarna HUV 4213-G - page 49

    ...

  • Husqvarna HUV 4213-G - page 50

    ...

  • Husqvarna HUV 4213-G - page 51

    ...

  • Husqvarna HUV 4213-G - page 52

    Publication Part Number 603 00 43-23 Edition Code 0707C0608B 103372939 ...

Manufacturer Husqvarna Category Utility Vehicle

Documents that we receive from a manufacturer of a Husqvarna HUV 4213-G can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- HUV 4213-G manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna HUV 4213-G
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna HUV 4213-G.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna HUV 4213-G, service manual, brief instructions and user manuals Husqvarna HUV 4213-G. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna HUV 4213-G.

A complete manual for the device Husqvarna HUV 4213-G, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna HUV 4213-G by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna HUV 4213-G.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna HUV 4213-G - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna HUV 4213-G, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna HUV 4213-G, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna HUV 4213-G - which should help us in our first steps of using Husqvarna HUV 4213-G
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna HUV 4213-G
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna HUV 4213-G in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna HUV 4213-G?

Use the form below

If you did not solve your problem by using a manual Husqvarna HUV 4213-G, ask a question using the form below. If a user had a similar problem with Husqvarna HUV 4213-G it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)